mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: "Paul E. McKenney" <paulmck@kernel.org>
To: Alan Stern <stern@rowland.harvard.edu>
Cc: Jonas Oberhauser <jonas.oberhauser@huaweicloud.com>,
	Boqun Feng <boqun.feng@gmail.com>,
	Jonas Oberhauser <jonas.oberhauser@huawei.com>,
	parri.andrea@gmail.com, will@kernel.org, peterz@infradead.org,
	npiggin@gmail.com, dhowells@redhat.com, j.alglave@ucl.ac.uk,
	luc.maranget@inria.fr, akiyks@gmail.com, dlustig@nvidia.com,
	joel@joelfernandes.org, urezki@gmail.com,
	quic_neeraju@quicinc.com, frederic@kernel.org,
	linux-kernel@vger.kernel.org
Subject: Re: [PATCH v3] tools/memory-model: Make ppo a subrelation of po
Date: Sun, 26 Feb 2023 10:45:28 -0800	[thread overview]
Message-ID: <20230226184528.GY2948950@paulmck-ThinkPad-P17-Gen-1> (raw)
In-Reply-To: <Y/uOA3umovz06/SV@rowland.harvard.edu>

On Sun, Feb 26, 2023 at 11:51:15AM -0500, Alan Stern wrote:
> On Sun, Feb 26, 2023 at 12:17:31PM +0100, Jonas Oberhauser wrote:
> > On 2/26/2023 4:30 AM, Alan Stern wrote:
> > > On Sat, Feb 25, 2023 at 07:09:05PM -0800, Boqun Feng wrote:
> > > > On Sat, Feb 25, 2023 at 09:29:51PM -0500, Alan Stern wrote:
> > > > > On Sat, Feb 25, 2023 at 05:01:10PM -0800, Paul E. McKenney wrote:
> > > > > > A few other oddities:
> > > > > > 
> > > > > > litmus/auto/C-LB-Lww+R-OC.litmus
> > > > > > 
> > > > > > 	Both versions flag a data race, which I am not seeing.	It appears
> > > > > > 	to me that P1's store to u0 cannot happen unless P0's store
> > > > > > 	has completed.  So what am I missing here?
> > > > > The LKMM doesn't believe that a control or data dependency orders a
> > > > > plain write after a marked read.  Hence in this test it thinks that P1's
> > > > > store to u0 can happen before the load of x1.  I don't remember why we
> > > > > did it this way -- probably we just wanted to minimize the restrictions
> > > > > on when plain accesses can execute.  (I do remember the reason for
> > > > > making address dependencies induce order; it was so RCU would work.)
> > > > > 
> > > > Because plain store can be optimzed as an "store only if not equal"?
> > > > As the following sentenses in the explanations.txt:
> > > > 
> > > > 	The need to distinguish between r- and w-bounding raises yet another
> > > > 	issue.  When the source code contains a plain store, the compiler is
> > > > 	allowed to put plain loads of the same location into the object code.
> > > > 	For example, given the source code:
> > > > 
> > > > 		x = 1;
> > > > 
> > > > 	the compiler is theoretically allowed to generate object code that
> > > > 	looks like:
> > > > 
> > > > 		if (x != 1)
> > > > 			x = 1;
> > > > 
> > > > 	thereby adding a load (and possibly replacing the store entirely).
> > > > 	For this reason, whenever the LKMM requires a plain store to be
> > > > 	w-pre-bounded or w-post-bounded by a marked access, it also requires
> > > > 	the store to be r-pre-bounded or r-post-bounded, so as to handle cases
> > > > 	where the compiler adds a load.
> > > Good guess; maybe that was the reason.  [...]
> > > So perhaps the original reason is not valid now
> > > that the memory model explicitly includes tests for stores being
> > > r-pre/post-bounded.
> > > 
> > > Alan
> > 
> > I agree, I think you could relax that condition.
> 
> Here's a related question to think about.  Suppose a compiler does make 
> this change, adding a load-and-test in front of a store.  Can that load 
> cause a data race?
> 
> Normally I'd say no, because compilers aren't allowed to create data 
> races where one didn't already exist.  But that restriction is part of 
> the C/C++ standard, and what we consider to be a data race differs from 
> what the standard considers.
> 
> So what's the answer?  Is the compiler allowed to translate:
> 
> 	r1 = READ_ONCE(*x);
> 	if (r1)
> 		*y = 1;
> 
> into something resembling:
> 
> 	r1 = READ_ONCE(*x);
> 	rtemp = *y;
> 	if (r1) {
> 		if (rtemp != 1)
> 			*y = 1;
> 	}
> 
> (Note that whether the load to rtemp occurs inside the "if (r1)" 
> conditional or not makes no difference; either way the CPU can execute 
> it before testing the condition.  Even before reading the value of *x.)
> 
> _If_ we assume that these manufactured loads can never cause a data race 
> then it should be safe to remove the r-pre/post-bounded tests for plain 
> writes.
> 
> But what if rtemp reads from a plain write that was torn, and the 
> intermediate value it observes happens to be 1, even though neither the 
> initial nor the final value of *y was 1?

I am not worried about compilers creating data races, so that assignment
to rtemp would be within the "if (r1)" statement.  Not that this matters,
as you say, from a hardware ordering viewpoint.

However, tearing is a concern.  Just to make sure I undersand, one
scenario might be where the initial value of *y was zero and the final
value was 0x10001, correct?  In that case, we have seen compilers that
would write that constant 16 bits at a time, resulting in an transitory
value of 0x1.

But in this case, we would need the value to -not- be 1 for bad things
to happen, correct?

And in that case, we would need the value to initially be 1 and the
desired value to be 1 and some other store to redundantly set it to
1, but tear is such a way that the transitory value is not 1, correct?
Plus we should detect the data race in that case, not?

Or am I missing yet another opportunity for a mischievous compiler?

> > Note there's also rw-xbstar (used with fr) which doesn't check for
> > r-pre-bounded, but it should be ok. That's because only reads would be
> > unordered, as a result the read (in the if (x != ..) x=..) should provide
> > the correct value. The store would be issued as necessary, and the issued
> > store would still be ordered correctly w.r.t the read.
> 
> That isn't the reason I left r-pre-bounded out from rw-xbstar.  If the 
> write gets changed to a read there's no need for rw-xbstar to check 
> r-pre-bounded, because then rw-race would be comparing a read with 
> another read (instead of with a write) and so there would be no 
> possibility of a race in any case.

True, and if there was a racing write, it would be a data race in
any case.

							Thanx, Paul

  reply	other threads:[~2023-02-26 18:45 UTC|newest]

Thread overview: 31+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-02-24 13:52 Jonas Oberhauser
2023-02-24 15:32 ` Alan Stern
2023-02-24 18:37   ` Paul E. McKenney
2023-02-26  1:01     ` Paul E. McKenney
2023-02-26  2:29       ` Alan Stern
2023-02-26  3:03         ` Paul E. McKenney
2023-02-26 18:49           ` Paul E. McKenney
2023-02-26  3:09         ` Boqun Feng
2023-02-26  3:30           ` Alan Stern
2023-02-26 11:17             ` Jonas Oberhauser
2023-02-26 16:51               ` Alan Stern
2023-02-26 18:45                 ` Paul E. McKenney [this message]
2023-02-26 19:32                   ` Alan Stern
2023-02-27 14:03                 ` Jonas Oberhauser
2023-02-27 16:16                   ` Alan Stern
2023-02-27 16:50                     ` Jonas Oberhauser
2023-02-27 18:41                       ` Alan Stern
2023-02-27 19:40         ` Andrea Parri
2023-02-27 20:13           ` Jonas Oberhauser
2023-02-27 22:21             ` Paul E. McKenney
2023-02-28  8:49               ` Jonas Oberhauser
2023-02-28 15:40                 ` Paul E. McKenney
2023-03-01 10:52                   ` Jonas Oberhauser
2023-03-02  1:42                     ` Paul E. McKenney
2023-02-26  2:58       ` Paul E. McKenney
2023-02-26 16:23 ` Joel Fernandes
2023-02-27 14:39   ` Jonas Oberhauser
2023-02-27 17:57     ` Joel Fernandes
2023-02-27 20:24       ` Jonas Oberhauser
2023-02-27 19:35 ` Andrea Parri
2023-02-28 22:01   ` Paul E. McKenney

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20230226184528.GY2948950@paulmck-ThinkPad-P17-Gen-1 \
    --to=paulmck@kernel.org \
    --cc=akiyks@gmail.com \
    --cc=boqun.feng@gmail.com \
    --cc=dhowells@redhat.com \
    --cc=dlustig@nvidia.com \
    --cc=frederic@kernel.org \
    --cc=j.alglave@ucl.ac.uk \
    --cc=joel@joelfernandes.org \
    --cc=jonas.oberhauser@huawei.com \
    --cc=jonas.oberhauser@huaweicloud.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=luc.maranget@inria.fr \
    --cc=npiggin@gmail.com \
    --cc=parri.andrea@gmail.com \
    --cc=peterz@infradead.org \
    --cc=quic_neeraju@quicinc.com \
    --cc=stern@rowland.harvard.edu \
    --cc=urezki@gmail.com \
    --cc=will@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®