* [PATCH 0/2] Add CAN and OSPI support for AM69-SK platform @ 2024-01-18 15:35 sabiya.d 2024-01-18 15:35 ` [PATCH 1/2] arm64: dts: ti: k3-am69-sk: Enable CAN interfaces for AM69 SK board sabiya.d 2024-01-18 15:35 ` [PATCH 2/2] arm64: dts: ti: k3-am69-sk: Add support for OSPI flash sabiya.d 0 siblings, 2 replies; 5+ messages in thread From: sabiya.d @ 2024-01-18 15:35 UTC (permalink / raw) To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt, linus.walleij Cc: devicetree, linux-arm-kernel, linux-kernel, u-kumar1, sabiya.d, Dasnavis Sabiya From: Dasnavis Sabiya <sabiya.d@ti.com> Hi All, This series adds support for the below interfaces on AM69-SK platform: - CAN support on both MCU and MAIN domains - OSPI NOR flash support Dasnavis Sabiya (2): arm64: dts: ti: k3-am69-sk: Enable CAN interfaces for AM69 SK board arm64: dts: ti: k3-am69-sk: Add support for OSPI flash arch/arm64/boot/dts/ti/k3-am69-sk.dts | 166 ++++++++++++++++++++++++++ 1 file changed, 166 insertions(+) -- 2.34.1 ^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH 1/2] arm64: dts: ti: k3-am69-sk: Enable CAN interfaces for AM69 SK board 2024-01-18 15:35 [PATCH 0/2] Add CAN and OSPI support for AM69-SK platform sabiya.d @ 2024-01-18 15:35 ` sabiya.d 2024-01-19 13:20 ` Kumar, Udit 2024-01-18 15:35 ` [PATCH 2/2] arm64: dts: ti: k3-am69-sk: Add support for OSPI flash sabiya.d 1 sibling, 1 reply; 5+ messages in thread From: sabiya.d @ 2024-01-18 15:35 UTC (permalink / raw) To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt, linus.walleij Cc: devicetree, linux-arm-kernel, linux-kernel, u-kumar1, sabiya.d, Dasnavis Sabiya From: Dasnavis Sabiya <sabiya.d@ti.com> AM69 SK board has several CAN bus interfaces on both MCU and MAIN domains. This enables the CAN interfaces on MCU and MAIN domain. Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com> --- arch/arm64/boot/dts/ti/k3-am69-sk.dts | 85 +++++++++++++++++++++++++++ 1 file changed, 85 insertions(+) diff --git a/arch/arm64/boot/dts/ti/k3-am69-sk.dts b/arch/arm64/boot/dts/ti/k3-am69-sk.dts index 370980eb59b0..feb571a5a0f5 100644 --- a/arch/arm64/boot/dts/ti/k3-am69-sk.dts +++ b/arch/arm64/boot/dts/ti/k3-am69-sk.dts @@ -29,6 +29,10 @@ aliases { i2c0 = &wkup_i2c0; i2c3 = &main_i2c0; ethernet0 = &mcu_cpsw_port1; + can0 = &mcu_mcan0; + can1 = &mcu_mcan1; + can2 = &main_mcan6; + can3 = &main_mcan7; }; memory@80000000 { @@ -321,6 +325,31 @@ tfp410_out: endpoint { }; }; }; + + transceiver1: can-phy0 { + compatible = "ti,tcan1042"; + #phy-cells = <0>; + max-bitrate = <5000000>; + }; + + transceiver2: can-phy1 { + compatible = "ti,tcan1042"; + #phy-cells = <0>; + max-bitrate = <5000000>; + }; + + transceiver3: can-phy2 { + compatible = "ti,tcan1042"; + #phy-cells = <0>; + max-bitrate = <5000000>; + }; + + transceiver4: can-phy3 { + compatible = "ti,tcan1042"; + #phy-cells = <0>; + max-bitrate = <5000000>; + }; + }; &main_pmx0 { @@ -429,6 +458,20 @@ hdmi_hpd_pins_default: hdmi-hpd-default-pins { J784S4_IOPAD(0x000, PIN_INPUT, 7) /* (AN35) EXTINTN.GPIO0_0 */ >; }; + + main_mcan6_pins_default: main-mcan6-default-pins { + pinctrl-single,pins = < + J784S4_IOPAD(0x098, PIN_INPUT, 0) /* (AH36) MCAN6_RX */ + J784S4_IOPAD(0x094, PIN_OUTPUT, 0) /* (AG35) MCAN6_TX */ + >; + }; + + main_mcan7_pins_default: main-mcan7-default-pins { + pinctrl-single,pins = < + J784S4_IOPAD(0x0A0, PIN_INPUT, 0) /* (AD34) MCAN7_RX */ + J784S4_IOPAD(0x09C, PIN_OUTPUT, 0) /* (AF35) MCAN7_TX */ + >; + }; }; &wkup_pmx2 { @@ -525,6 +568,20 @@ hdmi_pdn_pins_default: hdmi-pdn-default-pins { J784S4_WKUP_IOPAD(0x090, PIN_INPUT, 7) /* (H37) WKUP_GPIO0_14 */ >; }; + + mcu_mcan0_pins_default: mcu-mcan0-default-pins { + pinctrl-single,pins = < + J784S4_WKUP_IOPAD(0x054, PIN_INPUT, 0) /* (F38) MCU_MCAN0_RX */ + J784S4_WKUP_IOPAD(0x050, PIN_OUTPUT, 0) /* (K33) MCU_MCAN0_TX */ + >; + }; + + mcu_mcan1_pins_default: mcu-mcan1-default-pins { + pinctrl-single,pins = < + J784S4_WKUP_IOPAD(0x06c, PIN_INPUT, 0) /* (K36) WKUP_GPIO0_5.MCU_MCAN1_RX */ + J784S4_WKUP_IOPAD(0x068, PIN_OUTPUT, 0)/* (H35) WKUP_GPIO0_4.MCU_MCAN1_TX */ + >; + }; }; &wkup_pmx3 { @@ -988,3 +1045,31 @@ dp0_out: endpoint { }; }; }; + +&mcu_mcan0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mcu_mcan0_pins_default>; + phys = <&transceiver1>; +}; + +&mcu_mcan1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mcu_mcan1_pins_default>; + phys = <&transceiver2>; +}; + +&main_mcan6 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&main_mcan6_pins_default>; + phys = <&transceiver3>; +}; + +&main_mcan7 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&main_mcan7_pins_default>; + phys = <&transceiver4>; +}; -- 2.34.1 ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH 1/2] arm64: dts: ti: k3-am69-sk: Enable CAN interfaces for AM69 SK board 2024-01-18 15:35 ` [PATCH 1/2] arm64: dts: ti: k3-am69-sk: Enable CAN interfaces for AM69 SK board sabiya.d @ 2024-01-19 13:20 ` Kumar, Udit 0 siblings, 0 replies; 5+ messages in thread From: Kumar, Udit @ 2024-01-19 13:20 UTC (permalink / raw) To: sabiya.d, nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt, linus.walleij Cc: devicetree, linux-arm-kernel, linux-kernel, Dasnavis Sabiya On 1/18/2024 9:05 PM, sabiya.d@mistralsolutions.com wrote: > From: Dasnavis Sabiya <sabiya.d@ti.com> > > AM69 SK board has several CAN bus interfaces on both MCU and MAIN domains. > This enables the CAN interfaces on MCU and MAIN domain. > > Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com> > --- > arch/arm64/boot/dts/ti/k3-am69-sk.dts | 85 +++++++++++++++++++++++++++ > 1 file changed, 85 insertions(+) > > diff --git a/arch/arm64/boot/dts/ti/k3-am69-sk.dts b/arch/arm64/boot/dts/ti/k3-am69-sk.dts > index 370980eb59b0..feb571a5a0f5 100644 > --- a/arch/arm64/boot/dts/ti/k3-am69-sk.dts > +++ b/arch/arm64/boot/dts/ti/k3-am69-sk.dts > @@ -29,6 +29,10 @@ aliases { > i2c0 = &wkup_i2c0; > i2c3 = &main_i2c0; > ethernet0 = &mcu_cpsw_port1; > + can0 = &mcu_mcan0; > + can1 = &mcu_mcan1; > + can2 = &main_mcan6; > + can3 = &main_mcan7; AFAIK, can sub system does not support aliasing. IMO, you can remove these. > }; > > memory@80000000 { > @@ -321,6 +325,31 @@ tfp410_out: endpoint { > }; > }; > }; > + > + transceiver1: can-phy0 { > + compatible = "ti,tcan1042"; > + #phy-cells = <0>; > + max-bitrate = <5000000>; > + }; > + > + transceiver2: can-phy1 { > + compatible = "ti,tcan1042"; > + #phy-cells = <0>; > + max-bitrate = <5000000>; > + }; > + > + transceiver3: can-phy2 { > + compatible = "ti,tcan1042"; > + #phy-cells = <0>; > + max-bitrate = <5000000>; > + }; > + > + transceiver4: can-phy3 { > + compatible = "ti,tcan1042"; > + #phy-cells = <0>; > + max-bitrate = <5000000>; > + }; > + > }; > > &main_pmx0 { > @@ -429,6 +458,20 @@ hdmi_hpd_pins_default: hdmi-hpd-default-pins { > J784S4_IOPAD(0x000, PIN_INPUT, 7) /* (AN35) EXTINTN.GPIO0_0 */ > >; > }; > + > + main_mcan6_pins_default: main-mcan6-default-pins { > + pinctrl-single,pins = < > + J784S4_IOPAD(0x098, PIN_INPUT, 0) /* (AH36) MCAN6_RX */ > + J784S4_IOPAD(0x094, PIN_OUTPUT, 0) /* (AG35) MCAN6_TX */ > + >; > + }; > + > + main_mcan7_pins_default: main-mcan7-default-pins { > + pinctrl-single,pins = < > + J784S4_IOPAD(0x0A0, PIN_INPUT, 0) /* (AD34) MCAN7_RX */ > + J784S4_IOPAD(0x09C, PIN_OUTPUT, 0) /* (AF35) MCAN7_TX */ > + >; > + }; > }; > > &wkup_pmx2 { > @@ -525,6 +568,20 @@ hdmi_pdn_pins_default: hdmi-pdn-default-pins { > J784S4_WKUP_IOPAD(0x090, PIN_INPUT, 7) /* (H37) WKUP_GPIO0_14 */ > >; > }; > + > + mcu_mcan0_pins_default: mcu-mcan0-default-pins { > + pinctrl-single,pins = < > + J784S4_WKUP_IOPAD(0x054, PIN_INPUT, 0) /* (F38) MCU_MCAN0_RX */ > + J784S4_WKUP_IOPAD(0x050, PIN_OUTPUT, 0) /* (K33) MCU_MCAN0_TX */ > + >; > + }; > + > + mcu_mcan1_pins_default: mcu-mcan1-default-pins { > + pinctrl-single,pins = < > + J784S4_WKUP_IOPAD(0x06c, PIN_INPUT, 0) /* (K36) WKUP_GPIO0_5.MCU_MCAN1_RX */ > + J784S4_WKUP_IOPAD(0x068, PIN_OUTPUT, 0)/* (H35) WKUP_GPIO0_4.MCU_MCAN1_TX */ > + >; > + }; > }; > > &wkup_pmx3 { > @@ -988,3 +1045,31 @@ dp0_out: endpoint { > }; > }; > }; > + > +&mcu_mcan0 { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&mcu_mcan0_pins_default>; > + phys = <&transceiver1>; > +}; > + > +&mcu_mcan1 { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&mcu_mcan1_pins_default>; > + phys = <&transceiver2>; > +}; > + > +&main_mcan6 { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&main_mcan6_pins_default>; > + phys = <&transceiver3>; > +}; > + > +&main_mcan7 { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&main_mcan7_pins_default>; > + phys = <&transceiver4>; > +}; ^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH 2/2] arm64: dts: ti: k3-am69-sk: Add support for OSPI flash 2024-01-18 15:35 [PATCH 0/2] Add CAN and OSPI support for AM69-SK platform sabiya.d 2024-01-18 15:35 ` [PATCH 1/2] arm64: dts: ti: k3-am69-sk: Enable CAN interfaces for AM69 SK board sabiya.d @ 2024-01-18 15:35 ` sabiya.d 2024-01-19 13:14 ` Nishanth Menon 1 sibling, 1 reply; 5+ messages in thread From: sabiya.d @ 2024-01-18 15:35 UTC (permalink / raw) To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt, linus.walleij Cc: devicetree, linux-arm-kernel, linux-kernel, u-kumar1, sabiya.d, Dasnavis Sabiya From: Dasnavis Sabiya <sabiya.d@ti.com> AM69 SK has S28HS512T OSPI flash connected to MCU OSPI0. Enable support for the same. Also describe the partition information according to the offsets in the bootloader. Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com> --- arch/arm64/boot/dts/ti/k3-am69-sk.dts | 81 +++++++++++++++++++++++++++ 1 file changed, 81 insertions(+) diff --git a/arch/arm64/boot/dts/ti/k3-am69-sk.dts b/arch/arm64/boot/dts/ti/k3-am69-sk.dts index feb571a5a0f5..f368105942eb 100644 --- a/arch/arm64/boot/dts/ti/k3-am69-sk.dts +++ b/arch/arm64/boot/dts/ti/k3-am69-sk.dts @@ -474,6 +474,25 @@ J784S4_IOPAD(0x09C, PIN_OUTPUT, 0) /* (AF35) MCAN7_TX */ }; }; +&wkup_pmx0 { + bootph-all; + mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins { + pinctrl-single,pins = < + J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (E32) MCU_OSPI0_CLK */ + J784S4_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (A32) MCU_OSPI0_CSn0 */ + J784S4_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (B33) MCU_OSPI0_D0 */ + J784S4_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (B32) MCU_OSPI0_D1 */ + J784S4_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (C33) MCU_OSPI0_D2 */ + J784S4_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (C35) MCU_OSPI0_D3 */ + J784S4_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (D33) MCU_OSPI0_D4 */ + J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (D34) MCU_OSPI0_D5 */ + J784S4_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (E34) MCU_OSPI0_D6 */ + J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (E33) MCU_OSPI0_D7 */ + J784S4_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (C34) MCU_OSPI0_DQS */ + >; + }; +}; + &wkup_pmx2 { bootph-all; pmic_irq_pins_default: pmic-irq-default-pins { @@ -1073,3 +1092,65 @@ &main_mcan7 { pinctrl-0 = <&main_mcan7_pins_default>; phys = <&transceiver4>; }; + +&ospi0 { + bootph-all; + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mcu_fss0_ospi0_pins_default>; + + flash@0 { + bootph-all; + compatible = "jedec,spi-nor"; + reg = <0x0>; + spi-tx-bus-width = <8>; + spi-rx-bus-width = <8>; + spi-max-frequency = <25000000>; + cdns,tshsl-ns = <60>; + cdns,tsd2d-ns = <60>; + cdns,tchsh-ns = <60>; + cdns,tslch-ns = <60>; + cdns,read-delay = <4>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "ospi.tiboot3"; + reg = <0x0 0x80000>; + }; + + partition@80000 { + label = "ospi.tispl"; + reg = <0x80000 0x200000>; + }; + + partition@280000 { + label = "ospi.u-boot"; + reg = <0x280000 0x400000>; + }; + + partition@680000 { + label = "ospi.env"; + reg = <0x680000 0x40000>; + }; + + partition@6c0000 { + label = "ospi.env.backup"; + reg = <0x6c0000 0x40000>; + }; + + partition@800000 { + label = "ospi.rootfs"; + reg = <0x800000 0x37c0000>; + }; + + partition@3fc0000 { + label = "ospi.phypattern"; + reg = <0x3fc0000 0x40000>; + }; + }; + }; +}; -- 2.34.1 ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH 2/2] arm64: dts: ti: k3-am69-sk: Add support for OSPI flash 2024-01-18 15:35 ` [PATCH 2/2] arm64: dts: ti: k3-am69-sk: Add support for OSPI flash sabiya.d @ 2024-01-19 13:14 ` Nishanth Menon 0 siblings, 0 replies; 5+ messages in thread From: Nishanth Menon @ 2024-01-19 13:14 UTC (permalink / raw) To: sabiya.d Cc: vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt, linus.walleij, devicetree, linux-arm-kernel, linux-kernel, u-kumar1, Dasnavis Sabiya On 21:05-20240118, sabiya.d@mistralsolutions.com wrote: > From: Dasnavis Sabiya <sabiya.d@ti.com> > > AM69 SK has S28HS512T OSPI flash connected to MCU OSPI0. > Enable support for the same. Also describe the partition > information according to the offsets in the bootloader. > > Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com> > --- > arch/arm64/boot/dts/ti/k3-am69-sk.dts | 81 +++++++++++++++++++++++++++ > 1 file changed, 81 insertions(+) > > diff --git a/arch/arm64/boot/dts/ti/k3-am69-sk.dts b/arch/arm64/boot/dts/ti/k3-am69-sk.dts > index feb571a5a0f5..f368105942eb 100644 > --- a/arch/arm64/boot/dts/ti/k3-am69-sk.dts > +++ b/arch/arm64/boot/dts/ti/k3-am69-sk.dts > @@ -474,6 +474,25 @@ J784S4_IOPAD(0x09C, PIN_OUTPUT, 0) /* (AF35) MCAN7_TX */ > }; > }; > > +&wkup_pmx0 { > + bootph-all; > + mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins { > + pinctrl-single,pins = < > + J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (E32) MCU_OSPI0_CLK */ > + J784S4_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (A32) MCU_OSPI0_CSn0 */ > + J784S4_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (B33) MCU_OSPI0_D0 */ > + J784S4_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (B32) MCU_OSPI0_D1 */ > + J784S4_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (C33) MCU_OSPI0_D2 */ > + J784S4_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (C35) MCU_OSPI0_D3 */ > + J784S4_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (D33) MCU_OSPI0_D4 */ > + J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (D34) MCU_OSPI0_D5 */ > + J784S4_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (E34) MCU_OSPI0_D6 */ > + J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (E33) MCU_OSPI0_D7 */ > + J784S4_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (C34) MCU_OSPI0_DQS */ > + >; > + }; > +}; > + > &wkup_pmx2 { > bootph-all; > pmic_irq_pins_default: pmic-irq-default-pins { > @@ -1073,3 +1092,65 @@ &main_mcan7 { > pinctrl-0 = <&main_mcan7_pins_default>; > phys = <&transceiver4>; > }; > + > +&ospi0 { > + bootph-all; Only on the leaf nodes please. > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&mcu_fss0_ospi0_pins_default>; > + > + flash@0 { > + bootph-all; > + compatible = "jedec,spi-nor"; > + reg = <0x0>; > + spi-tx-bus-width = <8>; > + spi-rx-bus-width = <8>; > + spi-max-frequency = <25000000>; > + cdns,tshsl-ns = <60>; > + cdns,tsd2d-ns = <60>; > + cdns,tchsh-ns = <60>; > + cdns,tslch-ns = <60>; > + cdns,read-delay = <4>; > + > + partitions { > + compatible = "fixed-partitions"; > + #address-cells = <1>; > + #size-cells = <1>; > + > + partition@0 { > + label = "ospi.tiboot3"; > + reg = <0x0 0x80000>; > + }; > + > + partition@80000 { > + label = "ospi.tispl"; > + reg = <0x80000 0x200000>; > + }; > + > + partition@280000 { > + label = "ospi.u-boot"; > + reg = <0x280000 0x400000>; > + }; > + > + partition@680000 { > + label = "ospi.env"; > + reg = <0x680000 0x40000>; > + }; > + > + partition@6c0000 { > + label = "ospi.env.backup"; > + reg = <0x6c0000 0x40000>; > + }; > + > + partition@800000 { > + label = "ospi.rootfs"; > + reg = <0x800000 0x37c0000>; > + }; > + > + partition@3fc0000 { > + label = "ospi.phypattern"; > + reg = <0x3fc0000 0x40000>; > + }; > + }; > + }; > +}; > -- > 2.34.1 > -- Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D ^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2024-01-19 13:20 UTC | newest] Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2024-01-18 15:35 [PATCH 0/2] Add CAN and OSPI support for AM69-SK platform sabiya.d 2024-01-18 15:35 ` [PATCH 1/2] arm64: dts: ti: k3-am69-sk: Enable CAN interfaces for AM69 SK board sabiya.d 2024-01-19 13:20 ` Kumar, Udit 2024-01-18 15:35 ` [PATCH 2/2] arm64: dts: ti: k3-am69-sk: Add support for OSPI flash sabiya.d 2024-01-19 13:14 ` Nishanth Menon
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®