From: Siddharth Vadapalli <s-vadapalli@ti.com>
To: <nm@ti.com>, <vigneshr@ti.com>, <kristo@kernel.org>,
<robh@kernel.org>, <krzk+dt@kernel.org>, <conor+dt@kernel.org>
Cc: <devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>, <srk@ti.com>,
<s-vadapalli@ti.com>
Subject: [PATCH 2/3] arm64: dts: ti: k3-j784s4-j742s2-evm: Add overlay for PCIe NTB
Date: Sun, 2 Feb 2025 15:06:29 +0530 [thread overview]
Message-ID: <20250202093636.2699064-3-s-vadapalli@ti.com> (raw)
In-Reply-To: <20250202093636.2699064-1-s-vadapalli@ti.com>
PCIe NTB (Non-Transparent-Bridge) allows connecting the memory of
multiple PCIe Hosts (Root-Complex). The number of such hosts is
determined by the number of PCIe instances configured for NTB operation
on the device which intends to enable NTB functionality. Add a device-tree
overlay to configure PCIE0 and PCIE1 instances of PCIe on either J784S4 EVM
or J742S2 EVM for NTB operation. This shall allow connecting the memory of
two PCIe Hosts via PCIE0 and PCIE1 on J784S4 EVM or J742S2 EVM
respectively.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
---
arch/arm64/boot/dts/ti/Makefile | 7 ++
.../dts/ti/k3-j784s4-j742s2-evm-pcie-ntb.dtso | 92 +++++++++++++++++++
2 files changed, 99 insertions(+)
create mode 100644 arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-pcie-ntb.dtso
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index 1097ab30f5a9..dbeb5d7401f7 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -128,6 +128,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm.dtb
dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm-pcie0-pcie1-ep.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm-quad-port-eth-exp1.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm-usxgmii-exp1-exp2.dtbo
+dtb-$(CONFIG_ARCH_K3) += k3-j784s4-j742s2-evm-pcie-ntb.dtbo
# Boards with J742S2 SoC
dtb-$(CONFIG_ARCH_K3) += k3-j742s2-evm.dtb
@@ -212,6 +213,10 @@ k3-j721e-sk-csi2-dual-imx219-dtbs := k3-j721e-sk.dtb \
k3-j721e-sk-csi2-dual-imx219.dtbo
k3-j721s2-evm-pcie1-ep-dtbs := k3-j721s2-common-proc-board.dtb \
k3-j721s2-evm-pcie1-ep.dtbo
+k3-j742s2-evm-pcie-ntb-dtbs := k3-j742s2-evm.dtb \
+ k3-j784s4-j742s2-evm-pcie-ntb.dtbo
+k3-j784s4-evm-pcie-ntb-dtbs := k3-j784s4-evm.dtb \
+ k3-j784s4-j742s2-evm-pcie-ntb.dtbo
k3-j784s4-evm-pcie0-pcie1-ep-dtbs := k3-j784s4-evm.dtb \
k3-j784s4-evm-pcie0-pcie1-ep.dtbo
k3-j784s4-evm-quad-port-eth-exp1-dtbs := k3-j784s4-evm.dtb \
@@ -247,6 +252,8 @@ dtb- += k3-am625-beagleplay-csi2-ov5640.dtb \
k3-j721e-evm-pcie1-ep.dtb \
k3-j721e-sk-csi2-dual-imx219.dtb \
k3-j721s2-evm-pcie1-ep.dtb \
+ k3-j742s2-evm-pcie-ntb.dtb \
+ k3-j784s4-evm-pcie-ntb.dtb \
k3-j784s4-evm-pcie0-pcie1-ep.dtb \
k3-j784s4-evm-quad-port-eth-exp1.dtb \
k3-j784s4-evm-usxgmii-exp1-exp2.dtb
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-pcie-ntb.dtso b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-pcie-ntb.dtso
new file mode 100644
index 000000000000..e44173f670fa
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-pcie-ntb.dtso
@@ -0,0 +1,92 @@
+// SPDX-License-Identifier: GPL-2.0-only OR MIT
+/**
+ * DT Overlay for enabling NTB functionality using PCIE0 and PCIE1 instances of
+ * PCIe on the J784S4 EVM and the J742S2 EVM.
+ *
+ * J784S4 EVM Product Link: https://www.ti.com/tool/J784S4XEVM
+ * J742S2 EVM Product Link: https://www.ti.com/tool/J742S2XH01EVM
+ *
+ * Copyright (C) 2025 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/soc/ti,sci_pm_domain.h>
+
+#include "k3-pinctrl.h"
+
+&{/} {
+ epf_bus {
+ compatible = "pci-epf-bus";
+
+ ntb {
+ compatible = "pci-epf-ntb";
+ epcs = <&pcie0_ep>, <&pcie1_ep>;
+ epc-names = "primary", "secondary";
+ vendor-id = /bits/ 16 <0x104c>;
+ device-id = /bits/ 16 <0xb012>;
+ num-mws = <4>;
+ mws-size = <0x100000>, <0x100000>, <0x100000>, <0x100000>;
+ };
+ };
+};
+
+&pcie0_rc {
+ status = "disabled";
+};
+
+&pcie1_rc {
+ status = "disabled";
+};
+
+&cbass_main {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&gic500>;
+
+ pcie0_ep: pcie-ep@2900000 {
+ compatible = "ti,j784s4-pcie-ep";
+ reg = <0x00 0x02900000 0x00 0x1000>,
+ <0x00 0x02907000 0x00 0x400>,
+ <0x00 0x0d000000 0x00 0x00800000>,
+ <0x00 0x10000000 0x00 0x08000000>;
+ reg-names = "intd_cfg", "user_cfg", "reg", "mem";
+ interrupt-names = "link_state";
+ interrupts = <GIC_SPI 318 IRQ_TYPE_EDGE_RISING>;
+ ti,syscon-pcie-ctrl = <&pcie0_ctrl 0x0>;
+ max-link-speed = <3>;
+ num-lanes = <4>;
+ power-domains = <&k3_pds 332 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 332 0>;
+ clock-names = "fck";
+ max-functions = /bits/ 8 <6>;
+ max-virtual-functions = /bits/ 8 <4 4 4 4 0 0>;
+ dma-coherent;
+ phys = <&serdes1_pcie0_link>;
+ phy-names = "pcie-phy";
+ };
+
+ pcie1_ep: pcie-ep@2910000 {
+ compatible = "ti,j784s4-pcie-ep";
+ reg = <0x00 0x02910000 0x00 0x1000>,
+ <0x00 0x02917000 0x00 0x400>,
+ <0x00 0x0d800000 0x00 0x00800000>,
+ <0x00 0x18000000 0x00 0x08000000>;
+ reg-names = "intd_cfg", "user_cfg", "reg", "mem";
+ interrupt-names = "link_state";
+ interrupts = <GIC_SPI 330 IRQ_TYPE_EDGE_RISING>;
+ ti,syscon-pcie-ctrl = <&pcie1_ctrl 0x0>;
+ max-link-speed = <3>;
+ num-lanes = <2>;
+ power-domains = <&k3_pds 333 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 333 0>;
+ clock-names = "fck";
+ max-functions = /bits/ 8 <6>;
+ max-virtual-functions = /bits/ 8 <4 4 4 4 0 0>;
+ dma-coherent;
+ phys = <&serdes0_pcie1_link>;
+ phy-names = "pcie-phy";
+ };
+};
--
2.43.0
next prev parent reply other threads:[~2025-02-02 9:37 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-02-02 9:36 [PATCH 0/3] PCIe NTB and USB Overlays for J721E, J742S2 and J784S4 Siddharth Vadapalli
2025-02-02 9:36 ` [PATCH 1/3] arm64: dts: ti: k3-j721e-evm: Add overlay for PCIe NTB functionality Siddharth Vadapalli
2025-02-02 9:36 ` Siddharth Vadapalli [this message]
2025-02-24 12:05 ` [PATCH 2/3] arm64: dts: ti: k3-j784s4-j742s2-evm: Add overlay for PCIe NTB Vignesh Raghavendra
2025-02-24 12:11 ` Siddharth Vadapalli
2025-02-02 9:36 ` [PATCH 3/3] arm64: dts: ti: k3-j784s4-j742s2-evm: Add overlay to enable USB0 Type-A Siddharth Vadapalli
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20250202093636.2699064-3-s-vadapalli@ti.com \
--to=s-vadapalli@ti.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=kristo@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=nm@ti.com \
--cc=robh@kernel.org \
--cc=srk@ti.com \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®