From: Greg KH <gregkh@suse.de>
To: linux-kernel@vger.kernel.org, stable@kernel.org
Cc: stable-review@kernel.org, torvalds@linux-foundation.org,
akpm@linux-foundation.org, alan@lxorguk.ukuu.org.uk,
Benjamin Herrenschmidt <benh@kernel.crashing.org>,
David Laight <David.Laight@ACULAB.COM>,
Peter Zijlstra <a.p.zijlstra@chello.nl>,
Darren Hart <darren.hart@intel.com>
Subject: [067/102] mm/futex: fix futex writes on archs with SW tracking of dirty & young
Date: Wed, 03 Aug 2011 15:01:27 -0700 [thread overview]
Message-ID: <20110803221250.782719100@clark.kroah.org> (raw)
In-Reply-To: <20110803221345.GA10346@kroah.com>
3.0-stable review patch. If anyone has any objections, please let us know.
------------------
From: Benjamin Herrenschmidt <benh@kernel.crashing.org>
commit 2efaca927f5cd7ecd0f1554b8f9b6a9a2c329c03 upstream.
I haven't reproduced it myself but the fail scenario is that on such
machines (notably ARM and some embedded powerpc), if you manage to hit
that futex path on a writable page whose dirty bit has gone from the PTE,
you'll livelock inside the kernel from what I can tell.
It will go in a loop of trying the atomic access, failing, trying gup to
"fix it up", getting succcess from gup, go back to the atomic access,
failing again because dirty wasn't fixed etc...
So I think you essentially hang in the kernel.
The scenario is probably rare'ish because affected architecture are
embedded and tend to not swap much (if at all) so we probably rarely hit
the case where dirty is missing or young is missing, but I think Shan has
a piece of SW that can reliably reproduce it using a shared writable
mapping & fork or something like that.
On archs who use SW tracking of dirty & young, a page without dirty is
effectively mapped read-only and a page without young unaccessible in the
PTE.
Additionally, some architectures might lazily flush the TLB when relaxing
write protection (by doing only a local flush), and expect a fault to
invalidate the stale entry if it's still present on another processor.
The futex code assumes that if the "in_atomic()" access -EFAULT's, it can
"fix it up" by causing get_user_pages() which would then be equivalent to
taking the fault.
However that isn't the case. get_user_pages() will not call
handle_mm_fault() in the case where the PTE seems to have the right
permissions, regardless of the dirty and young state. It will eventually
update those bits ... in the struct page, but not in the PTE.
Additionally, it will not handle the lazy TLB flushing that can be
required by some architectures in the fault case.
Basically, gup is the wrong interface for the job. The patch provides a
more appropriate one which boils down to just calling handle_mm_fault()
since what we are trying to do is simulate a real page fault.
The futex code currently attempts to write to user memory within a
pagefault disabled section, and if that fails, tries to fix it up using
get_user_pages().
This doesn't work on archs where the dirty and young bits are maintained
by software, since they will gate access permission in the TLB, and will
not be updated by gup().
In addition, there's an expectation on some archs that a spurious write
fault triggers a local TLB flush, and that is missing from the picture as
well.
I decided that adding those "features" to gup() would be too much for this
already too complex function, and instead added a new simpler
fixup_user_fault() which is essentially a wrapper around handle_mm_fault()
which the futex code can call.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix some nits Darren saw, fiddle comment layout]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reported-by: Shan Hai <haishan.bai@gmail.com>
Tested-by: Shan Hai <haishan.bai@gmail.com>
Cc: David Laight <David.Laight@ACULAB.COM>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Darren Hart <darren.hart@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
include/linux/mm.h | 2 +
kernel/futex.c | 4 +--
mm/memory.c | 58 ++++++++++++++++++++++++++++++++++++++++++++++++++++-
3 files changed, 61 insertions(+), 3 deletions(-)
--- a/include/linux/mm.h
+++ b/include/linux/mm.h
@@ -985,6 +985,8 @@ int get_user_pages(struct task_struct *t
int get_user_pages_fast(unsigned long start, int nr_pages, int write,
struct page **pages);
struct page *get_dump_page(unsigned long addr);
+extern int fixup_user_fault(struct task_struct *tsk, struct mm_struct *mm,
+ unsigned long address, unsigned int fault_flags);
extern int try_to_release_page(struct page * page, gfp_t gfp_mask);
extern void do_invalidatepage(struct page *page, unsigned long offset);
--- a/kernel/futex.c
+++ b/kernel/futex.c
@@ -355,8 +355,8 @@ static int fault_in_user_writeable(u32 _
int ret;
down_read(&mm->mmap_sem);
- ret = get_user_pages(current, mm, (unsigned long)uaddr,
- 1, 1, 0, NULL, NULL);
+ ret = fixup_user_fault(current, mm, (unsigned long)uaddr,
+ FAULT_FLAG_WRITE);
up_read(&mm->mmap_sem);
return ret < 0 ? ret : 0;
--- a/mm/memory.c
+++ b/mm/memory.c
@@ -1816,7 +1816,63 @@ next_page:
}
EXPORT_SYMBOL(__get_user_pages);
-/**
+/*
+ * fixup_user_fault() - manually resolve a user page fault
+ * @tsk: the task_struct to use for page fault accounting, or
+ * NULL if faults are not to be recorded.
+ * @mm: mm_struct of target mm
+ * @address: user address
+ * @fault_flags:flags to pass down to handle_mm_fault()
+ *
+ * This is meant to be called in the specific scenario where for locking reasons
+ * we try to access user memory in atomic context (within a pagefault_disable()
+ * section), this returns -EFAULT, and we want to resolve the user fault before
+ * trying again.
+ *
+ * Typically this is meant to be used by the futex code.
+ *
+ * The main difference with get_user_pages() is that this function will
+ * unconditionally call handle_mm_fault() which will in turn perform all the
+ * necessary SW fixup of the dirty and young bits in the PTE, while
+ * handle_mm_fault() only guarantees to update these in the struct page.
+ *
+ * This is important for some architectures where those bits also gate the
+ * access permission to the page because they are maintained in software. On
+ * such architectures, gup() will not be enough to make a subsequent access
+ * succeed.
+ *
+ * This should be called with the mm_sem held for read.
+ */
+int fixup_user_fault(struct task_struct *tsk, struct mm_struct *mm,
+ unsigned long address, unsigned int fault_flags)
+{
+ struct vm_area_struct *vma;
+ int ret;
+
+ vma = find_extend_vma(mm, address);
+ if (!vma || address < vma->vm_start)
+ return -EFAULT;
+
+ ret = handle_mm_fault(mm, vma, address, fault_flags);
+ if (ret & VM_FAULT_ERROR) {
+ if (ret & VM_FAULT_OOM)
+ return -ENOMEM;
+ if (ret & (VM_FAULT_HWPOISON | VM_FAULT_HWPOISON_LARGE))
+ return -EHWPOISON;
+ if (ret & VM_FAULT_SIGBUS)
+ return -EFAULT;
+ BUG();
+ }
+ if (tsk) {
+ if (ret & VM_FAULT_MAJOR)
+ tsk->maj_flt++;
+ else
+ tsk->min_flt++;
+ }
+ return 0;
+}
+
+/*
* get_user_pages() - pin user pages in memory
* @tsk: the task_struct to use for page fault accounting, or
* NULL if faults are not to be recorded.
next prev parent reply other threads:[~2011-08-03 23:29 UTC|newest]
Thread overview: 103+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-08-03 22:13 [000/102] 3.0.1-stable review Greg KH
2011-08-03 22:00 ` [001/102] USB: serial: add IDs for WinChipHead USB->RS232 adapter Greg KH
2011-08-03 22:00 ` [002/102] mmc: Added quirks for Ricoh 1180:e823 lower base clock frequency Greg KH
2011-08-03 22:00 ` [003/102] mmc: sdhci-esdhc-imx: SDHCI_CARD_PRESENT does not get cleared Greg KH
2011-08-03 22:00 ` [004/102] bridge: send proper message_age in config BPDU Greg KH
2011-08-03 22:00 ` [005/102] gro: Only reset frag0 when skb can be pulled Greg KH
2011-08-03 22:00 ` [006/102] Staging: usbip: vhci-hcd: Do not kill already dead RX/TX kthread Greg KH
2011-08-03 22:00 ` [007/102] staging: r8192e_pci: Handle duplicate PCI ID 0x10ec:0x8192 conflict with rtl8192se Greg KH
2011-08-03 22:00 ` [008/102] staging: comedi: fix infoleak to userspace Greg KH
2011-08-03 22:00 ` [009/102] Staging: hv: storvsc: Increase the timeout value in the storvsc driver Greg KH
2011-08-03 22:00 ` [010/102] Staging: hv: vmbus: Increase the timeout value in the vmbus driver Greg KH
2011-08-03 22:00 ` [011/102] Staging: hv: netvsc: Increase the timeout value in the netvsc driver Greg KH
2011-08-03 22:00 ` [012/102] USB: OHCI: fix another regression for NVIDIA controllers Greg KH
2011-08-03 22:00 ` [013/102] USB: EHCI: go back to using the system clock for QH unlinks Greg KH
2011-08-03 22:00 ` [014/102] usb: musb: restore INDEX register in resume path Greg KH
2011-08-03 22:00 ` [015/102] rtc: handle errors correctly in rtc_irq_set_state() Greg KH
2011-08-03 22:00 ` [016/102] rtc: fix hrtimer deadlock Greg KH
2011-08-03 22:00 ` [017/102] rtc: limit frequency Greg KH
2011-08-03 22:00 ` [018/102] drivers/rtc/rtc-tegra.c: properly initialize spinlock Greg KH
2011-08-03 22:00 ` [019/102] ARM: pxa/cm-x300: fix V3020 RTC functionality Greg KH
2011-08-03 22:00 ` [020/102] ASoC: davinci: add missing break statement Greg KH
2011-08-03 22:00 ` [021/102] ASoC: davinci: fix codec start and stop functions Greg KH
2011-08-03 22:00 ` [022/102] ASoC: Mark cache as dirty when suspending Greg KH
2011-08-03 22:00 ` [023/102] ath6kl: cache firmware Greg KH
2011-08-03 22:00 ` [024/102] ath6kl: fix crash when interface is closed but scan is ongoing Greg KH
2011-08-03 22:00 ` [025/102] ath9k_hw: Fix incorrect key_miss handling Greg KH
2011-08-03 22:00 ` [026/102] CIFS: Fix oops while mounting with prefixpath Greg KH
2011-08-03 22:00 ` [027/102] staging: brcm80211: fix for reported log spam problem Greg KH
2011-08-03 22:00 ` [028/102] jme: Fix unmap error (Causing system freeze) Greg KH
2011-08-03 22:00 ` [029/102] ethtool: Allow zero-length register dumps again Greg KH
2011-08-03 22:00 ` [030/102] firewire: cdev: return -ENOTTY for unimplemented ioctls, not -EINVAL Greg KH
2011-08-03 22:00 ` [031/102] firewire: cdev: prevent race between first get_info ioctl and bus reset event queuing Greg KH
2011-08-03 22:00 ` [032/102] IB/srp: Avoid duplicate devices from LUN scan Greg KH
2011-08-03 22:00 ` [033/102] [SCSI] libsas: remove expander from dev list on error Greg KH
2011-08-03 22:00 ` [034/102] rtlwifi: rtl8192cu: Fix duplicate if test Greg KH
2011-08-03 22:00 ` [035/102] mac80211: Restart STA timers only on associated state Greg KH
2011-08-03 22:00 ` [036/102] irq_work, ppc: Fix up arch hooks Greg KH
2011-08-03 22:00 ` [037/102] perf tools, x86: Fix 32-bit compile on 64-bit system Greg KH
2011-08-03 22:00 ` [038/102] perf tools: Fix endian conversion reading event attr from file header Greg KH
2011-08-03 22:00 ` [039/102] x86, intel, power: Initialize MSR_IA32_ENERGY_PERF_BIAS Greg KH
2011-08-03 22:01 ` [040/102] perf: Fix software event overflow Greg KH
2011-08-03 22:01 ` [041/102] [SCSI] Blacklist Traxdata CDR4120 and IOMEGA Zip drive to avoid lock ups Greg KH
2011-08-03 22:01 ` [042/102] [SCSI] sr: check_events() ignore GET_EVENT when TUR says otherwise Greg KH
2011-08-03 22:01 ` [043/102] [SCSI] ses: requesting a fault indication Greg KH
2011-08-03 22:01 ` [044/102] [SCSI] fix crash in scsi_dispatch_cmd() Greg KH
2011-08-03 22:01 ` [045/102] [SCSI] pmcraid: reject negative request size Greg KH
2011-08-03 22:01 ` [046/102] [SCSI] hpsa: do not attempt to read from a write-only register Greg KH
2011-08-03 22:01 ` [047/102] drm/radeon/kms: fix i2c map for rv250/280 Greg KH
2011-08-03 22:01 ` [048/102] drm/radeon/kms: fix DP training for DPEncoderService revision bigger than 1.1 Greg KH
2011-08-03 22:01 ` [049/102] drm/radeon/kms: add missing vddci setting on NI+ Greg KH
2011-08-03 22:01 ` [050/102] ALSA: virtuoso: fix silent analog output on Xonar Essence ST Deluxe Greg KH
2011-08-03 22:01 ` [051/102] ALSA: hda - Fix duplicated DAC assignments for Realtek Greg KH
2011-08-03 22:01 ` [052/102] pnfs: save layoutcommit lwb at layout header Greg KH
2011-08-03 22:01 ` [053/102] pnfs: save layoutcommit cred at layout header init Greg KH
2011-08-03 22:01 ` [054/102] pnfs: let layoutcommit handle a list of lseg Greg KH
2011-08-03 22:01 ` [055/102] pnfs: use lwb as layoutcommit length Greg KH
2011-08-03 22:01 ` [056/102] kexec, x86: Fix incorrect jump back address if not preserving context Greg KH
2011-08-03 22:01 ` [057/102] oprofile, x86: Fix nmi-unsafe callgraph support Greg KH
2011-08-03 22:01 ` [058/102] powerpc/kdump: Fix timeout in crash_kexec_wait_realmode Greg KH
2011-08-03 22:01 ` [059/102] irq_work, alpha: Fix up arch hooks Greg KH
2011-08-03 22:01 ` [060/102] tracing: Fix bug when reading system filters on module removal Greg KH
2011-08-03 22:01 ` [061/102] tracing: Have "enable" file use refcounts like the "filter" file Greg KH
2011-08-03 22:01 ` [062/102] XZ: Fix missing <linux/kernel.h> include Greg KH
2011-08-03 22:01 ` [063/102] PCI: ARI is a PCIe v2 feature Greg KH
2011-08-03 22:01 ` [064/102] cciss: do not attempt to read from a write-only register Greg KH
2011-08-03 22:01 ` [065/102] drivers/firmware/sigma.c needs MODULE_LICENSE Greg KH
2011-08-03 22:01 ` [066/102] geode: reflect mfgpt dependency on mfd Greg KH
2011-08-03 22:01 ` Greg KH [this message]
2011-08-03 22:01 ` [068/102] mm/backing-dev.c: reset bdi min_ratio in bdi_unregister() Greg KH
2011-08-03 22:01 ` [069/102] xtensa: prevent arbitrary read in ptrace Greg KH
2011-08-03 22:01 ` [070/102] ext4: fix i_blocks/quota accounting when extent insertion fails Greg KH
2011-08-03 22:01 ` [071/102] ext4: free allocated and pre-allocated blocks when check_eofblocks_fl fails Greg KH
2011-08-03 22:01 ` [072/102] ext3: Fix oops in ext3_try_to_allocate_with_rsv() Greg KH
2011-08-03 22:01 ` [073/102] ecryptfs: Make inode bdi consistent with superblock bdi Greg KH
2011-08-03 22:01 ` [074/102] eCryptfs: Unlock keys needed by ecryptfsd Greg KH
2011-08-03 22:01 ` [075/102] nfsd: dont break lease on CLAIM_DELEGATE_CUR Greg KH
2011-08-03 22:01 ` [076/102] nfsd4: remember to put RW access on stateid destruction Greg KH
2011-08-03 22:01 ` [077/102] nfsd4: fix file leak on open_downgrade Greg KH
2011-08-03 22:01 ` [078/102] svcrpc: fix list-corrupting race on nfsd shutdown Greg KH
2011-08-03 22:01 ` [079/102] NFSv4: Dont use the delegation->inode in nfs_mark_return_delegation() Greg KH
2011-08-03 22:01 ` [080/102] NFS: Fix spurious readdir cookie loop messages Greg KH
2011-08-03 22:01 ` [081/102] proc: fix a race in do_io_accounting() Greg KH
2011-08-03 22:01 ` [082/102] n_gsm: fix the wrong FCS handling Greg KH
2011-08-03 22:01 ` [083/102] EHCI: only power off port if over-current is active Greg KH
2011-08-03 22:01 ` [084/102] EHCI: fix direction handling for interrupt data toggles Greg KH
2011-08-03 22:01 ` [085/102] cfg80211: really ignore the regulatory request Greg KH
2011-08-03 22:01 ` [086/102] memcg: fix behavior of mem_cgroup_resize_limit() Greg KH
2011-08-03 22:01 ` [087/102] tty/serial: Fix XSCALE serial ports, e.g. ce4100 Greg KH
2011-08-03 22:01 ` [088/102] SERIAL: SC26xx: Fix link error Greg KH
2011-08-03 22:01 ` [089/102] powerpc/pseries/hvconsole: Fix dropped console output Greg KH
2011-08-03 22:01 ` [090/102] hvc_console: Improve tty/console put_chars handling Greg KH
2011-08-03 22:01 ` [091/102] ipc/sem.c: fix race with concurrent semtimedop() timeouts and IPC_RMID Greg KH
2011-08-03 22:01 ` [092/102] AppArmor: Fix reference to rcu protected pointer outside of rcu_read_lock Greg KH
2011-08-03 22:01 ` [093/102] AppArmor: Fix masking of capabilities in complain mode Greg KH
2011-08-03 22:01 ` [094/102] oom: task->mm == NULL doesnt mean the memory was freed Greg KH
2011-08-03 22:01 ` [095/102] rt2x00: Add device ID for RT539F device Greg KH
2011-08-03 22:01 ` [096/102] GFS2: Fix mount hang caused by certain access pattern to sysfs files Greg KH
2011-08-03 22:01 ` [097/102] watchdog: shwdt: fix usage of mod_timer Greg KH
2011-08-03 22:01 ` [098/102] ALSA: sound/core/pcm_compat.c: adjust array index Greg KH
2011-08-03 22:01 ` [099/102] dm io: flush cpu cache with vmapped io Greg KH
2011-08-03 22:02 ` [100/102] dm snapshot: flush disk cache when merging Greg KH
2011-08-03 22:02 ` [101/102] dm mpath: fix potential NULL pointer in feature arg processing Greg KH
2011-08-03 22:02 ` [102/102] dm: fix idr leak on module removal Greg KH
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20110803221250.782719100@clark.kroah.org \
--to=gregkh@suse.de \
--cc=David.Laight@ACULAB.COM \
--cc=a.p.zijlstra@chello.nl \
--cc=akpm@linux-foundation.org \
--cc=alan@lxorguk.ukuu.org.uk \
--cc=benh@kernel.crashing.org \
--cc=darren.hart@intel.com \
--cc=linux-kernel@vger.kernel.org \
--cc=stable-review@kernel.org \
--cc=stable@kernel.org \
--cc=torvalds@linux-foundation.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®