mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Ludovic Barre <ludovic.Barre@st.com>
To: Ulf Hansson <ulf.hansson@linaro.org>, Rob Herring <robh+dt@kernel.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>,
	Alexandre Torgue <alexandre.torgue@st.com>,
	Gerald Baeza <gerald.baeza@st.com>,
	<linux-arm-kernel@lists.infradead.org>,
	<linux-kernel@vger.kernel.org>, <devicetree@vger.kernel.org>,
	<linux-mmc@vger.kernel.org>, Ludovic Barre <ludovic.barre@st.com>
Subject: [PATCH 10/19] mmc: mmci: add variant property to allow remain data
Date: Tue, 12 Jun 2018 15:14:31 +0200	[thread overview]
Message-ID: <1528809280-31116-11-git-send-email-ludovic.Barre@st.com> (raw)
In-Reply-To: <1528809280-31116-1-git-send-email-ludovic.Barre@st.com>

From: Ludovic Barre <ludovic.barre@st.com>

This patch adds a boolean property to read remaining data.
Needed to support the STM32 sdmmc variant. MMCIDATACNT
register should be read only after the data transfer is complete.
When reading after an error event the read data count value may be
different from the real number of data bytes transferred.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 drivers/mmc/host/mmci.c | 17 +++++++++++++++--
 drivers/mmc/host/mmci.h |  3 +++
 2 files changed, 18 insertions(+), 2 deletions(-)

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 83c3572..abddad7 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -58,6 +58,7 @@ static struct variant_data variant_arm = {
 	.datalength_bits	= 16,
 	.datactrl_blocksz	= 11,
 	.datactrl_dpsm_enable	= MCI_DPSM_ENABLE,
+	.datacnt_remain		= true,
 	.pwrreg_powerup		= MCI_PWR_UP,
 	.f_max			= 100000000,
 	.reversed_irq_handling	= true,
@@ -78,6 +79,7 @@ static struct variant_data variant_arm_extended_fifo = {
 	.datalength_bits	= 16,
 	.datactrl_blocksz	= 11,
 	.datactrl_dpsm_enable	= MCI_DPSM_ENABLE,
+	.datacnt_remain		= true,
 	.pwrreg_powerup		= MCI_PWR_UP,
 	.f_max			= 100000000,
 	.mmcimask1		= true,
@@ -98,6 +100,7 @@ static struct variant_data variant_arm_extended_fifo_hwfc = {
 	.datalength_bits	= 16,
 	.datactrl_blocksz	= 11,
 	.datactrl_dpsm_enable	= MCI_DPSM_ENABLE,
+	.datacnt_remain		= true,
 	.pwrreg_powerup		= MCI_PWR_UP,
 	.f_max			= 100000000,
 	.mmcimask1		= true,
@@ -120,6 +123,7 @@ static struct variant_data variant_u300 = {
 	.datactrl_blocksz	= 11,
 	.datactrl_dpsm_enable	= MCI_DPSM_ENABLE,
 	.datactrl_mask_sdio	= MCI_DPSM_ST_SDIOEN,
+	.datacnt_remain		= true,
 	.st_sdio			= true,
 	.pwrreg_powerup		= MCI_PWR_ON,
 	.f_max			= 100000000,
@@ -146,6 +150,7 @@ static struct variant_data variant_nomadik = {
 	.datactrl_blocksz	= 11,
 	.datactrl_dpsm_enable	= MCI_DPSM_ENABLE,
 	.datactrl_mask_sdio	= MCI_DPSM_ST_SDIOEN,
+	.datacnt_remain		= true,
 	.st_sdio		= true,
 	.st_clkdiv		= true,
 	.pwrreg_powerup		= MCI_PWR_ON,
@@ -175,6 +180,7 @@ static struct variant_data variant_ux500 = {
 	.datactrl_blocksz	= 11,
 	.datactrl_dpsm_enable	= MCI_DPSM_ENABLE,
 	.datactrl_mask_sdio	= MCI_DPSM_ST_SDIOEN,
+	.datacnt_remain		= true,
 	.st_sdio		= true,
 	.st_clkdiv		= true,
 	.pwrreg_powerup		= MCI_PWR_ON,
@@ -209,6 +215,7 @@ static struct variant_data variant_ux500v2 = {
 	.datactrl_blocksz	= 11,
 	.datactrl_dpsm_enable	= MCI_DPSM_ENABLE,
 	.datactrl_mask_sdio	= MCI_DPSM_ST_SDIOEN,
+	.datacnt_remain		= true,
 	.st_sdio		= true,
 	.st_clkdiv		= true,
 	.blksz_datactrl16	= true,
@@ -244,6 +251,7 @@ static struct variant_data variant_stm32 = {
 	.datactrl_blocksz	= 11,
 	.datactrl_dpsm_enable	= MCI_DPSM_ENABLE,
 	.datactrl_mask_sdio	= MCI_DPSM_ST_SDIOEN,
+	.datacnt_remain		= true,
 	.st_sdio		= true,
 	.st_clkdiv		= true,
 	.pwrreg_powerup		= MCI_PWR_ON,
@@ -270,6 +278,7 @@ static struct variant_data variant_qcom = {
 	.datalength_bits	= 24,
 	.datactrl_blocksz	= 11,
 	.datactrl_dpsm_enable	= MCI_DPSM_ENABLE,
+	.datacnt_remain		= true,
 	.pwrreg_powerup		= MCI_PWR_UP,
 	.f_max			= 208000000,
 	.explicit_mclk_control	= true,
@@ -711,8 +720,12 @@ mmci_data_irq(struct mmci_host *host, struct mmc_data *data,
 		 * can be as much as a FIFO-worth of data ahead.  This
 		 * matters for FIFO overruns only.
 		 */
-		remain = readl(host->base + MMCIDATACNT);
-		success = data->blksz * data->blocks - remain;
+		if (host->variant->datacnt_remain) {
+			remain = readl(host->base + MMCIDATACNT);
+			success = data->blksz * data->blocks - remain;
+		} else {
+			success = 0;
+		}
 
 		dev_dbg(mmc_dev(host->mmc), "MCI ERROR IRQ, status 0x%08x at 0x%08x\n",
 			status_err, success);
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index 5091025..12ee2e6 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -260,6 +260,8 @@ struct mmci_host;
  * @datactrl_blksz: block size in power of two
  * @datactrl_dpsm_enable: enable value for DPSM
  * @datactrl_first: true if data must be setup before send command
+ * @datacnt_remain: true if you could read datacnt register
+ *                  to define remain data
  * @pwrreg_powerup: power up value for MMCIPOWER register
  * @f_max: maximum clk frequency supported by the controller.
  * @signal_direction: input/out direction of bus signals can be indicated
@@ -303,6 +305,7 @@ struct variant_data {
 	unsigned int		datactrl_blocksz;
 	unsigned int		datactrl_dpsm_enable;
 	bool			datactrl_first;
+	bool			datacnt_remain;
 	bool			st_sdio;
 	bool			st_clkdiv;
 	bool			blksz_datactrl16;
-- 
2.7.4


  parent reply	other threads:[~2018-06-12 13:16 UTC|newest]

Thread overview: 41+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-06-12 13:14 [PATCH 00/19] mmc: mmci: add stm32 sdmmc variant Ludovic Barre
2018-06-12 13:14 ` [PATCH 01/19] mmc: mmci: regroup and define dma operations Ludovic Barre
2018-07-05 15:17   ` Ulf Hansson
2018-07-11  9:41     ` Ludovic BARRE
2018-07-11 12:16       ` Ulf Hansson
2018-07-12  9:09         ` Ludovic BARRE
2018-06-12 13:14 ` [PATCH 02/19] mmc: mmci: merge qcom dml feature into mmci dma Ludovic Barre
2018-07-05 15:26   ` Ulf Hansson
2018-07-11 15:19     ` Ludovic BARRE
2018-07-13 11:17       ` Ulf Hansson
2018-07-13 13:08         ` Ludovic BARRE
2018-07-30 15:15           ` Ulf Hansson
2018-06-12 13:14 ` [PATCH 03/19] mmc: mmci: add datactrl block size variant property Ludovic Barre
2018-06-12 13:14 ` [PATCH 04/19] mmc: mmci: expand startbiterr to irqmask and error check Ludovic Barre
2018-06-12 13:14 ` [PATCH 05/19] mmc: mmci: allow to overwrite clock/power procedure to specific variant Ludovic Barre
2018-07-05 13:48   ` Ulf Hansson
2018-07-11 12:19     ` Ludovic BARRE
2018-07-11 12:38       ` Ulf Hansson
2018-06-12 13:14 ` [PATCH 06/19] mmc: mmci: add variant properties to define cpsm & cmdresp bits Ludovic Barre
2018-07-05 14:20   ` Ulf Hansson
2018-06-12 13:14 ` [PATCH 07/19] mmc: mmci: add variant property to define dpsm bit Ludovic Barre
2018-06-12 13:14 ` [PATCH 08/19] mmc: mmci: add variant property to define irq pio mask Ludovic Barre
2018-06-12 13:14 ` [PATCH 09/19] mmc: mmci: add variant property to write datactrl before command Ludovic Barre
2018-06-12 13:14 ` Ludovic Barre [this message]
2018-07-05 13:55   ` [PATCH 10/19] mmc: mmci: add variant property to allow remain data Ulf Hansson
2018-06-12 13:14 ` [PATCH 11/19] mmc: mmci: add variant property to check specific data constraint Ludovic Barre
2018-06-12 13:14 ` [PATCH 12/19] mmc: mmci: add variant property to request a reset Ludovic Barre
2018-06-25 21:23   ` Rob Herring
2018-06-12 13:14 ` [PATCH 13/19] mmc: mmci: send stop cmd if a data command fail Ludovic Barre
2018-07-04 13:37   ` Ulf Hansson
2018-07-11  8:57     ` Ludovic BARRE
2018-06-12 13:14 ` [PATCH 14/19] mmc: mmci: add clock divider for stm32 sdmmc Ludovic Barre
2018-06-12 13:14 ` [PATCH 15/19] mmc: mmci: add stm32 sdmmc registers Ludovic Barre
2018-06-12 13:14 ` [PATCH 16/19] mmc: mmci: add DT bindings for STM32 sdmmc Ludovic Barre
2018-06-25 21:47   ` Rob Herring
2018-06-12 13:14 ` [PATCH 17/19] mmc: mmci: add stm32 sdmmc idma support Ludovic Barre
2018-06-12 13:14 ` [PATCH 18/19] mmc: mmci: add specific clk/pwr procedure for stm32 sdmmc Ludovic Barre
2018-07-05 14:49   ` Ulf Hansson
2018-06-12 13:14 ` [PATCH 19/19] mmc: mmci: add stm32 sdmmc variant Ludovic Barre
2018-06-29 13:51 ` [PATCH 00/19] " Ludovic BARRE
2018-06-29 15:18   ` Ulf Hansson

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1528809280-31116-11-git-send-email-ludovic.Barre@st.com \
    --to=ludovic.barre@st.com \
    --cc=alexandre.torgue@st.com \
    --cc=devicetree@vger.kernel.org \
    --cc=gerald.baeza@st.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mmc@vger.kernel.org \
    --cc=mcoquelin.stm32@gmail.com \
    --cc=robh+dt@kernel.org \
    --cc=ulf.hansson@linaro.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®