From: Mario Limonciello <mario.limonciello@amd.com>
To: Natikar Basavaraj <Basavaraj.Natikar@amd.com>,
S-k Shyam-sundar <Shyam-sundar.S-k@amd.com>,
<linus.walleij@linaro.org>
Cc: <andriy.shevchenko@linux.intel.com>, <npliashechnikov@gmail.com>,
<nmschulte@gmail.com>, <friedrich.vock@gmx.de>,
<dridri85@gmail.com>, "Hans de Goede" <hdegoede@redhat.com>,
open list <linux-kernel@vger.kernel.org>,
"open list" <linux-gpio@vger.kernel.org>,
Mario Limonciello <mario.limonciello@amd.com>
Subject: [PATCH v2 4/4] pinctrl: amd: Unify debounce handling into amd_pinconf_set()
Date: Wed, 5 Jul 2023 08:30:05 -0500 [thread overview]
Message-ID: <20230705133005.577-5-mario.limonciello@amd.com> (raw)
In-Reply-To: <20230705133005.577-1-mario.limonciello@amd.com>
Debounce handling is done in two different entry points in the driver.
Unify this to make sure that it's always handled the same.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
---
v1->v2:
* Move later in the series
* Unsigned -> unsigned int
* s/out/out_unlock/
---
drivers/pinctrl/pinctrl-amd.c | 21 +++++----------------
1 file changed, 5 insertions(+), 16 deletions(-)
diff --git a/drivers/pinctrl/pinctrl-amd.c b/drivers/pinctrl/pinctrl-amd.c
index 44d3193a81f2a..b129d7c76b3e9 100644
--- a/drivers/pinctrl/pinctrl-amd.c
+++ b/drivers/pinctrl/pinctrl-amd.c
@@ -115,16 +115,12 @@ static void amd_gpio_set_value(struct gpio_chip *gc, unsigned offset, int value)
raw_spin_unlock_irqrestore(&gpio_dev->lock, flags);
}
-static int amd_gpio_set_debounce(struct gpio_chip *gc, unsigned offset,
- unsigned debounce)
+static int amd_gpio_set_debounce(struct amd_gpio *gpio_dev, unsigned int offset,
+ unsigned int debounce)
{
u32 time;
u32 pin_reg;
int ret = 0;
- unsigned long flags;
- struct amd_gpio *gpio_dev = gpiochip_get_data(gc);
-
- raw_spin_lock_irqsave(&gpio_dev->lock, flags);
/* Use special handling for Pin0 debounce */
if (offset == 0) {
@@ -183,7 +179,6 @@ static int amd_gpio_set_debounce(struct gpio_chip *gc, unsigned offset,
pin_reg &= ~(DB_CNTRl_MASK << DB_CNTRL_OFF);
}
writel(pin_reg, gpio_dev->base + offset * 4);
- raw_spin_unlock_irqrestore(&gpio_dev->lock, flags);
return ret;
}
@@ -782,9 +777,8 @@ static int amd_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
switch (param) {
case PIN_CONFIG_INPUT_DEBOUNCE:
- pin_reg &= ~DB_TMR_OUT_MASK;
- pin_reg |= arg & DB_TMR_OUT_MASK;
- break;
+ ret = amd_gpio_set_debounce(gpio_dev, pin, arg);
+ goto out_unlock;
case PIN_CONFIG_BIAS_PULL_DOWN:
pin_reg &= ~BIT(PULL_DOWN_ENABLE_OFF);
@@ -811,6 +805,7 @@ static int amd_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
writel(pin_reg, gpio_dev->base + pin*4);
}
+out_unlock:
raw_spin_unlock_irqrestore(&gpio_dev->lock, flags);
return ret;
@@ -857,12 +852,6 @@ static int amd_gpio_set_config(struct gpio_chip *gc, unsigned int pin,
{
struct amd_gpio *gpio_dev = gpiochip_get_data(gc);
- if (pinconf_to_config_param(config) == PIN_CONFIG_INPUT_DEBOUNCE) {
- u32 debounce = pinconf_to_config_argument(config);
-
- return amd_gpio_set_debounce(gc, pin, debounce);
- }
-
return amd_pinconf_set(gpio_dev->pctrl, pin, &config, 1);
}
--
2.34.1
next prev parent reply other threads:[~2023-07-05 13:31 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-07-05 13:30 [PATCH v2 0/4] Fix for interrupt storm on ASUS TUF A16 Mario Limonciello
2023-07-05 13:30 ` [PATCH v2 1/4] pinctrl: amd: Only use special debounce behavior for GPIO 0 Mario Limonciello
2023-07-05 13:30 ` [PATCH v2 2/4] pinctrl: amd: Use amd_pinconf_set() for all config options Mario Limonciello
2023-07-06 9:16 ` Andy Shevchenko
2023-07-06 14:30 ` Limonciello, Mario
2023-07-05 13:30 ` [PATCH v2 3/4] pinctrl: amd: Drop pull up select configuration Mario Limonciello
2023-07-05 13:30 ` Mario Limonciello [this message]
2023-07-07 13:50 ` [PATCH v2 0/4] Fix for interrupt storm on ASUS TUF A16 Linus Walleij
2023-07-07 14:09 ` Limonciello, Mario
2023-07-10 17:49 ` Jan Visser
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230705133005.577-5-mario.limonciello@amd.com \
--to=mario.limonciello@amd.com \
--cc=Basavaraj.Natikar@amd.com \
--cc=Shyam-sundar.S-k@amd.com \
--cc=andriy.shevchenko@linux.intel.com \
--cc=dridri85@gmail.com \
--cc=friedrich.vock@gmx.de \
--cc=hdegoede@redhat.com \
--cc=linus.walleij@linaro.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=nmschulte@gmail.com \
--cc=npliashechnikov@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®