mirror of https://lore.kernel.org/linux-amlogic/
 help / color / mirror / Atom feed
From: narmstrong@baylibre.com (Neil Armstrong)
To: linus-amlogic@lists.infradead.org
Subject: [U-Boot] [PATCH v3 u-boot 1/3] usb: host: Add simple of glue driver for DWC3 USB Controllers integration
Date: Thu, 12 Apr 2018 10:08:17 +0200	[thread overview]
Message-ID: <80253c6e-862d-fada-6be2-07500e5a7653@baylibre.com> (raw)
In-Reply-To: <f4963195-8279-a22d-9a9f-6ee6fa740bc7@codethink.co.uk>

On 12/04/2018 10:07, Ben Dooks wrote:
> On 12/04/18 09:05, Neil Armstrong wrote:
>> Hi Jean-Jacques,
>>
>> On 11/04/2018 18:17, Jean-Jacques Hiblot wrote:
>>>
>>>
>>> On 11/04/2018 17:08, Neil Armstrong wrote:
>>>> This is a port of the dwc3-of-simple driver from Linux to enable/deassert
>>>> clock and resets of a simple DWC3 Controller HW glue.
>>>>
>>>> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
>>>> ---
>>>> ?? drivers/usb/host/Kconfig????????? |?? 7 +++
>>>> ?? drivers/usb/host/Makefile???????? |?? 1 +
>>>> ?? drivers/usb/host/dwc3-of-simple.c | 109 ++++++++++++++++++++++++++++++++++++++
>>>> ?? 3 files changed, 117 insertions(+)
>>>> ?? create mode 100644 drivers/usb/host/dwc3-of-simple.c
>>>>
>>>> diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
>>>> index a7249b7..6caa615 100644
>>>> --- a/drivers/usb/host/Kconfig
>>>> +++ b/drivers/usb/host/Kconfig
>>>> @@ -21,6 +21,13 @@ config USB_XHCI_DWC3
>> [...]
>>
>>>> +
>>>> +static int dwc3_of_simple_clk_init(struct udevice *dev,
>>>> +?????????????????? struct dwc3_of_simple *simple)
>>>> +{
>>>> +??? int ret;
>>>> +
>>>> +??? ret = clk_get_bulk(dev, &simple->clks);
>>>> +??? if (ret == -ENOTSUPP)
>>>
>>> Must be ENOSYS instead of ENOTSUPP, otherwise probe fails on platform not using the clk framework
>>
>> You are right, I naively used the same between reset and clock...
>>
>>>
>>> tested-by: Jean-Jacques hiblot <jjhiblot@ti.com>
>>>
>>>> +??????? return 0;
>>>> +??? if (ret)
>>>> +??????? return ret;
>>>> +
>>>> +#if CONFIG_IS_ENABLED(CLK)
>>>> +??? ret = clk_enable_bulk(&simple->clks);
>>>> +??? if (ret) {
>>>> +??????? clk_release_bulk(&simple->clks);
>>>> +??????? return ret;
>>>> +??? }
>>>> +#endif
>>>> +
>>>> +??? return 0;
>>>> +}
> 
> Is the above #if CONFIG_IS_ENABLED(CLK) avoidable?

No unless some changes in clk.h

Neil

> 
>>
>> [...]
>> Thanks,
>> Neil
>>
>> _______________________________________________
>> linux-amlogic mailing list
>> linux-amlogic at lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/linux-amlogic
>>
> 
> 

  reply	other threads:[~2018-04-12  8:08 UTC|newest]

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-04-11 15:07 [PATCH v3 u-boot 0/3] Add USB Support for Amlogic Meson GXL SoCs Neil Armstrong
2018-04-11 15:08 ` [PATCH v3 u-boot 1/3] usb: host: Add simple of glue driver for DWC3 USB Controllers integration Neil Armstrong
2018-04-11 16:17   ` [U-Boot] " Jean-Jacques Hiblot
2018-04-12  8:05     ` Neil Armstrong
2018-04-12  8:07       ` Ben Dooks
2018-04-12  8:08         ` Neil Armstrong [this message]
2018-04-11 15:08 ` [PATCH v3 u-boot 2/3] usb: host: dwc3: Add support for multiple PHYs Neil Armstrong
2018-04-11 15:08 ` [PATCH v3 u-boot 3/3] phy: Add Amlogic Meson USB2 & USB3 Generic PHY drivers Neil Armstrong
2018-04-11 15:20 ` [PATCH v3 u-boot 0/3] Add USB Support for Amlogic Meson GXL SoCs Marek Vasut

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=80253c6e-862d-fada-6be2-07500e5a7653@baylibre.com \
    --to=narmstrong@baylibre.com \
    --cc=linus-amlogic@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®