[PATCH v2 5/6] arm64: dts: qcom: glymur-crd: Add ov08x40 RGB sensor on CSIPHY4

[Nihal Kumar Gupta <nihal.gupta@oss.qualcomm.com>]

Define ov08x40 on cci1_i2c1. The RGB sensor is connected to
CSIPHY4 in four-lane mode.

Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Signed-off-by: Nihal Kumar Gupta <nihal.gupta@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/glymur-crd.dtsi | 64 ++++++++++++++++++++++++++++++++
 1 file changed, 64 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/glymur-crd.dtsi b/arch/arm64/boot/dts/qcom/glymur-crd.dtsi
index ebc8da58a79ed6a77916c70c7fd93ab06e185644..1e3ed597c1294272a53c4a6ecd67da0aa6dba528 100644
--- a/arch/arm64/boot/dts/qcom/glymur-crd.dtsi
+++ b/arch/arm64/boot/dts/qcom/glymur-crd.dtsi
@@ -11,6 +11,7 @@
 #include "smb2370.dtsi"         /* SPMI2: SID-9/10/11            */
 
 #include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/media/video-interfaces.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 
 / {
@@ -589,6 +590,62 @@ vreg_l4h_e0_1p2: ldo4 {
 	};
 };
 
+&camss {
+	status = "okay";
+};
+
+&camss_csiphy4_inep {
+	data-lanes = <1 2 3 4>;
+};
+
+&cci1 {
+	pinctrl-0 = <&cci1_1_default>;
+	pinctrl-1 = <&cci1_1_sleep>;
+
+	status = "okay";
+};
+
+&cci1_i2c1 {
+	camera@36 {
+		compatible = "ovti,ov08x40";
+		reg = <0x36>;
+
+		reset-gpios = <&tlmm 239 GPIO_ACTIVE_LOW>;
+		pinctrl-0 = <&cam_mclk4_default &cam_reset4_default>;
+		pinctrl-names = "default";
+
+		clocks = <&camcc CAM_CC_MCLK4_CLK>;
+		assigned-clocks = <&camcc CAM_CC_MCLK4_CLK>;
+		assigned-clock-rates = <19200000>;
+
+		avdd-supply = <&vreg_l7p>;
+		dovdd-supply = <&vreg_l4p>;
+		dvdd-supply = <&vreg_l4p>;
+
+		port {
+			ov08x40_out_ep: endpoint {
+				data-lanes = <1 2 3 4>;
+				link-frequencies = /bits/ 64 <400000000>;
+				remote-endpoint = <&csiphy4_in_ep>;
+			};
+		};
+	};
+};
+
+&csiphy4 {
+	vdda-0p9-supply = <&vreg_l1f_e1_0p82>;
+	vdda-1p2-supply = <&vreg_l4f_e1_1p08>;
+
+	status = "okay";
+};
+
+&csiphy4_in_ep {
+	bus-type = <MEDIA_BUS_TYPE_CSI2_DPHY>;
+	clock-lanes = <0>;
+	data-lanes = <1 2 3 4>;
+	remote-endpoint = <&ov08x40_out_ep>;
+};
+
 &i2c9 {
 	clock-frequency = <400000>;
 
@@ -1229,6 +1286,13 @@ wwan_reg_en: wwan-reg-en-state {
 		drive-strength = <2>;
 		bias-disable;
 	};
+
+	cam_reset4_default: cam-reset4-default-state {
+		pins = "gpio239";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
 };
 
 &uart14 {

-- 
2.34.1