[PATCH] riscv: dts: spacemit: k3: add USB3 port A (DRD) nodes

[PATCH] riscv: dts: spacemit: k3: add USB3 port A (DRD) nodes

[Chunyan Zhang]

Describe the DWC3 controller and its USB 2.0 PHY for USB3 port A
of the K3 SoC.

Only the U2 lane is described: Port A's SuperSpeed PHY has no driver
yet, so the port runs at high-speed (maximum-speed = "high-speed").

Enable USB3 port A with dr_mode = "peripheral", so it can be used as
a USB device.

Signed-off-by: Chunyan Zhang <chunyan.zhang@linux.spacemit.com>
---
 arch/riscv/boot/dts/spacemit/k3-pico-itx.dts |  9 ++++++
 arch/riscv/boot/dts/spacemit/k3.dtsi         | 30 ++++++++++++++++++++
 2 files changed, 39 insertions(+)

diff --git a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
index b084a35aa00e..74d4fdf9e405 100644
--- a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
+++ b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
@@ -323,6 +323,15 @@ &usb2_phy {
 	status = "okay";
 };
 
+&usb3a_u2phy {
+	status = "okay";
+};
+
+&usb3a {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
 &usb3d_u2phy {
 	status = "okay";
 };
diff --git a/arch/riscv/boot/dts/spacemit/k3.dtsi b/arch/riscv/boot/dts/spacemit/k3.dtsi
index c3f2dce0969c..220dfe29bb78 100644
--- a/arch/riscv/boot/dts/spacemit/k3.dtsi
+++ b/arch/riscv/boot/dts/spacemit/k3.dtsi
@@ -630,6 +630,36 @@ gmac2_axi_setup: stmmac-axi-config {
 			};
 		};
 
+		usb3a: usb@cad00000 {
+			compatible = "spacemit,k3-dwc3";
+			reg = <0x0 0xcad00000 0x0 0x10000>;
+			interrupts = <118 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-parent = <&saplic>;
+			clocks = <&syscon_apmu CLK_APMU_USB3_PORTA_BUS>;
+			clock-names = "usbdrd30";
+			resets = <&syscon_apmu RESET_APMU_USB3_A_AHB>,
+				 <&syscon_apmu RESET_APMU_USB3_A_VCC>,
+				 <&syscon_apmu RESET_APMU_USB3_A_PHY>;
+			reset-names = "ahb", "vcc", "phy";
+			phys = <&usb3a_u2phy>;
+			phy-names = "usb2-phy";
+			phy_type = "utmi";
+			snps,dis_enblslpm_quirk;
+			snps,dis_u2_susphy_quirk;
+			snps,dis-del-phy-power-chg-quirk;
+			snps,dis-tx-ipgap-linecheck-quirk;
+			maximum-speed = "high-speed";
+			status = "disabled";
+		};
+
+		usb3a_u2phy: phy@cad20000 {
+			compatible = "spacemit,k3-usb2-phy";
+			reg = <0x0 0xcad20000 0x0 0x200>;
+			clocks = <&syscon_apmu CLK_APMU_USB3_PORTA_BUS>;
+			#phy-cells = <0>;
+			status = "disabled";
+		};
+
 		pdma: dma-controller@d4000000 {
 			compatible = "spacemit,k3-pdma";
 			reg = <0x0 0xd4000000 0x0 0x4000>;
-- 
2.34.1