[PATCH net-next v2 3/7] r8169: adjust the settings about RxConfig

[Hayes Wang <hayeswang@realtek.com>]

Set the init value before reset in probe function. And then just
modify the relative bits and keep the init settings.

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
---
 drivers/net/r8169.c |   54 +++++++++++++++++++++++++++++++++++++++-----------
 1 files changed, 42 insertions(+), 12 deletions(-)

diff --git a/drivers/net/r8169.c b/drivers/net/r8169.c
index a579da0..50bf897 100644
--- a/drivers/net/r8169.c
+++ b/drivers/net/r8169.c
@@ -282,7 +282,6 @@ enum rtl_registers {
 #define	RXCFG_DMA_SHIFT			8
 					/* Unlimited maximum PCI burst. */
 #define	RX_DMA_BURST			(7 << RXCFG_DMA_SHIFT)
-#define RTL_RX_CONFIG_MASK		0xff7e1880u
 
 	RxMissed	= 0x4c,
 	Cfg9346		= 0x50,
@@ -724,8 +723,6 @@ static void rtl8169_down(struct net_device *dev);
 static void rtl8169_rx_clear(struct rtl8169_private *tp);
 static int rtl8169_poll(struct napi_struct *napi, int budget);
 
-static const unsigned int rtl8169_rx_config = RX_FIFO_THRESH | RX_DMA_BURST;
-
 static u32 ocp_read(struct rtl8169_private *tp, u8 mask, u16 reg)
 {
 	void __iomem *ioaddr = tp->mmio_addr;
@@ -3330,6 +3327,42 @@ static void __devinit rtl_init_pll_power_ops(struct rtl8169_private *tp)
 	}
 }
 
+static void rtl_init_rxcfg(struct rtl8169_private *tp)
+{
+	void __iomem *ioaddr = tp->mmio_addr;
+
+	switch (tp->mac_version) {
+	case RTL_GIGA_MAC_VER_01:
+	case RTL_GIGA_MAC_VER_02:
+	case RTL_GIGA_MAC_VER_03:
+	case RTL_GIGA_MAC_VER_04:
+	case RTL_GIGA_MAC_VER_05:
+	case RTL_GIGA_MAC_VER_06:
+	case RTL_GIGA_MAC_VER_10:
+	case RTL_GIGA_MAC_VER_11:
+	case RTL_GIGA_MAC_VER_12:
+	case RTL_GIGA_MAC_VER_13:
+	case RTL_GIGA_MAC_VER_14:
+	case RTL_GIGA_MAC_VER_15:
+	case RTL_GIGA_MAC_VER_16:
+	case RTL_GIGA_MAC_VER_17:
+		RTL_W32(RxConfig, RX_FIFO_THRESH | RX_DMA_BURST);
+		break;
+	case RTL_GIGA_MAC_VER_18:
+	case RTL_GIGA_MAC_VER_19:
+	case RTL_GIGA_MAC_VER_20:
+	case RTL_GIGA_MAC_VER_21:
+	case RTL_GIGA_MAC_VER_22:
+	case RTL_GIGA_MAC_VER_23:
+	case RTL_GIGA_MAC_VER_24:
+		RTL_W32(RxConfig, RX128_INT_EN | RX_MULTI_EN | RX_DMA_BURST);
+		break;
+	default:
+		RTL_W32(RxConfig, RX128_INT_EN | RX_DMA_BURST);
+		break;
+	}
+}
+
 static void rtl8169_init_ring_indexes(struct rtl8169_private *tp)
 {
 	tp->dirty_tx = tp->dirty_rx = tp->cur_tx = tp->cur_rx = 0;
@@ -3457,6 +3490,11 @@ rtl8169_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 	if (!pci_is_pcie(pdev))
 		netif_info(tp, probe, dev, "not PCI Express\n");
 
+	/* Identify chip attached to board */
+	rtl8169_get_mac_version(tp, dev, cfg->default_ver);
+
+	rtl_init_rxcfg(tp);
+
 	RTL_W16(IntrMask, 0x0000);
 
 	rtl_hw_reset(tp);
@@ -3465,9 +3503,6 @@ rtl8169_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 
 	pci_set_master(pdev);
 
-	/* Identify chip attached to board */
-	rtl8169_get_mac_version(tp, dev, cfg->default_ver);
-
 	/*
 	 * Pretend we are using VLANs; This bypasses a nasty bug where
 	 * Interrupts stop flowing on high load on 8110SCd controllers.
@@ -3767,10 +3802,6 @@ static void rtl8169_hw_reset(struct rtl8169_private *tp)
 static void rtl_set_rx_tx_config_registers(struct rtl8169_private *tp)
 {
 	void __iomem *ioaddr = tp->mmio_addr;
-	u32 cfg = rtl8169_rx_config;
-
-	cfg |= (RTL_R32(RxConfig) & RTL_RX_CONFIG_MASK);
-	RTL_W32(RxConfig, cfg);
 
 	/* Set DMA burst size and Interframe Gap Time */
 	RTL_W32(TxConfig, (TX_DMA_BURST << TxDMAShift) |
@@ -5336,8 +5367,7 @@ static void rtl_set_rx_mode(struct net_device *dev)
 
 	spin_lock_irqsave(&tp->lock, flags);
 
-	tmp = rtl8169_rx_config | rx_mode |
-	      (RTL_R32(RxConfig) & RTL_RX_CONFIG_MASK);
+	tmp = RTL_R32(RxConfig) | rx_mode;
 
 	if (tp->mac_version > RTL_GIGA_MAC_VER_06) {
 		u32 data = mc_filter[0];
-- 
1.7.3.2