[PATCH 1/2] arm64: dts: ti: k3-am65: Enable SDHCI nodes at the board level

[PATCH 1/2] arm64: dts: ti: k3-am65: Enable SDHCI nodes at the board level

[Andrew Davis]

SDHCI nodes defined in the top-level AM65 SoC dtsi files are incomplete
and will not be functional unless they are extended.

As the attached SD/eMMC is only known about at the board integration level,
these nodes should only be enabled when provided with this information.

Disable the SDHCI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.

Signed-off-by: Andrew Davis <afd@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi           | 1 +
 arch/arm64/boot/dts/ti/k3-am65-main.dtsi                     | 2 ++
 arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-common.dtsi   | 5 -----
 arch/arm64/boot/dts/ti/k3-am654-base-board.dts               | 2 ++
 .../arm64/boot/dts/ti/k3-am6548-iot2050-advanced-common.dtsi | 1 +
 5 files changed, 6 insertions(+), 5 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
index ba1c14a54acf4..79dbb286bafc1 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
@@ -554,6 +554,7 @@ &ecap0 {
 };
 
 &sdhci1 {
+	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_mmc1_pins_default>;
 	ti,driver-strength-ohm = <50>;
diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
index 5ebb87f467de5..9ff3094743f21 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
@@ -449,6 +449,7 @@ sdhci0: mmc@4f80000 {
 		ti,otap-del-sel-hs400 = <0x0>;
 		ti,trm-icp = <0x8>;
 		dma-coherent;
+		status = "disabled";
 	};
 
 	sdhci1: mmc@4fa0000 {
@@ -471,6 +472,7 @@ sdhci1: mmc@4fa0000 {
 		ti,clkbuf-sel = <0x7>;
 		ti,trm-icp = <0x8>;
 		dma-coherent;
+		status = "disabled";
 	};
 
 	scm_conf: scm-conf@100000 {
diff --git a/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-common.dtsi b/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-common.dtsi
index 5ab434c02ab6b..e4d7cba7c62f0 100644
--- a/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-common.dtsi
@@ -29,11 +29,6 @@ cpu-map {
 	/delete-node/ l2-cache1;
 };
 
-/* eMMC */
-&sdhci0 {
-	status = "disabled";
-};
-
 &main_pmx0 {
 	main_uart0_pins_default: main-uart0-default-pins {
 		pinctrl-single,pins = <
diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
index 1637ec5ab5eda..822c288d27976 100644
--- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
@@ -449,6 +449,7 @@ flash@0 {
 };
 
 &sdhci0 {
+	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_mmc0_pins_default>;
 	bus-width = <8>;
@@ -463,6 +464,7 @@ &sdhci0 {
  * disable sdhci1
  */
 &sdhci1 {
+	status = "okay";
 	vmmc-supply = <&vdd_mmc1_sd>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_mmc1_pins_default>;
diff --git a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-common.dtsi b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-common.dtsi
index be55494b1f3fc..a847209c3df52 100644
--- a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-common.dtsi
@@ -43,6 +43,7 @@ AM65X_IOPAD(0x01b0, PIN_INPUT,          0)  /* (C25) MMC0_DS */
 
 /* eMMC */
 &sdhci0 {
+	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_mmc0_pins_default>;
 	bus-width = <8>;
-- 
2.39.2

[PATCH 2/2] arm64: dts: ti: k3-am64: Enable SDHCI nodes at the board level

[Andrew Davis]

SDHCI nodes defined in the top-level AM64 SoC dtsi files are incomplete
and will not be functional unless they are extended.

As the attached SD/eMMC is only known about at the board integration level,
these nodes should only be enabled when provided with this information.

Disable the SDHCI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.

Signed-off-by: Andrew Davis <afd@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am64-main.dtsi                 | 2 ++
 arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi          | 1 +
 arch/arm64/boot/dts/ti/k3-am642-evm.dts                  | 6 ++++--
 arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-rdk.dts | 1 +
 arch/arm64/boot/dts/ti/k3-am642-sk.dts                   | 4 +++-
 arch/arm64/boot/dts/ti/k3-am642-tqma64xxl-mbax4xxl.dts   | 1 -
 arch/arm64/boot/dts/ti/k3-am642-tqma64xxl.dtsi           | 1 +
 7 files changed, 12 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am64-main.dtsi b/arch/arm64/boot/dts/ti/k3-am64-main.dtsi
index 0be642bc1b86d..c3300c36fdbcb 100644
--- a/arch/arm64/boot/dts/ti/k3-am64-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am64-main.dtsi
@@ -623,6 +623,7 @@ sdhci0: mmc@fa10000 {
 		ti,otap-del-sel-mmc-hs = <0x0>;
 		ti,otap-del-sel-ddr52 = <0x6>;
 		ti,otap-del-sel-hs200 = <0x7>;
+		status = "disabled";
 	};
 
 	sdhci1: mmc@fa00000 {
@@ -641,6 +642,7 @@ sdhci1: mmc@fa00000 {
 		ti,otap-del-sel-sdr104 = <0x6>;
 		ti,otap-del-sel-ddr50 = <0x9>;
 		ti,clkbuf-sel = <0x7>;
+		status = "disabled";
 	};
 
 	cpsw3g: ethernet@8000000 {
diff --git a/arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi b/arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi
index f87f09d83c956..b8f844f667afc 100644
--- a/arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi
@@ -211,6 +211,7 @@ flash@0 {
 };
 
 &sdhci0 {
+	status = "okay";
 	bus-width = <8>;
 	non-removable;
 	ti,driver-strength-ohm = <50>;
diff --git a/arch/arm64/boot/dts/ti/k3-am642-evm.dts b/arch/arm64/boot/dts/ti/k3-am642-evm.dts
index 4dba18941015d..256606be56fef 100644
--- a/arch/arm64/boot/dts/ti/k3-am642-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-am642-evm.dts
@@ -487,17 +487,19 @@ eeprom@0 {
 	};
 };
 
+/* eMMC */
 &sdhci0 {
-	/* emmc */
+	status = "okay";
 	bus-width = <8>;
 	non-removable;
 	ti,driver-strength-ohm = <50>;
 	disable-wp;
 };
 
+/* SD/MMC */
 &sdhci1 {
-	/* SD/MMC */
 	bootph-all;
+	status = "okay";
 	vmmc-supply = <&vdd_mmc1>;
 	pinctrl-names = "default";
 	bus-width = <4>;
diff --git a/arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-rdk.dts b/arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-rdk.dts
index 9175e96842d82..53b64e55413f9 100644
--- a/arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-rdk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-rdk.dts
@@ -264,6 +264,7 @@ &main_uart1 {
 };
 
 &sdhci1 {
+	status = "okay";
 	vmmc-supply = <&vcc_3v3_mmc>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_mmc1_pins_default>;
diff --git a/arch/arm64/boot/dts/ti/k3-am642-sk.dts b/arch/arm64/boot/dts/ti/k3-am642-sk.dts
index f29c8a9b59ba7..bffbd234f715a 100644
--- a/arch/arm64/boot/dts/ti/k3-am642-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am642-sk.dts
@@ -439,6 +439,7 @@ &mcu_gpio0 {
 };
 
 &sdhci0 {
+	status = "okay";
 	vmmc-supply = <&wlan_en>;
 	bus-width = <4>;
 	non-removable;
@@ -458,9 +459,10 @@ wlcore: wlcore@2 {
 	};
 };
 
+/* SD/MMC */
 &sdhci1 {
-	/* SD/MMC */
 	bootph-all;
+	status = "okay";
 	vmmc-supply = <&vdd_mmc1>;
 	pinctrl-names = "default";
 	bus-width = <4>;
diff --git a/arch/arm64/boot/dts/ti/k3-am642-tqma64xxl-mbax4xxl.dts b/arch/arm64/boot/dts/ti/k3-am642-tqma64xxl-mbax4xxl.dts
index d95d80076a427..55102d35cecc1 100644
--- a/arch/arm64/boot/dts/ti/k3-am642-tqma64xxl-mbax4xxl.dts
+++ b/arch/arm64/boot/dts/ti/k3-am642-tqma64xxl-mbax4xxl.dts
@@ -425,7 +425,6 @@ &sdhci1 {
 	ti,driver-strength-ohm = <50>;
 	ti,fails-without-test-cd;
 	/* Enabled by overlay */
-	status = "disabled";
 };
 
 &tscadc0 {
diff --git a/arch/arm64/boot/dts/ti/k3-am642-tqma64xxl.dtsi b/arch/arm64/boot/dts/ti/k3-am642-tqma64xxl.dtsi
index d82d4a98306a7..6c785eff7d2ff 100644
--- a/arch/arm64/boot/dts/ti/k3-am642-tqma64xxl.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am642-tqma64xxl.dtsi
@@ -219,6 +219,7 @@ partitions {
 };
 
 &sdhci0 {
+	status = "okay";
 	non-removable;
 	disable-wp;
 	no-sdio;
-- 
2.39.2

Re: [PATCH 1/2] arm64: dts: ti: k3-am65: Enable SDHCI nodes at the board level

[Nishanth Menon]

Hi Andrew Davis,

On Fri, 17 Nov 2023 10:33:38 -0600, Andrew Davis wrote:
> SDHCI nodes defined in the top-level AM65 SoC dtsi files are incomplete
> and will not be functional unless they are extended.
> 
> As the attached SD/eMMC is only known about at the board integration level,
> these nodes should only be enabled when provided with this information.
> 
> Disable the SDHCI nodes in the dtsi files and only enable the ones that
> are actually pinned out on a given board.
> 
> [...]

I have applied the following to branch ti-k3-dts-next on [1].
Thank you!

[1/2] arm64: dts: ti: k3-am65: Enable SDHCI nodes at the board level
      commit: 006d93519db2e0eacbaeac20cf9d55a4d842a006
[2/2] arm64: dts: ti: k3-am64: Enable SDHCI nodes at the board level
      commit: 3b6345e3fcf4c93a79f396121cd0e6f98f04da13

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent up the chain during
the next merge window (or sooner if it is a relevant bug fix), however if
problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux.git
-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D