[PATCH 1/4] serial: bfin_5xx: remove useless gpio handling with hard flow control

[PATCH 1/4] serial: bfin_5xx: remove useless gpio handling with hard flow control

[Mike Frysinger]

From: Sonic Zhang <sonic.zhang@analog.com>

For UARTs that have dedicated hardware flow control support, there will be
no gpios to request/free as they are part of the normal peripheral pins.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 drivers/serial/bfin_5xx.c |   16 +---------------
 1 files changed, 1 insertions(+), 15 deletions(-)

diff --git a/drivers/serial/bfin_5xx.c b/drivers/serial/bfin_5xx.c
index b4a7650..1b7fd62 100644
--- a/drivers/serial/bfin_5xx.c
+++ b/drivers/serial/bfin_5xx.c
@@ -742,15 +742,6 @@ static int bfin_serial_startup(struct uart_port *port)
 			Status interrupt.\n");
 	}
 
-	if (uart->cts_pin >= 0) {
-		gpio_request(uart->cts_pin, DRIVER_NAME);
-		gpio_direction_output(uart->cts_pin, 1);
-	}
-	if (uart->rts_pin >= 0) {
-		gpio_request(uart->rts_pin, DRIVER_NAME);
-		gpio_direction_output(uart->rts_pin, 0);
-	}
-
 	/* CTS RTS PINs are negative assertive. */
 	UART_PUT_MCR(uart, ACTS);
 	UART_SET_IER(uart, EDSSI);
@@ -797,10 +788,6 @@ static void bfin_serial_shutdown(struct uart_port *port)
 		gpio_free(uart->rts_pin);
 #endif
 #ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
-	if (uart->cts_pin >= 0)
-		gpio_free(uart->cts_pin);
-	if (uart->rts_pin >= 0)
-		gpio_free(uart->rts_pin);
 	if (UART_GET_IER(uart) && EDSSI)
 		free_irq(uart->status_irq, uart);
 #endif
@@ -1405,8 +1392,7 @@ static int bfin_serial_remove(struct platform_device *dev)
 			continue;
 		uart_remove_one_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
 		bfin_serial_ports[i].port.dev = NULL;
-#if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
-	defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
+#if defined(CONFIG_SERIAL_BFIN_CTSRTS)
 		gpio_free(bfin_serial_ports[i].cts_pin);
 		gpio_free(bfin_serial_ports[i].rts_pin);
 #endif
-- 
1.6.5.rc1

[PATCH 2/4] serial: bfin_5xx: need to disable DMA TX interrupt too

[Mike Frysinger]

From: Graf Yang <graf.yang@analog.com>

If we don't disable the DMA TX channel, an inopportune timeout will
trigger the interrupt handler and may cause a dead lock with the spin_lock.

Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 drivers/serial/bfin_5xx.c |    2 ++
 1 files changed, 2 insertions(+), 0 deletions(-)

diff --git a/drivers/serial/bfin_5xx.c b/drivers/serial/bfin_5xx.c
index 1b7fd62..663fec1 100644
--- a/drivers/serial/bfin_5xx.c
+++ b/drivers/serial/bfin_5xx.c
@@ -484,6 +484,7 @@ void bfin_serial_rx_dma_timeout(struct bfin_serial_port *uart)
 {
 	int x_pos, pos;
 
+	dma_disable_irq(uart->tx_dma_channel);
 	dma_disable_irq(uart->rx_dma_channel);
 	spin_lock_bh(&uart->port.lock);
 
@@ -517,6 +518,7 @@ void bfin_serial_rx_dma_timeout(struct bfin_serial_port *uart)
 	}
 
 	spin_unlock_bh(&uart->port.lock);
+	dma_enable_irq(uart->tx_dma_channel);
 	dma_enable_irq(uart->rx_dma_channel);
 
 	mod_timer(&(uart->rx_dma_timer), jiffies + DMA_RX_FLUSH_JIFFIES);
-- 
1.6.5.rc1

[PATCH 3/4] serial: bfin_5xx: kgdboc should accept gdb break only when it is active

[Mike Frysinger]

From: Sonic Zhang <sonic.zhang@analog.com>

If we always check for gdb breaks even when it isn't active, we get false
positives on normal code and the system panics.

URL: http://blackfin.uclinux.org/gf/tracker/5277
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 drivers/serial/bfin_5xx.c |    3 ++-
 1 files changed, 2 insertions(+), 1 deletions(-)

diff --git a/drivers/serial/bfin_5xx.c b/drivers/serial/bfin_5xx.c
index 663fec1..67fa057 100644
--- a/drivers/serial/bfin_5xx.c
+++ b/drivers/serial/bfin_5xx.c
@@ -233,7 +233,8 @@ static void bfin_serial_rx_chars(struct bfin_serial_port *uart)
 
 #if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
 	defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
-	if (kgdb_connected && kgdboc_port_line == uart->port.line)
+	if (kgdb_connected && kgdboc_port_line == uart->port.line
+		&& kgdboc_break_enabled)
 		if (ch == 0x3) {/* Ctrl + C */
 			kgdb_breakpoint();
 			return;
-- 
1.6.5.rc1

[PATCH 4/4] serial: bfin_5xx: pull in linux/io.h for ioremap prototypes

[Mike Frysinger]

git-svn-id: svn://localhost/svn/linux-kernel/trunk@7305 526b6c2d-f592-4532-a319-5dd88ccb003d
---
 drivers/serial/bfin_5xx.c |    1 +
 1 files changed, 1 insertions(+), 0 deletions(-)

diff --git a/drivers/serial/bfin_5xx.c b/drivers/serial/bfin_5xx.c
index 67fa057..c969a68 100644
--- a/drivers/serial/bfin_5xx.c
+++ b/drivers/serial/bfin_5xx.c
@@ -14,6 +14,7 @@
 
 #include <linux/module.h>
 #include <linux/ioport.h>
+#include <linux/io.h>
 #include <linux/init.h>
 #include <linux/console.h>
 #include <linux/sysrq.h>
-- 
1.6.5.rc1

[PATCH 1/4] serial: bfin_5xx: remove useless gpio handling with hard flow control

[Mike Frysinger]

From: Sonic Zhang <sonic.zhang@analog.com>

For UARTs that have dedicated hardware flow control support, there will be
no gpios to request/free as they are part of the normal peripheral pins.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 drivers/serial/bfin_5xx.c |   16 +---------------
 1 files changed, 1 insertions(+), 15 deletions(-)

diff --git a/drivers/serial/bfin_5xx.c b/drivers/serial/bfin_5xx.c
index 50abb7e..15843cc 100644
--- a/drivers/serial/bfin_5xx.c
+++ b/drivers/serial/bfin_5xx.c
@@ -746,15 +746,6 @@ static int bfin_serial_startup(struct uart_port *port)
 			Status interrupt.\n");
 	}
 
-	if (uart->cts_pin >= 0) {
-		gpio_request(uart->cts_pin, DRIVER_NAME);
-		gpio_direction_output(uart->cts_pin, 1);
-	}
-	if (uart->rts_pin >= 0) {
-		gpio_request(uart->rts_pin, DRIVER_NAME);
-		gpio_direction_output(uart->rts_pin, 0);
-	}
-
 	/* CTS RTS PINs are negative assertive. */
 	UART_PUT_MCR(uart, ACTS);
 	UART_SET_IER(uart, EDSSI);
@@ -801,10 +792,6 @@ static void bfin_serial_shutdown(struct uart_port *port)
 		gpio_free(uart->rts_pin);
 #endif
 #ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
-	if (uart->cts_pin >= 0)
-		gpio_free(uart->cts_pin);
-	if (uart->rts_pin >= 0)
-		gpio_free(uart->rts_pin);
 	if (UART_GET_IER(uart) && EDSSI)
 		free_irq(uart->status_irq, uart);
 #endif
@@ -1409,8 +1396,7 @@ static int bfin_serial_remove(struct platform_device *dev)
 			continue;
 		uart_remove_one_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
 		bfin_serial_ports[i].port.dev = NULL;
-#if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
-	defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
+#if defined(CONFIG_SERIAL_BFIN_CTSRTS)
 		gpio_free(bfin_serial_ports[i].cts_pin);
 		gpio_free(bfin_serial_ports[i].rts_pin);
 #endif
-- 
1.6.6

[PATCH 2/4] serial: bfin_5xx: need to disable DMA TX interrupt too

[Mike Frysinger]

From: Graf Yang <graf.yang@analog.com>

If we don't disable the DMA TX channel, an inopportune timeout will
trigger the interrupt handler and may cause a dead lock with the spin_lock.

Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 drivers/serial/bfin_5xx.c |    2 ++
 1 files changed, 2 insertions(+), 0 deletions(-)

diff --git a/drivers/serial/bfin_5xx.c b/drivers/serial/bfin_5xx.c
index 15843cc..b5a9b37 100644
--- a/drivers/serial/bfin_5xx.c
+++ b/drivers/serial/bfin_5xx.c
@@ -488,6 +488,7 @@ void bfin_serial_rx_dma_timeout(struct bfin_serial_port *uart)
 {
 	int x_pos, pos;
 
+	dma_disable_irq(uart->tx_dma_channel);
 	dma_disable_irq(uart->rx_dma_channel);
 	spin_lock_bh(&uart->port.lock);
 
@@ -521,6 +522,7 @@ void bfin_serial_rx_dma_timeout(struct bfin_serial_port *uart)
 	}
 
 	spin_unlock_bh(&uart->port.lock);
+	dma_enable_irq(uart->tx_dma_channel);
 	dma_enable_irq(uart->rx_dma_channel);
 
 	mod_timer(&(uart->rx_dma_timer), jiffies + DMA_RX_FLUSH_JIFFIES);
-- 
1.6.6