From: Michal Simek <michal.simek@amd.com>
To: <linux-kernel@vger.kernel.org>, <monstr@monstr.eu>,
<michal.simek@xilinx.com>, <git@xilinx.com>
Cc: Conor Dooley <conor+dt@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Rob Herring <robh@kernel.org>,
"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
<devicetree@vger.kernel.org>,
"moderated list:ARM/ZYNQ ARCHITECTURE"
<linux-arm-kernel@lists.infradead.org>
Subject: [PATCH 06/15] ARM: zynq: Wire smcc with nand/nor memories on zc770 platform
Date: Wed, 11 Dec 2024 13:41:25 +0100 [thread overview]
Message-ID: <12e697975a1d026e811c2f63aa8bbbd0b9ff4f70.1733920873.git.michal.simek@amd.com> (raw)
In-Reply-To: <cover.1733920873.git.michal.simek@amd.com>
Describe nor child flash node under smcc and enable it for xm012 extension
card. And also describe nand flash memory for xm011 card.
Signed-off-by: Michal Simek <michal.simek@amd.com>
---
arch/arm/boot/dts/xilinx/zynq-7000.dtsi | 7 ++++
arch/arm/boot/dts/xilinx/zynq-zc770-xm011.dts | 30 ++++++++++++++++
arch/arm/boot/dts/xilinx/zynq-zc770-xm012.dts | 34 +++++++++++++++++++
3 files changed, 71 insertions(+)
diff --git a/arch/arm/boot/dts/xilinx/zynq-7000.dtsi b/arch/arm/boot/dts/xilinx/zynq-7000.dtsi
index d334b5f75c8e..268647668db2 100644
--- a/arch/arm/boot/dts/xilinx/zynq-7000.dtsi
+++ b/arch/arm/boot/dts/xilinx/zynq-7000.dtsi
@@ -289,12 +289,19 @@ smcc: memory-controller@e000e000 {
0x2 0x0 0xe4000000 0x2000000>; /* SRAM/NOR CS1 region */
#address-cells = <2>;
#size-cells = <1>;
+ interrupt-parent = <&intc>;
+ interrupts = <0 18 4>;
nfc0: nand-controller@0,0 {
compatible = "arm,pl353-nand-r2p1";
reg = <0 0 0x1000000>;
status = "disabled";
};
+ nor0: flash@1,0 {
+ status = "disabled";
+ compatible = "cfi-flash";
+ reg = <1 0 0x2000000>;
+ };
};
sdhci0: mmc@e0100000 {
diff --git a/arch/arm/boot/dts/xilinx/zynq-zc770-xm011.dts b/arch/arm/boot/dts/xilinx/zynq-zc770-xm011.dts
index ba040743e10d..f9a086fe66d3 100644
--- a/arch/arm/boot/dts/xilinx/zynq-zc770-xm011.dts
+++ b/arch/arm/boot/dts/xilinx/zynq-zc770-xm011.dts
@@ -47,6 +47,36 @@ eeprom: eeprom@52 {
};
};
+&nfc0 {
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ nand@0 {
+ reg = <0>;
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ partition@0 {
+ label = "nand-fsbl-uboot";
+ reg = <0x0 0x1000000>;
+ };
+ partition@1000000 {
+ label = "nand-linux";
+ reg = <0x1000000 0x2000000>;
+ };
+ partition@3000000 {
+ label = "nand-rootfs";
+ reg = <0x3000000 0x200000>;
+ };
+ };
+ };
+};
+
+&smcc {
+ status = "okay";
+};
+
&spi0 {
status = "okay";
num-cs = <4>;
diff --git a/arch/arm/boot/dts/xilinx/zynq-zc770-xm012.dts b/arch/arm/boot/dts/xilinx/zynq-zc770-xm012.dts
index d6392d4ece9c..24520e7d3965 100644
--- a/arch/arm/boot/dts/xilinx/zynq-zc770-xm012.dts
+++ b/arch/arm/boot/dts/xilinx/zynq-zc770-xm012.dts
@@ -53,6 +53,40 @@ eeprom1: eeprom@52 {
};
};
+&nor0 {
+ status = "okay";
+ bank-width = <1>;
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ partition@0 {
+ label = "nor-fsbl-uboot";
+ reg = <0x0 0x100000>;
+ };
+ partition@100000 {
+ label = "nor-linux";
+ reg = <0x100000 0x500000>;
+ };
+ partition@600000 {
+ label = "nor-device-tree";
+ reg = <0x600000 0x20000>;
+ };
+ partition@620000 {
+ label = "nor-rootfs";
+ reg = <0x620000 0x5e0000>;
+ };
+ partition@c00000 {
+ label = "nor-bitstream";
+ reg = <0xc00000 0x400000>;
+ };
+ };
+};
+
+&smcc {
+ status = "okay";
+};
+
&spi1 {
status = "okay";
num-cs = <4>;
--
2.43.0
next prev parent reply other threads:[~2024-12-11 12:42 UTC|newest]
Thread overview: 23+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-12-11 12:41 [PATCH 00/15] ARM: zynq: Sync DTs with U-Boot Michal Simek
2024-12-11 12:41 ` [PATCH 01/15] ARM: zynq: Replace 'io-standard' with 'power-source' property Michal Simek
2024-12-11 12:41 ` [PATCH 02/15] ARM: zynq: Remove deprecated device_type property Michal Simek
2024-12-11 12:41 ` [PATCH 03/15] ARM: zynq: DT: List OCM memory for all platforms Michal Simek
2024-12-11 12:41 ` [PATCH 04/15] ARM: zynq: Mark boot-phase-specific device nodes Michal Simek
2024-12-11 12:41 ` [PATCH 05/15] ARM: zynq: Do not define address/size-cells for nand-controller Michal Simek
2024-12-11 12:41 ` Michal Simek [this message]
2024-12-11 12:41 ` [PATCH 07/15] ARM: zynq: Add ethernet phy reset information to DT(zc702) Michal Simek
2024-12-11 13:45 ` Andrew Lunn
2024-12-11 14:04 ` Michal Simek
2024-12-11 14:21 ` Andrew Lunn
2024-12-11 14:37 ` Michal Simek
2024-12-11 12:41 ` [PATCH 08/15] ARM: zynq: Define u-boot bootscrip addr via DT Michal Simek
2024-12-11 12:41 ` [PATCH 09/15] ARM: zynq: Point via nvmem0 alias to eeprom on zc702/zc706 Michal Simek
2024-12-11 12:41 ` [PATCH 10/15] ARM: zynq: Define rtc alias " Michal Simek
2024-12-11 12:41 ` [PATCH 11/15] ARM: zynq: Rename i2c?-gpio to i2c?-gpio-grp Michal Simek
2024-12-11 12:41 ` [PATCH 12/15] ARM: zynq: Fix fpga region DT nodes name Michal Simek
2024-12-11 12:41 ` [PATCH 13/15] ARM: zynq: Enable QSPIs on platforms Michal Simek
2024-12-11 12:41 ` [PATCH 14/15] ARM: zynq: Add sdhci to alias node Michal Simek
2024-12-11 12:41 ` [PATCH 15/15] ARM: zynq: Remove ethernet0 alias from Microzed Michal Simek
2024-12-11 15:54 ` [PATCH 00/15] ARM: zynq: Sync DTs with U-Boot Rob Herring (Arm)
2024-12-12 7:12 ` Michal Simek
2025-01-06 14:52 ` Michal Simek
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=12e697975a1d026e811c2f63aa8bbbd0b9ff4f70.1733920873.git.michal.simek@amd.com \
--to=michal.simek@amd.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=git@xilinx.com \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=michal.simek@xilinx.com \
--cc=monstr@monstr.eu \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®