[PATCH v2 4/6] arm64: dts: qcom: glymur-crd: Add PM8010 camera PMIC

[Nihal Kumar Gupta <nihal.gupta@oss.qualcomm.com>]

From: Jishnu Prakash <jishnu.prakash@oss.qualcomm.com>

Add the PM8010 PMIC node with seven LDO regulators and pinctrl
configuration for reset pin. The LDOs are needed to power the
camera sensors and associated hardware.

Signed-off-by: Jishnu Prakash <jishnu.prakash@oss.qualcomm.com>
Signed-off-by: Nihal Kumar Gupta <nihal.gupta@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/glymur-crd.dtsi | 75 ++++++++++++++++++++++++++++++++
 1 file changed, 75 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/glymur-crd.dtsi b/arch/arm64/boot/dts/qcom/glymur-crd.dtsi
index 58158b51fe295fd111f3a3d7778ca531467e900a..ebc8da58a79ed6a77916c70c7fd93ab06e185644 100644
--- a/arch/arm64/boot/dts/qcom/glymur-crd.dtsi
+++ b/arch/arm64/boot/dts/qcom/glymur-crd.dtsi
@@ -671,6 +671,72 @@ ptn3222_1: redriver@47 {
 
 		#phy-cells = <0>;
 	};
+
+	pm8010: pmic@8 {
+		compatible = "qcom,pm8010-i2c";
+		reg = <0x8>;
+
+		reset-gpios = <&tlmm 106 GPIO_ACTIVE_LOW>;
+
+		vdd-l1-l2-supply = <&vreg_l6p>;
+		vdd-l3-l4-supply = <&vreg_bob1_e0>;
+		vdd-l5-supply = <&vreg_bob1_e0>;
+		vdd-l6-supply = <&vreg_bob1_e0>;
+		vdd-l7-supply = <&vreg_bob1_e0>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pm8010_default>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-ranges = <&pm8010 0 0 2>;
+
+		#thermal-sensor-cells = <0>;
+
+		regulators {
+			vreg_l1p: ldo1 {
+				regulator-name = "vreg_l1p";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+			};
+
+			vreg_l2p: ldo2 {
+				regulator-name = "vreg_l2p";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+			};
+
+			vreg_l3p: ldo3 {
+				regulator-name = "vreg_l3p";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+			};
+
+			vreg_l4p: ldo4 {
+				regulator-name = "vreg_l4p";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			vreg_l5p: ldo5 {
+				regulator-name = "vreg_l5p";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+			};
+
+			vreg_l6p: ldo6 {
+				regulator-name = "vreg_l6p";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			vreg_l7p: ldo7 {
+				regulator-name = "vreg_l7p";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+			};
+		};
+	};
 };
 
 &i2c8 {
@@ -1106,6 +1172,15 @@ wake-n-pins {
 		};
 	};
 
+	pm8010_default: pm8010-default-state {
+		reset-n-pins {
+			pins = "gpio106";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
 	sdc2_card_det_n: sd-card-det-n-state {
 		pins = "gpio221";
 		function = "gpio";

-- 
2.34.1