[PATCH v2 2/5] arm64: dts: ti: k3-am62a-phycore-som: Add boot phase tags

[Wadim Egorov <w.egorov@phytec.de>]

The bootph-all and bootph-pre-ram tags were introduced in dt-schema
(dtschema/schemas/bootph.yaml) to define node usage across different
boot phases.

Add boot phase tags to all required nodes to ensure boot support from
all sources, including UART, USB (DFU), Ethernet, uSD card, eMMC, and
OSPI NOR Flash.

Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
---
v1: http://lists.infradead.org/pipermail/linux-arm-kernel/2025-February/1006241.html
v2:
  - Add bootph-all to cpsw_port1 & main_pktdma
  - Drop bootph-all from cpsw3g
---
 arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi b/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi
index a5aceaa39670..7920559e84a3 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi
@@ -42,6 +42,7 @@ memory@80000000 {
 		device_type = "memory";
 		/* 2G RAM */
 		reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
+		bootph-all;
 	};
 
 	reserved-memory {
@@ -99,6 +100,7 @@ main_i2c0_pins_default: main-i2c0-default-pins {
 			AM62AX_IOPAD(0x1e0, PIN_INPUT_PULLUP, 0) /* (D17) I2C0_SCL */
 			AM62AX_IOPAD(0x1e4, PIN_INPUT_PULLUP, 0) /* (E16) I2C0_SDA */
 		>;
+		bootph-all;
 	};
 
 	main_mdio1_pins_default: main-mdio1-default-pins {
@@ -106,6 +108,7 @@ main_mdio1_pins_default: main-mdio1-default-pins {
 			AM62AX_IOPAD(0x160, PIN_OUTPUT, 0) /* (V12) MDIO0_MDC */
 			AM62AX_IOPAD(0x15c, PIN_INPUT, 0) /* (V13) MDIO0_MDIO */
 		>;
+		bootph-all;
 	};
 
 	main_mmc0_pins_default: main-mmc0-default-pins {
@@ -121,6 +124,7 @@ AM62AX_IOPAD(0x200, PIN_INPUT_PULLUP, 0) /* (W7) MMC0_DAT5 */
 			AM62AX_IOPAD(0x1fc, PIN_INPUT_PULLUP, 0) /* (W9) MMC0_DAT6 */
 			AM62AX_IOPAD(0x1f8, PIN_INPUT_PULLUP, 0) /* (AB8) MMC0_DAT7 */
 		>;
+		bootph-all;
 	};
 
 	main_rgmii1_pins_default: main-rgmii1-default-pins {
@@ -138,6 +142,7 @@ AM62AX_IOPAD(0x140, PIN_OUTPUT, 0) /* (AA17) RGMII1_TD3 */
 			AM62AX_IOPAD(0x130, PIN_OUTPUT, 0) /* (AB17) RGMII1_TXC */
 			AM62AX_IOPAD(0x12c, PIN_OUTPUT, 0) /* (W16) RGMII1_TX_CTL */
 		>;
+		bootph-all;
 	};
 
 	ospi0_pins_default: ospi0-default-pins {
@@ -155,6 +160,7 @@ AM62AX_IOPAD(0x024, PIN_INPUT, 0) /* (J20) OSPI0_D6 */
 			AM62AX_IOPAD(0x028, PIN_INPUT, 0) /* (J22) OSPI0_D7 */
 			AM62AX_IOPAD(0x008, PIN_INPUT, 0) /* (L21) OSPI0_DQS */
 		>;
+		bootph-all;
 	};
 
 	pmic_irq_pins_default: pmic-irq-default-pins {
@@ -168,11 +174,13 @@ &cpsw3g {
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_rgmii1_pins_default>;
+	status = "okay";
 };
 
 &cpsw_port1 {
 	phy-mode = "rgmii-rxid";
 	phy-handle = <&cpsw3g_phy1>;
+	bootph-all;
 };
 
 &cpsw3g_mdio {
@@ -182,6 +190,7 @@ &cpsw3g_mdio {
 	cpsw3g_phy1: ethernet-phy@1 {
 		compatible = "ethernet-phy-id2000.a231", "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
+		bootph-all;
 		ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
 		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
 		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
@@ -196,6 +205,7 @@ &main_i2c0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_i2c0_pins_default>;
 	clock-frequency = <400000>;
+	bootph-all;
 	status = "okay";
 
 	pmic@30 {
@@ -302,6 +312,10 @@ &main_gpio_intr {
 	status = "okay";
 };
 
+&main_pktdma {
+	bootph-all;
+};
+
 &ospi0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&ospi0_pins_default>;
@@ -318,6 +332,7 @@ serial_flash: flash@0 {
 		cdns,tchsh-ns = <60>;
 		cdns,tslch-ns = <60>;
 		cdns,read-delay = <0>;
+		bootph-all;
 	};
 };
 
@@ -326,5 +341,6 @@ &sdhci0 {
 	pinctrl-0 = <&main_mmc0_pins_default>;
 	disable-wp;
 	non-removable;
+	bootph-all;
 	status = "okay";
 };
-- 
2.34.1