Re: USB disk speed regression WD Elements - with bisect result 22547c4cc4fe20698a6a85a55b8788859134b8e4

[Zdenek Kabelac <zkabelac@redhat.com>]

Dne 27.7.2017 v 03:03 Alan Stern napsal(a):
> [Added linux-usb mailing list to CC:]
> 
> Short description of bug: In 4.12 or later, when Zdenek's Western
> Digital disk is attached to an EHCI controller, it ends up connecting
> at full speed to the companion UHCI controller instead.  But when
> commit 22547c4cc4fe ("usb: hub: Wait for connection to be reestablished
> after port reset")  is reverted, the disk connects correctly at high
> speed.
> 
> On Wed, 26 Jul 2017, Zdenek Kabelac wrote:
> 
>> Dne 25.7.2017 v 21:50 Alan Stern napsal(a):
>>> On Tue, 25 Jul 2017, Zdenek Kabelac wrote:
>>>
>>>
>>> 08:18 usb 2-2: USB disconnect, device number 2
>>> 08:25 usb 2-2: new high-speed USB device number 3 using ehci-pci
>>> 08:26 usb 2-2: new high-speed USB device number 4 using ehci-pci
>>>
>>> If the drive were working entirely correctly, it wouldn't do that.
>>>
>>> We could continue futzing around with hardware and driver tests for a
>>> long time.  But there may be a shortcut: If you have a USB hub, you
>>> could try attaching the drive through it.  It's entirely possible that
>>> this will fix the problem.
>>>
>>> If not, you'll have to start doing some very detailed tests.  As a
>>> start, you can enable debugging for the usbcore and ehci_hcd drivers
>>> immediately before the test:
>>>
>>> echo 'module usbcore =p' >/sys/kernel/debug/dynamic_debug/control
>>> echo 'module ehci_hcd =p' >/sys/kernel/debug/dynamic_debug/control
>>> dmesg -C
>>>
>>> Then after the test, see what shows up in the dmesg output.  And again,
>>> we'll want to do a comparison.  In fact, 4.12 with and without the
>>> commit you identified would make a better comparison than 4.12 vs. 4.8.
>>>
>>
>>
>> Hi
>>
>>
>> So here we go with traces - made with freshly compiled recent 4.13-rc2.
>> OK trace is with revert patch applied.
>> BAD trace is the one with it (essentially vaniala master).
>>
>> Trace also has KOBJECT debugging enabled - I think difference is
>> nicely visible between them - but I've no explanation for it.
>>
>> Both traces start with cable detach followed with attachment.
> 
> Okay, I figured out the cause.
> 
> The USB stack assumes that if a high-speed device initialization fails
> and the device is still connected, it means that the device can't run
> properly at high speed and the computer needs to try again at full
> speed.  See commit 90da096ee46b ("USB: force handover port to companion
> when hub_port_connect_change fails").
> 
> In Zdenek's case, the device really does disconnect itself before the
> second port reset.  If 22547c4cc4fe is present, it causes an extra
> delay -- some 200 ms -- long enough for the device to reconnect again.
> So we appear to be in the situation described above, and the connection
> is switched over to the companion controller.
> 
> If 22547c4cc4fe is not present, the kernel sees that the device is not
> connected at the end of the second reset and gives up trying to
> initialize the device.  When the device reconnects about 140 ms later,
> the kernel treats it as a new connection and successfully negotiates a
> high-speed link.
> 
> Zdenek, you check this explanation by commenting out these last two
> lines at the end of hub_port_connect() in drivers/usb/core/hub.c:
> 
> 	if (hcd->driver->relinquish_port && !hub->hdev->parent)
> 		hcd->driver->relinquish_port(hcd, port1);
> 
> That should prevent the connection from being handed over to the UHCI
> companion, allowing the device to operate at high speed.
>

Hi

Yep - seems this helped - I've dropped revert and commented those 2 lines
and I've used the very same kernel - and speed was all good:

usb 2-2: new high-speed USB device number 2 using ehci-pci
usb 2-2: new high-speed USB device number 3 using ehci-pci
usb 2-2: New USB device found, idVendor=1058, idProduct=10a8
usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3


So while I'm not sure if this is final fix for USB - this solution surely 
solved my WD Element disk attachment issue.

Regards

Zdenek