[PATCH 0/7] can: m_can: Fix polling and other issues

[PATCH 0/7] can: m_can: Fix polling and other issues

[Markus Schneider-Pargmann]

Hi everyone,

these are a number of fixes for m_can that fix polling mode and some
other issues that I saw while working on the code.

Any testing and review is appreciated.

It is currently based on v6.10-rc1 + a patch from Martin, mainly for
review purposes. Once next rc1 is out, I will rebase it, but it should
also apply cleanly.

Best,
Markus

Markus Schneider-Pargmann (7):
  can: m_can: Reset coalescing during suspend/resume
  can: m_can: Remove coalesing disable in isr during suspend
  can: m_can: Remove m_can_rx_peripheral indirection
  can: m_can: Do not cancel timer from within timer
  can: m_can: disable_all_interrupts, not clear active_interrupts
  can: m_can: Reset cached active_interrupts on start
  can: m_can: Limit coalescing to peripheral instances

 drivers/net/can/m_can/m_can.c | 112 ++++++++++++++++++++--------------
 1 file changed, 67 insertions(+), 45 deletions(-)

-- 
2.45.2

[PATCH 1/7] can: m_can: Reset coalescing during suspend/resume

[Markus Schneider-Pargmann]

During resume the interrupts are limited to IR_RF0N and the chip keeps
running. In this case if coalescing is enabled and active we may miss
waterlevel interrupts during suspend. It is safer to reset the
coalescing by stopping the timer and adding IR_RF0N | IR_TEFN to the
interrupts.

This is a theoratical issue and probably extremely rare.

Cc: Martin Hundebøll <martin@geanix.com>
Fixes: 4a94d7e31cf5 ("can: m_can: allow keeping the transceiver running in suspend")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
---
 drivers/net/can/m_can/m_can.c | 16 +++++++++++++---
 1 file changed, 13 insertions(+), 3 deletions(-)

diff --git a/drivers/net/can/m_can/m_can.c b/drivers/net/can/m_can/m_can.c
index 7f63f866083e..9d7d551e3534 100644
--- a/drivers/net/can/m_can/m_can.c
+++ b/drivers/net/can/m_can/m_can.c
@@ -2427,12 +2427,15 @@ int m_can_class_suspend(struct device *dev)
 		netif_device_detach(ndev);
 
 		/* leave the chip running with rx interrupt enabled if it is
-		 * used as a wake-up source.
+		 * used as a wake-up source. Coalescing needs to be reset then,
+		 * the timer is cancelled here, interrupts are done in resume.
 		 */
-		if (cdev->pm_wake_source)
+		if (cdev->pm_wake_source) {
+			hrtimer_cancel(&cdev->hrtimer);
 			m_can_write(cdev, M_CAN_IE, IR_RF0N);
-		else
+		} else {
 			m_can_stop(ndev);
+		}
 
 		m_can_clk_stop(cdev);
 	}
@@ -2462,6 +2465,13 @@ int m_can_class_resume(struct device *dev)
 			return ret;
 
 		if (cdev->pm_wake_source) {
+			/* Restore active interrupts but disable coalescing as
+			 * we may have missed important waterlevel interrupts
+			 * between suspend and resume. Timers are already
+			 * stopped in suspend. Here we enable all interrupts
+			 * again.
+			 */
+			cdev->active_interrupts |= IR_RF0N | IR_TEFN;
 			m_can_write(cdev, M_CAN_IE, cdev->active_interrupts);
 		} else {
 			ret  = m_can_start(ndev);
-- 
2.45.2

[PATCH 2/7] can: m_can: Remove coalesing disable in isr during suspend

[Markus Schneider-Pargmann]

We don't need to disable coalescing when the interrupt handler executes
while the chip is suspended. The coalescing is already reset during
suspend.

Fixes: 07f25091ca02 ("can: m_can: Implement receive coalescing")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
---
 drivers/net/can/m_can/m_can.c | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)

diff --git a/drivers/net/can/m_can/m_can.c b/drivers/net/can/m_can/m_can.c
index 9d7d551e3534..fd600ab93218 100644
--- a/drivers/net/can/m_can/m_can.c
+++ b/drivers/net/can/m_can/m_can.c
@@ -1223,10 +1223,8 @@ static irqreturn_t m_can_isr(int irq, void *dev_id)
 	struct m_can_classdev *cdev = netdev_priv(dev);
 	u32 ir;
 
-	if (pm_runtime_suspended(cdev->dev)) {
-		m_can_coalescing_disable(cdev);
+	if (pm_runtime_suspended(cdev->dev))
 		return IRQ_NONE;
-	}
 
 	ir = m_can_read(cdev, M_CAN_IR);
 	m_can_coalescing_update(cdev, ir);
-- 
2.45.2

[PATCH 3/7] can: m_can: Remove m_can_rx_peripheral indirection

[Markus Schneider-Pargmann]

m_can_rx_peripheral() is a wrapper around m_can_rx_handler() that calls
m_can_disable_all_interrupts() on error. The same handling for the same
error path is done in m_can_isr() as well.

So remove m_can_rx_peripheral() and do the call from m_can_isr()
directly.

Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
---
 drivers/net/can/m_can/m_can.c | 18 +-----------------
 1 file changed, 1 insertion(+), 17 deletions(-)

diff --git a/drivers/net/can/m_can/m_can.c b/drivers/net/can/m_can/m_can.c
index fd600ab93218..42ed7f0fea78 100644
--- a/drivers/net/can/m_can/m_can.c
+++ b/drivers/net/can/m_can/m_can.c
@@ -1037,22 +1037,6 @@ static int m_can_rx_handler(struct net_device *dev, int quota, u32 irqstatus)
 	return work_done;
 }
 
-static int m_can_rx_peripheral(struct net_device *dev, u32 irqstatus)
-{
-	struct m_can_classdev *cdev = netdev_priv(dev);
-	int work_done;
-
-	work_done = m_can_rx_handler(dev, NAPI_POLL_WEIGHT, irqstatus);
-
-	/* Don't re-enable interrupts if the driver had a fatal error
-	 * (e.g., FIFO read failure).
-	 */
-	if (work_done < 0)
-		m_can_disable_all_interrupts(cdev);
-
-	return work_done;
-}
-
 static int m_can_poll(struct napi_struct *napi, int quota)
 {
 	struct net_device *dev = napi->dev;
@@ -1250,7 +1234,7 @@ static irqreturn_t m_can_isr(int irq, void *dev_id)
 		} else {
 			int pkts;
 
-			pkts = m_can_rx_peripheral(dev, ir);
+			pkts = m_can_rx_handler(dev, NAPI_POLL_WEIGHT, ir);
 			if (pkts < 0)
 				goto out_fail;
 		}
-- 
2.45.2

[PATCH 4/7] can: m_can: Do not cancel timer from within timer

[Markus Schneider-Pargmann]

On setups without interrupts, the interrupt handler is called from a
timer callback. For non-peripheral receives napi is scheduled,
interrupts are disabled and the timer is canceled with a blocking call.
In case of an error this can happen as well.

Check if napi is scheduled in the timer callback after the interrupt
handler executed. If napi is scheduled, the timer is disabled. It will
be reenabled by m_can_poll().

Return error values from the interrupt handler so that interrupt threads
and timer callback can deal differently with it. In case of the timer
we only disable the timer. The rest will be done when stopping the
interface.

Fixes: b382380c0d2d ("can: m_can: Add hrtimer to generate software interrupt")
Fixes: a163c5761019 ("can: m_can: Start/Cancel polling timer together with interrupts")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
---
 drivers/net/can/m_can/m_can.c | 58 ++++++++++++++++++++++++++---------
 1 file changed, 43 insertions(+), 15 deletions(-)

diff --git a/drivers/net/can/m_can/m_can.c b/drivers/net/can/m_can/m_can.c
index 42ed7f0fea78..e70c7100a3c9 100644
--- a/drivers/net/can/m_can/m_can.c
+++ b/drivers/net/can/m_can/m_can.c
@@ -487,7 +487,7 @@ static inline void m_can_disable_all_interrupts(struct m_can_classdev *cdev)
 
 	if (!cdev->net->irq) {
 		dev_dbg(cdev->dev, "Stop hrtimer\n");
-		hrtimer_cancel(&cdev->hrtimer);
+		hrtimer_try_to_cancel(&cdev->hrtimer);
 	}
 }
 
@@ -1201,11 +1201,16 @@ static void m_can_coalescing_update(struct m_can_classdev *cdev, u32 ir)
 			      HRTIMER_MODE_REL);
 }
 
-static irqreturn_t m_can_isr(int irq, void *dev_id)
+/**
+ * This interrupt handler is called either from the interrupt thread or a
+ * hrtimer. This has implications like cancelling a timer won't be possible
+ * blocking.
+ */
+static int m_can_interrupt_handler(struct m_can_classdev *cdev)
 {
-	struct net_device *dev = (struct net_device *)dev_id;
-	struct m_can_classdev *cdev = netdev_priv(dev);
+	struct net_device *dev = cdev->net;
 	u32 ir;
+	int ret;
 
 	if (pm_runtime_suspended(cdev->dev))
 		return IRQ_NONE;
@@ -1232,11 +1237,9 @@ static irqreturn_t m_can_isr(int irq, void *dev_id)
 			m_can_disable_all_interrupts(cdev);
 			napi_schedule(&cdev->napi);
 		} else {
-			int pkts;
-
-			pkts = m_can_rx_handler(dev, NAPI_POLL_WEIGHT, ir);
-			if (pkts < 0)
-				goto out_fail;
+			ret = m_can_rx_handler(dev, NAPI_POLL_WEIGHT, ir);
+			if (ret < 0)
+				return ret;
 		}
 	}
 
@@ -1254,8 +1257,9 @@ static irqreturn_t m_can_isr(int irq, void *dev_id)
 	} else  {
 		if (ir & (IR_TEFN | IR_TEFW)) {
 			/* New TX FIFO Element arrived */
-			if (m_can_echo_tx_event(dev) != 0)
-				goto out_fail;
+			ret = m_can_echo_tx_event(dev);
+			if (ret != 0)
+				return ret;
 		}
 	}
 
@@ -1263,16 +1267,31 @@ static irqreturn_t m_can_isr(int irq, void *dev_id)
 		can_rx_offload_threaded_irq_finish(&cdev->offload);
 
 	return IRQ_HANDLED;
+}
 
-out_fail:
-	m_can_disable_all_interrupts(cdev);
-	return IRQ_HANDLED;
+static irqreturn_t m_can_isr(int irq, void *dev_id)
+{
+	struct net_device *dev = (struct net_device *)dev_id;
+	struct m_can_classdev *cdev = netdev_priv(dev);
+	int ret;
+
+	ret =  m_can_interrupt_handler(cdev);
+	if (ret < 0) {
+		m_can_disable_all_interrupts(cdev);
+		return IRQ_HANDLED;
+	}
+
+	return ret;
 }
 
 static enum hrtimer_restart m_can_coalescing_timer(struct hrtimer *timer)
 {
 	struct m_can_classdev *cdev = container_of(timer, struct m_can_classdev, hrtimer);
 
+	if (cdev->can.state == CAN_STATE_BUS_OFF ||
+	    cdev->can.state == CAN_STATE_STOPPED)
+		return HRTIMER_NORESTART;
+
 	irq_wake_thread(cdev->net->irq, cdev->net);
 
 	return HRTIMER_NORESTART;
@@ -1973,8 +1992,17 @@ static enum hrtimer_restart hrtimer_callback(struct hrtimer *timer)
 {
 	struct m_can_classdev *cdev = container_of(timer, struct
 						   m_can_classdev, hrtimer);
+	int ret;
 
-	m_can_isr(0, cdev->net);
+	if (cdev->can.state == CAN_STATE_BUS_OFF ||
+	    cdev->can.state == CAN_STATE_STOPPED)
+		return HRTIMER_NORESTART;
+
+	ret = m_can_interrupt_handler(cdev);
+
+	/* On error or if napi is scheduled to read, stop the timer */
+	if (ret < 0 || napi_is_scheduled(&cdev->napi))
+		return HRTIMER_NORESTART;
 
 	hrtimer_forward_now(timer, ms_to_ktime(HRTIMER_POLL_INTERVAL_MS));
 
-- 
2.45.2

Re: [PATCH 4/7] can: m_can: Do not cancel timer from within timer

[kernel test robot]

Hi Markus,

kernel test robot noticed the following build warnings:

[auto build test WARNING on mkl-can-next/testing]
[also build test WARNING on linus/master v6.10 next-20240726]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch#_base_tree_information]

url:    https://github.com/intel-lab-lkp/linux/commits/Markus-Schneider-Pargmann/can-m_can-Reset-coalescing-during-suspend-resume/20240727-042714
base:   https://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next.git testing
patch link:    https://lore.kernel.org/r/20240726195944.2414812-5-msp%40baylibre.com
patch subject: [PATCH 4/7] can: m_can: Do not cancel timer from within timer
config: m68k-allyesconfig (https://download.01.org/0day-ci/archive/20240727/202407271748.gsVE0Hih-lkp@intel.com/config)
compiler: m68k-linux-gcc (GCC) 14.1.0
reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20240727/202407271748.gsVE0Hih-lkp@intel.com/reproduce)

If you fix the issue in a separate patch/commit (i.e. not just a new version of
the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <lkp@intel.com>
| Closes: https://lore.kernel.org/oe-kbuild-all/202407271748.gsVE0Hih-lkp@intel.com/

All warnings (new ones prefixed by >>):

>> drivers/net/can/m_can/m_can.c:1205: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
    * This interrupt handler is called either from the interrupt thread or a


vim +1205 drivers/net/can/m_can/m_can.c

  1203	
  1204	/**
> 1205	 * This interrupt handler is called either from the interrupt thread or a
  1206	 * hrtimer. This has implications like cancelling a timer won't be possible
  1207	 * blocking.
  1208	 */
  1209	static int m_can_interrupt_handler(struct m_can_classdev *cdev)
  1210	{
  1211		struct net_device *dev = cdev->net;
  1212		u32 ir;
  1213		int ret;
  1214	
  1215		if (pm_runtime_suspended(cdev->dev))
  1216			return IRQ_NONE;
  1217	
  1218		ir = m_can_read(cdev, M_CAN_IR);
  1219		m_can_coalescing_update(cdev, ir);
  1220		if (!ir)
  1221			return IRQ_NONE;
  1222	
  1223		/* ACK all irqs */
  1224		m_can_write(cdev, M_CAN_IR, ir);
  1225	
  1226		if (cdev->ops->clear_interrupts)
  1227			cdev->ops->clear_interrupts(cdev);
  1228	
  1229		/* schedule NAPI in case of
  1230		 * - rx IRQ
  1231		 * - state change IRQ
  1232		 * - bus error IRQ and bus error reporting
  1233		 */
  1234		if (ir & (IR_RF0N | IR_RF0W | IR_ERR_ALL_30X)) {
  1235			cdev->irqstatus = ir;
  1236			if (!cdev->is_peripheral) {
  1237				m_can_disable_all_interrupts(cdev);
  1238				napi_schedule(&cdev->napi);
  1239			} else {
  1240				ret = m_can_rx_handler(dev, NAPI_POLL_WEIGHT, ir);
  1241				if (ret < 0)
  1242					return ret;
  1243			}
  1244		}
  1245	
  1246		if (cdev->version == 30) {
  1247			if (ir & IR_TC) {
  1248				/* Transmission Complete Interrupt*/
  1249				u32 timestamp = 0;
  1250				unsigned int frame_len;
  1251	
  1252				if (cdev->is_peripheral)
  1253					timestamp = m_can_get_timestamp(cdev);
  1254				frame_len = m_can_tx_update_stats(cdev, 0, timestamp);
  1255				m_can_finish_tx(cdev, 1, frame_len);
  1256			}
  1257		} else  {
  1258			if (ir & (IR_TEFN | IR_TEFW)) {
  1259				/* New TX FIFO Element arrived */
  1260				ret = m_can_echo_tx_event(dev);
  1261				if (ret != 0)
  1262					return ret;
  1263			}
  1264		}
  1265	
  1266		if (cdev->is_peripheral)
  1267			can_rx_offload_threaded_irq_finish(&cdev->offload);
  1268	
  1269		return IRQ_HANDLED;
  1270	}
  1271	

-- 
0-DAY CI Kernel Test Service
https://github.com/intel/lkp-tests/wiki

[PATCH 5/7] can: m_can: disable_all_interrupts, not clear active_interrupts

[Markus Schneider-Pargmann]

active_interrupts is a cache for the enabled interrupts and not the
global masking of interrupts. Do not clear this variable otherwise we
may loose the state of the interrupts.

Fixes: 07f25091ca02 ("can: m_can: Implement receive coalescing")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
---
 drivers/net/can/m_can/m_can.c | 1 -
 1 file changed, 1 deletion(-)

diff --git a/drivers/net/can/m_can/m_can.c b/drivers/net/can/m_can/m_can.c
index e70c7100a3c9..bf4a9ae76db9 100644
--- a/drivers/net/can/m_can/m_can.c
+++ b/drivers/net/can/m_can/m_can.c
@@ -483,7 +483,6 @@ static inline void m_can_disable_all_interrupts(struct m_can_classdev *cdev)
 {
 	m_can_coalescing_disable(cdev);
 	m_can_write(cdev, M_CAN_ILE, 0x0);
-	cdev->active_interrupts = 0x0;
 
 	if (!cdev->net->irq) {
 		dev_dbg(cdev->dev, "Stop hrtimer\n");
-- 
2.45.2

[PATCH 6/7] can: m_can: Reset cached active_interrupts on start

[Markus Schneider-Pargmann]

To force writing the enabled interrupts, reset the active_interrupts
cache.

Fixes: 07f25091ca02 ("can: m_can: Implement receive coalescing")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
---
 drivers/net/can/m_can/m_can.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/can/m_can/m_can.c b/drivers/net/can/m_can/m_can.c
index bf4a9ae76db9..7c9ad9f7174e 100644
--- a/drivers/net/can/m_can/m_can.c
+++ b/drivers/net/can/m_can/m_can.c
@@ -1542,6 +1542,7 @@ static int m_can_chip_config(struct net_device *dev)
 		else
 			interrupts &= ~(IR_ERR_LEC_31X);
 	}
+	cdev->active_interrupts = 0;
 	m_can_interrupt_enable(cdev, interrupts);
 
 	/* route all interrupts to INT0 */
-- 
2.45.2

[PATCH 7/7] can: m_can: Limit coalescing to peripheral instances

[Markus Schneider-Pargmann]

The use of coalescing for non-peripheral chips in the current
implementation is limited to non-existing. Disable the possibility to
set coalescing through ethtool.

Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
---
 drivers/net/can/m_can/m_can.c | 16 +++++++++-------
 1 file changed, 9 insertions(+), 7 deletions(-)

diff --git a/drivers/net/can/m_can/m_can.c b/drivers/net/can/m_can/m_can.c
index 7c9ad9f7174e..663eb4247029 100644
--- a/drivers/net/can/m_can/m_can.c
+++ b/drivers/net/can/m_can/m_can.c
@@ -2182,7 +2182,7 @@ static int m_can_set_coalesce(struct net_device *dev,
 	return 0;
 }
 
-static const struct ethtool_ops m_can_ethtool_ops = {
+static const struct ethtool_ops m_can_ethtool_ops_coalescing = {
 	.supported_coalesce_params = ETHTOOL_COALESCE_RX_USECS_IRQ |
 		ETHTOOL_COALESCE_RX_MAX_FRAMES_IRQ |
 		ETHTOOL_COALESCE_TX_USECS_IRQ |
@@ -2193,18 +2193,20 @@ static const struct ethtool_ops m_can_ethtool_ops = {
 	.set_coalesce = m_can_set_coalesce,
 };
 
-static const struct ethtool_ops m_can_ethtool_ops_polling = {
+static const struct ethtool_ops m_can_ethtool_ops = {
 	.get_ts_info = ethtool_op_get_ts_info,
 };
 
-static int register_m_can_dev(struct net_device *dev)
+static int register_m_can_dev(struct m_can_classdev *cdev)
 {
+	struct net_device *dev = cdev->net;
+
 	dev->flags |= IFF_ECHO;	/* we support local echo */
 	dev->netdev_ops = &m_can_netdev_ops;
-	if (dev->irq)
-		dev->ethtool_ops = &m_can_ethtool_ops;
+	if (dev->irq && cdev->is_peripheral)
+		dev->ethtool_ops = &m_can_ethtool_ops_coalescing;
 	else
-		dev->ethtool_ops = &m_can_ethtool_ops_polling;
+		dev->ethtool_ops = &m_can_ethtool_ops;
 
 	return register_candev(dev);
 }
@@ -2390,7 +2392,7 @@ int m_can_class_register(struct m_can_classdev *cdev)
 	if (ret)
 		goto rx_offload_del;
 
-	ret = register_m_can_dev(cdev->net);
+	ret = register_m_can_dev(cdev);
 	if (ret) {
 		dev_err(cdev->dev, "registering %s failed (err=%d)\n",
 			cdev->net->name, ret);
-- 
2.45.2