* [PATCH] usb: dwc3: core: enable CCI support @ 2023-10-13 5:34 Piyush Mehta 2023-10-20 23:16 ` Thinh Nguyen 0 siblings, 1 reply; 6+ messages in thread From: Piyush Mehta @ 2023-10-13 5:34 UTC (permalink / raw) To: gregkh, michal.simek, Thinh.Nguyen Cc: linux-usb, linux-kernel, git, Piyush Mehta The GSBUSCFG0 register bits [31:16] are used to configure the cache type settings of the descriptor and data write/read transfers (Cacheable, Bufferable/ Posted). When CCI is enabled in the design, DWC3 core GSBUSCFG0 cache bits must be updated to support CCI enabled transfers in USB. Signed-off-by: Piyush Mehta <piyush.mehta@amd.com> --- DWC3 Register Map Link: https://docs.xilinx.com/r/en-US/ug1087-zynq-ultrascale-registers/GSBUSCFG0-USB3_XHCI-Register Register Name GSBUSCFG0 Description Global SoC Bus Configuration Register 0 GSBUSCFG0 (USB3_XHCI) Register Bit-Field: DATRDREQINFO 31:28 DESRDREQINFO 27:24 DATWRREQINFO 23:20 DESWRREQINFO 19:16 --- drivers/usb/dwc3/core.c | 17 +++++++++++++++++ drivers/usb/dwc3/core.h | 5 +++++ 2 files changed, 22 insertions(+) diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c index 9c6bf054f15d..fc6892c63abf 100644 --- a/drivers/usb/dwc3/core.c +++ b/drivers/usb/dwc3/core.c @@ -23,6 +23,7 @@ #include <linux/delay.h> #include <linux/dma-mapping.h> #include <linux/of.h> +#include <linux/of_address.h> #include <linux/of_graph.h> #include <linux/acpi.h> #include <linux/pinctrl/consumer.h> @@ -559,6 +560,20 @@ static void dwc3_cache_hwparams(struct dwc3 *dwc) parms->hwparams9 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS9); } +static void dwc3_config_soc_bus(struct dwc3 *dwc) +{ + if (of_dma_is_coherent(dwc->dev->of_node)) { + u32 reg; + + reg = dwc3_readl(dwc->regs, DWC3_GSBUSCFG0); + reg |= DWC3_GSBUSCFG0_DATRDREQINFO_MASK | + DWC3_GSBUSCFG0_DESRDREQINFO_MASK | + DWC3_GSBUSCFG0_DATWRREQINFO_MASK | + DWC3_GSBUSCFG0_DESWRREQINFO_MASK; + dwc3_writel(dwc->regs, DWC3_GSBUSCFG0, reg); + } +} + static int dwc3_core_ulpi_init(struct dwc3 *dwc) { int intf; @@ -1137,6 +1152,8 @@ static int dwc3_core_init(struct dwc3 *dwc) dwc3_set_incr_burst_type(dwc); + dwc3_config_soc_bus(dwc); + ret = dwc3_phy_power_on(dwc); if (ret) goto err_exit_phy; diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h index a69ac67d89fe..bd937025ce05 100644 --- a/drivers/usb/dwc3/core.h +++ b/drivers/usb/dwc3/core.h @@ -173,6 +173,11 @@ #define DWC3_OSTS 0xcc10 /* Bit fields */ +/* Global SoC Bus Configuration Register: AHB-prot/AXI-cache/OCP-ReqInfo */ +#define DWC3_GSBUSCFG0_DATRDREQINFO_MASK GENMASK(31, 28) +#define DWC3_GSBUSCFG0_DESRDREQINFO_MASK GENMASK(27, 24) +#define DWC3_GSBUSCFG0_DATWRREQINFO_MASK GENMASK(23, 20) +#define DWC3_GSBUSCFG0_DESWRREQINFO_MASK GENMASK(19, 16) /* Global SoC Bus Configuration INCRx Register 0 */ #define DWC3_GSBUSCFG0_INCR256BRSTENA (1 << 7) /* INCR256 burst */ -- 2.17.1 ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] usb: dwc3: core: enable CCI support 2023-10-13 5:34 [PATCH] usb: dwc3: core: enable CCI support Piyush Mehta @ 2023-10-20 23:16 ` Thinh Nguyen 2023-11-06 13:48 ` Mehta, Piyush 0 siblings, 1 reply; 6+ messages in thread From: Thinh Nguyen @ 2023-10-20 23:16 UTC (permalink / raw) To: Piyush Mehta Cc: gregkh, michal.simek, Thinh Nguyen, linux-usb, linux-kernel, git On Fri, Oct 13, 2023, Piyush Mehta wrote: > The GSBUSCFG0 register bits [31:16] are used to configure the cache type > settings of the descriptor and data write/read transfers (Cacheable, > Bufferable/ Posted). When CCI is enabled in the design, DWC3 core GSBUSCFG0 > cache bits must be updated to support CCI enabled transfers in USB. > > Signed-off-by: Piyush Mehta <piyush.mehta@amd.com> > --- > DWC3 Register Map Link: > https://urldefense.com/v3/__https://docs.xilinx.com/r/en-US/ug1087-zynq-ultrascale-registers/GSBUSCFG0-USB3_XHCI-Register__;!!A4F2R9G_pg!cbLbYLk9xu54DZMkiTQzMhdCaPA4gmIVInes4ZeNb28AI2pgesEvHNYtjoZfWvE_t7wlUdZvYn-Pio8WjA55ekal$ > Register Name GSBUSCFG0 > Description Global SoC Bus Configuration Register 0 > > GSBUSCFG0 (USB3_XHCI) Register Bit-Field: > DATRDREQINFO 31:28 > DESRDREQINFO 27:24 > DATWRREQINFO 23:20 > DESWRREQINFO 19:16 > --- > drivers/usb/dwc3/core.c | 17 +++++++++++++++++ > drivers/usb/dwc3/core.h | 5 +++++ > 2 files changed, 22 insertions(+) > > diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c > index 9c6bf054f15d..fc6892c63abf 100644 > --- a/drivers/usb/dwc3/core.c > +++ b/drivers/usb/dwc3/core.c > @@ -23,6 +23,7 @@ > #include <linux/delay.h> > #include <linux/dma-mapping.h> > #include <linux/of.h> > +#include <linux/of_address.h> > #include <linux/of_graph.h> > #include <linux/acpi.h> > #include <linux/pinctrl/consumer.h> > @@ -559,6 +560,20 @@ static void dwc3_cache_hwparams(struct dwc3 *dwc) > parms->hwparams9 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS9); > } > > +static void dwc3_config_soc_bus(struct dwc3 *dwc) > +{ > + if (of_dma_is_coherent(dwc->dev->of_node)) { > + u32 reg; > + > + reg = dwc3_readl(dwc->regs, DWC3_GSBUSCFG0); > + reg |= DWC3_GSBUSCFG0_DATRDREQINFO_MASK | > + DWC3_GSBUSCFG0_DESRDREQINFO_MASK | > + DWC3_GSBUSCFG0_DATWRREQINFO_MASK | > + DWC3_GSBUSCFG0_DESWRREQINFO_MASK; > + dwc3_writel(dwc->regs, DWC3_GSBUSCFG0, reg); > + } > +} > + You're overwriting default values for all platforms. Don't do that. Not every platform supports this setting. Only apply these specific settings to your platform. BR, Thinh > static int dwc3_core_ulpi_init(struct dwc3 *dwc) > { > int intf; > @@ -1137,6 +1152,8 @@ static int dwc3_core_init(struct dwc3 *dwc) > > dwc3_set_incr_burst_type(dwc); > > + dwc3_config_soc_bus(dwc); > + > ret = dwc3_phy_power_on(dwc); > if (ret) > goto err_exit_phy; > diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h > index a69ac67d89fe..bd937025ce05 100644 > --- a/drivers/usb/dwc3/core.h > +++ b/drivers/usb/dwc3/core.h > @@ -173,6 +173,11 @@ > #define DWC3_OSTS 0xcc10 > > /* Bit fields */ > +/* Global SoC Bus Configuration Register: AHB-prot/AXI-cache/OCP-ReqInfo */ > +#define DWC3_GSBUSCFG0_DATRDREQINFO_MASK GENMASK(31, 28) > +#define DWC3_GSBUSCFG0_DESRDREQINFO_MASK GENMASK(27, 24) > +#define DWC3_GSBUSCFG0_DATWRREQINFO_MASK GENMASK(23, 20) > +#define DWC3_GSBUSCFG0_DESWRREQINFO_MASK GENMASK(19, 16) > > /* Global SoC Bus Configuration INCRx Register 0 */ > #define DWC3_GSBUSCFG0_INCR256BRSTENA (1 << 7) /* INCR256 burst */ > -- > 2.17.1 > ^ permalink raw reply [flat|nested] 6+ messages in thread
* RE: [PATCH] usb: dwc3: core: enable CCI support 2023-10-20 23:16 ` Thinh Nguyen @ 2023-11-06 13:48 ` Mehta, Piyush 2023-11-10 2:37 ` Thinh Nguyen 0 siblings, 1 reply; 6+ messages in thread From: Mehta, Piyush @ 2023-11-06 13:48 UTC (permalink / raw) To: Thinh Nguyen Cc: gregkh, Simek, Michal, linux-usb, linux-kernel, Paladugu, Siva Durga Prasad, Pandey, Radhey Shyam Hi Thinh, > -----Original Message----- > From: Thinh Nguyen <Thinh.Nguyen@synopsys.com> > Sent: Saturday, October 21, 2023 4:46 AM > To: Mehta, Piyush <piyush.mehta@amd.com> > Cc: gregkh@linuxfoundation.org; Simek, Michal <michal.simek@amd.com>; > Thinh Nguyen <Thinh.Nguyen@synopsys.com>; linux-usb@vger.kernel.org; > linux-kernel@vger.kernel.org; git (AMD-Xilinx) <git@amd.com> > Subject: Re: [PATCH] usb: dwc3: core: enable CCI support > > On Fri, Oct 13, 2023, Piyush Mehta wrote: > > The GSBUSCFG0 register bits [31:16] are used to configure the cache > > type settings of the descriptor and data write/read transfers > > (Cacheable, Bufferable/ Posted). When CCI is enabled in the design, > > DWC3 core GSBUSCFG0 cache bits must be updated to support CCI enabled > transfers in USB. > > > > Signed-off-by: Piyush Mehta <piyush.mehta@amd.com> > > --- > > DWC3 Register Map Link: > > https://urldefense.com/v3/__https://docs.xilinx.com/r/en-US/ug1087-zynq- > ultrascale-registers/GSBUSCFG0-USB3_XHCI- > Register__;!!A4F2R9G_pg!cbLbYLk9xu54DZMkiTQzMhdCaPA4gmIVInes4ZeNb28 > AI2pgesEvHNYtjoZfWvE_t7wlUdZvYn-Pio8WjA55ekal$ > > Register Name GSBUSCFG0 > > Description Global SoC Bus Configuration Register 0 > > > > GSBUSCFG0 (USB3_XHCI) Register Bit-Field: > > DATRDREQINFO 31:28 > > DESRDREQINFO 27:24 > > DATWRREQINFO 23:20 > > DESWRREQINFO 19:16 > > --- > > drivers/usb/dwc3/core.c | 17 +++++++++++++++++ > > drivers/usb/dwc3/core.h | 5 +++++ > > 2 files changed, 22 insertions(+) > > > > diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c index > > 9c6bf054f15d..fc6892c63abf 100644 > > --- a/drivers/usb/dwc3/core.c > > +++ b/drivers/usb/dwc3/core.c > > @@ -23,6 +23,7 @@ > > #include <linux/delay.h> > > #include <linux/dma-mapping.h> > > #include <linux/of.h> > > +#include <linux/of_address.h> > > #include <linux/of_graph.h> > > #include <linux/acpi.h> > > #include <linux/pinctrl/consumer.h> > > @@ -559,6 +560,20 @@ static void dwc3_cache_hwparams(struct dwc3 > *dwc) > > parms->hwparams9 = dwc3_readl(dwc->regs, > DWC3_GHWPARAMS9); } > > > > +static void dwc3_config_soc_bus(struct dwc3 *dwc) { > > + if (of_dma_is_coherent(dwc->dev->of_node)) { > > + u32 reg; > > + > > + reg = dwc3_readl(dwc->regs, DWC3_GSBUSCFG0); > > + reg |= DWC3_GSBUSCFG0_DATRDREQINFO_MASK | > > + DWC3_GSBUSCFG0_DESRDREQINFO_MASK | > > + DWC3_GSBUSCFG0_DATWRREQINFO_MASK | > > + DWC3_GSBUSCFG0_DESWRREQINFO_MASK; > > + dwc3_writel(dwc->regs, DWC3_GSBUSCFG0, reg); > > + } > > +} > > + > > You're overwriting default values for all platforms. Don't do that. Not every > platform supports this setting. Only apply these specific settings to your > platform. This DWC3_GSBUSCFG0 register is part of the DWC3/Core system. In glue/vendor drivers, I couldn't find a way to access the DWC3/Core access register. Could you please provide a suggestion for the Xilinx glue driver (dwc3/dwc3-xilinx.c) to access dwc3 registers? > > BR, > Thinh > > > static int dwc3_core_ulpi_init(struct dwc3 *dwc) { > > int intf; > > @@ -1137,6 +1152,8 @@ static int dwc3_core_init(struct dwc3 *dwc) > > > > dwc3_set_incr_burst_type(dwc); > > > > + dwc3_config_soc_bus(dwc); > > + > > ret = dwc3_phy_power_on(dwc); > > if (ret) > > goto err_exit_phy; > > diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h index > > a69ac67d89fe..bd937025ce05 100644 > > --- a/drivers/usb/dwc3/core.h > > +++ b/drivers/usb/dwc3/core.h > > @@ -173,6 +173,11 @@ > > #define DWC3_OSTS 0xcc10 > > > > /* Bit fields */ > > +/* Global SoC Bus Configuration Register: AHB-prot/AXI-cache/OCP-ReqInfo > */ > > +#define DWC3_GSBUSCFG0_DATRDREQINFO_MASK GENMASK(31, 28) > > +#define DWC3_GSBUSCFG0_DESRDREQINFO_MASK GENMASK(27, 24) > > +#define DWC3_GSBUSCFG0_DATWRREQINFO_MASK GENMASK(23, 20) > > +#define DWC3_GSBUSCFG0_DESWRREQINFO_MASK GENMASK(19, 16) > > > > /* Global SoC Bus Configuration INCRx Register 0 */ > > #define DWC3_GSBUSCFG0_INCR256BRSTENA (1 << 7) /* INCR256 burst */ > > -- > > 2.17.1 > > PM ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] usb: dwc3: core: enable CCI support 2023-11-06 13:48 ` Mehta, Piyush @ 2023-11-10 2:37 ` Thinh Nguyen 2023-11-17 5:44 ` Mehta, Piyush 0 siblings, 1 reply; 6+ messages in thread From: Thinh Nguyen @ 2023-11-10 2:37 UTC (permalink / raw) To: Mehta, Piyush Cc: Thinh Nguyen, gregkh, Simek, Michal, linux-usb, linux-kernel, Paladugu, Siva Durga Prasad, Pandey, Radhey Shyam On Mon, Nov 06, 2023, Mehta, Piyush wrote: > Hi Thinh, > > > -----Original Message----- > > From: Thinh Nguyen <Thinh.Nguyen@synopsys.com> > > Sent: Saturday, October 21, 2023 4:46 AM > > To: Mehta, Piyush <piyush.mehta@amd.com> > > Cc: gregkh@linuxfoundation.org; Simek, Michal <michal.simek@amd.com>; > > Thinh Nguyen <Thinh.Nguyen@synopsys.com>; linux-usb@vger.kernel.org; > > linux-kernel@vger.kernel.org; git (AMD-Xilinx) <git@amd.com> > > Subject: Re: [PATCH] usb: dwc3: core: enable CCI support > > > > On Fri, Oct 13, 2023, Piyush Mehta wrote: > > > The GSBUSCFG0 register bits [31:16] are used to configure the cache > > > type settings of the descriptor and data write/read transfers > > > (Cacheable, Bufferable/ Posted). When CCI is enabled in the design, > > > DWC3 core GSBUSCFG0 cache bits must be updated to support CCI enabled > > transfers in USB. > > > > > > Signed-off-by: Piyush Mehta <piyush.mehta@amd.com> > > > --- > > > DWC3 Register Map Link: > > > https://urldefense.com/v3/__https://docs.xilinx.com/r/en-US/ug1087-zynq- > > ultrascale-registers/GSBUSCFG0-USB3_XHCI- > > Register__;!!A4F2R9G_pg!cbLbYLk9xu54DZMkiTQzMhdCaPA4gmIVInes4ZeNb28 > > AI2pgesEvHNYtjoZfWvE_t7wlUdZvYn-Pio8WjA55ekal$ > > > Register Name GSBUSCFG0 > > > Description Global SoC Bus Configuration Register 0 > > > > > > GSBUSCFG0 (USB3_XHCI) Register Bit-Field: > > > DATRDREQINFO 31:28 > > > DESRDREQINFO 27:24 > > > DATWRREQINFO 23:20 > > > DESWRREQINFO 19:16 > > > --- > > > drivers/usb/dwc3/core.c | 17 +++++++++++++++++ > > > drivers/usb/dwc3/core.h | 5 +++++ > > > 2 files changed, 22 insertions(+) > > > > > > diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c index > > > 9c6bf054f15d..fc6892c63abf 100644 > > > --- a/drivers/usb/dwc3/core.c > > > +++ b/drivers/usb/dwc3/core.c > > > @@ -23,6 +23,7 @@ > > > #include <linux/delay.h> > > > #include <linux/dma-mapping.h> > > > #include <linux/of.h> > > > +#include <linux/of_address.h> > > > #include <linux/of_graph.h> > > > #include <linux/acpi.h> > > > #include <linux/pinctrl/consumer.h> > > > @@ -559,6 +560,20 @@ static void dwc3_cache_hwparams(struct dwc3 > > *dwc) > > > parms->hwparams9 = dwc3_readl(dwc->regs, > > DWC3_GHWPARAMS9); } > > > > > > +static void dwc3_config_soc_bus(struct dwc3 *dwc) { > > > + if (of_dma_is_coherent(dwc->dev->of_node)) { > > > + u32 reg; > > > + > > > + reg = dwc3_readl(dwc->regs, DWC3_GSBUSCFG0); > > > + reg |= DWC3_GSBUSCFG0_DATRDREQINFO_MASK | > > > + DWC3_GSBUSCFG0_DESRDREQINFO_MASK | > > > + DWC3_GSBUSCFG0_DATWRREQINFO_MASK | > > > + DWC3_GSBUSCFG0_DESWRREQINFO_MASK; > > > + dwc3_writel(dwc->regs, DWC3_GSBUSCFG0, reg); > > > + } > > > +} > > > + > > > > You're overwriting default values for all platforms. Don't do that. Not every > > platform supports this setting. Only apply these specific settings to your > > platform. > > This DWC3_GSBUSCFG0 register is part of the DWC3/Core system. In glue/vendor drivers, I couldn't find a way to access > the DWC3/Core access register. Could you please provide a suggestion for the Xilinx glue driver (dwc3/dwc3-xilinx.c) to > access dwc3 registers? We may need to pass the hardware configuration from the dt binding. Thanks, Thinh ^ permalink raw reply [flat|nested] 6+ messages in thread
* RE: [PATCH] usb: dwc3: core: enable CCI support 2023-11-10 2:37 ` Thinh Nguyen @ 2023-11-17 5:44 ` Mehta, Piyush 2024-02-23 22:47 ` Thinh Nguyen 0 siblings, 1 reply; 6+ messages in thread From: Mehta, Piyush @ 2023-11-17 5:44 UTC (permalink / raw) To: Thinh Nguyen Cc: gregkh, Simek, Michal, linux-usb, linux-kernel, Paladugu, Siva Durga Prasad, Pandey, Radhey Shyam Hi, > -----Original Message----- > From: Thinh Nguyen <Thinh.Nguyen@synopsys.com> > Sent: Friday, November 10, 2023 8:07 AM > To: Mehta, Piyush <piyush.mehta@amd.com> > Cc: Thinh Nguyen <Thinh.Nguyen@synopsys.com>; > gregkh@linuxfoundation.org; Simek, Michal <michal.simek@amd.com>; linux- > usb@vger.kernel.org; linux-kernel@vger.kernel.org; Paladugu, Siva Durga Prasad > <siva.durga.prasad.paladugu@amd.com>; Pandey, Radhey Shyam > <radhey.shyam.pandey@amd.com> > Subject: Re: [PATCH] usb: dwc3: core: enable CCI support > > On Mon, Nov 06, 2023, Mehta, Piyush wrote: > > Hi Thinh, > > > > > -----Original Message----- > > > From: Thinh Nguyen <Thinh.Nguyen@synopsys.com> > > > Sent: Saturday, October 21, 2023 4:46 AM > > > To: Mehta, Piyush <piyush.mehta@amd.com> > > > Cc: gregkh@linuxfoundation.org; Simek, Michal > > > <michal.simek@amd.com>; Thinh Nguyen <Thinh.Nguyen@synopsys.com>; > > > linux-usb@vger.kernel.org; linux-kernel@vger.kernel.org; git > > > (AMD-Xilinx) <git@amd.com> > > > Subject: Re: [PATCH] usb: dwc3: core: enable CCI support > > > > > > On Fri, Oct 13, 2023, Piyush Mehta wrote: > > > > The GSBUSCFG0 register bits [31:16] are used to configure the > > > > cache type settings of the descriptor and data write/read > > > > transfers (Cacheable, Bufferable/ Posted). When CCI is enabled in > > > > the design, > > > > DWC3 core GSBUSCFG0 cache bits must be updated to support CCI > > > > enabled > > > transfers in USB. > > > > > > > > Signed-off-by: Piyush Mehta <piyush.mehta@amd.com> > > > > --- > > > > DWC3 Register Map Link: > > > > https://urldefense.com/v3/__https://docs.xilinx.com/r/en-US/ug1087 > > > > -zynq- > > > ultrascale-registers/GSBUSCFG0-USB3_XHCI- > > > > Register__;!!A4F2R9G_pg!cbLbYLk9xu54DZMkiTQzMhdCaPA4gmIVInes4ZeNb28 > > > AI2pgesEvHNYtjoZfWvE_t7wlUdZvYn-Pio8WjA55ekal$ > > > > Register Name GSBUSCFG0 > > > > Description Global SoC Bus Configuration Register 0 > > > > > > > > GSBUSCFG0 (USB3_XHCI) Register Bit-Field: > > > > DATRDREQINFO 31:28 > > > > DESRDREQINFO 27:24 > > > > DATWRREQINFO 23:20 > > > > DESWRREQINFO 19:16 > > > > --- > > > > drivers/usb/dwc3/core.c | 17 +++++++++++++++++ > > > > drivers/usb/dwc3/core.h | 5 +++++ > > > > 2 files changed, 22 insertions(+) > > > > > > > > diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c > > > > index 9c6bf054f15d..fc6892c63abf 100644 > > > > --- a/drivers/usb/dwc3/core.c > > > > +++ b/drivers/usb/dwc3/core.c > > > > @@ -23,6 +23,7 @@ > > > > #include <linux/delay.h> > > > > #include <linux/dma-mapping.h> > > > > #include <linux/of.h> > > > > +#include <linux/of_address.h> > > > > #include <linux/of_graph.h> > > > > #include <linux/acpi.h> > > > > #include <linux/pinctrl/consumer.h> @@ -559,6 +560,20 @@ static > > > > void dwc3_cache_hwparams(struct dwc3 > > > *dwc) > > > > parms->hwparams9 = dwc3_readl(dwc->regs, > > > DWC3_GHWPARAMS9); } > > > > > > > > +static void dwc3_config_soc_bus(struct dwc3 *dwc) { > > > > + if (of_dma_is_coherent(dwc->dev->of_node)) { > > > > + u32 reg; > > > > + > > > > + reg = dwc3_readl(dwc->regs, DWC3_GSBUSCFG0); > > > > + reg |= DWC3_GSBUSCFG0_DATRDREQINFO_MASK | > > > > + DWC3_GSBUSCFG0_DESRDREQINFO_MASK | > > > > + DWC3_GSBUSCFG0_DATWRREQINFO_MASK | > > > > + DWC3_GSBUSCFG0_DESWRREQINFO_MASK; > > > > + dwc3_writel(dwc->regs, DWC3_GSBUSCFG0, reg); > > > > + } > > > > +} > > > > + > > > > > > You're overwriting default values for all platforms. Don't do that. > > > Not every platform supports this setting. Only apply these specific > > > settings to your platform. > > > > This DWC3_GSBUSCFG0 register is part of the DWC3/Core system. In > > glue/vendor drivers, I couldn't find a way to access the DWC3/Core > > access register. Could you please provide a suggestion for the Xilinx glue > driver (dwc3/dwc3-xilinx.c) to access dwc3 registers? > > We may need to pass the hardware configuration from the dt binding. DWC3_GSBUSCFG0 register is implementation defined and part of DWC3/Core (Databook 2.90). Below is example code to make this logic platform specific. It conditionally validates the dma-coherent property and only performs DWC3_GSBUSCFG0 configuration for AMD/Xilinx platform. (DT compatible "xlnx,zynqmp-dwc3"). Example Code: if (of_dma_is_coherent(dwc->dev->of_node) && of_device_is_compatible(dwc->dev->parent->of_node, "xlnx,zynqmp-dwc3")) { u32 reg; reg = dwc3_readl(dwc->regs, DWC3_GSBUSCFG0); reg |= DWC3_GSBUSCFG0_DATRDREQINFO | DWC3_GSBUSCFG0_DESRDREQINFO | DWC3_GSBUSCFG0_DATWRREQINFO | DWC3_GSBUSCFG0_DESWRREQINFO; dwc3_writel(dwc->regs, DWC3_GSBUSCFG0, reg); } > > Thanks, > Thinh ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] usb: dwc3: core: enable CCI support 2023-11-17 5:44 ` Mehta, Piyush @ 2024-02-23 22:47 ` Thinh Nguyen 0 siblings, 0 replies; 6+ messages in thread From: Thinh Nguyen @ 2024-02-23 22:47 UTC (permalink / raw) To: Mehta, Piyush Cc: Thinh Nguyen, gregkh, Simek, Michal, linux-usb, linux-kernel, Paladugu, Siva Durga Prasad, Pandey, Radhey Shyam On Fri, Nov 17, 2023, Mehta, Piyush wrote: > Hi, > > > -----Original Message----- > > From: Thinh Nguyen <Thinh.Nguyen@synopsys.com> > > Sent: Friday, November 10, 2023 8:07 AM > > To: Mehta, Piyush <piyush.mehta@amd.com> > > Cc: Thinh Nguyen <Thinh.Nguyen@synopsys.com>; > > gregkh@linuxfoundation.org; Simek, Michal <michal.simek@amd.com>; linux- > > usb@vger.kernel.org; linux-kernel@vger.kernel.org; Paladugu, Siva Durga Prasad > > <siva.durga.prasad.paladugu@amd.com>; Pandey, Radhey Shyam > > <radhey.shyam.pandey@amd.com> > > Subject: Re: [PATCH] usb: dwc3: core: enable CCI support > > > > On Mon, Nov 06, 2023, Mehta, Piyush wrote: > > > Hi Thinh, > > > > > > > -----Original Message----- > > > > From: Thinh Nguyen <Thinh.Nguyen@synopsys.com> > > > > Sent: Saturday, October 21, 2023 4:46 AM > > > > To: Mehta, Piyush <piyush.mehta@amd.com> > > > > Cc: gregkh@linuxfoundation.org; Simek, Michal > > > > <michal.simek@amd.com>; Thinh Nguyen <Thinh.Nguyen@synopsys.com>; > > > > linux-usb@vger.kernel.org; linux-kernel@vger.kernel.org; git > > > > (AMD-Xilinx) <git@amd.com> > > > > Subject: Re: [PATCH] usb: dwc3: core: enable CCI support > > > > > > > > On Fri, Oct 13, 2023, Piyush Mehta wrote: > > > > > The GSBUSCFG0 register bits [31:16] are used to configure the > > > > > cache type settings of the descriptor and data write/read > > > > > transfers (Cacheable, Bufferable/ Posted). When CCI is enabled in > > > > > the design, > > > > > DWC3 core GSBUSCFG0 cache bits must be updated to support CCI > > > > > enabled > > > > transfers in USB. > > > > > > > > > > Signed-off-by: Piyush Mehta <piyush.mehta@amd.com> > > > > > --- > > > > > DWC3 Register Map Link: > > > > > https://urldefense.com/v3/__https://docs.xilinx.com/r/en-US/ug1087 > > > > > -zynq- > > > > ultrascale-registers/GSBUSCFG0-USB3_XHCI- > > > > > > Register__;!!A4F2R9G_pg!cbLbYLk9xu54DZMkiTQzMhdCaPA4gmIVInes4ZeNb28 > > > > AI2pgesEvHNYtjoZfWvE_t7wlUdZvYn-Pio8WjA55ekal$ > > > > > Register Name GSBUSCFG0 > > > > > Description Global SoC Bus Configuration Register 0 > > > > > > > > > > GSBUSCFG0 (USB3_XHCI) Register Bit-Field: > > > > > DATRDREQINFO 31:28 > > > > > DESRDREQINFO 27:24 > > > > > DATWRREQINFO 23:20 > > > > > DESWRREQINFO 19:16 > > > > > --- > > > > > drivers/usb/dwc3/core.c | 17 +++++++++++++++++ > > > > > drivers/usb/dwc3/core.h | 5 +++++ > > > > > 2 files changed, 22 insertions(+) > > > > > > > > > > diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c > > > > > index 9c6bf054f15d..fc6892c63abf 100644 > > > > > --- a/drivers/usb/dwc3/core.c > > > > > +++ b/drivers/usb/dwc3/core.c > > > > > @@ -23,6 +23,7 @@ > > > > > #include <linux/delay.h> > > > > > #include <linux/dma-mapping.h> > > > > > #include <linux/of.h> > > > > > +#include <linux/of_address.h> > > > > > #include <linux/of_graph.h> > > > > > #include <linux/acpi.h> > > > > > #include <linux/pinctrl/consumer.h> @@ -559,6 +560,20 @@ static > > > > > void dwc3_cache_hwparams(struct dwc3 > > > > *dwc) > > > > > parms->hwparams9 = dwc3_readl(dwc->regs, > > > > DWC3_GHWPARAMS9); } > > > > > > > > > > +static void dwc3_config_soc_bus(struct dwc3 *dwc) { > > > > > + if (of_dma_is_coherent(dwc->dev->of_node)) { > > > > > + u32 reg; > > > > > + > > > > > + reg = dwc3_readl(dwc->regs, DWC3_GSBUSCFG0); > > > > > + reg |= DWC3_GSBUSCFG0_DATRDREQINFO_MASK | > > > > > + DWC3_GSBUSCFG0_DESRDREQINFO_MASK | > > > > > + DWC3_GSBUSCFG0_DATWRREQINFO_MASK | > > > > > + DWC3_GSBUSCFG0_DESWRREQINFO_MASK; > > > > > + dwc3_writel(dwc->regs, DWC3_GSBUSCFG0, reg); > > > > > + } > > > > > +} > > > > > + > > > > > > > > You're overwriting default values for all platforms. Don't do that. > > > > Not every platform supports this setting. Only apply these specific > > > > settings to your platform. > > > > > > This DWC3_GSBUSCFG0 register is part of the DWC3/Core system. In > > > glue/vendor drivers, I couldn't find a way to access the DWC3/Core > > > access register. Could you please provide a suggestion for the Xilinx glue > > driver (dwc3/dwc3-xilinx.c) to access dwc3 registers? > > > > We may need to pass the hardware configuration from the dt binding. > > DWC3_GSBUSCFG0 register is implementation defined and part of DWC3/Core (Databook 2.90). Below is example code > to make this logic platform specific. It conditionally validates the dma-coherent property and only performs > DWC3_GSBUSCFG0 configuration for AMD/Xilinx platform. (DT compatible "xlnx,zynqmp-dwc3"). > > Example Code: > if (of_dma_is_coherent(dwc->dev->of_node) && of_device_is_compatible(dwc->dev->parent->of_node, "xlnx,zynqmp-dwc3")) { > u32 reg; > > reg = dwc3_readl(dwc->regs, DWC3_GSBUSCFG0); > reg |= DWC3_GSBUSCFG0_DATRDREQINFO | > DWC3_GSBUSCFG0_DESRDREQINFO | > DWC3_GSBUSCFG0_DATWRREQINFO | > DWC3_GSBUSCFG0_DESWRREQINFO; > dwc3_writel(dwc->regs, DWC3_GSBUSCFG0, reg); > } I just realized I missed this in the inbox after your latest patch. Sorry for the delay response. Since this is platform specific, can we do this in your glue driver? Split and share some of the defined register definitions from core.h to regs.h. You can temporarily memory map and update this register in your Xilinx glue driver. Its value should retain after soft reset. Thanks, Thinh ^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2024-02-23 22:47 UTC | newest] Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2023-10-13 5:34 [PATCH] usb: dwc3: core: enable CCI support Piyush Mehta 2023-10-20 23:16 ` Thinh Nguyen 2023-11-06 13:48 ` Mehta, Piyush 2023-11-10 2:37 ` Thinh Nguyen 2023-11-17 5:44 ` Mehta, Piyush 2024-02-23 22:47 ` Thinh Nguyen
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®