* [PATCH v1 00/11] arm64: qcom: Add initial support for LG V60 ThinQ 5G (timelm)
@ 2026-11-17 12:39 rofikkerneldev
2026-11-17 12:39 ` [PATCH v1 01/11] dt-bindings: arm: qcom: add " rofikkerneldev
` (10 more replies)
0 siblings, 11 replies; 12+ messages in thread
From: rofikkerneldev @ 2026-11-17 12:39 UTC (permalink / raw)
To: linux-arm-msm
Cc: devicetree, dri-devel, linux-input, linux-kernel,
Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Neil Armstrong, Dmitry Torokhov, rofikkerneldev
This series adds initial mainline support for the LG V60 ThinQ 5G (timelm),
an SM8250-based flagship smartphone released in 2020.
The series enables:
- DT binding and SoC board description for LG V60 ThinQ 5G (timelm)
- Memory reservations for bootloader and firmware log regions
- DRM panel driver and binding for the 1080x2460 SW43103 AMOLED display
- Touchscreen driver and binding for the Silicon Works SW42902 controller
- USB Type-C TCPM sink mode on PM8150B
- Bluetooth HCI on GENI UART6 with QCA6390 power sequencing
- Storage (UFS), SD card, volume keys, and thermal management
- Entries in MAINTAINERS for timelm platform, panel, and touchscreen
All patches pass checkpatch.pl --strict with 0 errors and 0 warnings,
and the device tree builds cleanly against Linux 7.4-rc3.
The series is also available on GitHub:
https://github.com/rofikkerneldev/linux_timelm/tree/timelm-v74-stage1
Signed-off-by: rofikkerneldev <rofikcoga@gmail.com>
rofikkerneldev (11):
dt-bindings: arm: qcom: add LG V60 ThinQ 5G (timelm)
arm64: dts: qcom: add LG V60 ThinQ 5G (timelm) support
arm64: dts: qcom: sm8250-lge-timelm: add reserved memory regions
dt-bindings: display: panel: add LG SW43103
drm/panel: add LG SW43103 panel driver
dt-bindings: input: touchscreen: add Silicon Works SW42902
Input: touchscreen: add Silicon Works SW42902 support
arm64: dts: qcom: sm8250-lge-timelm: enable SW43103 panel
arm64: dts: qcom: sm8250-lge-timelm: add SW42902 touchscreen
arm64: dts: qcom: sm8250-lge-timelm: enable USB Type-C
arm64: dts: qcom: sm8250-lge-timelm: add QCA6390 Bluetooth
.../devicetree/bindings/arm/qcom.yaml | 1 +
.../bindings/display/panel/lg,sw43103.yaml | 70 ++
.../input/touchscreen/lg,sw42902.yaml | 74 ++
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
MAINTAINERS | 19 +
arch/arm64/boot/dts/qcom/Makefile | 1 +
.../arm64/boot/dts/qcom/sm8250-lge-timelm.dts | 744 ++++++++++++++++++
drivers/gpu/drm/panel/Kconfig | 13 +
drivers/gpu/drm/panel/Makefile | 1 +
drivers/gpu/drm/panel/panel-lg-sw43103.c | 594 ++++++++++++++
drivers/input/touchscreen/Kconfig | 11 +
drivers/input/touchscreen/Makefile | 1 +
drivers/input/touchscreen/sw42902.c | 315 ++++++++
13 files changed, 1846 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/panel/lg,sw43103.yaml
create mode 100644 Documentation/devicetree/bindings/input/touchscreen/lg,sw42902.yaml
create mode 100644 arch/arm64/boot/dts/qcom/sm8250-lge-timelm.dts
create mode 100644 drivers/gpu/drm/panel/panel-lg-sw43103.c
create mode 100644 drivers/input/touchscreen/sw42902.c
--
2.39.5
^ permalink raw reply [flat|nested] 12+ messages in thread* [PATCH v1 01/11] dt-bindings: arm: qcom: add LG V60 ThinQ 5G (timelm) 2026-11-17 12:39 [PATCH v1 00/11] arm64: qcom: Add initial support for LG V60 ThinQ 5G (timelm) rofikkerneldev @ 2026-11-17 12:39 ` rofikkerneldev 2026-11-17 12:39 ` [PATCH v1 02/11] arm64: dts: qcom: add LG V60 ThinQ 5G (timelm) support rofikkerneldev ` (9 subsequent siblings) 10 siblings, 0 replies; 12+ messages in thread From: rofikkerneldev @ 2026-11-17 12:39 UTC (permalink / raw) To: linux-arm-msm Cc: devicetree, dri-devel, linux-input, linux-kernel, Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Neil Armstrong, Dmitry Torokhov, rofikkerneldev Document the compatible for the LG V60 ThinQ 5G (timelm), based on SM8250, and register the LG Electronics vendor prefix. Signed-off-by: rofikkerneldev <rofikcoga@gmail.com> --- Documentation/devicetree/bindings/arm/qcom.yaml | 1 + Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 2 files changed, 3 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml index 121ca557ce1ef..f8b34109171d0 100644 --- a/Documentation/devicetree/bindings/arm/qcom.yaml +++ b/Documentation/devicetree/bindings/arm/qcom.yaml @@ -1139,6 +1139,7 @@ properties: - items: - enum: + - lge,timelm - qcom,qrb5165-rb5 - qcom,sm8250-hdk - qcom,sm8250-mtp diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index 5471a06f93f10..fa50a81880f0b 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -971,6 +971,8 @@ patternProperties: description: Lenovo Group Ltd. "^lg,.*": description: LG Corporation + "^lge,.*": + description: LG Electronics "^lgphilips,.*": description: LG Display "^libretech,.*": -- 2.39.5 ^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v1 02/11] arm64: dts: qcom: add LG V60 ThinQ 5G (timelm) support 2026-11-17 12:39 [PATCH v1 00/11] arm64: qcom: Add initial support for LG V60 ThinQ 5G (timelm) rofikkerneldev 2026-11-17 12:39 ` [PATCH v1 01/11] dt-bindings: arm: qcom: add " rofikkerneldev @ 2026-11-17 12:39 ` rofikkerneldev 2026-11-17 12:39 ` [PATCH v1 03/11] arm64: dts: qcom: sm8250-lge-timelm: add reserved memory regions rofikkerneldev ` (8 subsequent siblings) 10 siblings, 0 replies; 12+ messages in thread From: rofikkerneldev @ 2026-11-17 12:39 UTC (permalink / raw) To: linux-arm-msm Cc: devicetree, dri-devel, linux-input, linux-kernel, Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Neil Armstrong, Dmitry Torokhov, rofikkerneldev Add initial support for the LG V60 ThinQ 5G (timelm), based on the Qualcomm SM8250 SoC. Describe the memory layout, PMIC regulators, buttons, serial console, UFS, SD card, and USB. Signed-off-by: rofikkerneldev <rofikcoga@gmail.com> --- MAINTAINERS | 6 + arch/arm64/boot/dts/qcom/Makefile | 1 + .../arm64/boot/dts/qcom/sm8250-lge-timelm.dts | 543 ++++++++++++++++++ 3 files changed, 550 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sm8250-lge-timelm.dts diff --git a/MAINTAINERS b/MAINTAINERS index ccbcdc0799b9f..315a4a000b405 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -15231,6 +15231,12 @@ Q: http://patchwork.linuxtv.org/project/linux-media/list/ T: git git://linuxtv.org/mkrufky/tuners.git F: drivers/media/dvb-frontends/lgdt3305.* +LG V60 THINQ 5G (TIMELM) SUPPORT +M: rofikkerneldev <rofikcoga@gmail.com> +L: linux-arm-msm@vger.kernel.org +S: Maintained +F: arch/arm64/boot/dts/qcom/sm8250-lge-timelm* + LIBATA PATA ARASAN COMPACT FLASH CONTROLLER M: Viresh Kumar <vireshk@kernel.org> L: linux-ide@vger.kernel.org diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index 88230c4e00ea9..91c9d95696f2a 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -409,6 +409,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8150-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8150-sony-xperia-kumano-bahamut.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8150-sony-xperia-kumano-griffin.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8250-hdk.dtb +dtb-$(CONFIG_ARCH_QCOM) += sm8250-lge-timelm.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8250-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8250-samsung-r8q.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8250-samsung-x1q.dtb diff --git a/arch/arm64/boot/dts/qcom/sm8250-lge-timelm.dts b/arch/arm64/boot/dts/qcom/sm8250-lge-timelm.dts new file mode 100644 index 0000000000000..74b673ebbeb9d --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sm8250-lge-timelm.dts @@ -0,0 +1,543 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2026 rofikkerneldev <rofikcoga@gmail.com> + * Device Tree for LG V60 ThinQ 5G (timelm / LM-V600) + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/phy/phy.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> +#include <dt-bindings/sound/qcom,q6afe.h> +#include <dt-bindings/sound/qcom,q6asm.h> +#include <dt-bindings/usb/pd.h> +#include "sm8250.dtsi" +#include "pm8150.dtsi" +#include "pm8150b.dtsi" +#include "pm8150l.dtsi" +#include "pm8009.dtsi" + +/* + * Delete upstream reserved-memory nodes that differ on LG V60. + */ +/delete-node/ &adsp_mem; +/delete-node/ &spss_mem; +/delete-node/ &cdsp_secure_heap; + +/ { + model = "LG V60 ThinQ 5G"; + compatible = "lge,timelm", "qcom,sm8250"; + chassis-type = "handset"; + + aliases { + serial0 = &uart12; + }; + + chosen { + stdout-path = "serial0:115200n8"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + framebuffer: framebuffer@9c000000 { + compatible = "simple-framebuffer"; + reg = <0 0x9c000000 0 0x1200000>; + width = <1080>; + height = <2460>; + stride = <(1080 * 4)>; + format = "a8r8g8b8"; + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&gcc GCC_DISP_HF_AXI_CLK>, + <&gcc GCC_DISP_SF_AXI_CLK>, + <&dispcc DISP_CC_MDSS_VSYNC_CLK>, + <&dispcc DISP_CC_MDSS_MDP_CLK>, + <&dispcc DISP_CC_MDSS_BYTE0_CLK>, + <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>, + <&dispcc DISP_CC_MDSS_PCLK0_CLK>, + <&dispcc DISP_CC_MDSS_ESC0_CLK>; + power-domains = <&dispcc MDSS_GDSC>; + }; + }; + + battery: battery { + compatible = "simple-battery"; + charge-full-design-microamp-hours = <4900000>; + energy-full-design-microwatt-hours = <18800000>; + voltage-min-design-microvolt = <3400000>; + voltage-max-design-microvolt = <4450000>; + }; + + gpio_keys: gpio-keys { + compatible = "gpio-keys"; + + pinctrl-0 = <&vol_up_n &hot1_key_n>; + pinctrl-names = "default"; + + key-vol-up { + label = "Volume Up"; + gpios = <&pm8150_gpios 6 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + debounce-interval = <15>; + linux,can-disable; + wakeup-source; + }; + + key-assistant { + label = "Google Assistant"; + gpios = <&pm8150_gpios 1 GPIO_ACTIVE_LOW>; + linux,code = <KEY_ASSISTANT>; + debounce-interval = <15>; + linux,can-disable; + wakeup-source; + }; + }; + + reserved-memory { + ramoops: ramoops@b0000000 { + compatible = "ramoops"; + reg = <0x0 0xb0000000 0x0 0x280000>; + record-size = <0x1000>; + console-size = <0x40000>; + ftrace-size = <0x40000>; + pmsg-size = <0x200000>; + }; + + adsp_mem: memory@8a100000 { + reg = <0x0 0x8a100000 0x0 0x2500000>; + no-map; + }; + + spss_mem: memory@8c600000 { + reg = <0x0 0x8c600000 0x0 0x100000>; + no-map; + }; + + cdsp_secure_heap: memory@8c700000 { + reg = <0x0 0x8c700000 0x0 0x4600000>; + no-map; + }; + }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + }; + + /* S6c is really ebi.lvl but it's there for supply map completeness sake. */ + vreg_s6c_0p88: smpc6-regulator { + compatible = "regulator-fixed"; + regulator-name = "vreg_s6c_0p88"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-always-on; + vin-supply = <&vph_pwr>; + }; +}; + +&apps_rsc { + regulators-0 { + compatible = "qcom,pm8150-rpmh-regulators"; + qcom,pmic-id = "a"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + vdd-s5-supply = <&vph_pwr>; + vdd-s6-supply = <&vph_pwr>; + vdd-s7-supply = <&vph_pwr>; + vdd-s8-supply = <&vph_pwr>; + vdd-s9-supply = <&vph_pwr>; + vdd-s10-supply = <&vph_pwr>; + vdd-l1-l8-l11-supply = <&vreg_s6c_0p88>; + vdd-l2-l10-supply = <&vreg_bob>; + vdd-l3-l4-l5-l18-supply = <&vreg_s6a_0p6>; + vdd-l6-l9-supply = <&vreg_s8c_1p2>; + vdd-l7-l12-l14-l15-supply = <&vreg_s5a_1p9>; + vdd-l13-l16-l17-supply = <&vreg_bob>; + + vreg_s4a_1p8: smps4 { + regulator-name = "vreg_s4a_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s5a_1p9: smps5 { + regulator-name = "vreg_s5a_1p9"; + regulator-min-microvolt = <1824000>; + regulator-max-microvolt = <2040000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s6a_0p6: smps6 { + regulator-name = "vreg_s6a_0p6"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1128000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2a_3p1: ldo2 { + regulator-name = "vreg_l2a_3p1"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3a_0p9: ldo3 { + regulator-name = "vreg_l3a_0p9"; + regulator-min-microvolt = <928000>; + regulator-max-microvolt = <932000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l5a_0p88: ldo5 { + regulator-name = "vreg_l5a_0p88"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6a_1p2: ldo6 { + regulator-name = "vreg_l6a_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9a_1p2: ldo9 { + regulator-name = "vreg_l9a_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l12a_1p8: ldo12 { + regulator-name = "vreg_l12a_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l14a_1p8: ldo14 { + regulator-name = "vreg_l14a_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l17a_3p0: ldo17 { + regulator-name = "vreg_l17a_3p0"; + regulator-min-microvolt = <2496000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l18a_0p9: ldo18 { + regulator-name = "vreg_l18a_0p9"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-1 { + compatible = "qcom,pm8150l-rpmh-regulators"; + qcom,pmic-id = "c"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + vdd-s5-supply = <&vph_pwr>; + vdd-s6-supply = <&vph_pwr>; + vdd-s7-supply = <&vph_pwr>; + vdd-s8-supply = <&vph_pwr>; + vdd-l1-l8-supply = <&vreg_s4a_1p8>; + vdd-l2-l3-supply = <&vreg_s8c_1p2>; + vdd-l4-l5-l6-supply = <&vreg_bob>; + vdd-l7-l11-supply = <&vreg_bob>; + vdd-l9-l10-supply = <&vreg_bob>; + vdd-bob-supply = <&vph_pwr>; + + vreg_bob: bob { + regulator-name = "vreg_bob"; + regulator-min-microvolt = <3350000>; + regulator-max-microvolt = <3960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; + }; + + vreg_s7c_0p35: smps7 { + regulator-name = "vreg_s7c_0p35"; + regulator-min-microvolt = <348000>; + regulator-max-microvolt = <1000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s8c_1p2: smps8 { + regulator-name = "vreg_s8c_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1400000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1c_1p8: ldo1 { + regulator-name = "vreg_l1c_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3c_1p2: ldo3 { + regulator-name = "vreg_l3c_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l5c_1p8: ldo5 { + regulator-name = "vreg_l5c_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6c_2p9: ldo6 { + regulator-name = "vreg_l6c_2p9"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7c_2p85: ldo7 { + regulator-name = "vreg_l7c_2p85"; + regulator-min-microvolt = <2856000>; + regulator-max-microvolt = <3104000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8c_1p8: ldo8 { + regulator-name = "vreg_l8c_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9c_2p9: ldo9 { + regulator-name = "vreg_l9c_2p9"; + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l10c_3p3: ldo10 { + regulator-name = "vreg_l10c_3p3"; + regulator-min-microvolt = <3296000>; + regulator-max-microvolt = <3296000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l11c_3p0: ldo11 { + regulator-name = "vreg_l11c_3p0"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-2 { + compatible = "qcom,pm8009-rpmh-regulators"; + qcom,pmic-id = "f"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vreg_bob>; + vdd-l2-supply = <&vreg_s8c_1p2>; + vdd-l5-l6-supply = <&vreg_bob>; + vdd-l7-supply = <&vreg_s4a_1p8>; + + vreg_s1f_1p2: smps1 { + regulator-name = "vreg_s1f_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s2f_0p5: smps2 { + regulator-name = "vreg_s2f_0p5"; + regulator-min-microvolt = <512000>; + regulator-max-microvolt = <1100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2f_1p3: ldo2 { + regulator-name = "vreg_l2f_1p3"; + regulator-min-microvolt = <1304000>; + regulator-max-microvolt = <1304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l4f_1p05: ldo4 { + regulator-name = "vreg_l4f_1p05"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l5f_2p8: ldo5 { + regulator-name = "vreg_l5f_2p8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6f_2p8: ldo6 { + regulator-name = "vreg_l6f_2p8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7f_1p8: ldo7 { + regulator-name = "vreg_l7f_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; +}; + +&cdsp { + status = "okay"; +}; + +&gpi_dma0 { + status = "okay"; +}; + +&gpi_dma1 { + status = "okay"; +}; + +&gpi_dma2 { + status = "okay"; +}; + +&gpu { + status = "okay"; + + zap-shader { + memory-region = <&gpu_mem>; + firmware-name = "qcom/sm8250/a650_zap.mbn"; + }; +}; + +&pm8150_gpios { + hot1_key_n: hot1-key-n-state { + pins = "gpio1"; + function = "normal"; + bias-pull-up; + input-enable; + power-source = <0>; + }; + + vol_up_n: vol-up-n-state { + pins = "gpio6"; + function = "normal"; + bias-pull-up; + input-enable; + power-source = <0>; + }; +}; + +&pon { + mode-bootloader = <0x2>; + mode-recovery = <0x1>; +}; + +&pon_pwrkey { + status = "okay"; +}; + +&pon_resin { + status = "okay"; + linux,code = <KEY_VOLUMEDOWN>; +}; + +&qupv3_id_0 { + status = "okay"; +}; + +&qupv3_id_1 { + status = "okay"; +}; + +&qupv3_id_2 { + status = "okay"; +}; + +&uart12 { + status = "okay"; +}; + +&ufs_mem_hc { + status = "okay"; + + vcc-supply = <&vreg_l17a_3p0>; + vcc-max-microamp = <800000>; + vccq-supply = <&vreg_l6a_1p2>; + vccq-max-microamp = <800000>; + vccq2-supply = <&vreg_s4a_1p8>; + vccq2-max-microamp = <800000>; +}; + +&ufs_mem_phy { + status = "okay"; + + vdda-phy-supply = <&vreg_l5a_0p88>; + vdda-pll-supply = <&vreg_l9a_1p2>; +}; + +&sdhc_2 { + status = "okay"; + + cd-gpios = <&tlmm 77 GPIO_ACTIVE_LOW>; + vmmc-supply = <&vreg_l9c_2p9>; + vqmmc-supply = <&vreg_l6c_2p9>; + bus-width = <4>; + no-sdio; + no-mmc; +}; + +&usb_1 { + status = "okay"; +}; + +&usb_1_dwc3 { + dr_mode = "peripheral"; +}; + +&usb_1_hsphy { + status = "okay"; + + vdda-pll-supply = <&vreg_l5a_0p88>; + vdda18-supply = <&vreg_l12a_1p8>; + vdda33-supply = <&vreg_l2a_3p1>; +}; + +&usb_1_qmpphy { + status = "okay"; + + vdda-phy-supply = <&vreg_l9a_1p2>; + vdda-pll-supply = <&vreg_l18a_0p9>; +}; -- 2.39.5 ^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v1 03/11] arm64: dts: qcom: sm8250-lge-timelm: add reserved memory regions 2026-11-17 12:39 [PATCH v1 00/11] arm64: qcom: Add initial support for LG V60 ThinQ 5G (timelm) rofikkerneldev 2026-11-17 12:39 ` [PATCH v1 01/11] dt-bindings: arm: qcom: add " rofikkerneldev 2026-11-17 12:39 ` [PATCH v1 02/11] arm64: dts: qcom: add LG V60 ThinQ 5G (timelm) support rofikkerneldev @ 2026-11-17 12:39 ` rofikkerneldev 2026-11-17 12:39 ` [PATCH v1 04/11] dt-bindings: display: panel: add LG SW43103 rofikkerneldev ` (7 subsequent siblings) 10 siblings, 0 replies; 12+ messages in thread From: rofikkerneldev @ 2026-11-17 12:39 UTC (permalink / raw) To: linux-arm-msm Cc: devicetree, dri-devel, linux-input, linux-kernel, Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Neil Armstrong, Dmitry Torokhov, rofikkerneldev Reserve the XBL/UEFI log and DFPS data regions used by the firmware. Keep these regions protected from kernel reuse. Signed-off-by: rofikkerneldev <rofikcoga@gmail.com> --- arch/arm64/boot/dts/qcom/sm8250-lge-timelm.dts | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sm8250-lge-timelm.dts b/arch/arm64/boot/dts/qcom/sm8250-lge-timelm.dts index 74b673ebbeb9d..ecbff27976fc2 100644 --- a/arch/arm64/boot/dts/qcom/sm8250-lge-timelm.dts +++ b/arch/arm64/boot/dts/qcom/sm8250-lge-timelm.dts @@ -103,6 +103,12 @@ ramoops: ramoops@b0000000 { console-size = <0x40000>; ftrace-size = <0x40000>; pmsg-size = <0x200000>; + no-map; + }; + + res_xbl_uefi_log_region: memory@80880000 { + reg = <0x0 0x80880000 0x0 0x14000>; + no-map; }; adsp_mem: memory@8a100000 { @@ -119,6 +125,16 @@ cdsp_secure_heap: memory@8c700000 { reg = <0x0 0x8c700000 0x0 0x4600000>; no-map; }; + + cont_splash_mem: memory@9c000000 { + reg = <0x0 0x9c000000 0x0 0x1200000>; + no-map; + }; + + dfps_data_mem: memory@9e300000 { + reg = <0x0 0x9e300000 0x0 0x100000>; + no-map; + }; }; vph_pwr: vph-pwr-regulator { -- 2.39.5 ^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v1 04/11] dt-bindings: display: panel: add LG SW43103 2026-11-17 12:39 [PATCH v1 00/11] arm64: qcom: Add initial support for LG V60 ThinQ 5G (timelm) rofikkerneldev ` (2 preceding siblings ...) 2026-11-17 12:39 ` [PATCH v1 03/11] arm64: dts: qcom: sm8250-lge-timelm: add reserved memory regions rofikkerneldev @ 2026-11-17 12:39 ` rofikkerneldev 2026-11-17 12:39 ` [PATCH v1 05/11] drm/panel: add LG SW43103 panel driver rofikkerneldev ` (6 subsequent siblings) 10 siblings, 0 replies; 12+ messages in thread From: rofikkerneldev @ 2026-11-17 12:39 UTC (permalink / raw) To: linux-arm-msm Cc: devicetree, dri-devel, linux-input, linux-kernel, Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Neil Armstrong, Dmitry Torokhov, rofikkerneldev Document the SW43103 FHD+ AMOLED panel used by the LG V60. The panel uses DSI command mode with DSC and DCS backlight control. Signed-off-by: rofikkerneldev <rofikcoga@gmail.com> --- .../bindings/display/panel/lg,sw43103.yaml | 70 +++++++++++++++++++ MAINTAINERS | 5 ++ 2 files changed, 75 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/panel/lg,sw43103.yaml diff --git a/Documentation/devicetree/bindings/display/panel/lg,sw43103.yaml b/Documentation/devicetree/bindings/display/panel/lg,sw43103.yaml new file mode 100644 index 0000000000000..edd007e2c0d76 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/lg,sw43103.yaml @@ -0,0 +1,70 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/lg,sw43103.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: LG / BOE SW43103 1080x2460 DSI cmd mode panel + +maintainers: + - rofikkerneldev <rofikcoga@gmail.com> + +description: + This panel is used on the LG V60 ThinQ 5G (timelm). It is a 60 Hz FHD+ AMOLED + panel driven by a Silicon Works SW43103 DDIC, operating in DSI Command Mode + with DSC (Display Stream Compression). + +allOf: + - $ref: panel-common.yaml# + +properties: + compatible: + enum: + - lg,sw43103 + - boe,sw43103 + + reg: + maxItems: 1 + + port: true + vddi-supply: true + vpnl-supply: true + reset-gpios: true + enable-gpios: true + +required: + - compatible + - reg + - vddi-supply + - vpnl-supply + - reset-gpios + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + dsi { + #address-cells = <1>; + #size-cells = <0>; + + panel@0 { + compatible = "lg,sw43103"; + reg = <0>; + + vddi-supply = <&vreg_l14a_1p8>; + vpnl-supply = <&vreg_l11c_3p0>; + + reset-gpios = <&tlmm 75 GPIO_ACTIVE_LOW>; + enable-gpios = <&pm8150l_gpios 4 GPIO_ACTIVE_HIGH>; + + port { + endpoint { + remote-endpoint = <&mdss_dsi0_out>; + }; + }; + }; + }; +... diff --git a/MAINTAINERS b/MAINTAINERS index 315a4a000b405..bca5065166c25 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -15231,6 +15231,11 @@ Q: http://patchwork.linuxtv.org/project/linux-media/list/ T: git git://linuxtv.org/mkrufky/tuners.git F: drivers/media/dvb-frontends/lgdt3305.* +LG SW43103 PANEL DRIVER +M: rofikkerneldev <rofikcoga@gmail.com> +S: Maintained +F: Documentation/devicetree/bindings/display/panel/lg,sw43103.yaml + LG V60 THINQ 5G (TIMELM) SUPPORT M: rofikkerneldev <rofikcoga@gmail.com> L: linux-arm-msm@vger.kernel.org -- 2.39.5 ^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v1 05/11] drm/panel: add LG SW43103 panel driver 2026-11-17 12:39 [PATCH v1 00/11] arm64: qcom: Add initial support for LG V60 ThinQ 5G (timelm) rofikkerneldev ` (3 preceding siblings ...) 2026-11-17 12:39 ` [PATCH v1 04/11] dt-bindings: display: panel: add LG SW43103 rofikkerneldev @ 2026-11-17 12:39 ` rofikkerneldev 2026-11-17 12:39 ` [PATCH v1 06/11] dt-bindings: input: touchscreen: add Silicon Works SW42902 rofikkerneldev ` (5 subsequent siblings) 10 siblings, 0 replies; 12+ messages in thread From: rofikkerneldev @ 2026-11-17 12:39 UTC (permalink / raw) To: linux-arm-msm Cc: devicetree, dri-devel, linux-input, linux-kernel, Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Neil Armstrong, Dmitry Torokhov, rofikkerneldev Add support for the 1080x2460 SW43103 AMOLED panel. Handle power and reset sequencing, DCS backlight control, and the DSC configuration required by the panel. Signed-off-by: rofikkerneldev <rofikcoga@gmail.com> --- MAINTAINERS | 1 + drivers/gpu/drm/panel/Kconfig | 13 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-lg-sw43103.c | 594 +++++++++++++++++++++++ 4 files changed, 609 insertions(+) create mode 100644 drivers/gpu/drm/panel/panel-lg-sw43103.c diff --git a/MAINTAINERS b/MAINTAINERS index bca5065166c25..abdaabe16ed53 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -15235,6 +15235,7 @@ LG SW43103 PANEL DRIVER M: rofikkerneldev <rofikcoga@gmail.com> S: Maintained F: Documentation/devicetree/bindings/display/panel/lg,sw43103.yaml +F: drivers/gpu/drm/panel/panel-lg-sw43103.c LG V60 THINQ 5G (TIMELM) SUPPORT M: rofikkerneldev <rofikcoga@gmail.com> diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig index 7a520b4d60fef..e765b9c7b02e6 100644 --- a/drivers/gpu/drm/panel/Kconfig +++ b/drivers/gpu/drm/panel/Kconfig @@ -540,6 +540,19 @@ config DRM_PANEL_LG_LG4573 Say Y here if you want to enable support for LG4573 RGB panel. To compile this driver as a module, choose M here. +config DRM_PANEL_LG_SW43103 + tristate "LG / BOE SW43103 panel" + depends on OF + depends on DRM_MIPI_DSI + depends on BACKLIGHT_CLASS_DEVICE + select DRM_DISPLAY_DSC_HELPER + select DRM_DISPLAY_HELPER + help + Say Y here if you want to enable support for LG / BOE SW43103 panel. + The panel has a 1080x2460@60Hz resolution and uses DSC command mode. + It is used on devices such as the LG V60 ThinQ 5G (timelm). + To compile this driver as a module, choose M here. + config DRM_PANEL_LG_SW43408 tristate "LG SW43408 panel" depends on GPIOLIB diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile index da5175909d540..c6f3280cd5828 100644 --- a/drivers/gpu/drm/panel/Makefile +++ b/drivers/gpu/drm/panel/Makefile @@ -53,6 +53,7 @@ obj-$(CONFIG_DRM_PANEL_LINCOLNTECH_LCD197) += panel-lincolntech-lcd197.o obj-$(CONFIG_DRM_PANEL_LG_LB035Q02) += panel-lg-lb035q02.o obj-$(CONFIG_DRM_PANEL_LG_LD070WX3) += panel-lg-ld070wx3.o obj-$(CONFIG_DRM_PANEL_LG_LG4573) += panel-lg-lg4573.o +obj-$(CONFIG_DRM_PANEL_LG_SW43103) += panel-lg-sw43103.o obj-$(CONFIG_DRM_PANEL_LG_SW43408) += panel-lg-sw43408.o obj-$(CONFIG_DRM_PANEL_LXD_M9189A) += panel-lxd-m9189a.o obj-$(CONFIG_DRM_PANEL_MAGNACHIP_D53E6EA8966) += panel-magnachip-d53e6ea8966.o diff --git a/drivers/gpu/drm/panel/panel-lg-sw43103.c b/drivers/gpu/drm/panel/panel-lg-sw43103.c new file mode 100644 index 0000000000000..caab54e0d1153 --- /dev/null +++ b/drivers/gpu/drm/panel/panel-lg-sw43103.c @@ -0,0 +1,594 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2026 Rofik Kernel <rofikcoga@gmail.com> + * Panel driver for LG / BOE SW43103 FHD+ DSC Command Mode AMOLED panel + * (LG V60 ThinQ 5G - timelm) + */ + +#include <linux/backlight.h> +#include <linux/delay.h> +#include <linux/gpio/consumer.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/regulator/consumer.h> + +#include <video/mipi_display.h> + +#include <drm/drm_mipi_dsi.h> +#include <drm/drm_panel.h> +#include <drm/drm_probe_helper.h> +#include <drm/display/drm_dsc.h> +#include <drm/display/drm_dsc_helper.h> + +#define NUM_SUPPLIES 2 + +struct sw43103_panel { + struct drm_panel base; + struct mipi_dsi_device *link; + + struct regulator_bulk_data supplies[NUM_SUPPLIES]; + + struct gpio_desc *reset_gpio; + struct gpio_desc *enable_gpio; + + struct drm_dsc_config dsc; +}; + +static inline struct sw43103_panel *to_panel_info(struct drm_panel *panel) +{ + return container_of(panel, struct sw43103_panel, base); +} + +static void sw43103_init_sequence(struct mipi_dsi_multi_context *ctx) +{ + /* Manufacturer Command Protect Unlock */ + mipi_dsi_dcs_write_seq_multi(ctx, 0xb0, 0xa1); + + /* Column Address Set: 0 to 1079 (0x0437) */ + mipi_dsi_dcs_write_seq_multi(ctx, MIPI_DCS_SET_COLUMN_ADDRESS, + 0x00, 0x00, 0x04, 0x37); + + /* Page Address Set: 0 to 2459 (0x099b) */ + mipi_dsi_dcs_write_seq_multi(ctx, MIPI_DCS_SET_PAGE_ADDRESS, + 0x00, 0x00, 0x09, 0x9b); + + /* HBM Mode2 */ + mipi_dsi_dcs_write_seq_multi(ctx, 0x55, 0x08); + + /* Partial Address Row Set: 0 to 2459 */ + mipi_dsi_dcs_write_seq_multi(ctx, MIPI_DCS_SET_PARTIAL_ROWS, + 0x00, 0x00, 0x09, 0x9b); + + /* Partial Address Column Set: 0 to 1079 */ + mipi_dsi_dcs_write_seq_multi(ctx, MIPI_DCS_SET_PARTIAL_COLUMNS, + 0x00, 0x00, 0x04, 0x37); + + /* Tear Effect On */ + mipi_dsi_dcs_set_tear_on_multi(ctx, MIPI_DSI_DCS_TEAR_MODE_VBLANK); + + /* Manufacturer Command Protect */ + mipi_dsi_dcs_write_seq_multi(ctx, 0xb0, 0xca); + + /* Sleep Out */ + mipi_dsi_dcs_exit_sleep_mode_multi(ctx); + mipi_dsi_msleep(ctx, 120); + + /* MCS Lv1 */ + mipi_dsi_dcs_write_seq_multi(ctx, 0xb0, 0xa1); + + /* Workaround for AOD VBP Issue */ + mipi_dsi_dcs_write_seq_multi(ctx, 0xb3, + 0x91, 0x49, 0x00, 0x0f, 0x0c, 0x00, + 0x0f, 0x0c, 0x28, 0x00, 0x02, 0x14); + + /* Global IRC */ + mipi_dsi_dcs_write_seq_multi(ctx, 0xb0, 0xa5); + mipi_dsi_dcs_write_seq_multi(ctx, 0xb1, + 0x61, 0xc0, 0x00, 0x00, 0x00, 0x10, 0xff); + mipi_dsi_dcs_write_seq_multi(ctx, 0xb2, + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + 0x00, 0xea, 0x6b, 0x60, 0x58, 0x50, 0x49, 0x41, + 0x3a, 0x33, 0x2c, 0x25, 0x1e, 0x17, 0x11, 0x0b, + 0x05, 0x6c, 0x61, 0x58, 0x50, 0x48, 0x40, 0x38, + 0x31, 0x29, 0x22, 0x1b, 0x14, 0x0d, 0x06, 0x00, + 0x62, 0x57, 0x4d, 0x44, 0x3c); + mipi_dsi_dcs_write_seq_multi(ctx, 0xb3, + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + 0x00, 0x34, 0x2d, 0x25, 0x1e, 0x16, 0x0f, 0x08, + 0x01, 0x00, 0x57, 0x4c, 0x42, 0x3a, 0x31, 0x29, + 0x22, 0x1a, 0x12, 0x0b, 0x03, 0x00, 0x00, 0x4c, + 0x42, 0x38, 0x2e, 0x26, 0x1e, 0x16, 0x0e, 0x07, + 0x00, 0x00, 0x00, 0x45, 0x39); + mipi_dsi_dcs_write_seq_multi(ctx, 0xb4, + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + 0x00, 0x2f, 0x25, 0x1c, 0x14, 0x0c, 0x04, 0x00, + 0x00, 0x00, 0x34, 0x2a, 0x21, 0x19, 0x10, 0x09, + 0x01, 0x00, 0x00, 0x00, 0x2e, 0x23, 0x19, 0x10, + 0x08, 0x00, 0x00, 0x00, 0x00, 0x25, 0x1b, 0x11, + 0x08, 0x00, 0x00, 0x00, 0x00); + mipi_dsi_dcs_write_seq_multi(ctx, 0xb5, + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x1f, + 0x13, 0x09, 0x00, 0x00, 0x00, 0x00, 0x16, 0x0c, + 0x03, 0x00, 0x00, 0x00, 0x0e, 0x06, 0x00, 0x00, + 0x00, 0x0b, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + 0x00, 0x00, 0x00); + mipi_dsi_dcs_write_seq_multi(ctx, 0xb6, + 0x44, 0x31, 0x10, 0x00, 0x00, 0x64, 0x00, 0x59, + 0xf3, 0x10, 0x80, 0x30, 0x20, 0x00, 0x00, 0x00, + 0x00, 0x00, 0x00, 0x00, 0x00); + + /* Global IRC DCC Control */ + mipi_dsi_dcs_write_seq_multi(ctx, 0xd1, + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + 0x00, 0x00, 0x00, 0x00, 0x00, 0xd0, 0x10, 0x02, + 0x00, 0x00, 0x00); + + /* V256 Enable */ + mipi_dsi_dcs_write_seq_multi(ctx, 0xb0, 0xa3); + mipi_dsi_dcs_write_seq_multi(ctx, 0xee, 0x02, 0x00, 0x00); + + /* Gamma Band 1 */ + mipi_dsi_dcs_write_seq_multi(ctx, 0xb8, + 0x00, 0x00, 0x83, 0xff, 0x5c, 0x96, 0xf2, 0x29, + 0x84, 0xb4, 0xd2, 0x77, 0x70, 0xa3, 0xcb, 0xe4); + mipi_dsi_dcs_write_seq_multi(ctx, 0xb9, + 0x00, 0x00, 0x02, 0xff, 0x4d, 0xd7, 0xb4, 0xfe, + 0x66, 0xa0, 0xca, 0x6f, 0x6f, 0xa8, 0xce, 0xe6); + mipi_dsi_dcs_write_seq_multi(ctx, 0xba, + 0x00, 0x00, 0x84, 0xff, 0x89, 0x3d, 0xec, 0x28, + 0x83, 0xae, 0xd2, 0x7e, 0x77, 0xa8, 0xcb, 0xe0); + + /* Gamma Band 2 */ + mipi_dsi_dcs_write_seq_multi(ctx, 0xbb, + 0x00, 0x13, 0x83, 0xff, 0x61, 0x66, 0xed, 0x24, + 0x81, 0xaf, 0xd4, 0x7b, 0x6b, 0xa8, 0xce, 0xe4); + mipi_dsi_dcs_write_seq_multi(ctx, 0xbc, + 0x00, 0x13, 0x02, 0xff, 0x53, 0xb4, 0xad, 0xf4, + 0x5e, 0x9d, 0xc7, 0x71, 0x68, 0xaa, 0xcf, 0xe6); + mipi_dsi_dcs_write_seq_multi(ctx, 0xbd, + 0x00, 0x13, 0x84, 0xff, 0x8a, 0x05, 0xea, 0x23, + 0x80, 0xaf, 0xd3, 0x82, 0x74, 0xab, 0xce, 0xe3); + + /* Gamma Band 3 */ + mipi_dsi_dcs_write_seq_multi(ctx, 0xbe, + 0x00, 0x37, 0x83, 0xff, 0x77, 0x5c, 0xdd, 0x15, + 0x79, 0xaf, 0xcf, 0x72, 0x6f, 0xa7, 0xce, 0xe5); + mipi_dsi_dcs_write_seq_multi(ctx, 0xbf, + 0x00, 0x37, 0x02, 0xff, 0x65, 0xaa, 0xa0, 0xe5, + 0x52, 0x96, 0xc4, 0x64, 0x6b, 0xa9, 0xcf, 0xe7); + mipi_dsi_dcs_write_seq_multi(ctx, 0xc0, + 0x00, 0x37, 0x83, 0xff, 0x9d, 0xfd, 0xd8, 0x1c, + 0x7c, 0xac, 0xd0, 0x7b, 0x78, 0xac, 0xce, 0xe4); + + /* Gamma Band 4 */ + mipi_dsi_dcs_write_seq_multi(ctx, 0xc1, + 0x02, 0x24, 0x82, 0xff, 0x7e, 0xf1, 0xcc, 0x05, + 0x6e, 0xa4, 0xca, 0x6f, 0x6e, 0xab, 0xd2, 0xe8); + mipi_dsi_dcs_write_seq_multi(ctx, 0xc2, + 0x02, 0x24, 0x02, 0xff, 0x6e, 0x58, 0xa3, 0xd5, + 0x3d, 0x8c, 0xbc, 0x59, 0x66, 0xaa, 0xd2, 0xe8); + mipi_dsi_dcs_write_seq_multi(ctx, 0xc3, + 0x02, 0x24, 0x83, 0xff, 0x9e, 0x7e, 0xc5, 0x10, + 0x72, 0xab, 0xcd, 0x78, 0x79, 0xb0, 0xd5, 0xe9); + + /* Gamma Band 5 */ + mipi_dsi_dcs_write_seq_multi(ctx, 0xc4, + 0x04, 0x0f, 0x02, 0xff, 0x88, 0xa4, 0xc4, 0xe9, + 0x60, 0xa0, 0xc8, 0x64, 0x6b, 0xac, 0xd3, 0xe9); + mipi_dsi_dcs_write_seq_multi(ctx, 0xc5, + 0x04, 0x0f, 0x02, 0xff, 0x7a, 0x20, 0xac, 0xca, + 0x30, 0x7d, 0xb6, 0x4a, 0x5c, 0xa8, 0xd2, 0xe9); + mipi_dsi_dcs_write_seq_multi(ctx, 0xc6, + 0x04, 0x0f, 0x03, 0xff, 0xa8, 0x2e, 0xbd, 0xfa, + 0x65, 0xa3, 0xcc, 0x6e, 0x76, 0xb3, 0xd6, 0xea); + + /* Gamma Band 6 */ + mipi_dsi_dcs_write_seq_multi(ctx, 0xc7, + 0x06, 0x12, 0x02, 0xff, 0x99, 0x7d, 0xbc, 0xde, + 0x51, 0x8e, 0xc6, 0x58, 0x63, 0xaa, 0xd2, 0xe9); + mipi_dsi_dcs_write_seq_multi(ctx, 0xc8, + 0x06, 0x12, 0x02, 0xff, 0x8d, 0x02, 0x9a, 0xcf, + 0x1e, 0x6b, 0xb0, 0x37, 0x50, 0xa3, 0xd0, 0xe7); + mipi_dsi_dcs_write_seq_multi(ctx, 0xc9, + 0x06, 0x12, 0x03, 0xff, 0xbc, 0x04, 0xb3, 0xdb, + 0x63, 0x8f, 0xc6, 0x67, 0x6f, 0xb1, 0xd5, 0xea); + + /* Gamma Band 7 */ + mipi_dsi_dcs_write_seq_multi(ctx, 0xca, + 0x08, 0x0a, 0x02, 0xff, 0xa3, 0x44, 0xca, 0xda, + 0x2d, 0x8d, 0xbc, 0x4c, 0x5a, 0xa7, 0xd0, 0xea); + mipi_dsi_dcs_write_seq_multi(ctx, 0xcb, + 0x08, 0x0a, 0x01, 0xff, 0x97, 0xd5, 0xb4, 0xdb, + 0x21, 0x6f, 0xa1, 0x24, 0x42, 0x9d, 0xcd, 0xe7); + mipi_dsi_dcs_write_seq_multi(ctx, 0xcc, + 0x08, 0x0a, 0x02, 0xff, 0xc6, 0xc5, 0xb8, 0xc7, + 0x46, 0x98, 0xbd, 0x5a, 0x68, 0xaf, 0xd4, 0xea); + + /* Gamma Band 8 */ + mipi_dsi_dcs_write_seq_multi(ctx, 0xcd, + 0x0c, 0x02, 0x01, 0xff, 0xb2, 0xfd, 0xac, 0xd5, + 0x25, 0x6d, 0xb7, 0x3b, 0x45, 0x9e, 0xd0, 0xe6); + mipi_dsi_dcs_write_seq_multi(ctx, 0xce, + 0x0c, 0x02, 0x01, 0xff, 0xa5, 0x9a, 0xac, 0xe2, + 0x31, 0x68, 0xab, 0x0e, 0x2a, 0x90, 0xc9, 0xe3); + mipi_dsi_dcs_write_seq_multi(ctx, 0xcf, + 0x0c, 0x02, 0x02, 0xff, 0xd5, 0x74, 0xad, 0xe6, + 0x2f, 0x7c, 0xbf, 0x43, 0x58, 0xa6, 0xd3, 0xe9); + + /* Gamma Band 9 */ + mipi_dsi_dcs_write_seq_multi(ctx, 0xd0, + 0x12, 0x00, 0x01, 0xff, 0xc8, 0x97, 0x01, 0xb6, + 0x0b, 0x82, 0xab, 0x0a, 0x26, 0x8d, 0xc7, 0xe4); + mipi_dsi_dcs_write_seq_multi(ctx, 0xd1, + 0x12, 0x00, 0x01, 0xff, 0xbe, 0x4a, 0x01, 0xc0, + 0x44, 0x80, 0xb3, 0x03, 0x06, 0x76, 0xba, 0xde); + mipi_dsi_dcs_write_seq_multi(ctx, 0xd2, + 0x12, 0x00, 0x02, 0xff, 0xf2, 0x00, 0x01, 0xb1, + 0x11, 0x5f, 0xa8, 0x16, 0x30, 0x94, 0xc8, 0xe7); + + /* Gamma Band 10 */ + mipi_dsi_dcs_write_seq_multi(ctx, 0xd3, + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00); + mipi_dsi_dcs_write_seq_multi(ctx, 0xd4, + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00); + mipi_dsi_dcs_write_seq_multi(ctx, 0xd5, + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00); + + mipi_dsi_dcs_write_seq_multi(ctx, 0xb0, 0xa5); + mipi_dsi_dcs_write_seq_multi(ctx, 0xcd, + 0x10, 0x12, 0x01, 0x5a, 0x90, 0x00, 0x00, 0x00, + 0x00, 0x00, 0x5d); + + mipi_dsi_dcs_write_seq_multi(ctx, 0xb0, 0xa1); + mipi_dsi_dcs_write_seq_multi(ctx, 0x55, + 0x08, 0x00, 0x82, 0xa8, 0x1c, 0x61, 0x0a, 0x90, + 0x04, 0x00); + + /* Dimming Frame Setting */ + mipi_dsi_dcs_write_seq_multi(ctx, 0xb0, 0xa3); + mipi_dsi_dcs_write_seq_multi(ctx, 0xb3, + 0x1f, 0x63, 0x00, 0x00, 0x06); + + /* Default Color Mode (Natural) */ + mipi_dsi_dcs_write_seq_multi(ctx, 0x53, 0x84); + mipi_dsi_dcs_write_seq_multi(ctx, 0xb0, 0xa4); + mipi_dsi_dcs_write_seq_multi(ctx, 0xb4, + 0x00, 0x03, 0x05, 0xaf, 0x03, 0x05, 0xaf, 0x03, + 0x05, 0xaf); + mipi_dsi_dcs_write_seq_multi(ctx, 0xb5, + 0x00, 0xff, 0x94, 0x1f, 0xae, 0x37, 0xae, 0x1f, + 0x94, 0x00, 0xfb, 0x94, 0x1e, 0xad, 0x35, 0xab, + 0x1c, 0x90, 0x00, 0xdd, 0x8f, 0x16, 0x9f, 0x24, + 0x97, 0x04, 0x75); + mipi_dsi_dcs_write_seq_multi(ctx, 0xb7, + 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, + 0x80, 0x80, 0x80, 0x80); + mipi_dsi_dcs_write_seq_multi(ctx, 0xb8, + 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, + 0x80, 0x80, 0x80, 0x80); + mipi_dsi_dcs_write_seq_multi(ctx, 0xb9, + 0x35, 0x2d, 0x2d, 0x37, 0x34, 0x35, 0x36, 0x36, + 0x36, 0x2d, 0x35, 0x33); + mipi_dsi_dcs_write_seq_multi(ctx, 0xba, + 0x80, 0x80, 0x80, 0x80, 0x88, 0x80, 0x80, 0x80, + 0x80, 0x80, 0x80, 0x7d); + mipi_dsi_dcs_write_seq_multi(ctx, 0xbb, + 0x80, 0x5a, 0x7b, 0x95, 0x65, 0x70, 0x96, 0x90, + 0x90, 0x90, 0x83, 0x72); + + /* DCC(GCC) Off */ + mipi_dsi_dcs_write_seq_multi(ctx, 0xb0, 0xa1); + mipi_dsi_dcs_write_seq_multi(ctx, 0xc2, + 0xf3, 0x20, 0x00, 0x00, 0x1d); + mipi_dsi_dcs_write_seq_multi(ctx, 0xb0, 0xa5); + mipi_dsi_dcs_write_seq_multi(ctx, 0xd1, + 0x0a, 0x00, 0x01); + mipi_dsi_msleep(ctx, 20); + mipi_dsi_dcs_write_seq_multi(ctx, 0xd1, + 0x02, 0x00, 0x01); + mipi_dsi_dcs_write_seq_multi(ctx, 0xd1, + 0x00, 0x00, 0x01); +} + +static int sw43103_program(struct drm_panel *panel) +{ + struct sw43103_panel *sw43103 = to_panel_info(panel); + struct mipi_dsi_multi_context ctx = { .dsi = sw43103->link }; + struct drm_dsc_picture_parameter_set pps; + + sw43103_init_sequence(&ctx); + + /* Transmit PPS in high speed mode */ + sw43103->link->mode_flags &= ~MIPI_DSI_MODE_LPM; + + drm_dsc_pps_payload_pack(&pps, sw43103->link->dsc); + + mipi_dsi_picture_parameter_set_multi(&ctx, &pps); + + /* Switch back to low power mode for DSC compression enable */ + sw43103->link->mode_flags |= MIPI_DSI_MODE_LPM; + + /* Enable DSC compression mode with PPS 0 */ + mipi_dsi_compression_mode_ext_multi(&ctx, true, + MIPI_DSI_COMPRESSION_DSC, 0); + + return ctx.accum_err; +} + +static int sw43103_prepare(struct drm_panel *panel) +{ + struct sw43103_panel *ctx = to_panel_info(panel); + int ret; + + ret = regulator_bulk_enable(ARRAY_SIZE(ctx->supplies), ctx->supplies); + if (ret < 0) + return ret; + + if (ctx->enable_gpio) + gpiod_set_value_cansleep(ctx->enable_gpio, 1); + + usleep_range(5000, 6000); + + /* Hardware reset sequence: deassert, assert 2ms, deassert */ + gpiod_set_value_cansleep(ctx->reset_gpio, 0); + usleep_range(10000, 11000); + gpiod_set_value_cansleep(ctx->reset_gpio, 1); + usleep_range(2000, 3000); + gpiod_set_value_cansleep(ctx->reset_gpio, 0); + usleep_range(10000, 11000); + + ret = sw43103_program(panel); + if (ret) + goto poweroff; + + return 0; + +poweroff: + gpiod_set_value_cansleep(ctx->reset_gpio, 1); + if (ctx->enable_gpio) + gpiod_set_value_cansleep(ctx->enable_gpio, 0); + regulator_bulk_disable(ARRAY_SIZE(ctx->supplies), ctx->supplies); + return ret; +} + +static int sw43103_enable(struct drm_panel *panel) +{ + struct sw43103_panel *sw43103 = to_panel_info(panel); + struct mipi_dsi_multi_context ctx = { .dsi = sw43103->link }; + + /* Display On */ + mipi_dsi_dcs_set_display_on_multi(&ctx); + mipi_dsi_msleep(&ctx, 20); + + /* Enable display backlight control and full brightness */ + mipi_dsi_dcs_write_seq_multi(&ctx, MIPI_DCS_WRITE_CONTROL_DISPLAY, 0x2c); + mipi_dsi_dcs_write_seq_multi(&ctx, MIPI_DCS_SET_DISPLAY_BRIGHTNESS, 0x07, 0xff); + + return ctx.accum_err; +} + +static int sw43103_disable(struct drm_panel *panel) +{ + struct sw43103_panel *sw43103 = to_panel_info(panel); + struct mipi_dsi_multi_context ctx = { .dsi = sw43103->link }; + + /* Display Off (0x28) */ + mipi_dsi_dcs_set_display_off_multi(&ctx); + mipi_dsi_msleep(&ctx, 20); + + /* Sleep In (0x10) */ + mipi_dsi_dcs_enter_sleep_mode_multi(&ctx); + mipi_dsi_msleep(&ctx, 80); + + return ctx.accum_err; +} + +static int sw43103_unprepare(struct drm_panel *panel) +{ + struct sw43103_panel *sw43103 = to_panel_info(panel); + + gpiod_set_value_cansleep(sw43103->reset_gpio, 1); + if (sw43103->enable_gpio) + gpiod_set_value_cansleep(sw43103->enable_gpio, 0); + + return regulator_bulk_disable(ARRAY_SIZE(sw43103->supplies), sw43103->supplies); +} + +static const struct drm_display_mode sw43103_mode = { + .clock = 179177, + .hdisplay = 1080, + .hsync_start = 1080 + 50, + .hsync_end = 1080 + 50 + 30, + .htotal = 1080 + 50 + 30 + 50, + .vdisplay = 2460, + .vsync_start = 2460 + 4, + .vsync_end = 2460 + 4 + 2, + .vtotal = 2460 + 4 + 2 + 2, + .width_mm = 69, + .height_mm = 158, + .type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED, +}; + +static int sw43103_get_modes(struct drm_panel *panel, + struct drm_connector *connector) +{ + return drm_connector_helper_get_modes_fixed(connector, &sw43103_mode); +} + +static int sw43103_backlight_update_status(struct backlight_device *bl) +{ + struct mipi_dsi_device *dsi = bl_get_data(bl); + u16 brightness = backlight_get_brightness(bl); + u8 ctrl = 0x2c; + int ret; + + dsi->mode_flags &= ~MIPI_DSI_MODE_LPM; + + ret = mipi_dsi_dcs_write(dsi, MIPI_DCS_WRITE_CONTROL_DISPLAY, &ctrl, sizeof(ctrl)); + if (ret < 0) + goto out; + + ret = mipi_dsi_dcs_set_display_brightness_large(dsi, brightness); + +out: + dsi->mode_flags |= MIPI_DSI_MODE_LPM; + + return ret < 0 ? ret : 0; +} + +static const struct backlight_ops sw43103_backlight_ops = { + .update_status = sw43103_backlight_update_status, +}; + +static int sw43103_backlight_init(struct sw43103_panel *ctx) +{ + struct device *dev = &ctx->link->dev; + const struct backlight_properties props = { + .type = BACKLIGHT_PLATFORM, + .brightness = 1024, + .max_brightness = 2047, + }; + + ctx->base.backlight = devm_backlight_device_register(dev, dev_name(dev), dev, + ctx->link, + &sw43103_backlight_ops, + &props); + + if (IS_ERR(ctx->base.backlight)) + return dev_err_probe(dev, PTR_ERR(ctx->base.backlight), + "Failed to create backlight\n"); + + return 0; +} + +static const struct drm_panel_funcs sw43103_funcs = { + .prepare = sw43103_prepare, + .unprepare = sw43103_unprepare, + .enable = sw43103_enable, + .disable = sw43103_disable, + .get_modes = sw43103_get_modes, +}; + +static const struct of_device_id sw43103_of_match[] = { + { .compatible = "lg,sw43103" }, + { .compatible = "boe,sw43103" }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, sw43103_of_match); + +static int sw43103_add(struct sw43103_panel *ctx) +{ + struct device *dev = &ctx->link->dev; + int ret; + + ctx->supplies[0].supply = "vddi"; /* 1.8 V */ + ctx->supplies[0].init_load_uA = 62000; + ctx->supplies[1].supply = "vpnl"; /* 3.0 V */ + ctx->supplies[1].init_load_uA = 857000; + + ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(ctx->supplies), + ctx->supplies); + if (ret < 0) + return ret; + + ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW); + if (IS_ERR(ctx->reset_gpio)) { + ret = PTR_ERR(ctx->reset_gpio); + return dev_err_probe(dev, ret, "cannot get reset gpio\n"); + } + + ctx->enable_gpio = devm_gpiod_get_optional(dev, "enable", GPIOD_OUT_LOW); + if (IS_ERR(ctx->enable_gpio)) { + ret = PTR_ERR(ctx->enable_gpio); + return dev_err_probe(dev, ret, "cannot get enable gpio\n"); + } + + ret = sw43103_backlight_init(ctx); + if (ret < 0) + return ret; + + ctx->base.prepare_prev_first = true; + + drm_panel_add(&ctx->base); + return 0; +} + +static int sw43103_probe(struct mipi_dsi_device *dsi) +{ + struct sw43103_panel *ctx; + int ret; + + ctx = devm_drm_panel_alloc(&dsi->dev, __typeof(*ctx), base, + &sw43103_funcs, DRM_MODE_CONNECTOR_DSI); + if (IS_ERR(ctx)) + return PTR_ERR(ctx); + + dsi->mode_flags = MIPI_DSI_MODE_LPM; + dsi->format = MIPI_DSI_FMT_RGB888; + dsi->lanes = 4; + + ctx->link = dsi; + mipi_dsi_set_drvdata(dsi, ctx); + + ret = sw43103_add(ctx); + if (ret < 0) + return ret; + + /* The panel works only in DSC mode. Set DSC params. */ + ctx->dsc.dsc_version_major = 1; + ctx->dsc.dsc_version_minor = 1; + + /* slice_count * slice_width == 2 * 540 = 1080 */ + ctx->dsc.pic_width = 1080; + ctx->dsc.pic_height = 2460; + ctx->dsc.slice_height = 60; + ctx->dsc.slice_width = 540; + ctx->dsc.slice_count = 2; + ctx->dsc.slice_chunk_size = 540; + ctx->dsc.bits_per_component = 8; + ctx->dsc.bits_per_pixel = 8 << 4; + ctx->dsc.block_pred_enable = true; + + dsi->dsc = &ctx->dsc; + + ret = mipi_dsi_attach(dsi); + if (ret) + drm_panel_remove(&ctx->base); + + return ret; +} + +static void sw43103_remove(struct mipi_dsi_device *dsi) +{ + struct sw43103_panel *ctx = mipi_dsi_get_drvdata(dsi); + int ret; + + ret = sw43103_unprepare(&ctx->base); + if (ret < 0) + dev_err(&dsi->dev, "failed to unprepare panel: %d\n", ret); + + ret = mipi_dsi_detach(dsi); + if (ret < 0) + dev_err(&dsi->dev, "failed to detach from DSI host: %d\n", ret); + + drm_panel_remove(&ctx->base); +} + +static struct mipi_dsi_driver sw43103_driver = { + .driver = { + .name = "panel-lg-sw43103", + .of_match_table = sw43103_of_match, + }, + .probe = sw43103_probe, + .remove = sw43103_remove, +}; +module_mipi_dsi_driver(sw43103_driver); + +MODULE_AUTHOR("rofikkerneldev <rofikcoga@gmail.com>"); +MODULE_DESCRIPTION("LG / BOE SW43103 FHD+ DSC Command Mode AMOLED panel"); +MODULE_LICENSE("GPL"); -- 2.39.5 ^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v1 06/11] dt-bindings: input: touchscreen: add Silicon Works SW42902 2026-11-17 12:39 [PATCH v1 00/11] arm64: qcom: Add initial support for LG V60 ThinQ 5G (timelm) rofikkerneldev ` (4 preceding siblings ...) 2026-11-17 12:39 ` [PATCH v1 05/11] drm/panel: add LG SW43103 panel driver rofikkerneldev @ 2026-11-17 12:39 ` rofikkerneldev 2026-11-17 12:39 ` [PATCH v1 07/11] Input: touchscreen: add Silicon Works SW42902 support rofikkerneldev ` (4 subsequent siblings) 10 siblings, 0 replies; 12+ messages in thread From: rofikkerneldev @ 2026-11-17 12:39 UTC (permalink / raw) To: linux-arm-msm Cc: devicetree, dri-devel, linux-input, linux-kernel, Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Neil Armstrong, Dmitry Torokhov, rofikkerneldev Document the I2C touchscreen and its interrupt, reset, power-enable, and panel-size properties. Signed-off-by: rofikkerneldev <rofikcoga@gmail.com> --- .../input/touchscreen/lg,sw42902.yaml | 74 +++++++++++++++++++ MAINTAINERS | 6 ++ 2 files changed, 80 insertions(+) create mode 100644 Documentation/devicetree/bindings/input/touchscreen/lg,sw42902.yaml diff --git a/Documentation/devicetree/bindings/input/touchscreen/lg,sw42902.yaml b/Documentation/devicetree/bindings/input/touchscreen/lg,sw42902.yaml new file mode 100644 index 0000000000000..c56cfb8530eeb --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/lg,sw42902.yaml @@ -0,0 +1,74 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/input/touchscreen/lg,sw42902.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Silicon Works SW42902 touchscreen + +maintainers: + - rofikkerneldev <rofikcoga@gmail.com> + +description: | + I2C touchscreen used in the LG V60 timelm JP DCM. The controller boots + its existing flash firmware; the enable GPIOs switch its 3.3 V and + 1.8 V power rails. + +allOf: + - $ref: touchscreen.yaml# + +properties: + compatible: + const: lg,sw42902 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + reset-gpios: + maxItems: 1 + description: Active-low controller reset + + vcl-gpios: + maxItems: 1 + description: Active-high enable for the 3.3 V rail + + vdd-gpios: + maxItems: 1 + description: Active-high enable for the 1.8 V rail + +required: + - compatible + - reg + - interrupts + - reset-gpios + - vcl-gpios + - vdd-gpios + - touchscreen-size-x + - touchscreen-size-y + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + touchscreen@28 { + compatible = "lg,sw42902"; + reg = <0x28>; + interrupt-parent = <&tlmm>; + interrupts = <39 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>; + vcl-gpios = <&tlmm 67 GPIO_ACTIVE_HIGH>; + vdd-gpios = <&tlmm 68 GPIO_ACTIVE_HIGH>; + touchscreen-size-x = <1080>; + touchscreen-size-y = <2460>; + }; + }; diff --git a/MAINTAINERS b/MAINTAINERS index abdaabe16ed53..f4c54d7d86bd8 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -25835,6 +25835,12 @@ S: Maintained F: Documentation/fb/sm712fb.rst F: drivers/video/fbdev/sm712* +SILICON WORKS SW42902 TOUCHSCREEN DRIVER +M: rofikkerneldev <rofikcoga@gmail.com> +L: linux-input@vger.kernel.org +S: Maintained +F: Documentation/devicetree/bindings/input/touchscreen/lg,sw42902.yaml + SILVACO I3C DUAL-ROLE MASTER M: Miquel Raynal <miquel.raynal@bootlin.com> M: Frank Li <Frank.Li@nxp.com> -- 2.39.5 ^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v1 07/11] Input: touchscreen: add Silicon Works SW42902 support 2026-11-17 12:39 [PATCH v1 00/11] arm64: qcom: Add initial support for LG V60 ThinQ 5G (timelm) rofikkerneldev ` (5 preceding siblings ...) 2026-11-17 12:39 ` [PATCH v1 06/11] dt-bindings: input: touchscreen: add Silicon Works SW42902 rofikkerneldev @ 2026-11-17 12:39 ` rofikkerneldev 2026-11-17 12:39 ` [PATCH v1 08/11] arm64: dts: qcom: sm8250-lge-timelm: enable SW43103 panel rofikkerneldev ` (3 subsequent siblings) 10 siblings, 0 replies; 12+ messages in thread From: rofikkerneldev @ 2026-11-17 12:39 UTC (permalink / raw) To: linux-arm-msm Cc: devicetree, dri-devel, linux-input, linux-kernel, Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Neil Armstrong, Dmitry Torokhov, rofikkerneldev Add basic multitouch support for the SW42902 controller. Implement the GPIO power and reset sequence and use the firmware already present in controller flash; no firmware update is performed. Signed-off-by: rofikkerneldev <rofikcoga@gmail.com> --- MAINTAINERS | 1 + drivers/input/touchscreen/Kconfig | 11 + drivers/input/touchscreen/Makefile | 1 + drivers/input/touchscreen/sw42902.c | 315 ++++++++++++++++++++++++++++ 4 files changed, 328 insertions(+) create mode 100644 drivers/input/touchscreen/sw42902.c diff --git a/MAINTAINERS b/MAINTAINERS index f4c54d7d86bd8..83bbedde94533 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -25840,6 +25840,7 @@ M: rofikkerneldev <rofikcoga@gmail.com> L: linux-input@vger.kernel.org S: Maintained F: Documentation/devicetree/bindings/input/touchscreen/lg,sw42902.yaml +F: drivers/input/touchscreen/sw42902.c SILVACO I3C DUAL-ROLE MASTER M: Miquel Raynal <miquel.raynal@bootlin.com> diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig index 9b9ae8ac3f7fd..eadba5125a225 100644 --- a/drivers/input/touchscreen/Kconfig +++ b/drivers/input/touchscreen/Kconfig @@ -1402,6 +1402,17 @@ config TOUCHSCREEN_ZINITIX To compile this driver as a module, choose M here: the module will be called zinitix. +config TOUCHSCREEN_SW42902 + tristate "Silicon Works SW42902 touchscreen" + depends on I2C + depends on GPIOLIB + help + Say Y here for the SW42902 I2C touchscreen used in the LG V60. + Basic multitouch uses the controller's existing flash firmware. + + To compile this driver as a module, choose M here: the module + will be called sw42902. + config TOUCHSCREEN_HIMAX_HX83112B tristate "Himax hx83112b touchscreen driver" depends on I2C diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile index bfd9de83389d8..ee312c2d1529c 100644 --- a/drivers/input/touchscreen/Makefile +++ b/drivers/input/touchscreen/Makefile @@ -119,3 +119,4 @@ obj-$(CONFIG_TOUCHSCREEN_IQS5XX) += iqs5xx.o obj-$(CONFIG_TOUCHSCREEN_IQS7211) += iqs7211.o obj-$(CONFIG_TOUCHSCREEN_ZINITIX) += zinitix.o obj-$(CONFIG_TOUCHSCREEN_HIMAX_HX83112B) += himax_hx83112b.o +obj-$(CONFIG_TOUCHSCREEN_SW42902) += sw42902.o diff --git a/drivers/input/touchscreen/sw42902.c b/drivers/input/touchscreen/sw42902.c new file mode 100644 index 0000000000000..7b39a97053c63 --- /dev/null +++ b/drivers/input/touchscreen/sw42902.c @@ -0,0 +1,315 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Silicon Works SW42902 touchscreen, as used by LG V60 (timelm). + * Register protocol and report layout derived from the LGE vendor driver + * (Copyright (C) 2015 LGE, author hoyeon.jang@lge.com). + * This driver uses the controller's existing flash firmware. + */ + +#include <linux/delay.h> +#include <linux/gpio/consumer.h> +#include <linux/i2c.h> +#include <linux/input/mt.h> +#include <linux/input/touchscreen.h> +#include <linux/interrupt.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/pm.h> +#include <linux/slab.h> +#include <linux/unaligned.h> + +#define SW42902_MAX_CONTACTS 10 +#define SW42902_REPORT_SIZE (12 + 24 + 12 * SW42902_MAX_CONTACTS) +#define SW42902_IC_STATUS 0x600 +#define SW42902_VERSION 0x642 +#define SW42902_DEVICE_CTL 0xc00 +#define SW42902_INTERRUPT_CTL 0xc01 +#define SW42902_DRIVING_CTL 0xc03 +#define SW42902_SERIAL_SPI_EN 0xfe4 +#define SW42902_DRIVING_STOP 0x04 +#define SW42902_DRIVING_U3 0x8303 + +struct sw42902 { + struct i2c_client *client; + struct input_dev *input; + struct touchscreen_properties prop; + struct gpio_desc *reset; + struct gpio_desc *vcl; + struct gpio_desc *vdd; + u8 report[SW42902_REPORT_SIZE]; +}; + +static int sw42902_read(struct sw42902 *ts, u16 reg, void *data, u16 len) +{ + u8 command[] = { (reg >> 8) | (len > 4 ? 0x20 : 0), reg & 0xff }; + struct i2c_msg msgs[] = { + { .addr = ts->client->addr, .len = sizeof(command), + .buf = command }, + { .addr = ts->client->addr, .flags = I2C_M_RD, + .len = len, .buf = data }, + }; + int ret; + + ret = i2c_transfer(ts->client->adapter, msgs, ARRAY_SIZE(msgs)); + if (ret < 0) + return ret; + return ret == ARRAY_SIZE(msgs) ? 0 : -EIO; +} + +static int sw42902_write(struct sw42902 *ts, u16 reg, u32 value) +{ + u8 command[6] = { 0x40 | (reg >> 8), reg & 0xff }; + int ret; + + put_unaligned_le32(value, command + 2); + ret = i2c_master_send(ts->client, command, sizeof(command)); + if (ret < 0) + return ret; + return ret == sizeof(command) ? 0 : -EIO; +} + +static void sw42902_release_contacts(struct sw42902 *ts) +{ + int i; + + for (i = 0; i < SW42902_MAX_CONTACTS; i++) { + input_mt_slot(ts->input, i); + input_mt_report_slot_state(ts->input, MT_TOOL_FINGER, false); + } + input_mt_sync_frame(ts->input); + input_sync(ts->input); +} + +static irqreturn_t sw42902_irq(int irq, void *data) +{ + struct sw42902 *ts = data; + struct input_dev *input = ts->input; + u32 status, header; + unsigned int count, i; + int ret; + + ret = sw42902_read(ts, SW42902_IC_STATUS, ts->report, + sizeof(ts->report)); + if (ret) { + dev_err_ratelimited(&ts->client->dev, "report read failed: %d\n", ret); + sw42902_release_contacts(ts); + return IRQ_HANDLED; + } + + status = get_unaligned_le32(ts->report + 4); + header = get_unaligned_le32(ts->report + 8); + /* Only normal absolute-touch reports; ignore pen/gesture/debug IRQs. */ + if (((status >> 16) & 0xf) != 5 || (header & 0xff)) + return IRQ_HANDLED; + + count = (header >> 8) & 0x1f; + if (count > SW42902_MAX_CONTACTS) { + dev_warn_ratelimited(&ts->client->dev, "invalid contact count: %u\n", count); + sw42902_release_contacts(ts); + return IRQ_HANDLED; + } + + /* A palm report cancels all active fingers. */ + if (header & BIT(31)) { + sw42902_release_contacts(ts); + return IRQ_HANDLED; + } + + for (i = 0; i < count; i++) { + const u8 *contact = ts->report + 36 + 12 * i; + u32 a = get_unaligned_le32(contact); + u32 b = get_unaligned_le32(contact + 4); + u32 c = get_unaligned_le32(contact + 8); + unsigned int id = a & 0x1f; + unsigned int event = (a >> 16) & 3; + + if (id == 15) { + sw42902_release_contacts(ts); + return IRQ_HANDLED; + } + if (id >= SW42902_MAX_CONTACTS || (event != 1 && event != 2)) + continue; + + input_mt_slot(input, id); + input_mt_report_slot_state(input, MT_TOOL_FINGER, true); + touchscreen_report_pos(input, &ts->prop, a >> 18, b & 0x3fff, true); + input_report_abs(input, ABS_MT_PRESSURE, (b >> 14) & 0xff); + input_report_abs(input, ABS_MT_TOUCH_MAJOR, (c >> 4) & 0x3fff); + input_report_abs(input, ABS_MT_TOUCH_MINOR, c >> 18); + } + + input_mt_sync_frame(input); + input_sync(input); + return IRQ_HANDLED; +} + +static void sw42902_power_off(void *data) +{ + struct sw42902 *ts = data; + + gpiod_set_value_cansleep(ts->reset, 1); + usleep_range(1000, 2000); + gpiod_set_value_cansleep(ts->vdd, 0); + usleep_range(1000, 2000); + gpiod_set_value_cansleep(ts->vcl, 0); +} + +static void sw42902_power_on(struct sw42902 *ts) +{ + gpiod_set_value_cansleep(ts->vcl, 1); + usleep_range(1000, 2000); + gpiod_set_value_cansleep(ts->vdd, 1); + usleep_range(10000, 11000); + gpiod_set_value_cansleep(ts->reset, 0); + /* Docomo downstream DT specifies a 90 ms hardware reset delay. */ + msleep(90); +} + +static int sw42902_start(struct sw42902 *ts) +{ + u8 version[4]; + int ret; + + ret = sw42902_read(ts, SW42902_VERSION, version, sizeof(version)); + if (ret) + return ret; + if (version[2] != 10 || (version[3] & 0xf) != 4) { + dev_err(&ts->client->dev, "unexpected chip/protocol: %u/%u\n", + version[2], version[3] & 0xf); + return -ENODEV; + } + + ret = sw42902_write(ts, SW42902_SERIAL_SPI_EN, 0); + if (ret) + return ret; + ret = sw42902_write(ts, SW42902_DEVICE_CTL, 1); + if (ret) + return ret; + ret = sw42902_write(ts, SW42902_INTERRUPT_CTL, 1); + if (ret) + return ret; + ret = sw42902_write(ts, SW42902_DRIVING_CTL, SW42902_DRIVING_STOP); + if (ret) + return ret; + msleep(30); + return sw42902_write(ts, SW42902_DRIVING_CTL, SW42902_DRIVING_U3); +} + +static int sw42902_probe(struct i2c_client *client) +{ + struct device *dev = &client->dev; + struct sw42902 *ts; + struct input_dev *input; + int ret; + + if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) + return -EOPNOTSUPP; + if (client->irq <= 0) + return dev_err_probe(dev, -EINVAL, "missing interrupt\n"); + + ts = devm_kzalloc(dev, sizeof(*ts), GFP_KERNEL); + if (!ts) + return -ENOMEM; + ts->client = client; + i2c_set_clientdata(client, ts); + + ts->reset = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH); + if (IS_ERR(ts->reset)) + return dev_err_probe(dev, PTR_ERR(ts->reset), "reset GPIO\n"); + ts->vcl = devm_gpiod_get(dev, "vcl", GPIOD_OUT_LOW); + if (IS_ERR(ts->vcl)) + return dev_err_probe(dev, PTR_ERR(ts->vcl), "3.3 V enable GPIO\n"); + ts->vdd = devm_gpiod_get(dev, "vdd", GPIOD_OUT_LOW); + if (IS_ERR(ts->vdd)) + return dev_err_probe(dev, PTR_ERR(ts->vdd), "1.8 V enable GPIO\n"); + ret = devm_add_action_or_reset(dev, sw42902_power_off, ts); + if (ret) + return ret; + + input = devm_input_allocate_device(dev); + if (!input) + return -ENOMEM; + ts->input = input; + input->name = "Silicon Works SW42902"; + input->id.bustype = BUS_I2C; + input_set_abs_params(input, ABS_MT_POSITION_X, 0, 1079, 0, 0); + input_set_abs_params(input, ABS_MT_POSITION_Y, 0, 2459, 0, 0); + input_set_abs_params(input, ABS_MT_PRESSURE, 0, 255, 0, 0); + input_set_abs_params(input, ABS_MT_TOUCH_MAJOR, 0, 16383, 0, 0); + input_set_abs_params(input, ABS_MT_TOUCH_MINOR, 0, 16383, 0, 0); + touchscreen_parse_properties(input, true, &ts->prop); + ret = input_mt_init_slots(input, SW42902_MAX_CONTACTS, + INPUT_MT_DIRECT | INPUT_MT_DROP_UNUSED); + if (ret) + return ret; + ret = devm_request_threaded_irq(dev, client->irq, NULL, sw42902_irq, + IRQF_ONESHOT | IRQF_NO_AUTOEN, + dev_name(dev), ts); + if (ret) + return dev_err_probe(dev, ret, "interrupt request failed\n"); + + sw42902_power_on(ts); + ret = sw42902_start(ts); + if (ret) + return dev_err_probe(dev, ret, "controller initialization failed\n"); + ret = input_register_device(input); + if (ret) + return ret; + enable_irq(client->irq); + dev_info(dev, "SW42902 initialized using existing flash firmware\n"); + return 0; +} + +static int sw42902_suspend(struct device *dev) +{ + struct sw42902 *ts = i2c_get_clientdata(to_i2c_client(dev)); + + disable_irq(ts->client->irq); + sw42902_release_contacts(ts); + sw42902_write(ts, SW42902_DRIVING_CTL, SW42902_DRIVING_STOP); + sw42902_power_off(ts); + return 0; +} + +static int sw42902_resume(struct device *dev) +{ + struct sw42902 *ts = i2c_get_clientdata(to_i2c_client(dev)); + int ret; + + sw42902_power_on(ts); + ret = sw42902_start(ts); + if (ret) { + sw42902_power_off(ts); + return ret; + } + enable_irq(ts->client->irq); + return 0; +} + +static DEFINE_SIMPLE_DEV_PM_OPS(sw42902_pm_ops, sw42902_suspend, sw42902_resume); + +static const struct of_device_id sw42902_of_match[] = { + { .compatible = "lg,sw42902" }, + { } +}; +MODULE_DEVICE_TABLE(of, sw42902_of_match); + +static const struct i2c_device_id sw42902_ids[] = { + { "sw42902" }, + { } +}; +MODULE_DEVICE_TABLE(i2c, sw42902_ids); + +static struct i2c_driver sw42902_driver = { + .driver = { + .name = "sw42902", + .of_match_table = sw42902_of_match, + .pm = pm_sleep_ptr(&sw42902_pm_ops), + }, + .probe = sw42902_probe, + .id_table = sw42902_ids, +}; +module_i2c_driver(sw42902_driver); + +MODULE_DESCRIPTION("Silicon Works SW42902 touchscreen driver"); +MODULE_LICENSE("GPL"); -- 2.39.5 ^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v1 08/11] arm64: dts: qcom: sm8250-lge-timelm: enable SW43103 panel 2026-11-17 12:39 [PATCH v1 00/11] arm64: qcom: Add initial support for LG V60 ThinQ 5G (timelm) rofikkerneldev ` (6 preceding siblings ...) 2026-11-17 12:39 ` [PATCH v1 07/11] Input: touchscreen: add Silicon Works SW42902 support rofikkerneldev @ 2026-11-17 12:39 ` rofikkerneldev 2026-11-17 12:39 ` [PATCH v1 09/11] arm64: dts: qcom: sm8250-lge-timelm: add SW42902 touchscreen rofikkerneldev ` (2 subsequent siblings) 10 siblings, 0 replies; 12+ messages in thread From: rofikkerneldev @ 2026-11-17 12:39 UTC (permalink / raw) To: linux-arm-msm Cc: devicetree, dri-devel, linux-input, linux-kernel, Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Neil Armstrong, Dmitry Torokhov, rofikkerneldev Enable DISPCC, MDSS, DSI0, and its PHY. Attach the SW43103 panel with its power rails, reset GPIO, and four-lane DSI link. Signed-off-by: rofikkerneldev <rofikcoga@gmail.com> --- .../arm64/boot/dts/qcom/sm8250-lge-timelm.dts | 39 +++++++++++++++++++ 1 file changed, 39 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sm8250-lge-timelm.dts b/arch/arm64/boot/dts/qcom/sm8250-lge-timelm.dts index ecbff27976fc2..fca48472f5dfe 100644 --- a/arch/arm64/boot/dts/qcom/sm8250-lge-timelm.dts +++ b/arch/arm64/boot/dts/qcom/sm8250-lge-timelm.dts @@ -557,3 +557,42 @@ &usb_1_qmpphy { vdda-phy-supply = <&vreg_l9a_1p2>; vdda-pll-supply = <&vreg_l18a_0p9>; }; + +&dispcc { + status = "okay"; +}; + +&mdss { + status = "okay"; +}; + +&mdss_dsi0 { + vdda-supply = <&vreg_l9a_1p2>; + status = "okay"; + + panel@0 { + compatible = "lg,sw43103"; + reg = <0>; + + vddi-supply = <&vreg_l14a_1p8>; + vpnl-supply = <&vreg_l11c_3p0>; + reset-gpios = <&tlmm 75 GPIO_ACTIVE_LOW>; + + port { + panel_in_0: endpoint { + remote-endpoint = <&mdss_dsi0_out>; + }; + }; + }; +}; + +&mdss_dsi0_out { + data-lanes = <0 1 2 3>; + remote-endpoint = <&panel_in_0>; +}; + +&mdss_dsi0_phy { + vdds-supply = <&vreg_l5a_0p88>; + phy-type = <PHY_TYPE_DPHY>; + status = "okay"; +}; -- 2.39.5 ^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v1 09/11] arm64: dts: qcom: sm8250-lge-timelm: add SW42902 touchscreen 2026-11-17 12:39 [PATCH v1 00/11] arm64: qcom: Add initial support for LG V60 ThinQ 5G (timelm) rofikkerneldev ` (7 preceding siblings ...) 2026-11-17 12:39 ` [PATCH v1 08/11] arm64: dts: qcom: sm8250-lge-timelm: enable SW43103 panel rofikkerneldev @ 2026-11-17 12:39 ` rofikkerneldev 2026-11-17 12:39 ` [PATCH v1 10/11] arm64: dts: qcom: sm8250-lge-timelm: enable USB Type-C rofikkerneldev 2026-11-17 12:39 ` [PATCH v1 11/11] arm64: dts: qcom: sm8250-lge-timelm: add QCA6390 Bluetooth rofikkerneldev 10 siblings, 0 replies; 12+ messages in thread From: rofikkerneldev @ 2026-11-17 12:39 UTC (permalink / raw) To: linux-arm-msm Cc: devicetree, dri-devel, linux-input, linux-kernel, Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Neil Armstrong, Dmitry Torokhov, rofikkerneldev Describe the SW42902 on GENI I2C13 with its interrupt, reset, power-enable GPIOs, pinctrl, and native 1080x2460 touch area. Signed-off-by: rofikkerneldev <rofikcoga@gmail.com> --- .../arm64/boot/dts/qcom/sm8250-lge-timelm.dts | 36 +++++++++++++++++++ 1 file changed, 36 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sm8250-lge-timelm.dts b/arch/arm64/boot/dts/qcom/sm8250-lge-timelm.dts index fca48472f5dfe..a094aa81ad225 100644 --- a/arch/arm64/boot/dts/qcom/sm8250-lge-timelm.dts +++ b/arch/arm64/boot/dts/qcom/sm8250-lge-timelm.dts @@ -596,3 +596,39 @@ &mdss_dsi0_phy { phy-type = <PHY_TYPE_DPHY>; status = "okay"; }; + +&i2c13 { + clock-frequency = <400000>; + status = "okay"; + + touchscreen@28 { + compatible = "lg,sw42902"; + reg = <0x28>; + + pinctrl-names = "default"; + pinctrl-0 = <&touch_reset_default &touch_irq_default>; + interrupt-parent = <&tlmm>; + interrupts = <39 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>; + vcl-gpios = <&tlmm 67 GPIO_ACTIVE_HIGH>; + vdd-gpios = <&tlmm 68 GPIO_ACTIVE_HIGH>; + touchscreen-size-x = <1080>; + touchscreen-size-y = <2460>; + }; +}; + +&tlmm { + touch_reset_default: touch-reset-default-state { + pins = "gpio38"; + function = "gpio"; + drive-strength = <6>; + bias-pull-up; + }; + + touch_irq_default: touch-irq-default-state { + pins = "gpio39"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; +}; -- 2.39.5 ^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v1 10/11] arm64: dts: qcom: sm8250-lge-timelm: enable USB Type-C 2026-11-17 12:39 [PATCH v1 00/11] arm64: qcom: Add initial support for LG V60 ThinQ 5G (timelm) rofikkerneldev ` (8 preceding siblings ...) 2026-11-17 12:39 ` [PATCH v1 09/11] arm64: dts: qcom: sm8250-lge-timelm: add SW42902 touchscreen rofikkerneldev @ 2026-11-17 12:39 ` rofikkerneldev 2026-11-17 12:39 ` [PATCH v1 11/11] arm64: dts: qcom: sm8250-lge-timelm: add QCA6390 Bluetooth rofikkerneldev 10 siblings, 0 replies; 12+ messages in thread From: rofikkerneldev @ 2026-11-17 12:39 UTC (permalink / raw) To: linux-arm-msm Cc: devicetree, dri-devel, linux-input, linux-kernel, Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Neil Armstrong, Dmitry Torokhov, rofikkerneldev Enable the PM8150B Type-C controller as a sink-only port. Keep the primary DWC3 controller in peripheral mode for now; host mode and VBUS sourcing can be enabled after OTG power delivery is validated. Signed-off-by: rofikkerneldev <rofikcoga@gmail.com> --- arch/arm64/boot/dts/qcom/sm8250-lge-timelm.dts | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sm8250-lge-timelm.dts b/arch/arm64/boot/dts/qcom/sm8250-lge-timelm.dts index a094aa81ad225..6b57c658cf918 100644 --- a/arch/arm64/boot/dts/qcom/sm8250-lge-timelm.dts +++ b/arch/arm64/boot/dts/qcom/sm8250-lge-timelm.dts @@ -535,6 +535,24 @@ &sdhc_2 { no-mmc; }; +&pm8150b_typec { + status = "okay"; + + vdd-pdphy-supply = <&vreg_l2a_3p1>; + + connector { + compatible = "usb-c-connector"; + + power-role = "sink"; + data-role = "device"; + self-powered; + + op-sink-microwatt = <15000000>; + sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM) + PDO_BATT(5000, 9000, 15000)>; + }; +}; + &usb_1 { status = "okay"; }; -- 2.39.5 ^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v1 11/11] arm64: dts: qcom: sm8250-lge-timelm: add QCA6390 Bluetooth 2026-11-17 12:39 [PATCH v1 00/11] arm64: qcom: Add initial support for LG V60 ThinQ 5G (timelm) rofikkerneldev ` (9 preceding siblings ...) 2026-11-17 12:39 ` [PATCH v1 10/11] arm64: dts: qcom: sm8250-lge-timelm: enable USB Type-C rofikkerneldev @ 2026-11-17 12:39 ` rofikkerneldev 10 siblings, 0 replies; 12+ messages in thread From: rofikkerneldev @ 2026-11-17 12:39 UTC (permalink / raw) To: linux-arm-msm Cc: devicetree, dri-devel, linux-input, linux-kernel, Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Neil Armstrong, Dmitry Torokhov, rofikkerneldev Describe the QCA6390 power sequencer and its PMU regulators. Enable the Bluetooth HCI controller on GENI UART6 with the supplies provided by the PMU. Signed-off-by: rofikkerneldev <rofikcoga@gmail.com> --- .../arm64/boot/dts/qcom/sm8250-lge-timelm.dts | 92 +++++++++++++++++++ 1 file changed, 92 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sm8250-lge-timelm.dts b/arch/arm64/boot/dts/qcom/sm8250-lge-timelm.dts index 6b57c658cf918..38816268fcf53 100644 --- a/arch/arm64/boot/dts/qcom/sm8250-lge-timelm.dts +++ b/arch/arm64/boot/dts/qcom/sm8250-lge-timelm.dts @@ -95,6 +95,67 @@ key-assistant { }; }; + qca6390-pmu { + compatible = "qcom,qca6390-pmu"; + + pinctrl-names = "default"; + pinctrl-0 = <&bt_en_state>, <&wlan_en_state>; + + vddaon-supply = <&vreg_s6a_0p6>; + vddpmu-supply = <&vreg_s6a_0p6>; + vddrfa0p95-supply = <&vreg_s6a_0p6>; + vddrfa1p3-supply = <&vreg_s8c_1p2>; + vddrfa1p9-supply = <&vreg_s5a_1p9>; + vddpcie1p3-supply = <&vreg_s8c_1p2>; + vddpcie1p9-supply = <&vreg_s5a_1p9>; + vddio-supply = <&vreg_s4a_1p8>; + + wlan-enable-gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>; + bt-enable-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>; + + regulators { + vreg_pmu_rfa_cmn: ldo0 { + regulator-name = "vreg_pmu_rfa_cmn"; + }; + + vreg_pmu_aon_0p59: ldo1 { + regulator-name = "vreg_pmu_aon_0p59"; + }; + + vreg_pmu_wlcx_0p8: ldo2 { + regulator-name = "vreg_pmu_wlcx_0p8"; + }; + + vreg_pmu_wlmx_0p85: ldo3 { + regulator-name = "vreg_pmu_wlmx_0p85"; + }; + + vreg_pmu_btcmx_0p85: ldo4 { + regulator-name = "vreg_pmu_btcmx_0p85"; + }; + + vreg_pmu_rfa_0p8: ldo5 { + regulator-name = "vreg_pmu_rfa_0p8"; + }; + + vreg_pmu_rfa_1p2: ldo6 { + regulator-name = "vreg_pmu_rfa_1p2"; + }; + + vreg_pmu_rfa_1p7: ldo7 { + regulator-name = "vreg_pmu_rfa_1p7"; + }; + + vreg_pmu_pcie_0p9: ldo8 { + regulator-name = "vreg_pmu_pcie_0p9"; + }; + + vreg_pmu_pcie_1p8: ldo9 { + regulator-name = "vreg_pmu_pcie_1p8"; + }; + }; + }; + reserved-memory { ramoops: ramoops@b0000000 { compatible = "ramoops"; @@ -506,6 +567,21 @@ &uart12 { status = "okay"; }; +&uart6 { + status = "okay"; + + bluetooth { + compatible = "qcom,qca6390-bt"; + + vddrfacmn-supply = <&vreg_pmu_rfa_cmn>; + vddaon-supply = <&vreg_pmu_aon_0p59>; + vddbtcmx-supply = <&vreg_pmu_btcmx_0p85>; + vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>; + vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>; + vddrfa1p7-supply = <&vreg_pmu_rfa_1p7>; + }; +}; + &ufs_mem_hc { status = "okay"; @@ -636,6 +712,22 @@ touchscreen@28 { }; &tlmm { + bt_en_state: bt-enable-state { + pins = "gpio21"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + output-low; + }; + + wlan_en_state: wlan-enable-state { + pins = "gpio20"; + function = "gpio"; + drive-strength = <16>; + bias-pull-up; + output-low; + }; + touch_reset_default: touch-reset-default-state { pins = "gpio38"; function = "gpio"; -- 2.39.5 ^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2026-11-17 12:40 UTC | newest] Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2026-11-17 12:39 [PATCH v1 00/11] arm64: qcom: Add initial support for LG V60 ThinQ 5G (timelm) rofikkerneldev 2026-11-17 12:39 ` [PATCH v1 01/11] dt-bindings: arm: qcom: add " rofikkerneldev 2026-11-17 12:39 ` [PATCH v1 02/11] arm64: dts: qcom: add LG V60 ThinQ 5G (timelm) support rofikkerneldev 2026-11-17 12:39 ` [PATCH v1 03/11] arm64: dts: qcom: sm8250-lge-timelm: add reserved memory regions rofikkerneldev 2026-11-17 12:39 ` [PATCH v1 04/11] dt-bindings: display: panel: add LG SW43103 rofikkerneldev 2026-11-17 12:39 ` [PATCH v1 05/11] drm/panel: add LG SW43103 panel driver rofikkerneldev 2026-11-17 12:39 ` [PATCH v1 06/11] dt-bindings: input: touchscreen: add Silicon Works SW42902 rofikkerneldev 2026-11-17 12:39 ` [PATCH v1 07/11] Input: touchscreen: add Silicon Works SW42902 support rofikkerneldev 2026-11-17 12:39 ` [PATCH v1 08/11] arm64: dts: qcom: sm8250-lge-timelm: enable SW43103 panel rofikkerneldev 2026-11-17 12:39 ` [PATCH v1 09/11] arm64: dts: qcom: sm8250-lge-timelm: add SW42902 touchscreen rofikkerneldev 2026-11-17 12:39 ` [PATCH v1 10/11] arm64: dts: qcom: sm8250-lge-timelm: enable USB Type-C rofikkerneldev 2026-11-17 12:39 ` [PATCH v1 11/11] arm64: dts: qcom: sm8250-lge-timelm: add QCA6390 Bluetooth rofikkerneldev
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®