* [PATCH v8] arm64: dts: qcom: qcs8300-ride: enable WLAN on qcs8300-ride
@ 2026-01-20 7:06 Wei Zhang
2026-01-20 7:44 ` Dmitry Baryshkov
0 siblings, 1 reply; 4+ messages in thread
From: Wei Zhang @ 2026-01-20 7:06 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, Wei Zhang
Enable WLAN on qcs8300-ride by adding a node for the PMU module
of the WCN6855 and assigning its LDO power outputs to the existing
WiFi module.
On the qcs8300-ride platform, the corresponding firmware and BDF
are QCA6698AQ instead of WCN6855, which have been added in the
20250211 release.
Signed-off-by: Wei Zhang <wei.zhang@oss.qualcomm.com>
---
This patch depends on:
- PCIe
https://lore.kernel.org/all/20251128104928.4070050-1-ziyue.zhang@oss.qualcomm.com/
Changes in v8:
- Reordered regulator nodes to maintain alphabetical consistency (Dmitry)
- Place wifi@0 node under existing pcieport0 label
- Link to v7: https://lore.kernel.org/all/20260119090758.2780678-1-wei.zhang@oss.qualcomm.com/
Changes in v7:
- Align regulator node names to match the existing naming style in the dts (Dmitry)
- Link to v6: https://lore.kernel.org/all/20260119080125.2761623-1-wei.zhang@oss.qualcomm.com/
Changes in v6:
- Rebase patches
- Remove unintended 'output-low' from wlan-en-state pinctrl (Konrad)
- Link to v5: https://lore.kernel.org/all/20251113055148.2729943-1-wei.zhang@oss.qualcomm.com/
Changes in v5:
- Rebase patches
- Flip the order of property-n and property-names (Konrad)
- Flip the order of bias and output property (Konrad)
- Link to v4: https://lore.kernel.org/all/20250325075331.1662306-1-quic_stonez@quicinc.com/
Changes in v4:
- Rename the symbol pcieport0 to pcie0_port0 (Konrad)
- Adjust the property order in node pcie0_port0 (Konrad)
- Add to the commit message mentioning FW and BDF used by QCS8300 (Dmitry)
- Specify the calibration data using the correct variant (Dmitry)
- Link to v3: https://lore.kernel.org/all/20250318093350.2682132-1-quic_stonez@quicinc.com/
Changes in v3:
- Complete the nodes property definitions according to DTS binding requirements (Bjorn)
- Link to v2: https://lore.kernel.org/all/20250227065439.1407230-1-quic_stonez@quicinc.com/
Changes in v2:
- Rename the nodes name according to DTS coding style (Konrad & Krzysztof)
- Provide regulator-min/max-microvolt to the regulators (Konrad)
- Link to v1: https://lore.kernel.org/all/20250210062910.3618336-1-quic_stonez@quicinc.com/
---
arch/arm64/boot/dts/qcom/qcs8300-ride.dts | 105 ++++++++++++++++++++++
1 file changed, 105 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/qcs8300-ride.dts b/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
index 68691f7b5f94..864b32503d29 100644
--- a/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
+++ b/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
@@ -24,6 +24,26 @@ chosen {
stdout-path = "serial0:115200n8";
};
+ vreg_conn_1p8: regulator-conn-1p8 {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_conn_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ startup-delay-us = <4000>;
+ enable-active-high;
+ gpio = <&pmm8650au_1_gpios 4 GPIO_ACTIVE_HIGH>;
+ };
+
+ vreg_conn_pa: regulator-conn-pa {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_conn_pa";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ startup-delay-us = <4000>;
+ enable-active-high;
+ gpio = <&pmm8650au_1_gpios 6 GPIO_ACTIVE_HIGH>;
+ };
+
regulator-usb2-vbus {
compatible = "regulator-fixed";
regulator-name = "USB2_VBUS";
@@ -33,6 +53,68 @@ regulator-usb2-vbus {
enable-active-high;
regulator-always-on;
};
+
+ wcn6855-pmu {
+ compatible = "qcom,wcn6855-pmu";
+
+ pinctrl-0 = <&wlan_en_state>;
+ pinctrl-names = "default";
+
+ vddio-supply = <&vreg_conn_pa>;
+ vddaon-supply = <&vreg_conn_1p8>;
+ vddpmu-supply = <&vreg_conn_pa>;
+ vddpmumx-supply = <&vreg_conn_1p8>;
+ vddpmucx-supply = <&vreg_conn_pa>;
+ vddrfa0p95-supply = <&vreg_conn_1p8>;
+ vddrfa1p3-supply = <&vreg_conn_pa>;
+ vddrfa1p9-supply = <&vreg_conn_1p8>;
+ vddpcie1p3-supply = <&vreg_conn_pa>;
+ vddpcie1p9-supply = <&vreg_conn_1p8>;
+
+ wlan-enable-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+ regulators {
+ vreg_pmu_rfa_cmn: ldo0 {
+ regulator-name = "vreg_pmu_rfa_cmn";
+ };
+
+ vreg_pmu_aon_0p59: ldo1 {
+ regulator-name = "vreg_pmu_aon_0p59";
+ };
+
+ vreg_pmu_wlcx_0p8: ldo2 {
+ regulator-name = "vreg_pmu_wlcx_0p8";
+ };
+
+ vreg_pmu_wlmx_0p85: ldo3 {
+ regulator-name = "vreg_pmu_wlmx_0p85";
+ };
+
+ vreg_pmu_btcmx_0p85: ldo4 {
+ regulator-name = "vreg_pmu_btcmx_0p85";
+ };
+
+ vreg_pmu_rfa_0p8: ldo5 {
+ regulator-name = "vreg_pmu_rfa_0p8";
+ };
+
+ vreg_pmu_rfa_1p2: ldo6 {
+ regulator-name = "vreg_pmu_rfa_1p2";
+ };
+
+ vreg_pmu_rfa_1p7: ldo7 {
+ regulator-name = "vreg_pmu_rfa_1p7";
+ };
+
+ vreg_pmu_pcie_0p9: ldo8 {
+ regulator-name = "vreg_pmu_pcie_0p9";
+ };
+
+ vreg_pmu_pcie_1p8: ldo9 {
+ regulator-name = "vreg_pmu_pcie_1p8";
+ };
+ };
+ };
};
&apps_rsc {
@@ -327,6 +409,23 @@ &pcie0 {
&pcieport0 {
reset-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
wake-gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
+
+ wifi@0 {
+ compatible = "pci17cb,1103";
+ reg = <0x10000 0x0 0x0 0x0 0x0>;
+
+ vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+ vddaon-supply = <&vreg_pmu_aon_0p59>;
+ vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+ vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+ vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+ vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+ vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>;
+ vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
+ vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
+
+ qcom,calibration-variant = "QC_QCS8300_Ride";
+ };
};
&pcie0_phy {
@@ -461,6 +560,12 @@ perst-pins {
bias-pull-down;
};
};
+
+ wlan_en_state: wlan-en-state {
+ pins = "gpio54";
+ function = "gpio";
+ bias-pull-up;
+ };
};
&uart7 {
base-commit: 24d479d26b25bce5faea3ddd9fa8f3a6c3129ea7
prerequisite-patch-id: 0e8aad7b8514142fb33c17829386f17c3a55127a
prerequisite-patch-id: e641f09d4139ac77c34757bd08af2db746de3963
prerequisite-patch-id: 4d16e87cf6213d6e25b2c40e2753d4e629778d53
prerequisite-patch-id: 40187dae2c9518a10866104b9fcd5a481ac67d51
prerequisite-patch-id: dd3bdf2aebda74f3603aff24a2c9aaa7f4fd6763
--
2.34.1
^ permalink raw reply [flat|nested] 4+ messages in thread* Re: [PATCH v8] arm64: dts: qcom: qcs8300-ride: enable WLAN on qcs8300-ride
2026-01-20 7:06 [PATCH v8] arm64: dts: qcom: qcs8300-ride: enable WLAN on qcs8300-ride Wei Zhang
@ 2026-01-20 7:44 ` Dmitry Baryshkov
2026-01-21 6:59 ` Wei Zhang (Stone)
0 siblings, 1 reply; 4+ messages in thread
From: Dmitry Baryshkov @ 2026-01-20 7:44 UTC (permalink / raw)
To: Wei Zhang
Cc: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, linux-arm-msm, devicetree, linux-kernel
On Mon, Jan 19, 2026 at 11:06:49PM -0800, Wei Zhang wrote:
> Enable WLAN on qcs8300-ride by adding a node for the PMU module
> of the WCN6855 and assigning its LDO power outputs to the existing
> WiFi module.
>
> On the qcs8300-ride platform, the corresponding firmware and BDF
> are QCA6698AQ instead of WCN6855, which have been added in the
> 20250211 release.
>
> Signed-off-by: Wei Zhang <wei.zhang@oss.qualcomm.com>
> ---
> This patch depends on:
> - PCIe
> https://lore.kernel.org/all/20251128104928.4070050-1-ziyue.zhang@oss.qualcomm.com/
>
> Changes in v8:
> - Reordered regulator nodes to maintain alphabetical consistency (Dmitry)
> - Place wifi@0 node under existing pcieport0 label
> - Link to v7: https://lore.kernel.org/all/20260119090758.2780678-1-wei.zhang@oss.qualcomm.com/
>
> Changes in v7:
> - Align regulator node names to match the existing naming style in the dts (Dmitry)
> - Link to v6: https://lore.kernel.org/all/20260119080125.2761623-1-wei.zhang@oss.qualcomm.com/
>
> Changes in v6:
> - Rebase patches
> - Remove unintended 'output-low' from wlan-en-state pinctrl (Konrad)
> - Link to v5: https://lore.kernel.org/all/20251113055148.2729943-1-wei.zhang@oss.qualcomm.com/
>
> Changes in v5:
> - Rebase patches
> - Flip the order of property-n and property-names (Konrad)
> - Flip the order of bias and output property (Konrad)
> - Link to v4: https://lore.kernel.org/all/20250325075331.1662306-1-quic_stonez@quicinc.com/
>
> Changes in v4:
> - Rename the symbol pcieport0 to pcie0_port0 (Konrad)
> - Adjust the property order in node pcie0_port0 (Konrad)
> - Add to the commit message mentioning FW and BDF used by QCS8300 (Dmitry)
> - Specify the calibration data using the correct variant (Dmitry)
> - Link to v3: https://lore.kernel.org/all/20250318093350.2682132-1-quic_stonez@quicinc.com/
>
> Changes in v3:
> - Complete the nodes property definitions according to DTS binding requirements (Bjorn)
> - Link to v2: https://lore.kernel.org/all/20250227065439.1407230-1-quic_stonez@quicinc.com/
>
> Changes in v2:
> - Rename the nodes name according to DTS coding style (Konrad & Krzysztof)
> - Provide regulator-min/max-microvolt to the regulators (Konrad)
> - Link to v1: https://lore.kernel.org/all/20250210062910.3618336-1-quic_stonez@quicinc.com/
> ---
> arch/arm64/boot/dts/qcom/qcs8300-ride.dts | 105 ++++++++++++++++++++++
> 1 file changed, 105 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/qcs8300-ride.dts b/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
> index 68691f7b5f94..864b32503d29 100644
> --- a/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
> +++ b/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
> @@ -24,6 +24,26 @@ chosen {
> stdout-path = "serial0:115200n8";
> };
>
> + vreg_conn_1p8: regulator-conn-1p8 {
> + compatible = "regulator-fixed";
> + regulator-name = "vreg_conn_1p8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + startup-delay-us = <4000>;
> + enable-active-high;
> + gpio = <&pmm8650au_1_gpios 4 GPIO_ACTIVE_HIGH>;
> + };
> +
> + vreg_conn_pa: regulator-conn-pa {
> + compatible = "regulator-fixed";
> + regulator-name = "vreg_conn_pa";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + startup-delay-us = <4000>;
> + enable-active-high;
> + gpio = <&pmm8650au_1_gpios 6 GPIO_ACTIVE_HIGH>;
> + };
> +
> regulator-usb2-vbus {
> compatible = "regulator-fixed";
> regulator-name = "USB2_VBUS";
> @@ -33,6 +53,68 @@ regulator-usb2-vbus {
> enable-active-high;
> regulator-always-on;
> };
> +
> + wcn6855-pmu {
> + compatible = "qcom,wcn6855-pmu";
> +
> + pinctrl-0 = <&wlan_en_state>;
> + pinctrl-names = "default";
> +
> + vddio-supply = <&vreg_conn_pa>;
> + vddaon-supply = <&vreg_conn_1p8>;
> + vddpmu-supply = <&vreg_conn_pa>;
> + vddpmumx-supply = <&vreg_conn_1p8>;
> + vddpmucx-supply = <&vreg_conn_pa>;
> + vddrfa0p95-supply = <&vreg_conn_1p8>;
How comes that 0.95V pin is powred on by 1.8V? How comes that 1.3V
pin is powered on by 1.8V?
> + vddrfa1p3-supply = <&vreg_conn_pa>;
> + vddrfa1p9-supply = <&vreg_conn_1p8>;
> + vddpcie1p3-supply = <&vreg_conn_pa>;
> + vddpcie1p9-supply = <&vreg_conn_1p8>;
> +
> + wlan-enable-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
> +
--
With best wishes
Dmitry
^ permalink raw reply [flat|nested] 4+ messages in thread* Re: [PATCH v8] arm64: dts: qcom: qcs8300-ride: enable WLAN on qcs8300-ride
2026-01-20 7:44 ` Dmitry Baryshkov
@ 2026-01-21 6:59 ` Wei Zhang (Stone)
2026-01-21 8:24 ` Dmitry Baryshkov
0 siblings, 1 reply; 4+ messages in thread
From: Wei Zhang (Stone) @ 2026-01-21 6:59 UTC (permalink / raw)
To: Dmitry Baryshkov
Cc: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, linux-arm-msm, devicetree, linux-kernel
On 1/20/2026 3:44 PM, Dmitry Baryshkov wrote:
> On Mon, Jan 19, 2026 at 11:06:49PM -0800, Wei Zhang wrote:
>> Enable WLAN on qcs8300-ride by adding a node for the PMU module
>> of the WCN6855 and assigning its LDO power outputs to the existing
>> WiFi module.
>>
>> On the qcs8300-ride platform, the corresponding firmware and BDF
>> are QCA6698AQ instead of WCN6855, which have been added in the
>> 20250211 release.
>>
>> Signed-off-by: Wei Zhang <wei.zhang@oss.qualcomm.com>
>> ---
>> This patch depends on:
>> - PCIe
>> https://lore.kernel.org/all/20251128104928.4070050-1-ziyue.zhang@oss.qualcomm.com/
>>
>> Changes in v8:
>> - Reordered regulator nodes to maintain alphabetical consistency (Dmitry)
>> - Place wifi@0 node under existing pcieport0 label
>> - Link to v7: https://lore.kernel.org/all/20260119090758.2780678-1-wei.zhang@oss.qualcomm.com/
>>
>> Changes in v7:
>> - Align regulator node names to match the existing naming style in the dts (Dmitry)
>> - Link to v6: https://lore.kernel.org/all/20260119080125.2761623-1-wei.zhang@oss.qualcomm.com/
>>
>> Changes in v6:
>> - Rebase patches
>> - Remove unintended 'output-low' from wlan-en-state pinctrl (Konrad)
>> - Link to v5: https://lore.kernel.org/all/20251113055148.2729943-1-wei.zhang@oss.qualcomm.com/
>>
>> Changes in v5:
>> - Rebase patches
>> - Flip the order of property-n and property-names (Konrad)
>> - Flip the order of bias and output property (Konrad)
>> - Link to v4: https://lore.kernel.org/all/20250325075331.1662306-1-quic_stonez@quicinc.com/
>>
>> Changes in v4:
>> - Rename the symbol pcieport0 to pcie0_port0 (Konrad)
>> - Adjust the property order in node pcie0_port0 (Konrad)
>> - Add to the commit message mentioning FW and BDF used by QCS8300 (Dmitry)
>> - Specify the calibration data using the correct variant (Dmitry)
>> - Link to v3: https://lore.kernel.org/all/20250318093350.2682132-1-quic_stonez@quicinc.com/
>>
>> Changes in v3:
>> - Complete the nodes property definitions according to DTS binding requirements (Bjorn)
>> - Link to v2: https://lore.kernel.org/all/20250227065439.1407230-1-quic_stonez@quicinc.com/
>>
>> Changes in v2:
>> - Rename the nodes name according to DTS coding style (Konrad & Krzysztof)
>> - Provide regulator-min/max-microvolt to the regulators (Konrad)
>> - Link to v1: https://lore.kernel.org/all/20250210062910.3618336-1-quic_stonez@quicinc.com/
>> ---
>> arch/arm64/boot/dts/qcom/qcs8300-ride.dts | 105 ++++++++++++++++++++++
>> 1 file changed, 105 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/qcs8300-ride.dts b/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
>> index 68691f7b5f94..864b32503d29 100644
>> --- a/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
>> +++ b/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
>> @@ -24,6 +24,26 @@ chosen {
>> stdout-path = "serial0:115200n8";
>> };
>>
>> + vreg_conn_1p8: regulator-conn-1p8 {
>> + compatible = "regulator-fixed";
>> + regulator-name = "vreg_conn_1p8";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + startup-delay-us = <4000>;
>> + enable-active-high;
>> + gpio = <&pmm8650au_1_gpios 4 GPIO_ACTIVE_HIGH>;
>> + };
>> +
>> + vreg_conn_pa: regulator-conn-pa {
>> + compatible = "regulator-fixed";
>> + regulator-name = "vreg_conn_pa";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + startup-delay-us = <4000>;
>> + enable-active-high;
>> + gpio = <&pmm8650au_1_gpios 6 GPIO_ACTIVE_HIGH>;
>> + };
>> +
>> regulator-usb2-vbus {
>> compatible = "regulator-fixed";
>> regulator-name = "USB2_VBUS";
>> @@ -33,6 +53,68 @@ regulator-usb2-vbus {
>> enable-active-high;
>> regulator-always-on;
>> };
>> +
>> + wcn6855-pmu {
>> + compatible = "qcom,wcn6855-pmu";
>> +
>> + pinctrl-0 = <&wlan_en_state>;
>> + pinctrl-names = "default";
>> +
>> + vddio-supply = <&vreg_conn_pa>;
>> + vddaon-supply = <&vreg_conn_1p8>;
>> + vddpmu-supply = <&vreg_conn_pa>;
>> + vddpmumx-supply = <&vreg_conn_1p8>;
>> + vddpmucx-supply = <&vreg_conn_pa>;
>> + vddrfa0p95-supply = <&vreg_conn_1p8>;
> How comes that 0.95V pin is powred on by 1.8V? How comes that 1.3V
> pin is powered on by 1.8V?
On this platform, all power domains of the WLAN module are enabled
through external buck converters controlled by PMIC GPIO4.
PMIC‑C GPIO_4 is used for DBU3 ENABLE (PWR_CTRL2_VDD_1P8), and it is
also used to enable the core voltages required by the WLAN card (1.95 V,
1.35 V, 1.05 V. etc).
Do we also need to define a regulator for vddrfa1p3-supply,
vddrfa1p9-supply, vddrfa0p95-supply, etc?
>
>> + vddrfa1p3-supply = <&vreg_conn_pa>;
>> + vddrfa1p9-supply = <&vreg_conn_1p8>;
>> + vddpcie1p3-supply = <&vreg_conn_pa>;
>> + vddpcie1p9-supply = <&vreg_conn_1p8>;
>> +
>> + wlan-enable-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
>> +
^ permalink raw reply [flat|nested] 4+ messages in thread* Re: [PATCH v8] arm64: dts: qcom: qcs8300-ride: enable WLAN on qcs8300-ride
2026-01-21 6:59 ` Wei Zhang (Stone)
@ 2026-01-21 8:24 ` Dmitry Baryshkov
0 siblings, 0 replies; 4+ messages in thread
From: Dmitry Baryshkov @ 2026-01-21 8:24 UTC (permalink / raw)
To: Wei Zhang (Stone)
Cc: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, linux-arm-msm, devicetree, linux-kernel
On Wed, 21 Jan 2026 at 08:59, Wei Zhang (Stone)
<wei.zhang@oss.qualcomm.com> wrote:
>
>
> On 1/20/2026 3:44 PM, Dmitry Baryshkov wrote:
> > On Mon, Jan 19, 2026 at 11:06:49PM -0800, Wei Zhang wrote:
> >> Enable WLAN on qcs8300-ride by adding a node for the PMU module
> >> of the WCN6855 and assigning its LDO power outputs to the existing
> >> WiFi module.
> >>
> >> On the qcs8300-ride platform, the corresponding firmware and BDF
> >> are QCA6698AQ instead of WCN6855, which have been added in the
> >> 20250211 release.
> >>
> >> Signed-off-by: Wei Zhang <wei.zhang@oss.qualcomm.com>
> >> ---
> >> This patch depends on:
> >> - PCIe
> >> https://lore.kernel.org/all/20251128104928.4070050-1-ziyue.zhang@oss.qualcomm.com/
> >>
> >> Changes in v8:
> >> - Reordered regulator nodes to maintain alphabetical consistency (Dmitry)
> >> - Place wifi@0 node under existing pcieport0 label
> >> - Link to v7: https://lore.kernel.org/all/20260119090758.2780678-1-wei.zhang@oss.qualcomm.com/
> >>
> >> Changes in v7:
> >> - Align regulator node names to match the existing naming style in the dts (Dmitry)
> >> - Link to v6: https://lore.kernel.org/all/20260119080125.2761623-1-wei.zhang@oss.qualcomm.com/
> >>
> >> Changes in v6:
> >> - Rebase patches
> >> - Remove unintended 'output-low' from wlan-en-state pinctrl (Konrad)
> >> - Link to v5: https://lore.kernel.org/all/20251113055148.2729943-1-wei.zhang@oss.qualcomm.com/
> >>
> >> Changes in v5:
> >> - Rebase patches
> >> - Flip the order of property-n and property-names (Konrad)
> >> - Flip the order of bias and output property (Konrad)
> >> - Link to v4: https://lore.kernel.org/all/20250325075331.1662306-1-quic_stonez@quicinc.com/
> >>
> >> Changes in v4:
> >> - Rename the symbol pcieport0 to pcie0_port0 (Konrad)
> >> - Adjust the property order in node pcie0_port0 (Konrad)
> >> - Add to the commit message mentioning FW and BDF used by QCS8300 (Dmitry)
> >> - Specify the calibration data using the correct variant (Dmitry)
> >> - Link to v3: https://lore.kernel.org/all/20250318093350.2682132-1-quic_stonez@quicinc.com/
> >>
> >> Changes in v3:
> >> - Complete the nodes property definitions according to DTS binding requirements (Bjorn)
> >> - Link to v2: https://lore.kernel.org/all/20250227065439.1407230-1-quic_stonez@quicinc.com/
> >>
> >> Changes in v2:
> >> - Rename the nodes name according to DTS coding style (Konrad & Krzysztof)
> >> - Provide regulator-min/max-microvolt to the regulators (Konrad)
> >> - Link to v1: https://lore.kernel.org/all/20250210062910.3618336-1-quic_stonez@quicinc.com/
> >> ---
> >> arch/arm64/boot/dts/qcom/qcs8300-ride.dts | 105 ++++++++++++++++++++++
> >> 1 file changed, 105 insertions(+)
> >>
> >> diff --git a/arch/arm64/boot/dts/qcom/qcs8300-ride.dts b/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
> >> index 68691f7b5f94..864b32503d29 100644
> >> --- a/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
> >> +++ b/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
> >> @@ -24,6 +24,26 @@ chosen {
> >> stdout-path = "serial0:115200n8";
> >> };
> >>
> >> + vreg_conn_1p8: regulator-conn-1p8 {
> >> + compatible = "regulator-fixed";
> >> + regulator-name = "vreg_conn_1p8";
> >> + regulator-min-microvolt = <1800000>;
> >> + regulator-max-microvolt = <1800000>;
> >> + startup-delay-us = <4000>;
> >> + enable-active-high;
> >> + gpio = <&pmm8650au_1_gpios 4 GPIO_ACTIVE_HIGH>;
> >> + };
> >> +
> >> + vreg_conn_pa: regulator-conn-pa {
> >> + compatible = "regulator-fixed";
> >> + regulator-name = "vreg_conn_pa";
> >> + regulator-min-microvolt = <1800000>;
> >> + regulator-max-microvolt = <1800000>;
> >> + startup-delay-us = <4000>;
> >> + enable-active-high;
> >> + gpio = <&pmm8650au_1_gpios 6 GPIO_ACTIVE_HIGH>;
> >> + };
> >> +
> >> regulator-usb2-vbus {
> >> compatible = "regulator-fixed";
> >> regulator-name = "USB2_VBUS";
> >> @@ -33,6 +53,68 @@ regulator-usb2-vbus {
> >> enable-active-high;
> >> regulator-always-on;
> >> };
> >> +
> >> + wcn6855-pmu {
> >> + compatible = "qcom,wcn6855-pmu";
> >> +
> >> + pinctrl-0 = <&wlan_en_state>;
> >> + pinctrl-names = "default";
> >> +
> >> + vddio-supply = <&vreg_conn_pa>;
> >> + vddaon-supply = <&vreg_conn_1p8>;
> >> + vddpmu-supply = <&vreg_conn_pa>;
> >> + vddpmumx-supply = <&vreg_conn_1p8>;
> >> + vddpmucx-supply = <&vreg_conn_pa>;
> >> + vddrfa0p95-supply = <&vreg_conn_1p8>;
> > How comes that 0.95V pin is powred on by 1.8V? How comes that 1.3V
> > pin is powered on by 1.8V?
> On this platform, all power domains of the WLAN module are enabled
> through external buck converters controlled by PMIC GPIO4.
> PMIC‑C GPIO_4 is used for DBU3 ENABLE (PWR_CTRL2_VDD_1P8), and it is
> also used to enable the core voltages required by the WLAN card (1.95 V,
> 1.35 V, 1.05 V. etc).
> Do we also need to define a regulator for vddrfa1p3-supply,
> vddrfa1p9-supply, vddrfa0p95-supply, etc?
Could you please describe the hardware. Accurately. Not by using
clumsy shortcuts or incorrect simplifications.
> >
> >> + vddrfa1p3-supply = <&vreg_conn_pa>;
> >> + vddrfa1p9-supply = <&vreg_conn_1p8>;
> >> + vddpcie1p3-supply = <&vreg_conn_pa>;
> >> + vddpcie1p9-supply = <&vreg_conn_1p8>;
> >> +
> >> + wlan-enable-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
> >> +
--
With best wishes
Dmitry
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2026-01-21 8:25 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2026-01-20 7:06 [PATCH v8] arm64: dts: qcom: qcs8300-ride: enable WLAN on qcs8300-ride Wei Zhang
2026-01-20 7:44 ` Dmitry Baryshkov
2026-01-21 6:59 ` Wei Zhang (Stone)
2026-01-21 8:24 ` Dmitry Baryshkov
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®