[PATCH v2 0/6] arm64: ti: Enable audio on AM62A

[PATCH v2 0/6] arm64: ti: Enable audio on AM62A

[Jai Luthra]

This patch series adds support for audio via headphone jack on
SK-AM62A-LP. The jack is wired to TLV320AIC3106 (codec), which is
connected to McASP1 (serializer) on the SoC.

The TRRS 3.5mm jack can be used for simultaneous playback and recording.

Signed-off-by: Jai Luthra <j-luthra@ti.com>
---
Changes in v2:
- Move the patch that enables TPS6593 PMIC to this series
- Link to v1: https://lore.kernel.org/r/20230731-mcasp_am62a-v1-0-8bd137ffa8f1@ti.com

---
Jai Luthra (5):
      arm64: dts: ti: k3-am62a-main: Add nodes for McASP
      arm64: dts: ti: k3-am62a7-sk: Split vcc_3v3 regulators
      arm64: dts: ti: k3-am62a7-sk: Drop i2c-1 to 100Khz
      arm64: dts: ti: k3-am62a7-sk: Enable audio on AM62A
      arm64: defconfig: Enable TPS6593 PMIC for SK-AM62A

Julien Panis (1):
      arm64: dts: ti: k3-am62a7-sk: Add support for TPS6593 PMIC

 arch/arm64/boot/dts/ti/k3-am62a-main.dtsi |  60 ++++++++++
 arch/arm64/boot/dts/ti/k3-am62a7-sk.dts   | 189 +++++++++++++++++++++++++++++-
 arch/arm64/configs/defconfig              |   1 +
 3 files changed, 247 insertions(+), 3 deletions(-)
---
base-commit: 18030226a48de1fbfabf4ae16aaa2695a484254f
change-id: 20230731-mcasp_am62a-af1660624f97

Best regards,
-- 
Jai Luthra <j-luthra@ti.com>

[PATCH v2 1/6] arm64: dts: ti: k3-am62a-main: Add nodes for McASP

[Jai Luthra]

Same as AM62, AM62A has three instances of McASP which can be used for
transmitting or receiving digital audio in various formats.

Reviewed-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am62a-main.dtsi | 60 +++++++++++++++++++++++++++++++
 1 file changed, 60 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi
index 3198af08fb9f..4ae7fdc5221b 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi
@@ -816,4 +816,64 @@ ecap2: pwm@23120000 {
 		clock-names = "fck";
 		status = "disabled";
 	};
+
+	mcasp0: audio-controller@2b00000 {
+		compatible = "ti,am33xx-mcasp-audio";
+		reg = <0x00 0x02b00000 0x00 0x2000>,
+		      <0x00 0x02b08000 0x00 0x400>;
+		reg-names = "mpu", "dat";
+		interrupts = <GIC_SPI 236 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "tx", "rx";
+
+		dmas = <&main_bcdma 0 0xc500 0>, <&main_bcdma 0 0x4500 0>;
+		dma-names = "tx", "rx";
+
+		clocks = <&k3_clks 190 0>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 190 0>;
+		assigned-clock-parents = <&k3_clks 190 2>;
+		power-domains = <&k3_pds 190 TI_SCI_PD_EXCLUSIVE>;
+		status = "disabled";
+	};
+
+	mcasp1: audio-controller@2b10000 {
+		compatible = "ti,am33xx-mcasp-audio";
+		reg = <0x00 0x02b10000 0x00 0x2000>,
+		      <0x00 0x02b18000 0x00 0x400>;
+		reg-names = "mpu", "dat";
+		interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 237 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "tx", "rx";
+
+		dmas = <&main_bcdma 0 0xc501 0>, <&main_bcdma 0 0x4501 0>;
+		dma-names = "tx", "rx";
+
+		clocks = <&k3_clks 191 0>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 191 0>;
+		assigned-clock-parents = <&k3_clks 191 2>;
+		power-domains = <&k3_pds 191 TI_SCI_PD_EXCLUSIVE>;
+		status = "disabled";
+	};
+
+	mcasp2: audio-controller@2b20000 {
+		compatible = "ti,am33xx-mcasp-audio";
+		reg = <0x00 0x02b20000 0x00 0x2000>,
+		      <0x00 0x02b28000 0x00 0x400>;
+		reg-names = "mpu", "dat";
+		interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "tx", "rx";
+
+		dmas = <&main_bcdma 0 0xc502 0>, <&main_bcdma 0 0x4502 0>;
+		dma-names = "tx", "rx";
+
+		clocks = <&k3_clks 192 0>;
+		clock-names = "fck";
+		assigned-clocks = <&k3_clks 192 0>;
+		assigned-clock-parents = <&k3_clks 192 2>;
+		power-domains = <&k3_pds 192 TI_SCI_PD_EXCLUSIVE>;
+		status = "disabled";
+	};
 };

-- 
2.42.0

[PATCH v2 2/6] arm64: dts: ti: k3-am62a7-sk: Split vcc_3v3 regulators

[Jai Luthra]

VCC_3V3_MAIN is the output of LM5141-Q1, and it serves as an input to
TPS22965DSGT which produces VCC_3V3_SYS. [1]

Link: https://www.ti.com/lit/zip/sprr459 [1]
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 15 +++++++++++++--
 1 file changed, 13 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
index cff283c75f8e..c689d3da2def 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
@@ -79,10 +79,10 @@ vcc_5v0: regulator-1 {
 		regulator-boot-on;
 	};
 
-	vcc_3v3_sys: regulator-2 {
+	vcc_3v3_main: regulator-2 {
 		/* output of LM5141-Q1 */
 		compatible = "regulator-fixed";
-		regulator-name = "vcc_3v3_sys";
+		regulator-name = "vcc_3v3_main";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 		vin-supply = <&vmain_pd>;
@@ -101,6 +101,17 @@ vdd_mmc1: regulator-3 {
 		gpio = <&exp1 3 GPIO_ACTIVE_HIGH>;
 	};
 
+	vcc_3v3_sys: regulator-4 {
+		/* output of TPS222965DSGT */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_3v3_sys";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_3v3_main>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";

-- 
2.42.0

[PATCH v2 3/6] arm64: dts: ti: k3-am62a7-sk: Drop i2c-1 to 100Khz

[Jai Luthra]

The TLV320AIC3106 audio codec is interfaced on the i2c-1 bus. With the
default rate of 400Khz the i2c register writes fail to sync:

[   36.026387] tlv320aic3x 1-001b: Unable to sync registers 0x16-0x16. -110
[   38.101130] omap_i2c 20010000.i2c: controller timed out

Dropping the rate to 100Khz fixes the issue.

Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
index c689d3da2def..866b2725f775 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
@@ -261,7 +261,7 @@ &main_i2c1 {
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_i2c1_pins_default>;
-	clock-frequency = <400000>;
+	clock-frequency = <100000>;
 
 	exp1: gpio@22 {
 		compatible = "ti,tca6424";

-- 
2.42.0

Re: [PATCH v2 3/6] arm64: dts: ti: k3-am62a7-sk: Drop i2c-1 to 100Khz

[Aradhya Bhatia]

On 28-Sep-23 14:54, Jai Luthra wrote:
> The TLV320AIC3106 audio codec is interfaced on the i2c-1 bus. With the
> default rate of 400Khz the i2c register writes fail to sync:
> 
> [   36.026387] tlv320aic3x 1-001b: Unable to sync registers 0x16-0x16. -110
> [   38.101130] omap_i2c 20010000.i2c: controller timed out
> 
> Dropping the rate to 100Khz fixes the issue.
> 
> Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
> Signed-off-by: Jai Luthra <j-luthra@ti.com>

Since the codec wouldn't have worked with the 400KHz, the initial DT
configuration is wrong, which makes this patch a fix, and should be
indicated as such.

With the Fixes tag added,

Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>

Regards
Aradhya

> ---
>  arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
> index c689d3da2def..866b2725f775 100644
> --- a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
> @@ -261,7 +261,7 @@ &main_i2c1 {
>  	status = "okay";
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&main_i2c1_pins_default>;
> -	clock-frequency = <400000>;
> +	clock-frequency = <100000>;
>  
>  	exp1: gpio@22 {
>  		compatible = "ti,tca6424";
> 

Re: [PATCH v2 3/6] arm64: dts: ti: k3-am62a7-sk: Drop i2c-1 to 100Khz

[Jai Luthra]

[-- Attachment #1: Type: text/plain, Size: 2028 bytes --]

Hi Aradhya,

On Oct 03, 2023 at 10:54:12 +0530, Aradhya Bhatia wrote:
> 
> 
> On 28-Sep-23 14:54, Jai Luthra wrote:
> > The TLV320AIC3106 audio codec is interfaced on the i2c-1 bus. With the
> > default rate of 400Khz the i2c register writes fail to sync:
> > 
> > [   36.026387] tlv320aic3x 1-001b: Unable to sync registers 0x16-0x16. -110
> > [   38.101130] omap_i2c 20010000.i2c: controller timed out
> > 
> > Dropping the rate to 100Khz fixes the issue.
> > 
> > Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
> > Signed-off-by: Jai Luthra <j-luthra@ti.com>
> 
> Since the codec wouldn't have worked with the 400KHz, the initial DT
> configuration is wrong, which makes this patch a fix, and should be
> indicated as such.

I am slightly confused, as the codec node was not enumerated before this 
series, and i2c-1 configuration @ 400Khz works for the GPIO expanders 
present.

My understanding is that a Fixes: tag would mean we backport this patch 
to older releases, but that would not really be necessary here as 
nothing was per se "broken" before this series.

Will discuss this offline with you and Vignesh and send a v3.

> 
> With the Fixes tag added,
> 
> Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
> 
> Regards
> Aradhya
> 
> > ---
> >  arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 2 +-
> >  1 file changed, 1 insertion(+), 1 deletion(-)
> > 
> > diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
> > index c689d3da2def..866b2725f775 100644
> > --- a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
> > +++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
> > @@ -261,7 +261,7 @@ &main_i2c1 {
> >  	status = "okay";
> >  	pinctrl-names = "default";
> >  	pinctrl-0 = <&main_i2c1_pins_default>;
> > -	clock-frequency = <400000>;
> > +	clock-frequency = <100000>;
> >  
> >  	exp1: gpio@22 {
> >  		compatible = "ti,tca6424";
> > 
> 

-- 
Thanks,
Jai

GPG Fingerprint: 4DE0 D818 E5D5 75E8 D45A AFC5 43DE 91F9 249A 7145

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

[PATCH v2 4/6] arm64: dts: ti: k3-am62a7-sk: Add support for TPS6593 PMIC

[Jai Luthra]

From: Julien Panis <jpanis@baylibre.com>

This patch adds support for TPS6593 PMIC on main I2C0 bus.
This device provides regulators (bucks and LDOs), but also
GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor)
which monitors the SoC error output signal, and a PFSM
(Pre-configurable Finite State Machine) which manages the
operational modes of the PMIC.

Signed-off-by: Julien Panis <jpanis@baylibre.com>
Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 95 +++++++++++++++++++++++++++++++++
 1 file changed, 95 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
index 866b2725f775..377ab823bbcc 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
@@ -232,6 +232,20 @@ AM62AX_IOPAD(0x12c, PIN_INPUT, 0) /* (W16) RGMII1_TX_CTL */
 	};
 };
 
+&mcu_pmx0 {
+	status = "okay";
+
+	pmic_irq_pins_default: pmic-irq-default-pins {
+		pinctrl-single,pins = <
+			AM62AX_MCU_IOPAD(0x000, PIN_INPUT, 7) /* (E11) MCU_GPIO0_0 */
+		>;
+	};
+};
+
+&mcu_gpio0 {
+	status = "okay";
+};
+
 &main_i2c0 {
 	status = "okay";
 	pinctrl-names = "default";
@@ -255,6 +269,87 @@ usb_con_hs: endpoint {
 			};
 		};
 	};
+
+	tps659312: pmic@48 {
+		compatible = "ti,tps6593-q1";
+		reg = <0x48>;
+		ti,primary-pmic;
+		system-power-controller;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_irq_pins_default>;
+		interrupt-parent = <&mcu_gpio0>;
+		interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+
+		buck123-supply = <&vcc_3v3_sys>;
+		buck4-supply = <&vcc_3v3_sys>;
+		buck5-supply = <&vcc_3v3_sys>;
+		ldo1-supply = <&vcc_3v3_sys>;
+		ldo2-supply = <&vcc_3v3_sys>;
+		ldo3-supply = <&buck5>;
+		ldo4-supply = <&vcc_3v3_sys>;
+
+		regulators {
+			buck123: buck123 {
+				regulator-name = "vcc_core";
+				regulator-min-microvolt = <715000>;
+				regulator-max-microvolt = <895000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck4: buck4 {
+				regulator-name = "vcc_1v1";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck5: buck5 {
+				regulator-name = "vcc_1v8_sys";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo1: ldo1 {
+				regulator-name = "vddshv5_sdio";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo2: ldo2 {
+				regulator-name = "vpp_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo3: ldo3 {
+				regulator-name = "vcc_0v85";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo4: ldo4 {
+				regulator-name = "vdda_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
 };
 
 &main_i2c1 {

-- 
2.42.0

[PATCH v2 5/6] arm64: dts: ti: k3-am62a7-sk: Enable audio on AM62A

[Jai Luthra]

Add nodes for audio codec and sound card, enable the audio serializer
(McASP1) under use and update pinmux.

Reviewed-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Link: https://www.ti.com/lit/zip/sprr459
Signed-off-by: Jai Luthra <j-luthra@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 77 +++++++++++++++++++++++++++++++++
 1 file changed, 77 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
index 377ab823bbcc..694eb36b4eb9 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
@@ -125,6 +125,41 @@ led-0 {
 			default-state = "off";
 		};
 	};
+
+	tlv320_mclk: clk-0 {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <12288000>;
+	};
+
+	codec_audio: sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "AM62Ax-SKEVM";
+		simple-audio-card,widgets =
+			"Headphone",	"Headphone Jack",
+			"Line",		"Line In",
+			"Microphone",	"Microphone Jack";
+		simple-audio-card,routing =
+			"Headphone Jack",	"HPLOUT",
+			"Headphone Jack",	"HPROUT",
+			"LINE1L",		"Line In",
+			"LINE1R",		"Line In",
+			"MIC3R",		"Microphone Jack",
+			"Microphone Jack",	"Mic Bias";
+		simple-audio-card,format = "dsp_b";
+		simple-audio-card,bitclock-master = <&sound_master>;
+		simple-audio-card,frame-master = <&sound_master>;
+		simple-audio-card,bitclock-inversion;
+
+		simple-audio-card,cpu {
+			sound-dai = <&mcasp1>;
+		};
+
+		sound_master: simple-audio-card,codec {
+			sound-dai = <&tlv320aic3106>;
+			clocks = <&tlv320_mclk>;
+		};
+	};
 };
 
 &mcu_pmx0 {
@@ -230,6 +265,15 @@ AM62AX_IOPAD(0x130, PIN_INPUT, 0) /* (AB17) RGMII1_TXC */
 			AM62AX_IOPAD(0x12c, PIN_INPUT, 0) /* (W16) RGMII1_TX_CTL */
 		>;
 	};
+
+	main_mcasp1_pins_default: main-mcasp1-pins-default {
+		pinctrl-single,pins = <
+			AM62AX_IOPAD(0x090, PIN_INPUT, 2) /* (L19) GPMC0_BE0n_CLE.MCASP1_ACLKX */
+			AM62AX_IOPAD(0x098, PIN_INPUT, 2) /* (R18) GPMC0_WAIT0.MCASP1_AFSX */
+			AM62AX_IOPAD(0x08c, PIN_OUTPUT, 2) /* (K19) GPMC0_WEn.MCASP1_AXR0 */
+			AM62AX_IOPAD(0x084, PIN_INPUT, 2) /* (L18) GPMC0_ADVn_ALE.MCASP1_AXR2 */
+		>;
+	};
 };
 
 &mcu_pmx0 {
@@ -377,6 +421,19 @@ exp1: gpio@22 {
 				   "MCASP1_FET_SEL", "UART1_FET_SEL",
 				   "PD_I2C_IRQ", "IO_EXP_TEST_LED";
 	};
+
+	tlv320aic3106: audio-codec@1b {
+		#sound-dai-cells = <0>;
+		compatible = "ti,tlv320aic3106";
+		reg = <0x1b>;
+		ai3x-micbias-vg = <1>;	/* 2.0V */
+
+		/* Regulators */
+		AVDD-supply = <&vcc_3v3_sys>;
+		IOVDD-supply = <&vcc_3v3_sys>;
+		DRVDD-supply = <&vcc_3v3_sys>;
+		DVDD-supply = <&buck5>;
+	};
 };
 
 &sdhci1 {
@@ -467,3 +524,23 @@ cpsw3g_phy0: ethernet-phy@0 {
 		ti,min-output-impedance;
 	};
 };
+
+&mcasp1 {
+	status = "okay";
+	#sound-dai-cells = <0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mcasp1_pins_default>;
+
+	op-mode = <0>;          /* MCASP_IIS_MODE */
+	tdm-slots = <2>;
+
+	serial-dir = <  /* 0: INACTIVE, 1: TX, 2: RX */
+	       1 0 2 0
+	       0 0 0 0
+	       0 0 0 0
+	       0 0 0 0
+	>;
+	tx-num-evt = <32>;
+	rx-num-evt = <32>;
+};

-- 
2.42.0

Re: [PATCH v2 5/6] arm64: dts: ti: k3-am62a7-sk: Enable audio on AM62A

[Vignesh Raghavendra]

On 28/09/23 14:54, Jai Luthra wrote:
> +
> +	main_mcasp1_pins_default: main-mcasp1-pins-default {


pinctrl-single.yaml mandates node names should end with -pins .

> +		pinctrl-single,pins = <
> +			AM62AX_IOPAD(0x090, PIN_INPUT, 2) /* (L19) GPMC0_BE0n_CLE.MCASP1_ACLKX */
> +			AM62AX_IOPAD(0x098, PIN_INPUT, 2) /* (R18) GPMC0_WAIT0.MCASP1_AFSX */
> +			AM62AX_IOPAD(0x08c, PIN_OUTPUT, 2) /* (K19) GPMC0_WEn.MCASP1_AXR0 */
> +			AM62AX_IOPAD(0x084, PIN_INPUT, 2) /* (L18) GPMC0_ADVn_ALE.MCASP1_AXR2 */
> +		>;
> +	};
>  };
>  

-- 
Regards
Vignesh

[PATCH v2 6/6] arm64: defconfig: Enable TPS6593 PMIC for SK-AM62A

[Jai Luthra]

SK-AM62A-LP uses TPS6593x PMIC (interfaced over I2C) to power the SoC
and various other peripherals on the board [1].

Specifically, the audio codec (TLV320AIC3106) on the board relies on the
PMIC for the DVDD (1.8V) supply.

[1]: https://www.ti.com/lit/zip/sprr459

Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
---
 arch/arm64/configs/defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 66bfbef73324..38f0ce9cd2a3 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -725,6 +725,7 @@ CONFIG_MFD_SEC_CORE=y
 CONFIG_MFD_SL28CPLD=y
 CONFIG_RZ_MTU3=y
 CONFIG_MFD_TPS65219=y
+CONFIG_MFD_TPS6594_I2C=m
 CONFIG_MFD_TI_AM335X_TSCADC=m
 CONFIG_MFD_ROHM_BD718XX=y
 CONFIG_MFD_WCD934X=m

-- 
2.42.0