* cd writer problems with 2.4.5ac17
@ 2001-06-24 1:03 safemode
0 siblings, 0 replies; 2+ messages in thread
From: safemode @ 2001-06-24 1:03 UTC (permalink / raw)
To: linux-kernel
I'm thinking that this is a kernel scsi emu problem rather than a CDR problem
due to the past scsi emulation mails i've seen about previous kernels. I've
been forced to move to 2.4.x because i want to use my promise ata66 ide
controller and the 2.2 promise drivers dont work for it. My CDR is detected
as Vendor: CREATIVE Model: CD-RW RW8438E Rev: FC03 by the ide-scsi
module. Now the problem is, cdrecord is very tempermental with it and it
shouldn't be. Often there are input output errors reading blank media before
writing, these lead to drive lockups that can only be recovered by power
cycling (rebooting). The cdrecord i'm using is version 1.11a04 and i'm
going to try an earlier release to see if it's a cdrecord issue in a bit but
i wanted to get responses from anyone else who may be having these problems
early if it isn't.
Errors: In dmesg this shows up.
scsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, lun 0
Write (10) 00 00 00 00 00 00 00 1f 00
hde: irq timeout: status=0xd0 { Busy }
hde: ATAPI reset complete
I cant get the cdrecord actual error until i reboot, but then when i do it's
random when the error does occur, just that it does after a few uses of the
burner.
on a side note. the kernel really likes to hang up when writing to a cd.
This never used to happen a few kernel releases ago. it slows everything
else down but when the cdr does write a cd, it does so without losing any
fifo buffer.
Any more info needed i'd like to give to figure this out, the thing is,
everytime this happens i have to reboot to use the CDR again. It wont even
detect unless it's power cycled and just unplugging the power cord and
putting it back in doesn't really help because it causes one of my other
drives to flip out. (did that last night.)
^ permalink raw reply [flat|nested] 2+ messages in thread
* Re: cd writer problems with 2.4.5ac17
@ 2001-06-25 4:05 Pavel Roskin
0 siblings, 0 replies; 2+ messages in thread
From: Pavel Roskin @ 2001-06-25 4:05 UTC (permalink / raw)
To: safemode; +Cc: linux-kernel
Hello!
I wrote a CD today under 2.4.5-ac17 on MITSUMI CR-4804TE using SCSI
emulation and cdrecord 1.9. No problems at all.
Another computer is running 2.4.5-ac17 with Promise controller, but I only
have hard drives connected to it. No problems except when ACPI was
enabled.
I understand that your CDR is the first (and maybe the only) device
connected to the Promise controller. Consider connecting it to the onboard
controller if you have one.
What you are describing sounds like a hardware problem. You could try the
old kernel and restore the original confuguration of the system.
If it turns out to be a software problem, I'll appreciate if you locate
the change that caused the problem. Also more details about your hardware
would be useful.
--
Regards,
Pavel Roskin
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2001-06-25 4:04 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2001-06-24 1:03 cd writer problems with 2.4.5ac17 safemode
2001-06-25 4:05 Pavel Roskin
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®