[PATCH 0/7] arm64: dts: qcom: shikra: Add display overlays for EVK boards

[PATCH 0/7] arm64: dts: qcom: shikra: Add display overlays for EVK boards

[vishnu.saini]

Shikra EVK SoC cards (CQS, CQM, and IQS) are mounted on the Lyra carrier
card. The DSI0 interface from SoC card is routed to either the 22-pin DSI
connector on carrier card named as JDISP1 DSI0 or to the B2B connector
named as PDISP1 DSI0, though a MUX which can be selected by a hardware
DIP switch. There are multiple daughter cards designed that can be
connected to this PDISP1 DSI0 B2B connector.

The below B2B display interfaces are enabled by default in base DTB:
- IQS: DSI-to-HDMI using the LT9611UXD daughter card
- CQS/CMS: DLC0697 DSI panel using a DLC daughter card

This series adds DT overlays for additional display configurations:

- shikra-cqm-cqs-evk-hdmi: HDMI output for CQM/CQS with LT9611UXD
  daughter card
- shikra-iqs-evk-dlc-panel: DLC0697 DSI panel for IQS with DLC daughter
  card
- shikra-iqs-evk-lvds-auo,g133han01: AUO G133HAN01 LVDS panel for IQS
  with LVDS daughter card
- shikra-iqs-evk-raspberrypi-dsi-7inch: Raspberry Pi 7-inch DSI
  panel with touch via the 22-pin JDISP1 DSI0 connector for IQS
- shikra-iqs-evk-waveshare-dsi-8inch: Waveshare 8-inch DSI panel
  with touch via the 22-pin JDISP1 DSI0 connector for IQS

These overlays are applied on top of the corresponding base board
DTBs.

Signed-off-by: Vishnu Saini <vishnu.saini@oss.qualcomm.com>
---
Anand Tiwari (1):
      arm64: dts: qcom: shikra-iqs-evk: Add AUO G133HAN01 LVDS panel overlay

Mohit Dsor (1):
      arm64: dts: qcom: shikra-cqm-evk, shikra-cqs-evk: Add HDMI overlay

Shashank Maurya (2):
      arm64: dts: qcom: shikra-iqs-evk: Add RPi 7-inch DSI panel overlay
      arm64: dts: qcom: shikra-iqs-evk: Add Waveshare 8-inch DSI panel overlay

Vishnu Saini (3):
      arm64: dts: qcom: shikra-iqs-evk: Add DLC0697 panel overlay
      arm64: defconfig: Enable RPi touchscreen V2 regulator and ILI9881C panel
      arm64: defconfig: Enable Waveshare DSI panel and touch GPIO drivers

 arch/arm64/boot/dts/qcom/Makefile                  |  15 +++
 .../boot/dts/qcom/shikra-cqm-cqs-evk-hdmi.dtso     |  90 +++++++++++++++
 .../boot/dts/qcom/shikra-iqs-evk-dlc-panel.dtso    |  78 +++++++++++++
 .../qcom/shikra-iqs-evk-lvds-auo,g133han01.dtso    | 127 +++++++++++++++++++++
 .../qcom/shikra-iqs-evk-raspberrypi-dsi-7inch.dtso |  91 +++++++++++++++
 .../qcom/shikra-iqs-evk-waveshare-dsi-8inch.dtso   |  77 +++++++++++++
 arch/arm64/configs/defconfig                       |   4 +
 7 files changed, 482 insertions(+)
---
base-commit: 6474fa070f2b8013b4b87350b775b8c3be6e8aac
change-id: 20261019-shikra_display_overlays-515c88f150b3
prerequisite-message-id: <20260930-shikra-dt-changes-v5-0-8eaf658a0e38@oss.qualcomm.com>
prerequisite-patch-id: 7631efa76e1fe98ae45c0f68e93ced4c523af27a
prerequisite-patch-id: 49396fb33427bd9b9214b537221a1c582d5d62ee
prerequisite-patch-id: 3cbb70da0a3009a2730813b562c29f432bd0fd8f
prerequisite-patch-id: 1c9ff594613a4cef8d605cfd37a3270866ba6414
prerequisite-message-id: <20261015-shikra-work-v5-0-5e075222b60a@oss.qualcomm.com>
prerequisite-patch-id: 326d8620d592d8f5f75fe62f88a2cb4dd8ec0b46
prerequisite-patch-id: 327308970dffdb2b218d4834e1badcc9e05cfd01
prerequisite-message-id: <20261008-lt9611c-v7-v17-0-1e8f5f2b2f19@oss.qualcomm.com>
prerequisite-patch-id: 49f1e01bb5594ce9c4301ce4b16715834ece7f41
prerequisite-patch-id: b909fe50eb311c7d8ca6778a29952e2c1a28d7ee

Best regards,
-- 
Vishnu Saini <vishnu.saini@oss.qualcomm.com>

[PATCH 1/7] arm64: dts: qcom: shikra-cqm-evk, shikra-cqs-evk: Add HDMI overlay

[vishnu.saini]

From: Mohit Dsor <mohit.dsor@oss.qualcomm.com>

Add a DT overlay for CQM and CQS, to enable HDMI output when LT9611UXD
DSI-to-HDMI daughter card connected to PDISP1 DSI0 on carrier card.
LT9611UXD is connected through I2C4, with reset and interrupt connected
to tlmm GPIO76 and GPIO85.

Disable the default DSI0 panel dt nodes and enable LT9611UXD
bridge for HDMI output.

Signed-off-by: Mohit Dsor <mohit.dsor@oss.qualcomm.com>
Signed-off-by: Vishnu Saini <vishnu.saini@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/Makefile                  |  6 ++
 .../boot/dts/qcom/shikra-cqm-cqs-evk-hdmi.dtso     | 90 ++++++++++++++++++++++
 2 files changed, 96 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 4e714251d5e6..c8907e77c893 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -377,6 +377,12 @@ shikra-iqs-evk-imx577-camera-dtbs	:= shikra-iqs-evk.dtb shikra-iqs-evk-imx577-ca
 dtb-$(CONFIG_ARCH_QCOM)	+= shikra-cqm-evk-imx577-camera.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= shikra-cqs-evk-imx577-camera.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= shikra-iqs-evk-imx577-camera.dtb
+
+shikra-cqm-evk-hdmi-dtbs	:= shikra-cqm-evk.dtb shikra-cqm-cqs-evk-hdmi.dtbo
+shikra-cqs-evk-hdmi-dtbs	:= shikra-cqs-evk.dtb shikra-cqm-cqs-evk-hdmi.dtbo
+
+dtb-$(CONFIG_ARCH_QCOM)	+= shikra-cqm-evk-hdmi.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= shikra-cqs-evk-hdmi.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm4250-oneplus-billie2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm4450-qrd.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm6115-fxtec-pro1x.dtb
diff --git a/arch/arm64/boot/dts/qcom/shikra-cqm-cqs-evk-hdmi.dtso b/arch/arm64/boot/dts/qcom/shikra-cqm-cqs-evk-hdmi.dtso
new file mode 100644
index 000000000000..a7b77114061a
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/shikra-cqm-cqs-evk-hdmi.dtso
@@ -0,0 +1,90 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+&{/} {
+	model = "Qualcomm Technologies, Inc. Shikra CQM/S EVK HDMI";
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_out: endpoint {
+				remote-endpoint = <&hdmi_bridge_out>;
+			};
+		};
+	};
+};
+
+&i2c4 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	status = "okay";
+
+	hdmi-bridge@41 {
+		compatible = "lontium,lt9611uxd";
+		reg = <0x41>;
+		interrupts-extended = <&tlmm 85 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&tlmm 76 GPIO_ACTIVE_LOW>;
+		vcc-supply = <&lcd_bias>;
+		vdd-supply = <&pm4125_l15>;
+		pinctrl-0 = <&bridge_irq_pin &bridge_rst_pin>;
+		pinctrl-names = "default";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				hdmi_bridge_in: endpoint {
+					remote-endpoint = <&mdss_dsi0_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				hdmi_bridge_out: endpoint {
+					remote-endpoint = <&hdmi_connector_out>;
+				};
+			};
+		};
+	};
+};
+
+&mdss_dsi0 {
+	panel@0 {
+		status = "disabled";
+	};
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&hdmi_bridge_in>;
+};
+
+&tlmm {
+	bridge_rst_pin: bridge-rst-state {
+		pins = "gpio76";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	bridge_irq_pin: bridge-irq-state {
+		pins = "gpio85";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};

-- 
2.34.1

[PATCH 2/7] arm64: dts: qcom: shikra-iqs-evk: Add DLC0697 panel overlay

[Vishnu Saini]

Add a DT overlay for IQS, to enable DLC0697 panel when DLC daughter card
connected to PDISP1 DSI0 on carrier card.
Configure DLC0697 reset GPIO, supplies, pinctrl states and GPIO backlight
controlled through PM8150 GPIO 1.

Disable the default HDMI bridge and connector in favour of the DSI
panel.

Signed-off-by: Vishnu Saini <vishnu.saini@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/Makefile                  |  3 +
 .../boot/dts/qcom/shikra-iqs-evk-dlc-panel.dtso    | 78 ++++++++++++++++++++++
 2 files changed, 81 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index c8907e77c893..0c5a7b7f694b 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -380,9 +380,12 @@ dtb-$(CONFIG_ARCH_QCOM)	+= shikra-iqs-evk-imx577-camera.dtb
 
 shikra-cqm-evk-hdmi-dtbs	:= shikra-cqm-evk.dtb shikra-cqm-cqs-evk-hdmi.dtbo
 shikra-cqs-evk-hdmi-dtbs	:= shikra-cqs-evk.dtb shikra-cqm-cqs-evk-hdmi.dtbo
+shikra-iqs-evk-dlc-panel-dtbs	:= shikra-iqs-evk.dtb shikra-iqs-evk-dlc-panel.dtbo
 
 dtb-$(CONFIG_ARCH_QCOM)	+= shikra-cqm-evk-hdmi.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= shikra-cqs-evk-hdmi.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= shikra-iqs-evk-dlc-panel.dtb
+
 dtb-$(CONFIG_ARCH_QCOM)	+= sm4250-oneplus-billie2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm4450-qrd.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm6115-fxtec-pro1x.dtb
diff --git a/arch/arm64/boot/dts/qcom/shikra-iqs-evk-dlc-panel.dtso b/arch/arm64/boot/dts/qcom/shikra-iqs-evk-dlc-panel.dtso
new file mode 100644
index 000000000000..2542abe59d34
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/shikra-iqs-evk-dlc-panel.dtso
@@ -0,0 +1,78 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+&{/} {
+	model = "Qualcomm Technologies, Inc. Shikra IQS EVK DLC Panel";
+
+	backlight: backlight {
+		compatible = "gpio-backlight";
+		gpios = <&pm8150_gpios 1 GPIO_ACTIVE_HIGH>;
+		default-on;
+	};
+};
+
+&hdmi_bridge {
+	status = "disabled";
+};
+
+&hdmi_connector {
+	status = "disabled";
+};
+
+&mdss_dsi0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	panel@0 {
+		compatible = "dlc,dlc0697", "ilitek,ili7807s";
+		reg = <0>;
+		backlight = <&backlight>;
+		reset-gpios = <&tlmm 3 GPIO_ACTIVE_LOW>;
+		vddi-supply = <&pm8150_l15>;
+		avdd-supply = <&vreg_disp_3p3>;
+		avee-supply = <&vreg_disp_3p3>;
+		pinctrl-0 = <&panel_rst_n &panel_te_pin>;
+		pinctrl-1 = <&panel_rst_n_suspend>;
+		pinctrl-names = "default", "sleep";
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&mdss_dsi0_out>;
+			};
+		};
+	};
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&panel_in>;
+};
+
+&tlmm {
+	panel_rst_n: panel-rst-n-state {
+		pins = "gpio3";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	panel_rst_n_suspend: panel-rst-n-suspend-state {
+		pins = "gpio3";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	panel_te_pin: panel-te-pin-state {
+		pins = "gpio86";
+		function = "mdp_vsync_p";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+};

-- 
2.34.1

[PATCH 3/7] arm64: dts: qcom: shikra-iqs-evk: Add AUO G133HAN01 LVDS panel overlay

[vishnu.saini]

From: Anand Tiwari <anand.tiwari@oss.qualcomm.com>

Add a DT overlay for IQS, to enable LVDS interface when LVDS daughter card
is connected to PDISP1 DSI0 on carrier card.
There is SN65DSI84 DSI-to-LVDS bridge on the daughter card which is
connected through I2C3 with reset and interrupt connected to tlmm GPIO76
and GPIO85.
Backlight is connected to gpio87 with pdm_pwm functionality. Currently this
is not supported in linux-next yet, so pull the gpio high.
Enable support for AUO G133HAN01 LVDS panel connected to this daughter card
and disable the default HDMI bridge and connector in favour of the LVDS
panel.

Signed-off-by: Anand Tiwari <anand.tiwari@oss.qualcomm.com>
Signed-off-by: Vishnu Saini <vishnu.saini@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/Makefile                  |   2 +
 .../qcom/shikra-iqs-evk-lvds-auo,g133han01.dtso    | 127 +++++++++++++++++++++
 2 files changed, 129 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 0c5a7b7f694b..610fe640471b 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -381,10 +381,12 @@ dtb-$(CONFIG_ARCH_QCOM)	+= shikra-iqs-evk-imx577-camera.dtb
 shikra-cqm-evk-hdmi-dtbs	:= shikra-cqm-evk.dtb shikra-cqm-cqs-evk-hdmi.dtbo
 shikra-cqs-evk-hdmi-dtbs	:= shikra-cqs-evk.dtb shikra-cqm-cqs-evk-hdmi.dtbo
 shikra-iqs-evk-dlc-panel-dtbs	:= shikra-iqs-evk.dtb shikra-iqs-evk-dlc-panel.dtbo
+shikra-iqs-evk-lvds-auo,g133han01-dtbs	:= shikra-iqs-evk.dtb shikra-iqs-evk-lvds-auo,g133han01.dtbo
 
 dtb-$(CONFIG_ARCH_QCOM)	+= shikra-cqm-evk-hdmi.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= shikra-cqs-evk-hdmi.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= shikra-iqs-evk-dlc-panel.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= shikra-iqs-evk-lvds-auo,g133han01.dtb
 
 dtb-$(CONFIG_ARCH_QCOM)	+= sm4250-oneplus-billie2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm4450-qrd.dtb
diff --git a/arch/arm64/boot/dts/qcom/shikra-iqs-evk-lvds-auo,g133han01.dtso b/arch/arm64/boot/dts/qcom/shikra-iqs-evk-lvds-auo,g133han01.dtso
new file mode 100644
index 000000000000..80b9dcc92061
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/shikra-iqs-evk-lvds-auo,g133han01.dtso
@@ -0,0 +1,127 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+&{/} {
+	backlight {
+		compatible = "gpio-backlight";
+		gpios = <&pm8150_gpios 1 GPIO_ACTIVE_HIGH>;
+		default-on;
+		pinctrl-0 = <&backlight_pwm>;
+		pinctrl-names = "default";
+	};
+
+	panel-lvds {
+		compatible = "auo,g133han01";
+		power-supply = <&vreg_lvds_3p3>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				dual-lvds-odd-pixels;
+
+				lvds_panel_out_a: endpoint {
+					remote-endpoint = <&sn65dsi84_out_a>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				dual-lvds-even-pixels;
+
+				lvds_panel_out_b: endpoint {
+					remote-endpoint = <&sn65dsi84_out_b>;
+				};
+			};
+		};
+	};
+
+	vreg_bridge_1p8: regulator-bridge-1p8 {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_bridge_1p8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vreg_lvds_3p3: regulator-lvds-3p3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_lvds_3p3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&hdmi_bridge {
+	status = "disabled";
+};
+
+&hdmi_connector {
+	status = "disabled";
+};
+
+&i2c3 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bridge@2c {
+		compatible = "ti,sn65dsi84";
+		reg = <0x2c>;
+		enable-gpios = <&tlmm 76 GPIO_ACTIVE_HIGH>;
+		interrupts-extended = <&tlmm 85 IRQ_TYPE_EDGE_FALLING>;
+		vcc-supply = <&vreg_bridge_1p8>;
+		pinctrl-0 = <&bridge_irq_pin &bridge_rst_pin>;
+		pinctrl-names = "default";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				sn65dsi84_in: endpoint {
+					remote-endpoint = <&mdss_dsi0_out>;
+					data-lanes = <1 2 3 4>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				sn65dsi84_out_a: endpoint {
+					remote-endpoint = <&lvds_panel_out_a>;
+				};
+			};
+
+			port@3 {
+				reg = <3>;
+
+				sn65dsi84_out_b: endpoint {
+					remote-endpoint = <&lvds_panel_out_b>;
+				};
+			};
+		};
+	};
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&sn65dsi84_in>;
+};
+
+&tlmm {
+	backlight_pwm: backlight-pwm-state {
+		pins = "gpio87";
+		function = "gpio";
+		bias-pull-up;
+	};
+};

-- 
2.34.1

[PATCH 4/7] arm64: defconfig: Enable RPi touchscreen V2 regulator and ILI9881C panel

[Vishnu Saini]

Enable the regulator driver for the Raspberry Pi touchscreen V2 power
and backlight controller, and the Ilitek ILI9881C DSI panel driver, as
modules, for the Raspberry Pi 7 inch DSI panel on the 22-pin JDISP1 DSI0
connector on Qualcomm Shikra EVK, Talos Lyra EVK boards.

Signed-off-by: Vishnu Saini <vishnu.saini@oss.qualcomm.com>
---
 arch/arm64/configs/defconfig | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index d18f72e55330..9c4c47a44af9 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -900,6 +900,7 @@ CONFIG_REGULATOR_QCOM_SMD_RPM=y
 CONFIG_REGULATOR_QCOM_SPMI=y
 CONFIG_REGULATOR_QCOM_USB_VBUS=m
 CONFIG_REGULATOR_RAA215300=y
+CONFIG_REGULATOR_RASPBERRYPI_TOUCHSCREEN_V2=m
 CONFIG_REGULATOR_RK808=y
 CONFIG_REGULATOR_S2MPS11=y
 CONFIG_REGULATOR_SGM3804=y
@@ -1029,6 +1030,7 @@ CONFIG_DRM_PANEL_HIMAX_HX83112A=m
 CONFIG_DRM_PANEL_HIMAX_HX83112B=m
 CONFIG_DRM_PANEL_ILITEK_ILI7807S=m
 CONFIG_DRM_PANEL_ILITEK_ILI9806E_SPI=m
+CONFIG_DRM_PANEL_ILITEK_ILI9881C=m
 CONFIG_DRM_PANEL_ILITEK_ILI9882T=m
 CONFIG_DRM_PANEL_KHADAS_TS050=m
 CONFIG_DRM_PANEL_MANTIX_MLAF057WE51=m

-- 
2.34.1

[PATCH 5/7] arm64: dts: qcom: shikra-iqs-evk: Add RPi 7-inch DSI panel overlay

[vishnu.saini]

From: Shashank Maurya <shashank.maurya@oss.qualcomm.com>

Add a DT overlay to enable Raspberry Pi 7-inch DSI panel connected to DSI
22pin on the carrier card.
DSI0 from SOC is routed through MUX which can be selected by DIP switch
S1016.5 ON for enabling this 22-pin JDISP1 DSI0 connector.

Add the regulator and backlight controller at I2C4 address 0x45,
Goodix GT911 touch controller, panel power and reset control, and a
2-lane DSI connection.

Disable the default HDMI bridge and connector in favour of the RPi
DSI panel.

Signed-off-by: Shashank Maurya <shashank.maurya@oss.qualcomm.com>
Signed-off-by: Vishnu Saini <vishnu.saini@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/Makefile                  |  2 +
 .../qcom/shikra-iqs-evk-raspberrypi-dsi-7inch.dtso | 91 ++++++++++++++++++++++
 2 files changed, 93 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 610fe640471b..6d64e7ce197e 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -382,11 +382,13 @@ shikra-cqm-evk-hdmi-dtbs	:= shikra-cqm-evk.dtb shikra-cqm-cqs-evk-hdmi.dtbo
 shikra-cqs-evk-hdmi-dtbs	:= shikra-cqs-evk.dtb shikra-cqm-cqs-evk-hdmi.dtbo
 shikra-iqs-evk-dlc-panel-dtbs	:= shikra-iqs-evk.dtb shikra-iqs-evk-dlc-panel.dtbo
 shikra-iqs-evk-lvds-auo,g133han01-dtbs	:= shikra-iqs-evk.dtb shikra-iqs-evk-lvds-auo,g133han01.dtbo
+shikra-iqs-evk-raspberrypi-dsi-7inch-dtbs	:= shikra-iqs-evk.dtb shikra-iqs-evk-raspberrypi-dsi-7inch.dtbo
 
 dtb-$(CONFIG_ARCH_QCOM)	+= shikra-cqm-evk-hdmi.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= shikra-cqs-evk-hdmi.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= shikra-iqs-evk-dlc-panel.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= shikra-iqs-evk-lvds-auo,g133han01.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= shikra-iqs-evk-raspberrypi-dsi-7inch.dtb
 
 dtb-$(CONFIG_ARCH_QCOM)	+= sm4250-oneplus-billie2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm4450-qrd.dtb
diff --git a/arch/arm64/boot/dts/qcom/shikra-iqs-evk-raspberrypi-dsi-7inch.dtso b/arch/arm64/boot/dts/qcom/shikra-iqs-evk-raspberrypi-dsi-7inch.dtso
new file mode 100644
index 000000000000..383dc5aadcfd
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/shikra-iqs-evk-raspberrypi-dsi-7inch.dtso
@@ -0,0 +1,91 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+&{/} {
+	model = "Qualcomm Technologies, Inc. Shikra IQS EVK Raspberry Pi 7inch DSI Panel";
+
+	display_bl: backlight {
+		compatible = "pwm-backlight";
+		power-supply = <&reg_display>;
+		pwms = <&mcu 0 255 0>;
+	};
+
+	reg_display: regulator-display {
+		compatible = "regulator-fixed";
+		regulator-name = "rpi-display";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_dsi_touch: regulator-dsi-touch {
+		compatible = "regulator-fixed";
+		gpio = <&mcu 1 GPIO_ACTIVE_HIGH>;
+		regulator-name = "rpi-touch";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <50000>;
+		enable-active-high;
+	};
+};
+
+&hdmi_bridge {
+	status = "disabled";
+};
+
+&hdmi_connector {
+	status = "disabled";
+};
+
+&i2c4 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	mcu: gpio@45 {
+		compatible = "raspberrypi,touchscreen-panel-regulator-v2";
+		reg = <0x45>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		#pwm-cells = <3>;
+	};
+
+	touchscreen@5d {
+		compatible = "goodix,gt911";
+		reg = <0x5d>;
+		AVDD28-supply = <&reg_dsi_touch>;
+		touchscreen-size-x = <720>;
+		touchscreen-size-y = <1280>;
+	};
+};
+
+&mdss_dsi0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	panel@0 {
+		compatible = "raspberrypi,dsi-7inch", "ilitek,ili9881c";
+		reg = <0>;
+		reset-gpios = <&mcu 0 GPIO_ACTIVE_LOW>;
+		power-supply = <&reg_display>;
+		iovcc-supply = <&pm8150_s4>;
+		backlight = <&display_bl>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&mdss_dsi0_out>;
+			};
+		};
+	};
+};
+
+&mdss_dsi0_out {
+	data-lanes = <0 1>;
+	remote-endpoint = <&panel_in>;
+};

-- 
2.34.1

[PATCH 6/7] arm64: defconfig: Enable Waveshare DSI panel and touch GPIO drivers

[Vishnu Saini]

Enable the Waveshare DSI touch GPIO/backlight controller driver and the
Jadard JD9365DA-H3 DSI panel driver, as modules, for the Waveshare 8
inch DSI panel on the 22-pin JDISP1 DSI0 connector on the Qualcomm Shikra
EVK, Talos Lyra EVK boards.

Signed-off-by: Vishnu Saini <vishnu.saini@oss.qualcomm.com>
---
 arch/arm64/configs/defconfig | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 9c4c47a44af9..73c07961f655 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -727,6 +727,7 @@ CONFIG_GPIO_SYSCON=y
 CONFIG_GPIO_UNIPHIER=y
 CONFIG_GPIO_VF610=y
 CONFIG_GPIO_VISCONTI=y
+CONFIG_GPIO_WAVESHARE_DSI_TOUCH=m
 CONFIG_GPIO_WCD934X=m
 CONFIG_GPIO_XGENE=y
 CONFIG_GPIO_XGENE_SB=y
@@ -1032,6 +1033,7 @@ CONFIG_DRM_PANEL_ILITEK_ILI7807S=m
 CONFIG_DRM_PANEL_ILITEK_ILI9806E_SPI=m
 CONFIG_DRM_PANEL_ILITEK_ILI9881C=m
 CONFIG_DRM_PANEL_ILITEK_ILI9882T=m
+CONFIG_DRM_PANEL_JADARD_JD9365DA_H3=m
 CONFIG_DRM_PANEL_KHADAS_TS050=m
 CONFIG_DRM_PANEL_MANTIX_MLAF057WE51=m
 CONFIG_DRM_PANEL_NOVATEK_NT36672A=m

-- 
2.34.1

[PATCH 7/7] arm64: dts: qcom: shikra-iqs-evk: Add Waveshare 8-inch DSI panel overlay

[vishnu.saini]

From: Shashank Maurya <shashank.maurya@oss.qualcomm.com>

Add a DT overlay to enable Waveshare 8-inch DSI panel connected to DSI
22pin on the carrier card.
DSI0 from SOC is routed through MUX which can be selected by DIP switch
S1016.5 ON, for enabling this 22-pin JDISP1 DSI0 connector.

Add the JD9365DA-H3 panel, GPIO expander at I2C4 address 0x45 for
panel power, reset and backlight, and the Goodix GT9271 touch
controller.

Disable the default HDMI bridge and connector in favour of the
Waveshare DSI panel.

Signed-off-by: Shashank Maurya <shashank.maurya@oss.qualcomm.com>
Signed-off-by: Vishnu Saini <vishnu.saini@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/Makefile                  |  2 +
 .../qcom/shikra-iqs-evk-waveshare-dsi-8inch.dtso   | 77 ++++++++++++++++++++++
 2 files changed, 79 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 6d64e7ce197e..2d25e3cc81f4 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -383,12 +383,14 @@ shikra-cqs-evk-hdmi-dtbs	:= shikra-cqs-evk.dtb shikra-cqm-cqs-evk-hdmi.dtbo
 shikra-iqs-evk-dlc-panel-dtbs	:= shikra-iqs-evk.dtb shikra-iqs-evk-dlc-panel.dtbo
 shikra-iqs-evk-lvds-auo,g133han01-dtbs	:= shikra-iqs-evk.dtb shikra-iqs-evk-lvds-auo,g133han01.dtbo
 shikra-iqs-evk-raspberrypi-dsi-7inch-dtbs	:= shikra-iqs-evk.dtb shikra-iqs-evk-raspberrypi-dsi-7inch.dtbo
+shikra-iqs-evk-waveshare-dsi-8inch-dtbs	:= shikra-iqs-evk.dtb shikra-iqs-evk-waveshare-dsi-8inch.dtbo
 
 dtb-$(CONFIG_ARCH_QCOM)	+= shikra-cqm-evk-hdmi.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= shikra-cqs-evk-hdmi.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= shikra-iqs-evk-dlc-panel.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= shikra-iqs-evk-lvds-auo,g133han01.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= shikra-iqs-evk-raspberrypi-dsi-7inch.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= shikra-iqs-evk-waveshare-dsi-8inch.dtb
 
 dtb-$(CONFIG_ARCH_QCOM)	+= sm4250-oneplus-billie2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm4450-qrd.dtb
diff --git a/arch/arm64/boot/dts/qcom/shikra-iqs-evk-waveshare-dsi-8inch.dtso b/arch/arm64/boot/dts/qcom/shikra-iqs-evk-waveshare-dsi-8inch.dtso
new file mode 100644
index 000000000000..d0aa115681ff
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/shikra-iqs-evk-waveshare-dsi-8inch.dtso
@@ -0,0 +1,77 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+&{/} {
+	model = "Qualcomm Technologies, Inc. Shikra IQS EVK Waveshare 8inch DSI Panel";
+
+	panel_avdd: regulator-panel-avdd {
+		compatible = "regulator-fixed";
+		regulator-name = "panel-avdd";
+		gpios = <&wsgpio 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	panel_iovcc: regulator-panel-iovcc {
+		compatible = "regulator-fixed";
+		regulator-name = "panel-iovcc";
+		gpios = <&wsgpio 4 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&hdmi_bridge {
+	status = "disabled";
+};
+
+&hdmi_connector {
+	status = "disabled";
+};
+
+&i2c4 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	wsgpio: gpio@45 {
+		compatible = "waveshare,dsi-touch-gpio";
+		reg = <0x45>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	touchscreen@5d {
+		compatible = "goodix,gt9271";
+		reg = <0x5d>;
+		reset-gpios = <&wsgpio 9 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&mdss_dsi0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	panel@0 {
+		compatible = "waveshare,8.0-dsi-touch-a", "jadard,jd9365da-h3";
+		reg = <0>;
+		reset-gpios = <&wsgpio 1 GPIO_ACTIVE_LOW>;
+		vccio-supply = <&panel_iovcc>;
+		vdd-supply = <&panel_avdd>;
+		backlight = <&wsgpio>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&mdss_dsi0_out>;
+			};
+		};
+	};
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&panel_in>;
+};

-- 
2.34.1

Re: [PATCH 1/7] arm64: dts: qcom: shikra-cqm-evk, shikra-cqs-evk: Add HDMI overlay

[Konrad Dybcio]

On 10/21/26 4:21 PM, vishnu.saini@oss.qualcomm.com wrote:
> From: Mohit Dsor <mohit.dsor@oss.qualcomm.com>
> 
> Add a DT overlay for CQM and CQS, to enable HDMI output when LT9611UXD
> DSI-to-HDMI daughter card connected to PDISP1 DSI0 on carrier card.
> LT9611UXD is connected through I2C4, with reset and interrupt connected
> to tlmm GPIO76 and GPIO85.

[...]


> +&mdss_dsi0 {
> +	panel@0 {
> +		status = "disabled";
> +	};
> +};

Please refer to the panel by its label directly

Konrad

Re: [PATCH 0/7] arm64: dts: qcom: shikra: Add display overlays for EVK boards

[Konrad Dybcio]

On 10/21/26 4:21 PM, vishnu.saini@oss.qualcomm.com wrote:
> Shikra EVK SoC cards (CQS, CQM, and IQS) are mounted on the Lyra carrier
> card. The DSI0 interface from SoC card is routed to either the 22-pin DSI
> connector on carrier card named as JDISP1 DSI0 or to the B2B connector
> named as PDISP1 DSI0, though a MUX which can be selected by a hardware
> DIP switch. There are multiple daughter cards designed that can be
> connected to this PDISP1 DSI0 B2B connector.
> 
> The below B2B display interfaces are enabled by default in base DTB:
> - IQS: DSI-to-HDMI using the LT9611UXD daughter card
> - CQS/CMS: DLC0697 DSI panel using a DLC daughter card

But if they're daughter cards, they should probably be overlays too?

Konrad