From: Nihal Kumar Gupta <nihal.gupta@oss.qualcomm.com>
To: Bjorn Andersson <andersson@kernel.org>,
Konrad Dybcio <konradybcio@kernel.org>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>
Cc: linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
Suresh Vankadara <svankada@qti.qualcomm.com>,
Vikram Sharma <vikram.sharma@oss.qualcomm.com>,
Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>,
Nihal Kumar Gupta <nihal.gupta@oss.qualcomm.com>
Subject: [PATCH 5/6] arm64: dts: qcom: glymur-crd: Add ov08x40 RGB sensor on CSIPHY4
Date: Mon, 07 Sep 2026 15:37:48 +0530 [thread overview]
Message-ID: <20260907-glymur_camss_dts-v1-5-6c2ced5ea5f9@oss.qualcomm.com> (raw)
In-Reply-To: <20260907-glymur_camss_dts-v1-0-6c2ced5ea5f9@oss.qualcomm.com>
Define ov08x40 on cci1_i2c1. The RGB sensor is connected to
CSIPHY4 in four-lane mode.
Signed-off-by: Nihal Kumar Gupta <nihal.gupta@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/glymur-crd.dtsi | 64 ++++++++++++++++++++++++++++++++
1 file changed, 64 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/glymur-crd.dtsi b/arch/arm64/boot/dts/qcom/glymur-crd.dtsi
index 68a191890b7d875564080d9fccf85ae9451cf0d0..af65d739676743742c36ed07fc554cf34f34a36e 100644
--- a/arch/arm64/boot/dts/qcom/glymur-crd.dtsi
+++ b/arch/arm64/boot/dts/qcom/glymur-crd.dtsi
@@ -11,6 +11,7 @@
#include "smb2370.dtsi" /* SPMI2: SID-9/10/11 */
#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/media/video-interfaces.h>
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
/ {
@@ -589,6 +590,62 @@ vreg_l4h_e0_1p2: ldo4 {
};
};
+&camss {
+ status = "okay";
+};
+
+&camss_csiphy4_inep {
+ data-lanes = <1 2 3 4>;
+};
+
+&cci1 {
+ pinctrl-0 = <&cci1_1_default>;
+ pinctrl-1 = <&cci1_1_sleep>;
+
+ status = "okay";
+};
+
+&cci1_i2c1 {
+ camera@36 {
+ compatible = "ovti,ov08x40";
+ reg = <0x36>;
+
+ reset-gpios = <&tlmm 239 GPIO_ACTIVE_LOW>;
+ pinctrl-0 = <&cam_mclk4_default &cam_reset4_default>;
+ pinctrl-names = "default";
+
+ clocks = <&camcc CAM_CC_MCLK4_CLK>;
+ assigned-clocks = <&camcc CAM_CC_MCLK4_CLK>;
+ assigned-clock-rates = <19200000>;
+
+ avdd-supply = <&vreg_l7p>;
+ dovdd-supply = <&vreg_l4p>;
+ dvdd-supply = <&vreg_l4p>;
+
+ port {
+ ov08x40_out_ep: endpoint {
+ data-lanes = <1 2 3 4>;
+ link-frequencies = /bits/ 64 <400000000>;
+ remote-endpoint = <&csiphy4_in_ep>;
+ };
+ };
+ };
+};
+
+&csiphy4 {
+ vdda-0p9-supply = <&vreg_l1f_e1_0p82>;
+ vdda-1p2-supply = <&vreg_l4f_e1_1p08>;
+
+ status = "okay";
+};
+
+&csiphy4_in_ep {
+ bus-type = <MEDIA_BUS_TYPE_CSI2_DPHY>;
+ clock-lanes = <0>;
+ data-lanes = <1 2 3 4>;
+ remote-endpoint = <&ov08x40_out_ep>;
+};
+
&i2c9 {
clock-frequency = <400000>;
@@ -1200,6 +1257,13 @@ wwan_reg_en: wwan-reg-en-state {
drive-strength = <2>;
bias-disable;
};
+
+ cam_reset4_default: cam-reset4-default-state {
+ pins = "gpio239";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
};
&uart14 {
--
2.34.1
next prev parent reply other threads:[~2026-09-07 10:08 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-09-07 10:07 [PATCH 0/6] Add CCI and CAMSS support for Glymur Nihal Kumar Gupta
2026-09-07 10:07 ` [PATCH 1/6] arm64: dts: qcom: glymur: Add CAMSS and CSIPHY nodes " Nihal Kumar Gupta
2026-09-14 14:10 ` Konrad Dybcio
2026-09-07 10:07 ` [PATCH 2/6] arm64: dts: qcom: glymur: Add CCI definitions " Nihal Kumar Gupta
2026-09-07 10:47 ` Abel Vesa
2026-09-07 10:07 ` [PATCH 3/6] arm64: dts: qcom: glymur: Add camera MCLK pinctrl Nihal Kumar Gupta
2026-09-07 10:47 ` Abel Vesa
2026-09-07 10:07 ` [PATCH 4/6] arm64: dts: qcom: glymur-crd: Add PM8010 camera PMIC Nihal Kumar Gupta
2026-09-07 10:07 ` Nihal Kumar Gupta [this message]
2026-09-07 10:47 ` [PATCH 5/6] arm64: dts: qcom: glymur-crd: Add ov08x40 RGB sensor on CSIPHY4 Abel Vesa
2026-09-07 10:07 ` [PATCH 6/6] arm64: defconfig: Enable OV08X40 camera sensor driver Nihal Kumar Gupta
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260907-glymur_camss_dts-v1-5-6c2ced5ea5f9@oss.qualcomm.com \
--to=nihal.gupta@oss.qualcomm.com \
--cc=andersson@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=konrad.dybcio@oss.qualcomm.com \
--cc=konradybcio@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh@kernel.org \
--cc=svankada@qti.qualcomm.com \
--cc=vikram.sharma@oss.qualcomm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®