[PATCH 1/6] arm64: dts: qcom: talos-lyra-evk: Add LT9611UXD HDMI bridge support

[anand.tiwari@oss.qualcomm.com]

From: Mohit Dsor <mohit.dsor@oss.qualcomm.com>

Add support for the Lontium LT9611UXD DSI-to-HDMI bridge, enabled by
default on the Talos Lyra EVK base board DT, to provide HDMI output
on the DSI0_B2B connector on the carrier card.

LT9611UXD is connected through I2C2, with reset and interrupt
connected to TLMM GPIO61 and GPIO60 respectively.

Signed-off-by: Mohit Dsor <mohit.dsor@oss.qualcomm.com>
Signed-off-by: Anand Tiwari <anand.tiwari@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/talos-lyra-evk.dts | 105 ++++++++++++++++++++++++++++
 1 file changed, 105 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/talos-lyra-evk.dts b/arch/arm64/boot/dts/qcom/talos-lyra-evk.dts
index cfb563658fe0..ec5c10a40521 100644
--- a/arch/arm64/boot/dts/qcom/talos-lyra-evk.dts
+++ b/arch/arm64/boot/dts/qcom/talos-lyra-evk.dts
@@ -4,6 +4,8 @@
  */
 /dts-v1/;
 
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 #include "talos-lyra-evk-som.dtsi"
 
 / {
@@ -11,6 +13,10 @@ / {
 	compatible = "qcom,talos-lyra-evk", "qcom,qcs615", "qcom,sm6150";
 	chassis-type = "embedded";
 
+	aliases {
+		i2c2 = &i2c2;
+	};
+
 	dp0-connector {
 		compatible = "dp-connector";
 		label = "DP0";
@@ -25,6 +31,65 @@ dp0_connector_in: endpoint {
 		};
 	};
 
+	hdmi_connector: hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_out: endpoint {
+			remote-endpoint = <&hdmi_bridge_out>;
+			};
+		};
+	};
+
+	vreg_disp_3p3: regulator-disp-3p3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_disp_3p3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&tlmm 3 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-0 = <&lcd_bias_en>;
+		pinctrl-names = "default";
+	};
+
+};
+
+&i2c2 {
+	status = "okay";
+
+	hdmi_bridge: hdmi-bridge@41 {
+		compatible = "lontium,lt9611uxd";
+		reg = <0x41>;
+		interrupts-extended = <&tlmm 60 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&tlmm 61 GPIO_ACTIVE_LOW>;
+		vcc-supply = <&vreg_disp_3p3>;
+		vdd-supply = <&vreg_s4a>;
+
+		pinctrl-0 = <&bridge_irq_pin &bridge_rst_pin>;
+		pinctrl-names = "default";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				hdmi_bridge_in: endpoint {
+					remote-endpoint = <&mdss_dsi0_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				hdmi_bridge_out: endpoint {
+					remote-endpoint = <&hdmi_connector_out>;
+				};
+			};
+		};
+	};
 };
 
 &i2c5 {
@@ -74,6 +139,23 @@ &mdss_dp0_out {
 	remote-endpoint = <&dp0_connector_in>;
 };
 
+&mdss_dsi0 {
+	vdda-supply = <&vreg_l5a>;
+
+	status = "okay";
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&hdmi_bridge_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+	vdds-supply = <&vreg_l11a>;
+
+	status = "okay";
+};
+
 &pon_pwrkey {
 	status = "okay";
 };
@@ -135,3 +217,26 @@ &usb_qmpphy_2 {
 
 	status = "okay";
 };
+
+&tlmm {
+	lcd_bias_en: lcd-bias-en-state {
+		pins = "gpio3";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	bridge_irq_pin: bridge-irq-state {
+		pins = "gpio60";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	bridge_rst_pin: bridge-rst-state {
+		pins = "gpio61";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+};

-- 
2.55.0