[PATCH v3 0/6] Add TPS6594 PMIC support on several boards

mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed

* [PATCH v3 0/6] Add TPS6594 PMIC support on several boards
@ 2023-04-17 15:48 Esteban Blanc
  2023-04-17 15:48 ` [PATCH v3 1/6] arm64: dts: ti: k3-j7200-som-p0: Add TP6594 family PMICs Esteban Blanc
                   ` (5 more replies)
  0 siblings, 6 replies; 7+ messages in thread
From: Esteban Blanc @ 2023-04-17 15:48 UTC (permalink / raw)
  To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt
  Cc: linux-arm-kernel, devicetree, linux-kernel, sterzik, u-kumar1,
	eblanc, jneanne, jpanis, aseketeli

TPS6594 is a Power Management IC which provides regulators and others
features like GPIOs, RTC, watchdog, ESMs (Error Signal Monitor), and
PFSM (Pre-configurable Finite State Machine). The SoC and the PMIC can
communicate through the I2C or SPI interfaces.
TPS6594 is the super-set device while TPS6593 and LP8764 are derivatives.

This serie adds device tree nodes for TI TPS6594 PMICs found in the
following boards:
- J721EXSOMXEVM:
  Link: https://www.ti.com/tool/J721EXSOMXEVM
- J721S2XSOMXEVM:
  Link: https://www.ti.com/tool/J721S2XSOMXEVM
- J7200XSOMXEVM:
  Link: https://www.ti.com/tool/J7200XSOMXEVM
- AM62A-SKEVM:
  Link: https://www.ti.com/tool/SK-AM62A-LP
- J784S4XEVM
  Link: https://www.ti.com/tool/J784S4XEVM

Changes since v1:
https://lore.kernel.org/lkml/20230329142948.833800-1-eblanc@baylibre.com/
- Harmonize regulators names across the different boards
- Adjust AVS voltage range
- Remove some outdated comments
- Add PMIC to J784S4 board
- Compatible string modified to match dt-bindings
- Add gpio-controller and gpio-cells properties

Changes since v2:
https://lore.kernel.org/lkml/20230414112843.1358067-1-eblanc@baylibre.com/
- Change node name as per Krzysztof review
- Add a fix for the interrupt range of wakeup gpio used by TPS6594 pmic
  on J784S4.
  The interruptions of the PMIC were not working before that
- Remove dependencies on other patch series as that was a mistake, see
  https://lore.kernel.org/lkml/CRYY2V3HJ0CP.96JQ18PLZB3C@burritosblues/

Apelete Seketeli (1):
  arm64: dts: ti: k3-j784s4-evm: Fix wakeup gpio pinmux interrupt range

Esteban Blanc (2):
  arm64: dts: ti: k3-j7200-som-p0: Add TP6594 family PMICs
  arm64: dts: ti: k3-j721s2-som-p0: Add TP6594 family PMICs

Jerome Neanne (2):
  arm64: dts: ti: k3-j721e-som-p0: Add TP6594 family PMICs
  arm64: dts: ti: k3-j784s4-evm: Add support for TPS6594 PMIC

Julien Panis (1):
  arm64: dts: ti: k3-am62a7-sk: Add support for TPS6593 PMIC

 arch/arm64/boot/dts/ti/k3-am62a7-sk.dts       |  95 ++++++++
 arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi   | 175 ++++++++++++++
 arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi   | 171 ++++++++++++++
 arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi  | 213 ++++++++++++++++++
 arch/arm64/boot/dts/ti/k3-j784s4-evm.dts      | 116 ++++++++++
 .../boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi     |   2 +-
 6 files changed, 771 insertions(+), 1 deletion(-)

-- 
2.39.2


^ permalink raw reply	[flat|nested] 7+ messages in thread

* [PATCH v3 1/6] arm64: dts: ti: k3-j7200-som-p0: Add TP6594 family PMICs
  2023-04-17 15:48 [PATCH v3 0/6] Add TPS6594 PMIC support on several boards Esteban Blanc
@ 2023-04-17 15:48 ` Esteban Blanc
  2023-04-17 15:48 ` [PATCH v3 2/6] arm64: dts: ti: k3-j721s2-som-p0: " Esteban Blanc
                   ` (4 subsequent siblings)
  5 siblings, 0 replies; 7+ messages in thread
From: Esteban Blanc @ 2023-04-17 15:48 UTC (permalink / raw)
  To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt
  Cc: linux-arm-kernel, devicetree, linux-kernel, sterzik, u-kumar1,
	eblanc, jneanne, jpanis, aseketeli

This patch adds support for TPS6594 PMIC family on wakup I2C0 bus.
Theses devices provides regulators (bucks and LDOs), but also
GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor)
which monitors the SoC error output signal, and a PFSM
(Pre-configurable Finite State Machine) which manages the
operational modes of the PMIC.

Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
---
 arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 175 ++++++++++++++++++++
 1 file changed, 175 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
index fa44ed4c17d5..d2587c24180f 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
@@ -118,6 +118,25 @@ J721E_WKUP_IOPAD(0x0008, PIN_INPUT, 0)  /* MCU_OSPI0_DQS */
 	};
 };
 
+&wkup_pmx2 {
+	/* wkup_pmx2 starts at 0x68 */
+	wkup_i2c0_pins_default: wkup-i2c0-pins-default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0x98, PIN_INPUT_PULLUP, 0) /* (F20) WKUP_I2C0_SCL */
+			J721E_WKUP_IOPAD(0x9c, PIN_INPUT_PULLUP, 0) /* (H21) WKUP_I2C0_SDA */
+		>;
+	};
+};
+
+&wkup_pmx3 {
+	/* wkup_pmx3 starts at 0x174 */
+	pmic_irq_pins_default: pmic-irq-pins-default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0x1c, PIN_INPUT, 7) /* (E18) WKUP_GPIO0_84 */
+		>;
+	};
+};
+
 &main_pmx0 {
 	main_i2c0_pins_default: main-i2c0-pins-default {
 		pinctrl-single,pins = <
@@ -231,3 +250,159 @@ flash@0 {
 		cdns,read-delay = <4>;
 	};
 };
+
+&wkup_i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&wkup_i2c0_pins_default>;
+	clock-frequency = <400000>;
+
+	tps659414: pmic@48 {
+		compatible = "ti,tps6594-q1";
+		reg = <0x48>;
+		ti,primary-pmic;
+		system-power-controller;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_irq_pins_default>;
+		interrupt-parent = <&wkup_gpio0>;
+		interrupts = <84 IRQ_TYPE_EDGE_FALLING>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		buck1-supply = <&vsys_3v3>;
+		buck2-supply = <&vsys_3v3>;
+		buck3-supply = <&vsys_3v3>;
+		buck4-supply = <&vsys_3v3>;
+		buck5-supply = <&vsys_3v3>;
+		ldo1-supply = <&vsys_3v3>;
+		ldo2-supply = <&vsys_3v3>;
+		ldo3-supply = <&vsys_3v3>;
+		ldo4-supply = <&vsys_3v3>;
+
+		regulators {
+			bucka1: buck1 {
+				regulator-name = "vda_mcu_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka2: buck2 {
+				regulator-name = "vdd_mcuio_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka3: buck3 {
+				regulator-name = "vdd_mcu_0v85";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka4: buck4 {
+				regulator-name = "vdd_ddr_1v1";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka5: buck5 {
+				regulator-name = "vdd_phyio_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa1: ldo1 {
+				regulator-name = "vdd1_lpddr4_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa2: ldo2 {
+				regulator-name = "vda_dll_0v8";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa3: ldo3 {
+				regulator-name = "vdd_wk_0v8";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa4: ldo4 {
+				regulator-name = "vda_pll_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+
+	lp876441: pmic@4c {
+		compatible = "ti,lp8764-q1";
+		reg = <0x4c>;
+		system-power-controller;
+		interrupt-parent = <&wkup_gpio0>;
+		interrupts = <84 IRQ_TYPE_EDGE_FALLING>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		buck1-supply = <&vsys_3v3>;
+		buck2-supply = <&vsys_3v3>;
+		buck3-supply = <&vsys_3v3>;
+		buck4-supply = <&vsys_3v3>;
+
+		regulators: regulators {
+			buckb1: buck1 {
+				regulator-name = "vdd_cpu_avs";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <900000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buckb2: buck2 {
+				regulator-name = "vdd_ram_0v85";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buckb3: buck3 {
+				regulator-name = "vdd_core_0v85";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buckb4: buck4 {
+				regulator-name = "vdd_io_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+};
-- 
2.39.2


^ permalink raw reply	[flat|nested] 7+ messages in thread

* [PATCH v3 2/6] arm64: dts: ti: k3-j721s2-som-p0: Add TP6594 family PMICs
  2023-04-17 15:48 [PATCH v3 0/6] Add TPS6594 PMIC support on several boards Esteban Blanc
  2023-04-17 15:48 ` [PATCH v3 1/6] arm64: dts: ti: k3-j7200-som-p0: Add TP6594 family PMICs Esteban Blanc
@ 2023-04-17 15:48 ` Esteban Blanc
  2023-04-17 15:48 ` [PATCH v3 3/6] arm64: dts: ti: k3-j721e-som-p0: " Esteban Blanc
                   ` (3 subsequent siblings)
  5 siblings, 0 replies; 7+ messages in thread
From: Esteban Blanc @ 2023-04-17 15:48 UTC (permalink / raw)
  To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt
  Cc: linux-arm-kernel, devicetree, linux-kernel, sterzik, u-kumar1,
	eblanc, jneanne, jpanis, aseketeli

This patch adds support for TPS6594 PMIC family on wakup I2C0 bus.
Theses devices provides regulators (bucks and LDOs), but also
GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor)
which monitors the SoC error output signal, and a PFSM
(Pre-configurable Finite State Machine) which manages the
operational modes of the PMIC.

Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
---
 arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 213 +++++++++++++++++++
 1 file changed, 213 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
index 6930efff8a5a..9e312c35afdc 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
@@ -79,3 +79,216 @@ &main_mcan16 {
 	pinctrl-names = "default";
 	phys = <&transceiver0>;
 };
+
+&wkup_pmx0 {
+	pmic_irq_pins_default: pmic-irq-pins-default {
+		pinctrl-single,pins = <
+			/* (C21) MCU_OSPI1_CSn1.WKUP_GPIO0_39 */
+			J721S2_WKUP_IOPAD(0x060, PIN_INPUT, 7)
+		>;
+	};
+
+	wkup_i2c0_pins_default: wkup_i2c0_pins_default {
+		pinctrl-single,pins = <
+			J721S2_WKUP_IOPAD(0x100, PIN_INPUT, 0) /* (H24) WKUP_I2C0_SCL */
+			J721S2_WKUP_IOPAD(0x104, PIN_INPUT, 0) /* (H27) WKUP_I2C0_SDA */
+		>;
+	};
+};
+
+&wkup_i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&wkup_i2c0_pins_default>;
+	clock-frequency = <400000>;
+
+	tps659411: pmic@48 {
+		compatible = "ti,tps6594-q1";
+		reg = <0x48>;
+		ti,primary-pmic;
+		system-power-controller;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_irq_pins_default>;
+		interrupt-parent = <&wkup_gpio0>;
+		interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		buck1234-supply = <&vsys_3v3>;
+		buck5-supply = <&vsys_3v3>;
+		ldo1-supply = <&vsys_3v3>;
+		ldo2-supply = <&vsys_3v3>;
+		ldo3-supply = <&vsys_3v3>;
+		ldo4-supply = <&vsys_3v3>;
+
+		regulators {
+			bucka1234: buck1234 {
+				regulator-name = "vdd_cpu_avs";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka5: buck5 {
+				regulator-name = "vdd_mcu_0v85";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa1: ldo1 {
+				regulator-name = "vdd_mcuwk_0v8";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa2: ldo2 {
+				regulator-name = "vdd_mcu_gpioret_3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa3: ldo3 {
+				regulator-name = "vdd_mcuio_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa4: ldo4 {
+				regulator-name = "vda_mcu_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+
+	tps659414: pmic@4c {
+		compatible = "ti,tps6594-q1";
+		reg = <0x4c>;
+		system-power-controller;
+		interrupt-parent = <&wkup_gpio0>;
+		interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		buck1-supply = <&vsys_3v3>;
+		buck2-supply = <&vsys_3v3>;
+		buck3-supply = <&vsys_3v3>;
+		buck4-supply = <&vsys_3v3>;
+		buck5-supply = <&vsys_3v3>;
+		ldo1-supply = <&vsys_3v3>;
+		ldo2-supply = <&vsys_3v3>;
+		ldo3-supply = <&vsys_3v3>;
+		ldo4-supply = <&vsys_3v3>;
+
+		regulators {
+			buckb1: buck1 {
+				regulator-name = "vdd_io_1v8_reg";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buckb2: buck2 {
+				regulator-name = "vdd_fpd_1v1";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buckb3: buck3 {
+				regulator-name = "vdd_phy_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buckb4: buck4 {
+				regulator-name = "vdd_ddr_1v1";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buckb5: buck5 {
+				regulator-name = "vdd_ram_0v85";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldob1: ldo1 {
+				regulator-name = "vdd_wk_0v8";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldob2: ldo2 {
+				regulator-name = "vdd_gpioret_3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldob3: ldo3 {
+				regulator-name = "vda_dll_0v8";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldob4: ldo4 {
+				regulator-name = "vda_pll_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+
+	lp876411: pmic@58 {
+		compatible = "ti,lp8764-q1";
+		reg = <0x58>;
+		system-power-controller;
+		interrupt-parent = <&wkup_gpio0>;
+		interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		buck1234-supply = <&vsys_3v3>;
+
+		regulators {
+			buckc1234: buck1234 {
+				regulator-name = "vdd_core_0v8";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+};
-- 
2.39.2


^ permalink raw reply	[flat|nested] 7+ messages in thread

* [PATCH v3 3/6] arm64: dts: ti: k3-j721e-som-p0: Add TP6594 family PMICs
  2023-04-17 15:48 [PATCH v3 0/6] Add TPS6594 PMIC support on several boards Esteban Blanc
  2023-04-17 15:48 ` [PATCH v3 1/6] arm64: dts: ti: k3-j7200-som-p0: Add TP6594 family PMICs Esteban Blanc
  2023-04-17 15:48 ` [PATCH v3 2/6] arm64: dts: ti: k3-j721s2-som-p0: " Esteban Blanc
@ 2023-04-17 15:48 ` Esteban Blanc
  2023-04-17 15:48 ` [PATCH v3 4/6] arm64: dts: ti: k3-j784s4-evm: Fix wakeup gpio pinmux interrupt range Esteban Blanc
                   ` (2 subsequent siblings)
  5 siblings, 0 replies; 7+ messages in thread
From: Esteban Blanc @ 2023-04-17 15:48 UTC (permalink / raw)
  To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt
  Cc: linux-arm-kernel, devicetree, linux-kernel, sterzik, u-kumar1,
	eblanc, jneanne, jpanis, aseketeli

From: Jerome Neanne <jneanne@baylibre.com>

This patch adds support for TPS6594 PMIC family on wakup I2C0 bus.
Theses devices provides regulators (bucks and LDOs), but also
GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor)
which monitors the SoC error output signal, and a PFSM
(Pre-configurable Finite State Machine) which manages the
operational modes of the PMIC.

Signed-off-by: Jerome Neanne <jneanne@baylibre.com>
Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
---
 arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi | 171 ++++++++++++++++++++
 1 file changed, 171 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
index e289d5b44356..63be7949315e 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
@@ -150,6 +150,12 @@ J721E_WKUP_IOPAD(0xfc, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SDA */
 		>;
 	};
 
+	pmic_irq_pins_default: pmic-irq-pins-default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0xd4, PIN_INPUT, 7) /* (G26) WKUP_GPIO0_9 */
+		>;
+	};
+
 	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
 		pinctrl-single,pins = <
 			J721E_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* MCU_OSPI0_CLK */
@@ -308,3 +314,168 @@ &c71_0 {
 	memory-region = <&c71_0_dma_memory_region>,
 			<&c71_0_memory_region>;
 };
+
+&wkup_i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&wkup_i2c0_pins_default>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	tps659413: pmic@48 {
+		compatible = "ti,tps6594-q1";
+		reg = <0x48>;
+		system-power-controller;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_irq_pins_default>;
+		interrupt-parent = <&wkup_gpio0>;
+		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+		ti,primary-pmic;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		buck12-supply = <&vsys_3v3>;
+		buck3-supply = <&vsys_3v3>;
+		buck4-supply = <&vsys_3v3>;
+		buck5-supply = <&vsys_3v3>;
+		ldo1-supply = <&vsys_3v3>;
+		ldo2-supply = <&vsys_3v3>;
+		ldo3-supply = <&vsys_3v3>;
+		ldo4-supply = <&vsys_3v3>;
+
+		regulators {
+			bucka12: buck12 {
+				regulator-name = "vdd_cpu_avs";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka3: buck3 {
+				regulator-name = "vdd_mcu_0v85";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka4: buck4 {
+				regulator-name = "vdd_ddr_1v1";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka5: buck5 {
+				regulator-name = "vdd_phyio_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa1: ldo1 {
+				regulator-name = "vdd1_lpddr4_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa2: ldo2 {
+				regulator-name = "vdd_mcuio_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa3: ldo3 {
+				regulator-name = "vdda_dll_0v8";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa4: ldo4 {
+				regulator-name = "vda_mcu_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+
+	tps659411: pmic@4c {
+		compatible = "ti,tps6594-q1";
+		reg = <0x4c>;
+		system-power-controller;
+		interrupt-parent = <&wkup_gpio0>;
+		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		buck1234-supply = <&vsys_3v3>;
+		buck5-supply = <&vsys_3v3>;
+		ldo1-supply = <&vsys_3v3>;
+		ldo2-supply = <&vsys_3v3>;
+		ldo3-supply = <&vsys_3v3>;
+		ldo4-supply = <&vsys_3v3>;
+
+		regulators {
+			buckb1234: buck1234 {
+				regulator-name = "vdd_core_0v8";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buckb5: buck5 {
+				regulator-name = "vdd_ram_0v85";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldob1: ldo1 {
+				regulator-name = "vdd_sd_dv";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldob2: ldo2 {
+				regulator-name = "vdd_usb_3v3";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldob3: ldo3 {
+				regulator-name = "vdd_io_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldob4: ldo4 {
+				regulator-name = "vda_pll_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+
+};
-- 
2.39.2


^ permalink raw reply	[flat|nested] 7+ messages in thread

* [PATCH v3 4/6] arm64: dts: ti: k3-j784s4-evm: Fix wakeup gpio pinmux interrupt range
  2023-04-17 15:48 [PATCH v3 0/6] Add TPS6594 PMIC support on several boards Esteban Blanc
                   ` (2 preceding siblings ...)
  2023-04-17 15:48 ` [PATCH v3 3/6] arm64: dts: ti: k3-j721e-som-p0: " Esteban Blanc
@ 2023-04-17 15:48 ` Esteban Blanc
  2023-04-17 15:48 ` [PATCH v3 5/6] arm64: dts: ti: k3-j784s4-evm: Add support for TPS6594 PMIC Esteban Blanc
  2023-04-17 15:48 ` [PATCH v3 6/6] arm64: dts: ti: k3-am62a7-sk: Add support for TPS6593 PMIC Esteban Blanc
  5 siblings, 0 replies; 7+ messages in thread
From: Esteban Blanc @ 2023-04-17 15:48 UTC (permalink / raw)
  To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt
  Cc: linux-arm-kernel, devicetree, linux-kernel, sterzik, u-kumar1,
	eblanc, jneanne, jpanis, aseketeli

From: Apelete Seketeli <aseketeli@baylibre.com>

This patch fixes the interrupt range of wakeup gpio used by TPS6594 PMIC.

Signed-off-by: Apelete Seketeli <aseketeli@baylibre.com>
Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
---
 arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
index 93952af618f6..a4b19b94b71a 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
@@ -65,7 +65,7 @@ wkup_gpio_intr: interrupt-controller@42200000 {
 		#interrupt-cells = <1>;
 		ti,sci = <&sms>;
 		ti,sci-dev-id = <177>;
-		ti,interrupt-ranges = <16 928 16>;
+		ti,interrupt-ranges = <16 960 16>;
 	};
 
 	mcu_conf: syscon@40f00000 {
-- 
2.39.2


^ permalink raw reply	[flat|nested] 7+ messages in thread

* [PATCH v3 5/6] arm64: dts: ti: k3-j784s4-evm: Add support for TPS6594 PMIC
  2023-04-17 15:48 [PATCH v3 0/6] Add TPS6594 PMIC support on several boards Esteban Blanc
                   ` (3 preceding siblings ...)
  2023-04-17 15:48 ` [PATCH v3 4/6] arm64: dts: ti: k3-j784s4-evm: Fix wakeup gpio pinmux interrupt range Esteban Blanc
@ 2023-04-17 15:48 ` Esteban Blanc
  2023-04-17 15:48 ` [PATCH v3 6/6] arm64: dts: ti: k3-am62a7-sk: Add support for TPS6593 PMIC Esteban Blanc
  5 siblings, 0 replies; 7+ messages in thread
From: Esteban Blanc @ 2023-04-17 15:48 UTC (permalink / raw)
  To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt
  Cc: linux-arm-kernel, devicetree, linux-kernel, sterzik, u-kumar1,
	eblanc, jneanne, jpanis, aseketeli

From: Jerome Neanne <jneanne@baylibre.com>

This patch adds support for TPS65933A PMIC on wkup I2C0 bus.
This device provides regulators (bucks and LDOs), but also
GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor)
which monitors the SoC error output signal, and a PFSM
(Pre-configurable Finite State Machine) which manages the
operational modes of the PMIC.

Signed-off-by: Jerome Neanne <jneanne@baylibre.com>
Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
---
 arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 116 +++++++++++++++++++++++
 1 file changed, 116 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
index 8cd4a7ecc121..f2b95345fb9c 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
@@ -103,6 +103,122 @@ vdd_sd_dv: regulator-TLV71033 {
 	};
 };
 
+&wkup_pmx0 {
+	status = "okay";
+	wkup_i2c0_pins_default: wkup_i2c0_pins_default {
+		pinctrl-single,pins = <
+			J784S4_WKUP_IOPAD(0x100, PIN_INPUT, 0) /* (N33) WKUP_I2C0_SCL */
+			J784S4_WKUP_IOPAD(0x104, PIN_INPUT, 0) /* (N35) WKUP_I2C0_SDA */
+		>;
+	};
+
+	pmic_irq_pins_default: pmic-irq-pins-default {
+		pinctrl-single,pins = <
+			/* (G33) MCU_OSPI1_CSn1.WKUP_GPIO0_39 */
+			J784S4_WKUP_IOPAD(0x060, PIN_INPUT, 7)
+		>;
+	};
+};
+
+&wkup_gpio0 {
+	status = "okay";
+};
+
+&wkup_i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&wkup_i2c0_pins_default>;
+	clock-frequency = <400000>;
+	tps659413: pmic@48 {
+		compatible = "ti,tps6594-q1";
+		reg = <0x48>;
+		system-power-controller;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_irq_pins_default>;
+		interrupt-parent = <&wkup_gpio0>;
+		interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
+		ti,primary-pmic;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		buck12-supply = <&vsys_3v3>;
+		buck3-supply = <&vsys_3v3>;
+		buck4-supply = <&vsys_3v3>;
+		buck5-supply = <&vsys_3v3>;
+		ldo1-supply = <&vsys_3v3>;
+		ldo2-supply = <&vsys_3v3>;
+		ldo3-supply = <&vsys_3v3>;
+		ldo4-supply = <&vsys_3v3>;
+
+		regulators {
+			bucka12: buck12 {
+				regulator-name = "vdd_ddr_1v1";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka3: buck3 {
+				regulator-name = "vdd_ram_0v85";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka4: buck4 {
+				regulator-name = "vdd_io_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka5: buck5 {
+				regulator-name = "vdd_mcu_0v85";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa1: ldo1 {
+				regulator-name = "vdd_mcuio_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa2: ldo2 {
+				regulator-name = "vdd_mcuio_3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa3: ldo3 {
+				regulator-name = "vds_dll_0v8";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa4: ldo4 {
+				regulator-name = "vda_mcu_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
 &main_pmx0 {
 	main_uart8_pins_default: main-uart8-pins-default {
 		pinctrl-single,pins = <
-- 
2.39.2


^ permalink raw reply	[flat|nested] 7+ messages in thread

* [PATCH v3 6/6] arm64: dts: ti: k3-am62a7-sk: Add support for TPS6593 PMIC
  2023-04-17 15:48 [PATCH v3 0/6] Add TPS6594 PMIC support on several boards Esteban Blanc
                   ` (4 preceding siblings ...)
  2023-04-17 15:48 ` [PATCH v3 5/6] arm64: dts: ti: k3-j784s4-evm: Add support for TPS6594 PMIC Esteban Blanc
@ 2023-04-17 15:48 ` Esteban Blanc
  5 siblings, 0 replies; 7+ messages in thread
From: Esteban Blanc @ 2023-04-17 15:48 UTC (permalink / raw)
  To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt
  Cc: linux-arm-kernel, devicetree, linux-kernel, sterzik, u-kumar1,
	eblanc, jneanne, jpanis, aseketeli

From: Julien Panis <jpanis@baylibre.com>

This patch adds support for TPS6593 PMIC on main I2C0 bus.
This device provides regulators (bucks and LDOs), but also
GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor)
which monitors the SoC error output signal, and a PFSM
(Pre-configurable Finite State Machine) which manages the
operational modes of the PMIC.

Signed-off-by: Julien Panis <jpanis@baylibre.com>
Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
---
 arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 95 +++++++++++++++++++++++++
 1 file changed, 95 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
index 5c9012141ee2..8484cd987646 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
@@ -191,11 +191,106 @@ AM62AX_IOPAD(0x12c, PIN_INPUT, 0) /* (W16) RGMII1_TX_CTL */
 	};
 };
 
+&mcu_pmx0 {
+	status = "okay";
+
+	pmic_irq_pins_default: pmic-irq-pins-default {
+		pinctrl-single,pins = <
+			AM62AX_MCU_IOPAD(0x000, PIN_INPUT, 7) /* (E11) MCU_GPIO0_0 */
+		>;
+	};
+};
+
+&mcu_gpio0 {
+	status = "okay";
+};
+
 &main_i2c0 {
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_i2c0_pins_default>;
 	clock-frequency = <400000>;
+
+	tps659312: pmic@48 {
+		compatible = "ti,tps6593-q1";
+		reg = <0x48>;
+		ti,primary-pmic;
+		system-power-controller;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_irq_pins_default>;
+		interrupt-parent = <&mcu_gpio0>;
+		interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+
+		buck123-supply = <&vcc_3v3_sys>;
+		buck4-supply = <&vcc_3v3_sys>;
+		buck5-supply = <&vcc_3v3_sys>;
+		ldo1-supply = <&vcc_3v3_sys>;
+		ldo2-supply = <&vcc_3v3_sys>;
+		ldo3-supply = <&buck5>;
+		ldo4-supply = <&vcc_3v3_sys>;
+
+		regulators {
+			buck123: buck123 {
+				regulator-name = "vcc_core";
+				regulator-min-microvolt = <715000>;
+				regulator-max-microvolt = <895000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck4: buck4 {
+				regulator-name = "vcc_1v1";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck5: buck5 {
+				regulator-name = "vcc_1v8_sys";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo1: ldo1 {
+				regulator-name = "vddshv5_sdio";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo2: ldo2 {
+				regulator-name = "vpp_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo3: ldo3 {
+				regulator-name = "vcc_0v85";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo4: ldo4 {
+				regulator-name = "vdda_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
 };
 
 &main_i2c1 {
-- 
2.39.2


^ permalink raw reply	[flat|nested] 7+ messages in thread

end of thread, other threads:[~2023-04-17 15:49 UTC | newest]

Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2023-04-17 15:48 [PATCH v3 0/6] Add TPS6594 PMIC support on several boards Esteban Blanc
2023-04-17 15:48 ` [PATCH v3 1/6] arm64: dts: ti: k3-j7200-som-p0: Add TP6594 family PMICs Esteban Blanc
2023-04-17 15:48 ` [PATCH v3 2/6] arm64: dts: ti: k3-j721s2-som-p0: " Esteban Blanc
2023-04-17 15:48 ` [PATCH v3 3/6] arm64: dts: ti: k3-j721e-som-p0: " Esteban Blanc
2023-04-17 15:48 ` [PATCH v3 4/6] arm64: dts: ti: k3-j784s4-evm: Fix wakeup gpio pinmux interrupt range Esteban Blanc
2023-04-17 15:48 ` [PATCH v3 5/6] arm64: dts: ti: k3-j784s4-evm: Add support for TPS6594 PMIC Esteban Blanc
2023-04-17 15:48 ` [PATCH v3 6/6] arm64: dts: ti: k3-am62a7-sk: Add support for TPS6593 PMIC Esteban Blanc

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®