mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Rohit Agarwal <quic_rohiagar@quicinc.com>
To: agross@kernel.org, andersson@kernel.org,
	konrad.dybcio@linaro.org, robh+dt@kernel.org,
	krzysztof.kozlowski+dt@linaro.org, conor+dt@kernel.org
Cc: linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org,
	Rohit Agarwal <quic_rohiagar@quicinc.com>
Subject: [PATCH 3/8] arm64: dts: qcom: Add PMIC pm7550ba dtsi
Date: Wed,  2 Aug 2023 15:29:21 +0530	[thread overview]
Message-ID: <1690970366-30982-4-git-send-email-quic_rohiagar@quicinc.com> (raw)
In-Reply-To: <1690970366-30982-1-git-send-email-quic_rohiagar@quicinc.com>

Add dtsi for PMIC pm7550ba found in Qualcomm platforms.

Signed-off-by: Rohit Agarwal <quic_rohiagar@quicinc.com>
---
 arch/arm64/boot/dts/qcom/pm7550ba.dtsi | 70 ++++++++++++++++++++++++++++++++++
 1 file changed, 70 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/pm7550ba.dtsi

diff --git a/arch/arm64/boot/dts/qcom/pm7550ba.dtsi b/arch/arm64/boot/dts/qcom/pm7550ba.dtsi
new file mode 100644
index 0000000..97b28bb
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pm7550ba.dtsi
@@ -0,0 +1,70 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+	thermal-zones {
+		pm7550ba-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pm7550ba_temp>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+
+				trip2 {
+					temperature = <145000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
+&spmi_bus {
+	pm7550ba: pmic@7 {
+		compatible = "qcom,pm7550ba", "qcom,spmi-pmic";
+		reg = <7 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm7550ba_temp: temp-alarm@a00 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0xa00>;
+			interrupts = <0x7 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
+
+		pm7550ba_gpios: gpio@8800 {
+			compatible = "qcom,pm7550ba-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pm7550ba_gpios 0 0 8>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		pm7550ba_eusb2_repeater: phy@fd00 {
+			compatible = "qcom,pm8550b-eusb2-repeater";
+			reg = <0xfd00>;
+			#phy-cells = <0>;
+		};
+	};
+};
-- 
2.7.4


  parent reply	other threads:[~2023-08-02 10:14 UTC|newest]

Thread overview: 27+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-08-02  9:59 [PATCH 0/8] Add pmics supported in Qualcomm's SDX75 platform Rohit Agarwal
2023-08-02  9:59 ` [PATCH 1/8] arm64: dts: qcom: sdx75: Add spmi node Rohit Agarwal
2023-08-02 12:40   ` Konrad Dybcio
2023-08-02 13:07     ` Rohit Agarwal
2023-08-02  9:59 ` [PATCH 2/8] arm64: dts: qcom: Add pinctrl gpio support for pm7250b Rohit Agarwal
2023-08-02 12:41   ` Konrad Dybcio
2023-08-02  9:59 ` Rohit Agarwal [this message]
2023-08-02 12:42   ` [PATCH 3/8] arm64: dts: qcom: Add PMIC pm7550ba dtsi Konrad Dybcio
2023-08-02 13:13     ` Rohit Agarwal
2023-08-02 13:14       ` Konrad Dybcio
2023-08-02 13:19         ` Rohit Agarwal
2023-08-03  5:06         ` Pavan Kondeti
2023-08-04 16:58           ` Konrad Dybcio
2023-08-07  4:41             ` Pavan Kondeti
2023-08-02  9:59 ` [PATCH 4/8] arm64: dts: qcom: Add PMIC pmx75 dtsi Rohit Agarwal
2023-08-02 12:46   ` Konrad Dybcio
2023-08-02 13:13     ` Rohit Agarwal
2023-08-02  9:59 ` [PATCH 5/8] ARM: dts: qcom: sdx65-mtp: Update the pmic used in sdx65 Rohit Agarwal
2023-08-02 12:46   ` Konrad Dybcio
2023-08-02 13:17     ` Rohit Agarwal
2023-08-02  9:59 ` [PATCH 6/8] arm64: dts: qcom: sdx75-idp: Add pmics supported in SDX75 Rohit Agarwal
2023-08-02  9:59 ` [PATCH 7/8] arm64: dts: qcom: sdx75: Add rpmhpd node Rohit Agarwal
2023-08-02 12:48   ` Konrad Dybcio
2023-08-02 13:17     ` Rohit Agarwal
2023-08-02  9:59 ` [PATCH 8/8] arm64: dts: qcom: sdx75-idp: Add regulator nodes Rohit Agarwal
2023-08-02 12:49   ` Konrad Dybcio
2023-08-02 17:57     ` Bjorn Andersson

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1690970366-30982-4-git-send-email-quic_rohiagar@quicinc.com \
    --to=quic_rohiagar@quicinc.com \
    --cc=agross@kernel.org \
    --cc=andersson@kernel.org \
    --cc=conor+dt@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=konrad.dybcio@linaro.org \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®