[PATCH V4 1/3] mmc: sdhci: Add support for O2 eMMC HS200 mode

[PATCH V4 1/3] mmc: sdhci: Add support for O2 eMMC HS200 mode

[ernest.zhang]

When use eMMC as boot device, the eMMC signaling voltage is tied to 1.8v
fixed output voltage, bios can set o2 sd host controller PCI configuration
register 0x308 bit4 to 1 to let driver skip 3.3v signaling voltage and 
direct use 1.8v singling voltage in eMMC initialize process.

Changes: Check PCIe register 0x308 bit 4 and skip eMMC 3.3v initialization
process if it is set to 1.

Signed-off-by: ernest.zhang <ernest.zhang@bayhubtech.com>
---
 drivers/mmc/host/sdhci-pci-o2micro.c | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/drivers/mmc/host/sdhci-pci-o2micro.c b/drivers/mmc/host/sdhci-pci-o2micro.c
index 555970a..d465751 100644
--- a/drivers/mmc/host/sdhci-pci-o2micro.c
+++ b/drivers/mmc/host/sdhci-pci-o2micro.c
@@ -3,6 +3,7 @@
  *
  * Authors: Peter Guo <peter.guo@bayhubtech.com>
  *          Adam Lee <adam.lee@canonical.com>
+ *          Ernest Zhang <ernest.zhang@bayhubtech.com>
  *
  * This software is licensed under the terms of the GNU General Public
  * License version 2, as published by the Free Software Foundation, and
@@ -39,6 +40,7 @@
 #define O2_SD_MISC_CTRL4	0xFC
 #define O2_SD_TUNING_CTRL	0x300
 #define O2_SD_PLL_SETTING	0x304
+#define O2_SD_MISC_SETTING	0x308
 #define O2_SD_CLK_SETTING	0x328
 #define O2_SD_CAP_REG2		0x330
 #define O2_SD_CAP_REG0		0x334
@@ -184,6 +186,7 @@ int sdhci_pci_o2_probe_slot(struct sdhci_pci_slot *slot)
 	struct sdhci_pci_chip *chip;
 	struct sdhci_host *host;
 	u32 reg;
+	int ret;
 
 	chip = slot->chip;
 	host = slot->host;
@@ -197,6 +200,21 @@ int sdhci_pci_o2_probe_slot(struct sdhci_pci_slot *slot)
 		if (reg & 0x1)
 			host->quirks |= SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12;
 
+		if (chip->pdev->device == PCI_DEVICE_ID_O2_SEABIRD0) {
+			ret = pci_read_config_dword(chip->pdev,
+						    O2_SD_MISC_SETTING, &reg);
+			if (ret)
+				return -EIO;
+			if (reg & (1 << 4)) {
+				pr_info("%s: emmc 1.8v flag is set, force 1.8v signaling voltage\n",
+				     mmc_hostname(host->mmc));
+				host->flags &= ~SDHCI_SIGNALING_330;
+				host->flags |= SDHCI_SIGNALING_180;
+				host->mmc->caps2 |= MMC_CAP2_NO_SD;
+				host->mmc->caps2 |= MMC_CAP2_NO_SDIO;
+			}
+		}
+
 		if (chip->pdev->device != PCI_DEVICE_ID_O2_FUJIN2)
 			break;
 		/* set dll watch dog timer */
-- 
2.7.4

[PATCH V4 2/3] mmc: sdhci: Add support for O2 hardware tuning

[ernest.zhang]

Add hardware tuning function instead of software tuning because O2/Bayhub
SD host controller support hardware tuning.

Changes: Add many functions to execute hardware tuning for eMMC 1.8V HS200
mode, the hardware tuning command and procedure is based on O2/Bayhub 
hardware tuning spec.

Signed-off-by: ernest.zhang <ernest.zhang@bayhubtech.com>
---
 drivers/mmc/host/sdhci-pci-o2micro.c | 193 +++++++++++++++++++++++++++++++++++
 drivers/mmc/host/sdhci.c             |   5 +-
 2 files changed, 197 insertions(+), 1 deletion(-)

diff --git a/drivers/mmc/host/sdhci-pci-o2micro.c b/drivers/mmc/host/sdhci-pci-o2micro.c
index d465751..a918984 100644
--- a/drivers/mmc/host/sdhci-pci-o2micro.c
+++ b/drivers/mmc/host/sdhci-pci-o2micro.c
@@ -17,6 +17,9 @@
  */
 
 #include <linux/pci.h>
+#include <linux/mmc/host.h>
+#include <linux/mmc/mmc.h>
+#include <linux/delay.h>
 
 #include "sdhci.h"
 #include "sdhci-pci.h"
@@ -55,6 +58,194 @@
 
 #define O2_SD_VENDOR_SETTING	0x110
 #define O2_SD_VENDOR_SETTING2	0x1C8
+#define O2_SD_HW_TUNING_DISABLE	BIT(4)
+
+static void sdhci_o2_start_tuning(struct sdhci_host *host)
+{
+	u16 ctrl;
+
+	ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+	ctrl |= SDHCI_CTRL_EXEC_TUNING;
+	sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
+
+	/*
+	 * As per the Host Controller spec v3.00, tuning command
+	 * generates Buffer Read Ready interrupt, so enable that.
+	 *
+	 * Note: The spec clearly says that when tuning sequence
+	 * is being performed, the controller does not generate
+	 * interrupts other than Buffer Read Ready interrupt. But
+	 * to make sure we don't hit a controller bug, we _only_
+	 * enable Buffer Read Ready interrupt here.
+	 */
+	sdhci_writel(host, SDHCI_INT_DATA_AVAIL, SDHCI_INT_ENABLE);
+	sdhci_writel(host, SDHCI_INT_DATA_AVAIL, SDHCI_SIGNAL_ENABLE);
+}
+
+static void sdhci_o2_end_tuning(struct sdhci_host *host)
+{
+	sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
+	sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
+}
+
+static inline bool sdhci_data_line_cmd(struct mmc_command *cmd)
+{
+	return cmd->data || cmd->flags & MMC_RSP_BUSY;
+}
+
+static void sdhci_del_timer(struct sdhci_host *host, struct mmc_request *mrq)
+{
+	if (sdhci_data_line_cmd(mrq->cmd))
+		del_timer(&host->data_timer);
+	else
+		del_timer(&host->timer);
+}
+
+static void sdhci_o2_set_tuning_mode(struct sdhci_host *host)
+{
+	u16 reg;
+
+	/* enable hardware tuning */
+	reg = sdhci_readw(host, O2_SD_VENDOR_SETTING);
+	reg &= ~O2_SD_HW_TUNING_DISABLE;
+	sdhci_writew(host, reg, O2_SD_VENDOR_SETTING);
+}
+
+
+static int sdhci_o2_send_tuning(struct sdhci_host *host, u32 opcode)
+{
+	struct mmc_command cmd = { };
+	struct mmc_data data = { };
+	struct scatterlist sg;
+	struct mmc_request mrq = { };
+	unsigned long flags;
+	u32 b = host->sdma_boundary;
+	int size = 64;
+	u8 *data_buf = kzalloc(size, GFP_KERNEL);
+
+	if (!data_buf)
+		return -ENOMEM;
+
+	cmd.opcode = opcode;
+	cmd.flags = MMC_RSP_PRESENT | MMC_RSP_OPCODE | MMC_RSP_CRC;
+	cmd.mrq = &mrq;
+	cmd.data = NULL;
+	mrq.cmd = &cmd;
+	mrq.data = &data;
+	data.blksz = size;
+	data.blocks = 1;
+	data.flags = MMC_DATA_READ;
+
+	data.timeout_ns = 50 * NSEC_PER_MSEC;
+
+	data.sg = &sg;
+	data.sg_len = 1;
+	sg_init_one(&sg, data_buf, size);
+
+	spin_lock_irqsave(&host->lock, flags);
+
+	sdhci_writew(host, SDHCI_MAKE_BLKSZ(b, 64), SDHCI_BLOCK_SIZE);
+
+	/*
+	 * The tuning block is sent by the card to the host controller.
+	 * So we set the TRNS_READ bit in the Transfer Mode register.
+	 * This also takes care of setting DMA Enable and Multi Block
+	 * Select in the same register to 0.
+	 */
+	sdhci_writew(host, SDHCI_TRNS_READ, SDHCI_TRANSFER_MODE);
+
+	sdhci_send_command(host, &cmd);
+
+	host->cmd = NULL;
+
+	sdhci_del_timer(host, &mrq);
+
+	host->tuning_done = 0;
+
+	mmiowb();
+	spin_unlock_irqrestore(&host->lock, flags);
+
+	/* Wait for Buffer Read Ready interrupt */
+	wait_event_timeout(host->buf_ready_int, (host->tuning_done == 1),
+			   msecs_to_jiffies(50));
+	kfree(data_buf);
+	return 0;
+}
+
+static void sdhci_o2_reset_tuning(struct sdhci_host *host)
+{
+	u16 ctrl;
+
+	ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+	ctrl &= ~SDHCI_CTRL_TUNED_CLK;
+	ctrl &= ~SDHCI_CTRL_EXEC_TUNING;
+	sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
+}
+
+static void __sdhci_o2_execute_tuning(struct sdhci_host *host, u32 opcode)
+{
+	int i;
+
+	sdhci_o2_send_tuning(host, MMC_SEND_TUNING_BLOCK_HS200);
+
+	for (i = 0; i < 150; i++) {
+		u16 ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+
+		if (!(ctrl & SDHCI_CTRL_EXEC_TUNING)) {
+			if (ctrl & SDHCI_CTRL_TUNED_CLK) {
+				host->tuning_done = true;
+				return;
+			}
+			pr_warn("%s: HW tuning failed !\n",
+				   mmc_hostname(host->mmc));
+			break;
+		}
+
+		mdelay(1);
+	}
+
+	pr_info("%s: Tuning failed, falling back to fixed sampling clock\n",
+		mmc_hostname(host->mmc));
+	sdhci_o2_reset_tuning(host);
+}
+
+static int sdhci_o2_execute_tuning(struct mmc_host *mmc, u32 opcode)
+{
+	struct sdhci_host *host = mmc_priv(mmc);
+	int current_bus_width = 0;
+
+	/*
+	 * This handler only implements the eMMC tuning that is specific to
+	 * this controller.  Fall back to the standard method for other TIMING.
+	 */
+	if (host->timing != MMC_TIMING_MMC_HS200)
+		return sdhci_execute_tuning(mmc, opcode);
+
+	if (WARN_ON(opcode != MMC_SEND_TUNING_BLOCK_HS200))
+		return -EINVAL;
+
+	/*
+	 * o2 sdhci host didn't support 8bit emmc tuning
+	 */
+	if (mmc->ios.bus_width == MMC_BUS_WIDTH_8) {
+		current_bus_width = mmc->ios.bus_width;
+		sdhci_set_bus_width(host, MMC_BUS_WIDTH_4);
+	}
+
+	sdhci_o2_set_tuning_mode(host);
+
+	sdhci_o2_start_tuning(host);
+
+	__sdhci_o2_execute_tuning(host, opcode);
+
+	sdhci_o2_end_tuning(host);
+
+	if (current_bus_width == MMC_BUS_WIDTH_8)
+		sdhci_set_bus_width(host, current_bus_width);
+
+	host->flags &= ~SDHCI_HS400_TUNING;
+	return 0;
+}
 
 static void o2_pci_set_baseclk(struct sdhci_pci_chip *chip, u32 value)
 {
@@ -215,6 +406,8 @@ int sdhci_pci_o2_probe_slot(struct sdhci_pci_slot *slot)
 			}
 		}
 
+		host->mmc_host_ops.execute_tuning = sdhci_o2_execute_tuning;
+
 		if (chip->pdev->device != PCI_DEVICE_ID_O2_FUJIN2)
 			break;
 		/* set dll watch dog timer */
diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
index 2ededa7..3bf6117 100644
--- a/drivers/mmc/host/sdhci.c
+++ b/drivers/mmc/host/sdhci.c
@@ -955,7 +955,10 @@ static void sdhci_set_transfer_mode(struct sdhci_host *host,
 	if (data == NULL) {
 		if (host->quirks2 &
 			SDHCI_QUIRK2_CLEAR_TRANSFERMODE_REG_BEFORE_CMD) {
-			sdhci_writew(host, 0x0, SDHCI_TRANSFER_MODE);
+			/* must not clear SDHCI_TRANSFER_MODE when tuning */
+			if (cmd->opcode != MMC_SEND_TUNING_BLOCK_HS200) {
+				sdhci_writew(host, 0x0, SDHCI_TRANSFER_MODE);
+			}
 		} else {
 		/* clear Auto CMD settings for no data CMDs */
 			mode = sdhci_readw(host, SDHCI_TRANSFER_MODE);
-- 
2.7.4

Re: [PATCH V4 2/3] mmc: sdhci: Add support for O2 hardware tuning

[Adrian Hunter]

On 09/03/18 16:04, ernest.zhang wrote:
> Add hardware tuning function instead of software tuning because O2/Bayhub
> SD host controller support hardware tuning.
> 
> Changes: Add many functions to execute hardware tuning for eMMC 1.8V HS200
> mode, the hardware tuning command and procedure is based on O2/Bayhub 
> hardware tuning spec.
> 
> Signed-off-by: ernest.zhang <ernest.zhang@bayhubtech.com>
> ---

This is where the change log should be:

e.g.

Changes in V4:
	<what you changed between the 3rd version and the 4th version>

Changes in V3:
	<what you changed between the 2nd version and the 3rd version>

etc.

>  drivers/mmc/host/sdhci-pci-o2micro.c | 193 +++++++++++++++++++++++++++++++++++
>  drivers/mmc/host/sdhci.c             |   5 +-
>  2 files changed, 197 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/mmc/host/sdhci-pci-o2micro.c b/drivers/mmc/host/sdhci-pci-o2micro.c
> index d465751..a918984 100644
> --- a/drivers/mmc/host/sdhci-pci-o2micro.c
> +++ b/drivers/mmc/host/sdhci-pci-o2micro.c
> @@ -17,6 +17,9 @@
>   */
>  
>  #include <linux/pci.h>
> +#include <linux/mmc/host.h>
> +#include <linux/mmc/mmc.h>
> +#include <linux/delay.h>
>  
>  #include "sdhci.h"
>  #include "sdhci-pci.h"
> @@ -55,6 +58,194 @@
>  
>  #define O2_SD_VENDOR_SETTING	0x110
>  #define O2_SD_VENDOR_SETTING2	0x1C8
> +#define O2_SD_HW_TUNING_DISABLE	BIT(4)
> +
> +static void sdhci_o2_start_tuning(struct sdhci_host *host)
> +{
> +	u16 ctrl;
> +
> +	ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
> +	ctrl |= SDHCI_CTRL_EXEC_TUNING;
> +	sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
> +
> +	/*
> +	 * As per the Host Controller spec v3.00, tuning command
> +	 * generates Buffer Read Ready interrupt, so enable that.
> +	 *
> +	 * Note: The spec clearly says that when tuning sequence
> +	 * is being performed, the controller does not generate
> +	 * interrupts other than Buffer Read Ready interrupt. But
> +	 * to make sure we don't hit a controller bug, we _only_
> +	 * enable Buffer Read Ready interrupt here.
> +	 */
> +	sdhci_writel(host, SDHCI_INT_DATA_AVAIL, SDHCI_INT_ENABLE);
> +	sdhci_writel(host, SDHCI_INT_DATA_AVAIL, SDHCI_SIGNAL_ENABLE);
> +}
> +
> +static void sdhci_o2_end_tuning(struct sdhci_host *host)
> +{
> +	sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
> +	sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
> +}
> +
> +static inline bool sdhci_data_line_cmd(struct mmc_command *cmd)
> +{
> +	return cmd->data || cmd->flags & MMC_RSP_BUSY;
> +}
> +
> +static void sdhci_del_timer(struct sdhci_host *host, struct mmc_request *mrq)
> +{
> +	if (sdhci_data_line_cmd(mrq->cmd))
> +		del_timer(&host->data_timer);
> +	else
> +		del_timer(&host->timer);
> +}
> +
> +static void sdhci_o2_set_tuning_mode(struct sdhci_host *host)
> +{
> +	u16 reg;
> +
> +	/* enable hardware tuning */
> +	reg = sdhci_readw(host, O2_SD_VENDOR_SETTING);
> +	reg &= ~O2_SD_HW_TUNING_DISABLE;
> +	sdhci_writew(host, reg, O2_SD_VENDOR_SETTING);
> +}
> +
> +
> +static int sdhci_o2_send_tuning(struct sdhci_host *host, u32 opcode)
> +{
> +	struct mmc_command cmd = { };
> +	struct mmc_data data = { };
> +	struct scatterlist sg;
> +	struct mmc_request mrq = { };
> +	unsigned long flags;
> +	u32 b = host->sdma_boundary;
> +	int size = 64;
> +	u8 *data_buf = kzalloc(size, GFP_KERNEL);
> +
> +	if (!data_buf)
> +		return -ENOMEM;
> +
> +	cmd.opcode = opcode;
> +	cmd.flags = MMC_RSP_PRESENT | MMC_RSP_OPCODE | MMC_RSP_CRC;
> +	cmd.mrq = &mrq;
> +	cmd.data = NULL;

As previously, please explain why you have cmd.data = NULL but mrq.data = &data

> +	mrq.cmd = &cmd;
> +	mrq.data = &data;
> +	data.blksz = size;
> +	data.blocks = 1;
> +	data.flags = MMC_DATA_READ;
> +
> +	data.timeout_ns = 50 * NSEC_PER_MSEC;
> +
> +	data.sg = &sg;
> +	data.sg_len = 1;
> +	sg_init_one(&sg, data_buf, size);
> +
> +	spin_lock_irqsave(&host->lock, flags);
> +
> +	sdhci_writew(host, SDHCI_MAKE_BLKSZ(b, 64), SDHCI_BLOCK_SIZE);
> +
> +	/*
> +	 * The tuning block is sent by the card to the host controller.
> +	 * So we set the TRNS_READ bit in the Transfer Mode register.
> +	 * This also takes care of setting DMA Enable and Multi Block
> +	 * Select in the same register to 0.
> +	 */
> +	sdhci_writew(host, SDHCI_TRNS_READ, SDHCI_TRANSFER_MODE);
> +
> +	sdhci_send_command(host, &cmd);
> +
> +	host->cmd = NULL;
> +
> +	sdhci_del_timer(host, &mrq);
> +
> +	host->tuning_done = 0;
> +
> +	mmiowb();
> +	spin_unlock_irqrestore(&host->lock, flags);
> +
> +	/* Wait for Buffer Read Ready interrupt */
> +	wait_event_timeout(host->buf_ready_int, (host->tuning_done == 1),
> +			   msecs_to_jiffies(50));
> +	kfree(data_buf);
> +	return 0;
> +}
> +
> +static void sdhci_o2_reset_tuning(struct sdhci_host *host)
> +{
> +	u16 ctrl;
> +
> +	ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
> +	ctrl &= ~SDHCI_CTRL_TUNED_CLK;
> +	ctrl &= ~SDHCI_CTRL_EXEC_TUNING;
> +	sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
> +}
> +
> +static void __sdhci_o2_execute_tuning(struct sdhci_host *host, u32 opcode)
> +{
> +	int i;
> +
> +	sdhci_o2_send_tuning(host, MMC_SEND_TUNING_BLOCK_HS200);
> +
> +	for (i = 0; i < 150; i++) {
> +		u16 ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
> +
> +		if (!(ctrl & SDHCI_CTRL_EXEC_TUNING)) {
> +			if (ctrl & SDHCI_CTRL_TUNED_CLK) {
> +				host->tuning_done = true;
> +				return;
> +			}
> +			pr_warn("%s: HW tuning failed !\n",
> +				   mmc_hostname(host->mmc));
> +			break;
> +		}
> +
> +		mdelay(1);
> +	}
> +
> +	pr_info("%s: Tuning failed, falling back to fixed sampling clock\n",
> +		mmc_hostname(host->mmc));
> +	sdhci_o2_reset_tuning(host);
> +}
> +
> +static int sdhci_o2_execute_tuning(struct mmc_host *mmc, u32 opcode)
> +{
> +	struct sdhci_host *host = mmc_priv(mmc);
> +	int current_bus_width = 0;
> +
> +	/*
> +	 * This handler only implements the eMMC tuning that is specific to
> +	 * this controller.  Fall back to the standard method for other TIMING.
> +	 */
> +	if (host->timing != MMC_TIMING_MMC_HS200)
> +		return sdhci_execute_tuning(mmc, opcode);
> +
> +	if (WARN_ON(opcode != MMC_SEND_TUNING_BLOCK_HS200))
> +		return -EINVAL;
> +
> +	/*
> +	 * o2 sdhci host didn't support 8bit emmc tuning
> +	 */
> +	if (mmc->ios.bus_width == MMC_BUS_WIDTH_8) {
> +		current_bus_width = mmc->ios.bus_width;
> +		sdhci_set_bus_width(host, MMC_BUS_WIDTH_4);
> +	}
> +
> +	sdhci_o2_set_tuning_mode(host);
> +
> +	sdhci_o2_start_tuning(host);
> +
> +	__sdhci_o2_execute_tuning(host, opcode);
> +
> +	sdhci_o2_end_tuning(host);
> +
> +	if (current_bus_width == MMC_BUS_WIDTH_8)
> +		sdhci_set_bus_width(host, current_bus_width);
> +
> +	host->flags &= ~SDHCI_HS400_TUNING;
> +	return 0;
> +}
>  
>  static void o2_pci_set_baseclk(struct sdhci_pci_chip *chip, u32 value)
>  {
> @@ -215,6 +406,8 @@ int sdhci_pci_o2_probe_slot(struct sdhci_pci_slot *slot)
>  			}
>  		}
>  
> +		host->mmc_host_ops.execute_tuning = sdhci_o2_execute_tuning;
> +
>  		if (chip->pdev->device != PCI_DEVICE_ID_O2_FUJIN2)
>  			break;
>  		/* set dll watch dog timer */
> diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
> index 2ededa7..3bf6117 100644
> --- a/drivers/mmc/host/sdhci.c
> +++ b/drivers/mmc/host/sdhci.c
> @@ -955,7 +955,10 @@ static void sdhci_set_transfer_mode(struct sdhci_host *host,
>  	if (data == NULL) {
>  		if (host->quirks2 &
>  			SDHCI_QUIRK2_CLEAR_TRANSFERMODE_REG_BEFORE_CMD) {
> -			sdhci_writew(host, 0x0, SDHCI_TRANSFER_MODE);
> +			/* must not clear SDHCI_TRANSFER_MODE when tuning */
> +			if (cmd->opcode != MMC_SEND_TUNING_BLOCK_HS200) {
> +				sdhci_writew(host, 0x0, SDHCI_TRANSFER_MODE);
> +			}
>  		} else {
>  		/* clear Auto CMD settings for no data CMDs */
>  			mode = sdhci_readw(host, SDHCI_TRANSFER_MODE);
> 

[PATCH V4 3/3] mmc: sdhci: Add MSI interrupt support for O2 SD host

[ernest.zhang]

Add MSI interrupt support if the SD host device can support MSI interrupt.

Changes: Enable MSI interrupt if the MSI capability bit is set in 
capability register.

Signed-off-by: ernest.zhang <ernest.zhang@bayhubtech.com>
---
 drivers/mmc/host/sdhci-pci-o2micro.c | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)

diff --git a/drivers/mmc/host/sdhci-pci-o2micro.c b/drivers/mmc/host/sdhci-pci-o2micro.c
index a918984..7d04f4b 100644
--- a/drivers/mmc/host/sdhci-pci-o2micro.c
+++ b/drivers/mmc/host/sdhci-pci-o2micro.c
@@ -391,6 +391,23 @@ int sdhci_pci_o2_probe_slot(struct sdhci_pci_slot *slot)
 		if (reg & 0x1)
 			host->quirks |= SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12;
 
+#if defined(CONFIG_PCI_MSI)
+		if (pci_find_capability(chip->pdev, PCI_CAP_ID_MSI)) {
+			ret = pci_enable_msi(chip->pdev);
+			if (!ret) {
+				host->irq = chip->pdev->irq;
+				pr_info("%s: use MSI irq, irq=%d\n",
+					mmc_hostname(host->mmc), host->irq);
+			} else {
+				pr_err("%s: enable PCI MSI failed, err=%d\n",
+					mmc_hostname(host->mmc), ret);
+			}
+		} else {
+			pr_info("%s: unsupport msi, use INTx irq\n",
+				mmc_hostname(host->mmc));
+		}
+#endif
+
 		if (chip->pdev->device == PCI_DEVICE_ID_O2_SEABIRD0) {
 			ret = pci_read_config_dword(chip->pdev,
 						    O2_SD_MISC_SETTING, &reg);
-- 
2.7.4

Re: [PATCH V4 3/3] mmc: sdhci: Add MSI interrupt support for O2 SD host

[Adrian Hunter]

On 09/03/18 16:04, ernest.zhang wrote:
> Add MSI interrupt support if the SD host device can support MSI interrupt.
> 
> Changes: Enable MSI interrupt if the MSI capability bit is set in 
> capability register.
> 
> Signed-off-by: ernest.zhang <ernest.zhang@bayhubtech.com>
> ---
>  drivers/mmc/host/sdhci-pci-o2micro.c | 17 +++++++++++++++++
>  1 file changed, 17 insertions(+)
> 
> diff --git a/drivers/mmc/host/sdhci-pci-o2micro.c b/drivers/mmc/host/sdhci-pci-o2micro.c
> index a918984..7d04f4b 100644
> --- a/drivers/mmc/host/sdhci-pci-o2micro.c
> +++ b/drivers/mmc/host/sdhci-pci-o2micro.c
> @@ -391,6 +391,23 @@ int sdhci_pci_o2_probe_slot(struct sdhci_pci_slot *slot)
>  		if (reg & 0x1)
>  			host->quirks |= SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12;
>  
> +#if defined(CONFIG_PCI_MSI)

Do you really need to check CONFIG_PCI_MSI ?

> +		if (pci_find_capability(chip->pdev, PCI_CAP_ID_MSI)) {
> +			ret = pci_enable_msi(chip->pdev);
> +			if (!ret) {
> +				host->irq = chip->pdev->irq;
> +				pr_info("%s: use MSI irq, irq=%d\n",
> +					mmc_hostname(host->mmc), host->irq);
> +			} else {
> +				pr_err("%s: enable PCI MSI failed, err=%d\n",
> +					mmc_hostname(host->mmc), ret);
> +			}
> +		} else {
> +			pr_info("%s: unsupport msi, use INTx irq\n",
> +				mmc_hostname(host->mmc));
> +		}
> +#endif
> +
>  		if (chip->pdev->device == PCI_DEVICE_ID_O2_SEABIRD0) {
>  			ret = pci_read_config_dword(chip->pdev,
>  						    O2_SD_MISC_SETTING, &reg);
> 

Re: [PATCH V4 1/3] mmc: sdhci: Add support for O2 eMMC HS200 mode

[Adrian Hunter]

On 09/03/18 16:04, ernest.zhang wrote:
> When use eMMC as boot device, the eMMC signaling voltage is tied to 1.8v
> fixed output voltage, bios can set o2 sd host controller PCI configuration
> register 0x308 bit4 to 1 to let driver skip 3.3v signaling voltage and 
> direct use 1.8v singling voltage in eMMC initialize process.
> 
> Changes: Check PCIe register 0x308 bit 4 and skip eMMC 3.3v initialization
> process if it is set to 1.
> 
> Signed-off-by: ernest.zhang <ernest.zhang@bayhubtech.com>

Notwithstanding minor formatting comment below:

Acked-by: Adrian Hunter <adrian.hunter@intel.com>

> ---
>  drivers/mmc/host/sdhci-pci-o2micro.c | 18 ++++++++++++++++++
>  1 file changed, 18 insertions(+)
> 
> diff --git a/drivers/mmc/host/sdhci-pci-o2micro.c b/drivers/mmc/host/sdhci-pci-o2micro.c
> index 555970a..d465751 100644
> --- a/drivers/mmc/host/sdhci-pci-o2micro.c
> +++ b/drivers/mmc/host/sdhci-pci-o2micro.c
> @@ -3,6 +3,7 @@
>   *
>   * Authors: Peter Guo <peter.guo@bayhubtech.com>
>   *          Adam Lee <adam.lee@canonical.com>
> + *          Ernest Zhang <ernest.zhang@bayhubtech.com>
>   *
>   * This software is licensed under the terms of the GNU General Public
>   * License version 2, as published by the Free Software Foundation, and
> @@ -39,6 +40,7 @@
>  #define O2_SD_MISC_CTRL4	0xFC
>  #define O2_SD_TUNING_CTRL	0x300
>  #define O2_SD_PLL_SETTING	0x304
> +#define O2_SD_MISC_SETTING	0x308
>  #define O2_SD_CLK_SETTING	0x328
>  #define O2_SD_CAP_REG2		0x330
>  #define O2_SD_CAP_REG0		0x334
> @@ -184,6 +186,7 @@ int sdhci_pci_o2_probe_slot(struct sdhci_pci_slot *slot)
>  	struct sdhci_pci_chip *chip;
>  	struct sdhci_host *host;
>  	u32 reg;
> +	int ret;
>  
>  	chip = slot->chip;
>  	host = slot->host;
> @@ -197,6 +200,21 @@ int sdhci_pci_o2_probe_slot(struct sdhci_pci_slot *slot)
>  		if (reg & 0x1)
>  			host->quirks |= SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12;
>  
> +		if (chip->pdev->device == PCI_DEVICE_ID_O2_SEABIRD0) {
> +			ret = pci_read_config_dword(chip->pdev,
> +						    O2_SD_MISC_SETTING, &reg);
> +			if (ret)
> +				return -EIO;
> +			if (reg & (1 << 4)) {
> +				pr_info("%s: emmc 1.8v flag is set, force 1.8v signaling voltage\n",
> +				     mmc_hostname(host->mmc));

Indenting is a little odd i.e. checkpatch says

CHECK: Alignment should match open parenthesis
#58: FILE: drivers/mmc/host/sdhci-pci-o2micro.c:210:
+                               pr_info("%s: emmc 1.8v flag is set, force
1.8v signaling voltage\n",
+                                    mmc_hostname(host->mmc))

> +				host->flags &= ~SDHCI_SIGNALING_330;
> +				host->flags |= SDHCI_SIGNALING_180;
> +				host->mmc->caps2 |= MMC_CAP2_NO_SD;
> +				host->mmc->caps2 |= MMC_CAP2_NO_SDIO;
> +			}
> +		}
> +
>  		if (chip->pdev->device != PCI_DEVICE_ID_O2_FUJIN2)
>  			break;
>  		/* set dll watch dog timer */
>