* [PATCH 0/5] Add bootph-all property for J7 boards
@ 2024-05-07 9:44 Manorit Chawdhry
2024-05-07 9:44 ` [PATCH 1/5] arm64: dts: ti: k3-j721s2*: Add bootph-* properties Manorit Chawdhry
` (4 more replies)
0 siblings, 5 replies; 7+ messages in thread
From: Manorit Chawdhry @ 2024-05-07 9:44 UTC (permalink / raw)
To: Nishanth Menon, Vignesh Raghavendra, Tero Kristo, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-arm-kernel, devicetree, linux-kernel, Neha Malcom Francis,
Aniket Limaye, Udit Kumar, Beleswar Padhi, Manorit Chawdhry
The idea of this series is to add bootph-all and bootph-pre-ram property
in all the leaf nodes wherever required and cleanup any other places where
bootph-all/bootph-pre-ram exist in the parent nodes as well.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
---
Manorit Chawdhry (5):
arm64: dts: ti: k3-j721s2*: Add bootph-* properties
arm64: dts: ti: k3-j784s4*: Remove bootph properties from parent nodes
arm64: dts: ti: k3-am68*: Add bootph-* properties
arm64: dts: ti: k3-j721e*: Add bootph-* properties
arm64: dts: ti: k3-j7200*: Add bootph-* properties
arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts | 10 ++++++++++
arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi | 3 +++
.../boot/dts/ti/k3-j7200-common-proc-board.dts | 23 ++++++++++++++++++++++
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 2 ++
arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 10 ++++++++++
arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 8 ++++++++
.../boot/dts/ti/k3-j721e-common-proc-board.dts | 20 +++++++++++++++++++
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 2 ++
arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi | 9 +++++++++
arch/arm64/boot/dts/ti/k3-j721e-sk.dts | 17 ++++++++++++++++
arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi | 5 +++++
.../boot/dts/ti/k3-j721s2-common-proc-board.dts | 14 +++++++++++++
arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 1 +
arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi | 10 ++++++++++
arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 2 ++
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 10 +---------
arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi | 1 +
arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi | 6 +++---
18 files changed, 141 insertions(+), 12 deletions(-)
---
base-commit: 11cb68ad52ac78c81e33b806b531f097e68edfa2
change-id: 20240430-b4-upstream-bootph-all-8d47b72bc0fd
Best regards,
--
Manorit Chawdhry <m-chawdhry@ti.com>
^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH 1/5] arm64: dts: ti: k3-j721s2*: Add bootph-* properties
2024-05-07 9:44 [PATCH 0/5] Add bootph-all property for J7 boards Manorit Chawdhry
@ 2024-05-07 9:44 ` Manorit Chawdhry
2024-05-07 9:44 ` [PATCH 2/5] arm64: dts: ti: k3-j784s4*: Remove bootph properties from parent nodes Manorit Chawdhry
` (3 subsequent siblings)
4 siblings, 0 replies; 7+ messages in thread
From: Manorit Chawdhry @ 2024-05-07 9:44 UTC (permalink / raw)
To: Nishanth Menon, Vignesh Raghavendra, Tero Kristo, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-arm-kernel, devicetree, linux-kernel, Neha Malcom Francis,
Aniket Limaye, Udit Kumar, Beleswar Padhi, Manorit Chawdhry
Adds bootph-* properties to the leaf nodes to enable U-boot to
utilise them.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
---
arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts | 14 ++++++++++++++
arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 1 +
arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi | 10 ++++++++++
arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 2 ++
4 files changed, 27 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
index c5a0b7cbb14f..6ce14f9e087b 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -138,6 +138,7 @@ J721S2_IOPAD(0x044, PIN_OUTPUT, 14) /* (Y26) MCASP0_AXR1.UART8_RTSn */
J721S2_IOPAD(0x0d0, PIN_INPUT, 11) /* (AF26) SPI0_CS1.UART8_RXD */
J721S2_IOPAD(0x0d4, PIN_OUTPUT, 11) /* (AH27) SPI0_CLK.UART8_TXD */
>;
+ bootph-all;
};
main_i2c3_pins_default: main-i2c3-default-pins {
@@ -165,6 +166,7 @@ J721S2_IOPAD(0x0f4, PIN_INPUT, 0) /* (R24) MMC1_DAT2 */
J721S2_IOPAD(0x0f0, PIN_INPUT, 0) /* (R22) MMC1_DAT3 */
J721S2_IOPAD(0x0e8, PIN_INPUT, 8) /* (AE25) TIMER_IO0.MMC1_SDCD */
>;
+ bootph-all;
};
vdd_sd_dv_pins_default: vdd-sd-dv-default-pins {
@@ -177,6 +179,7 @@ main_usbss0_pins_default: main-usbss0-default-pins {
pinctrl-single,pins = <
J721S2_IOPAD(0x0ec, PIN_OUTPUT, 6) /* (AG25) TIMER_IO1.USB0_DRVVBUS */
>;
+ bootph-all;
};
main_mcan3_pins_default: main-mcan3-default-pins {
@@ -200,6 +203,7 @@ wkup_uart0_pins_default: wkup-uart0-default-pins {
J721S2_WKUP_IOPAD(0x048, PIN_INPUT, 0) /* (D28) WKUP_UART0_RXD */
J721S2_WKUP_IOPAD(0x04c, PIN_OUTPUT, 0) /* (D27) WKUP_UART0_TXD */
>;
+ bootph-all;
};
mcu_uart0_pins_default: mcu-uart0-default-pins {
@@ -209,6 +213,7 @@ J721S2_WKUP_IOPAD(0x094, PIN_OUTPUT, 0) /* (D25) WKUP_GPIO0_15.MCU_UART0_RTSn */
J721S2_WKUP_IOPAD(0x08c, PIN_INPUT, 0) /* (C24) WKUP_GPIO0_13.MCU_UART0_RXD */
J721S2_WKUP_IOPAD(0x088, PIN_OUTPUT, 0) /* (C25) WKUP_GPIO0_12.MCU_UART0_TXD */
>;
+ bootph-all;
};
mcu_cpsw_pins_default: mcu-cpsw-default-pins {
@@ -301,6 +306,7 @@ J721S2_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (A20) MCU_OSPI1_D3 */
J721S2_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (B19) MCU_OSPI1_DQS */
J721S2_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (B20) MCU_OSPI1_LBCLKO */
>;
+ bootph-all;
};
};
@@ -316,12 +322,14 @@ &wkup_uart0 {
status = "reserved";
pinctrl-names = "default";
pinctrl-0 = <&wkup_uart0_pins_default>;
+ bootph-all;
};
&mcu_uart0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mcu_uart0_pins_default>;
+ bootph-all;
};
&main_uart8 {
@@ -330,6 +338,7 @@ &main_uart8 {
pinctrl-0 = <&main_uart8_pins_default>;
/* Shared with TFA on this platform */
power-domains = <&k3_pds 357 TI_SCI_PD_SHARED>;
+ bootph-all;
};
&main_i2c0 {
@@ -385,6 +394,7 @@ &main_sdhci0 {
non-removable;
ti,driver-strength-ohm = <50>;
disable-wp;
+ bootph-all;
};
&main_sdhci1 {
@@ -395,6 +405,7 @@ &main_sdhci1 {
disable-wp;
vmmc-supply = <&vdd_mmc1>;
vqmmc-supply = <&vdd_sd_dv>;
+ bootph-all;
};
&mcu_cpsw {
@@ -446,11 +457,13 @@ &usbss0 {
pinctrl-names = "default";
ti,vbus-divider;
ti,usb2-only;
+ bootph-all;
};
&usb0 {
dr_mode = "otg";
maximum-speed = "high-speed";
+ bootph-all;
};
&ospi1 {
@@ -469,6 +482,7 @@ flash@0 {
cdns,tchsh-ns = <60>;
cdns,tslch-ns = <60>;
cdns,read-delay = <2>;
+ bootph-all;
};
};
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
index b70c8615e3c1..fd1513f33616 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
@@ -828,6 +828,7 @@ secure_proxy_main: mailbox@32c00000 {
<0x00 0x32800000 0x00 0x100000>;
interrupt-names = "rx_011";
interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ bootph-all;
};
hwspinlock: spinlock@30e00000 {
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
index eaf7f709440e..b5013bba8509 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
@@ -21,16 +21,19 @@ sms: system-controller@44083000 {
k3_pds: power-controller {
compatible = "ti,sci-pm-domain";
#power-domain-cells = <2>;
+ bootph-all;
};
k3_clks: clock-controller {
compatible = "ti,k2g-sci-clk";
#clock-cells = <2>;
+ bootph-all;
};
k3_reset: reset-controller {
compatible = "ti,sci-reset";
#reset-cells = <2>;
+ bootph-all;
};
};
@@ -43,6 +46,7 @@ wkup_conf: bus@43000000 {
chipid: chipid@14 {
compatible = "ti,am654-chipid";
reg = <0x14 0x4>;
+ bootph-all;
};
};
@@ -59,6 +63,7 @@ secure_proxy_sa3: mailbox@43600000 {
* firmware on non-MPU processors
*/
status = "disabled";
+ bootph-pre-ram;
};
mcu_ram: sram@41c00000 {
@@ -166,6 +171,7 @@ mcu_timer0: timer@40400000 {
ti,timer-pwm;
/* Non-MPU Firmware usage */
status = "reserved";
+ bootph-pre-ram;
};
mcu_timer1: timer@40410000 {
@@ -360,6 +366,7 @@ wkup_i2c0: i2c@42120000 {
clock-names = "fck";
power-domains = <&k3_pds 223 TI_SCI_PD_EXCLUSIVE>;
status = "disabled";
+ bootph-all;
};
mcu_i2c0: i2c@40b00000 {
@@ -472,6 +479,7 @@ mcu_ringacc: ringacc@2b800000 {
ti,sci = <&sms>;
ti,sci-dev-id = <272>;
msi-parent = <&main_udmass_inta>;
+ bootph-all;
};
mcu_udmap: dma-controller@285c0000 {
@@ -495,6 +503,7 @@ mcu_udmap: dma-controller@285c0000 {
ti,sci-rm-range-rchan = <0x0a>, /* RX_CHAN */
<0x0b>; /* RX_HCHAN */
ti,sci-rm-range-rflow = <0x00>; /* GP RFLOW */
+ bootph-all;
};
};
@@ -511,6 +520,7 @@ secure_proxy_mcu: mailbox@2a480000 {
* firmware on non-MPU processors
*/
status = "disabled";
+ bootph-pre-ram;
};
mcu_cpsw: ethernet@46000000 {
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
index 623c8421525d..f3898cd49ed9 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
@@ -16,6 +16,7 @@ memory@80000000 {
/* 16 GB RAM */
reg = <0x00 0x80000000 0x00 0x80000000>,
<0x08 0x80000000 0x03 0x80000000>;
+ bootph-all;
};
/* Reserving memory regions still pending */
@@ -444,6 +445,7 @@ flash@0 {
cdns,tchsh-ns = <60>;
cdns,tslch-ns = <60>;
cdns,read-delay = <4>;
+ bootph-all;
};
};
--
2.43.2
^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH 2/5] arm64: dts: ti: k3-j784s4*: Remove bootph properties from parent nodes
2024-05-07 9:44 [PATCH 0/5] Add bootph-all property for J7 boards Manorit Chawdhry
2024-05-07 9:44 ` [PATCH 1/5] arm64: dts: ti: k3-j721s2*: Add bootph-* properties Manorit Chawdhry
@ 2024-05-07 9:44 ` Manorit Chawdhry
2024-05-07 9:44 ` [PATCH 3/5] arm64: dts: ti: k3-am68*: Add bootph-* properties Manorit Chawdhry
` (2 subsequent siblings)
4 siblings, 0 replies; 7+ messages in thread
From: Manorit Chawdhry @ 2024-05-07 9:44 UTC (permalink / raw)
To: Nishanth Menon, Vignesh Raghavendra, Tero Kristo, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-arm-kernel, devicetree, linux-kernel, Neha Malcom Francis,
Aniket Limaye, Udit Kumar, Beleswar Padhi, Manorit Chawdhry
Removes bootph-* properties from parent nodes and aligns the bootph-* to
other u-boot.dtsi
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
---
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 10 +---------
arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi | 1 +
arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi | 6 +++---
3 files changed, 5 insertions(+), 12 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
index 81fd7afac8c5..f262eb1a6c65 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
@@ -279,7 +279,6 @@ &wkup_gpio0 {
};
&main_pmx0 {
- bootph-all;
main_uart8_pins_default: main-uart8-default-pins {
bootph-all;
pinctrl-single,pins = <
@@ -339,7 +338,6 @@ J784S4_IOPAD(0x010, PIN_INPUT_PULLUP, 8) /* (AH33) MCAN13_RX.I2C4_SDA */
};
&wkup_pmx2 {
- bootph-all;
wkup_uart0_pins_default: wkup-uart0-default-pins {
bootph-all;
pinctrl-single,pins = <
@@ -429,7 +427,6 @@ J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 7)
};
&wkup_pmx0 {
- bootph-all;
mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
bootph-all;
pinctrl-single,pins = <
@@ -449,7 +446,6 @@ J784S4_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (C34) MCU_OSPI0_DQS */
};
&wkup_pmx1 {
- bootph-all;
mcu_fss0_ospi0_1_pins_default: mcu-fss0-ospi0-1-default-pins {
bootph-all;
pinctrl-single,pins = <
@@ -520,6 +516,7 @@ bucka12: buck12 {
regulator-max-microvolt = <1100000>;
regulator-boot-on;
regulator-always-on;
+ bootph-pre-ram;
};
bucka3: buck3 {
@@ -600,18 +597,15 @@ &ufs_wrapper {
};
&fss {
- bootph-all;
status = "okay";
};
&ospi0 {
- bootph-all;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mcu_fss0_ospi0_pins_default>, <&mcu_fss0_ospi0_1_pins_default>;
flash@0 {
- bootph-all;
compatible = "jedec,spi-nor";
reg = <0x0>;
spi-tx-bus-width = <8>;
@@ -668,13 +662,11 @@ partition@3fc0000 {
};
&ospi1 {
- bootph-all;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mcu_fss0_ospi1_pins_default>;
flash@0 {
- bootph-all;
compatible = "jedec,spi-nor";
reg = <0x0>;
spi-tx-bus-width = <1>;
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
index b67c37460a73..46bd3cd1b006 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
@@ -1120,6 +1120,7 @@ secure_proxy_main: mailbox@32c00000 {
<0x00 0x32800000 0x00 0x100000>;
interrupt-names = "rx_011";
interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ bootph-all;
};
hwspinlock: hwlock@30e00000 {
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
index 77a8d99139ec..951ff3ec3ea0 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
@@ -39,7 +39,6 @@ k3_reset: reset-controller {
};
wkup_conf: bus@43000000 {
- bootph-all;
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
@@ -171,10 +170,10 @@ mcu_timer0: timer@40400000 {
ti,timer-pwm;
/* Non-MPU Firmware usage */
status = "reserved";
+ bootph-all;
};
mcu_timer1: timer@40410000 {
- bootph-all;
compatible = "ti,am654-timer";
reg = <0x00 0x40410000 0x00 0x400>;
interrupts = <GIC_SPI 817 IRQ_TYPE_LEVEL_HIGH>;
@@ -456,7 +455,6 @@ mcu_spi2: spi@40320000 {
};
mcu_navss: bus@28380000 {
- bootph-all;
compatible = "simple-bus";
#address-cells = <2>;
#size-cells = <2>;
@@ -519,6 +517,7 @@ secure_proxy_mcu: mailbox@2a480000 {
* firmware on non-MPU processors
*/
status = "disabled";
+ bootph-pre-ram;
};
mcu_cpsw: ethernet@46000000 {
@@ -630,6 +629,7 @@ wkup_vtm0: temperature-sensor@42040000 {
<0x00 0x42050000 0x00 0x350>;
power-domains = <&k3_pds 243 TI_SCI_PD_SHARED>;
#thermal-sensor-cells = <1>;
+ bootph-pre-ram;
};
tscadc0: tscadc@40200000 {
--
2.43.2
^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH 3/5] arm64: dts: ti: k3-am68*: Add bootph-* properties
2024-05-07 9:44 [PATCH 0/5] Add bootph-all property for J7 boards Manorit Chawdhry
2024-05-07 9:44 ` [PATCH 1/5] arm64: dts: ti: k3-j721s2*: Add bootph-* properties Manorit Chawdhry
2024-05-07 9:44 ` [PATCH 2/5] arm64: dts: ti: k3-j784s4*: Remove bootph properties from parent nodes Manorit Chawdhry
@ 2024-05-07 9:44 ` Manorit Chawdhry
2024-05-07 9:44 ` [PATCH 4/5] arm64: dts: ti: k3-j721e*: " Manorit Chawdhry
2024-05-07 9:44 ` [PATCH 5/5] arm64: dts: ti: k3-j7200*: " Manorit Chawdhry
4 siblings, 0 replies; 7+ messages in thread
From: Manorit Chawdhry @ 2024-05-07 9:44 UTC (permalink / raw)
To: Nishanth Menon, Vignesh Raghavendra, Tero Kristo, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-arm-kernel, devicetree, linux-kernel, Neha Malcom Francis,
Aniket Limaye, Udit Kumar, Beleswar Padhi, Manorit Chawdhry
Adds bootph-* properties to the leaf nodes to enable U-boot to
utilise them.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
---
arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts | 10 ++++++++++
arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi | 3 +++
2 files changed, 13 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
index d743f023cdd9..df97884cd1c5 100644
--- a/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
@@ -184,6 +184,7 @@ main_uart8_pins_default: main-uart8-default-pins {
J721S2_IOPAD(0x0d0, PIN_INPUT, 11) /* (AF26) SPI0_CS1.UART8_RXD */
J721S2_IOPAD(0x0d4, PIN_OUTPUT, 11) /* (AH27) SPI0_CLK.UART8_TXD */
>;
+ bootph-all;
};
main_i2c0_pins_default: main-i2c0-default-pins {
@@ -210,6 +211,7 @@ J721S2_IOPAD(0x0f4, PIN_INPUT, 0) /* (R24) MMC1_DAT2 */
J721S2_IOPAD(0x0f0, PIN_INPUT, 0) /* (R22) MMC1_DAT3 */
J721S2_IOPAD(0x0e8, PIN_INPUT, 8) /* (AE25) TIMER_IO0.MMC1_SDCD */
>;
+ bootph-all;
};
vdd_sd_dv_pins_default: vdd-sd-dv-default-pins {
@@ -222,6 +224,7 @@ main_usbss0_pins_default: main-usbss0-default-pins {
pinctrl-single,pins = <
J721S2_IOPAD(0x0ec, PIN_OUTPUT, 6) /* (AG25) TIMER_IO1.USB0_DRVVBUS */
>;
+ bootph-all;
};
main_mcan6_pins_default: main-mcan6-default-pins {
@@ -312,6 +315,7 @@ J721S2_WKUP_IOPAD(0x074, PIN_OUTPUT, 0) /* (F28) WKUP_GPIO0_7.WKUP_UART0_RTSn */
J721S2_WKUP_IOPAD(0x048, PIN_INPUT, 0) /* (D28) WKUP_UART0_RXD */
J721S2_WKUP_IOPAD(0x04c, PIN_OUTPUT, 0) /* (D27) WKUP_UART0_TXD */
>;
+ bootph-all;
};
mcu_cpsw_pins_default: mcu-cpsw-default-pins {
@@ -412,12 +416,14 @@ &wkup_uart0 {
status = "reserved";
pinctrl-names = "default";
pinctrl-0 = <&wkup_uart0_pins_default>;
+ bootph-all;
};
&mcu_uart0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mcu_uart0_pins_default>;
+ bootph-all;
};
&main_uart8 {
@@ -426,6 +432,7 @@ &main_uart8 {
pinctrl-0 = <&main_uart8_pins_default>;
/* Shared with TFA on this platform */
power-domains = <&k3_pds 357 TI_SCI_PD_SHARED>;
+ bootph-all;
};
&main_i2c0 {
@@ -520,6 +527,7 @@ &main_sdhci1 {
disable-wp;
vmmc-supply = <&vdd_mmc1>;
vqmmc-supply = <&vdd_sd_dv>;
+ bootph-all;
};
&mcu_cpsw {
@@ -652,6 +660,7 @@ &usbss0 {
pinctrl-0 = <&main_usbss0_pins_default>;
pinctrl-names = "default";
ti,vbus-divider;
+ bootph-all;
};
&usb0 {
@@ -659,4 +668,5 @@ &usb0 {
maximum-speed = "super-speed";
phys = <&serdes0_usb_link>;
phy-names = "cdns3,usb3-phy";
+ bootph-all;
};
diff --git a/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi b/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi
index 0f4a5da0ebc4..85f02d8c645d 100644
--- a/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi
@@ -14,6 +14,7 @@ memory@80000000 {
/* 16 GB RAM */
reg = <0x00 0x80000000 0x00 0x80000000>,
<0x08 0x80000000 0x03 0x80000000>;
+ bootph-all;
};
reserved_memory: reserved-memory {
@@ -136,6 +137,7 @@ wkup_i2c0_pins_default: wkup-i2c0-default-pins {
J721S2_WKUP_IOPAD(0x098, PIN_INPUT, 0) /* (H24) WKUP_I2C0_SCL */
J721S2_WKUP_IOPAD(0x09c, PIN_INPUT, 0) /* (H27) WKUP_I2C0_SDA */
>;
+ bootph-all;
};
};
@@ -149,6 +151,7 @@ eeprom@51 {
/* AT24C512C-MAHM-T */
compatible = "atmel,24c512";
reg = <0x51>;
+ bootph-all;
};
};
--
2.43.2
^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH 4/5] arm64: dts: ti: k3-j721e*: Add bootph-* properties
2024-05-07 9:44 [PATCH 0/5] Add bootph-all property for J7 boards Manorit Chawdhry
` (2 preceding siblings ...)
2024-05-07 9:44 ` [PATCH 3/5] arm64: dts: ti: k3-am68*: Add bootph-* properties Manorit Chawdhry
@ 2024-05-07 9:44 ` Manorit Chawdhry
2024-05-07 9:44 ` [PATCH 5/5] arm64: dts: ti: k3-j7200*: " Manorit Chawdhry
4 siblings, 0 replies; 7+ messages in thread
From: Manorit Chawdhry @ 2024-05-07 9:44 UTC (permalink / raw)
To: Nishanth Menon, Vignesh Raghavendra, Tero Kristo, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-arm-kernel, devicetree, linux-kernel, Neha Malcom Francis,
Aniket Limaye, Udit Kumar, Beleswar Padhi, Manorit Chawdhry
Adds bootph-* properties to the leaf nodes to enable U-boot to
utilise them.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
---
.../arm64/boot/dts/ti/k3-j721e-common-proc-board.dts | 20 ++++++++++++++++++++
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 2 ++
arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi | 9 +++++++++
arch/arm64/boot/dts/ti/k3-j721e-sk.dts | 17 +++++++++++++++++
arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi | 5 +++++
5 files changed, 53 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
index 8230d53cd696..ebc9ab3b6790 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
@@ -193,6 +193,7 @@ J721E_IOPAD(0x1c0, PIN_OUTPUT, 1) /* (AA2) SPI0_CS0.UART0_RTSn */
J721E_IOPAD(0x1e8, PIN_INPUT, 0) /* (AB2) UART0_RXD */
J721E_IOPAD(0x1ec, PIN_OUTPUT, 0) /* (AB3) UART0_TXD */
>;
+ bootph-all;
};
main_uart1_pins_default: main-uart1-default-pins {
@@ -234,6 +235,7 @@ J721E_IOPAD(0x240, PIN_INPUT, 0) /* (R26) MMC1_DAT3 */
J721E_IOPAD(0x258, PIN_INPUT, 0) /* (P23) MMC1_SDCD */
J721E_IOPAD(0x25c, PIN_INPUT, 0) /* (R28) MMC1_SDWP */
>;
+ bootph-all;
};
vdd_sd_dv_alt_pins_default: vdd-sd-dv-alt-default-pins {
@@ -247,6 +249,7 @@ main_usbss0_pins_default: main-usbss0-default-pins {
J721E_IOPAD(0x290, PIN_OUTPUT, 0) /* (U6) USB0_DRVVBUS */
J721E_IOPAD(0x210, PIN_INPUT, 7) /* (W3) MCAN1_RX.GPIO1_3 */
>;
+ bootph-all;
};
main_usbss1_pins_default: main-usbss1-default-pins {
@@ -272,6 +275,7 @@ main_i2c0_pins_default: main-i2c0-default-pins {
J721E_IOPAD(0x220, PIN_INPUT_PULLUP, 0) /* (AC5) I2C0_SCL */
J721E_IOPAD(0x224, PIN_INPUT_PULLUP, 0) /* (AA5) I2C0_SDA */
>;
+ bootph-all;
};
main_i2c1_pins_default: main-i2c1-default-pins {
@@ -342,6 +346,7 @@ wkup_uart0_pins_default: wkup-uart0-default-pins {
J721E_WKUP_IOPAD(0xa0, PIN_INPUT, 0) /* (J29) WKUP_UART0_RXD */
J721E_WKUP_IOPAD(0xa4, PIN_OUTPUT, 0) /* (J28) WKUP_UART0_TXD */
>;
+ bootph-all;
};
mcu_uart0_pins_default: mcu-uart0-default-pins {
@@ -351,6 +356,7 @@ J721E_WKUP_IOPAD(0xec, PIN_OUTPUT, 0) /* (J27) WKUP_GPIO0_15.MCU_UART0_RTSn */
J721E_WKUP_IOPAD(0xe4, PIN_INPUT, 0) /* (H28) WKUP_GPIO0_13.MCU_UART0_RXD */
J721E_WKUP_IOPAD(0xe0, PIN_OUTPUT, 0) /* (G29) WKUP_GPIO0_12.MCU_UART0_TXD */
>;
+ bootph-all;
};
sw11_button_pins_default: sw11-button-default-pins {
@@ -370,6 +376,7 @@ J721E_WKUP_IOPAD(0x4c, PIN_INPUT, 0) /* (C23) MCU_OSPI1_D3 */
J721E_WKUP_IOPAD(0x3c, PIN_INPUT, 0) /* (B23) MCU_OSPI1_DQS */
J721E_WKUP_IOPAD(0x38, PIN_INPUT, 0) /* (A23) MCU_OSPI1_LBCLKO */
>;
+ bootph-all;
};
mcu_cpsw_pins_default: mcu-cpsw-default-pins {
@@ -427,6 +434,7 @@ wkup_gpio_pins_default: wkup-gpio-default-pins {
pinctrl-single,pins = <
J721E_WKUP_IOPAD(0xd0, PIN_INPUT, 7) /* (C14) WKUP_GPIO0_8 */
>;
+ bootph-all;
};
};
@@ -435,12 +443,14 @@ &wkup_uart0 {
status = "reserved";
pinctrl-names = "default";
pinctrl-0 = <&wkup_uart0_pins_default>;
+ bootph-all;
};
&mcu_uart0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mcu_uart0_pins_default>;
+ bootph-all;
};
&main_uart0 {
@@ -449,6 +459,7 @@ &main_uart0 {
pinctrl-0 = <&main_uart0_pins_default>;
/* Shared with ATF on this platform */
power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>;
+ bootph-all;
};
&main_uart1 {
@@ -473,6 +484,7 @@ &wkup_gpio0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&wkup_gpio_pins_default>;
+ bootph-all;
};
&main_gpio0 {
@@ -489,6 +501,7 @@ &main_sdhci0 {
non-removable;
ti,driver-strength-ohm = <50>;
disable-wp;
+ bootph-all;
};
&main_sdhci1 {
@@ -500,10 +513,12 @@ &main_sdhci1 {
pinctrl-0 = <&main_mmc1_pins_default>;
ti,driver-strength-ohm = <50>;
disable-wp;
+ bootph-all;
};
&usb_serdes_mux {
idle-states = <1>, <0>; /* USB0 to SERDES3, USB1 to SERDES1 */
+ bootph-all;
};
&serdes_ln_ctrl {
@@ -513,6 +528,7 @@ &serdes_ln_ctrl {
<J721E_SERDES3_LANE0_USB3_0_SWAP>, <J721E_SERDES3_LANE1_USB3_0>,
<J721E_SERDES4_LANE0_EDP_LANE0>, <J721E_SERDES4_LANE1_EDP_LANE1>,
<J721E_SERDES4_LANE2_EDP_LANE2>, <J721E_SERDES4_LANE3_EDP_LANE3>;
+ bootph-all;
};
&serdes_wiz3 {
@@ -534,6 +550,7 @@ &usbss0 {
pinctrl-names = "default";
pinctrl-0 = <&main_usbss0_pins_default>;
ti,vbus-divider;
+ bootph-all;
};
&usb0 {
@@ -541,6 +558,7 @@ &usb0 {
maximum-speed = "super-speed";
phys = <&serdes3_usb_link>;
phy-names = "cdns3,usb3-phy";
+ bootph-all;
};
&usbss1 {
@@ -569,6 +587,7 @@ flash@0 {
cdns,tchsh-ns = <60>;
cdns,tslch-ns = <60>;
cdns,read-delay = <2>;
+ bootph-all;
partitions {
compatible = "fixed-partitions";
@@ -650,6 +669,7 @@ exp2: gpio@22 {
reg = <0x22>;
gpio-controller;
#gpio-cells = <2>;
+ bootph-all;
p09-hog {
/* P11 - MCASP/TRACE_MUX_S0 */
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
index c7eafbc862f9..cb8cf307be44 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
@@ -226,6 +226,7 @@ secure_proxy_main: mailbox@32c00000 {
<0x00 0x32800000 0x00 0x100000>;
interrupt-names = "rx_011";
interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ bootph-all;
};
smmu0: iommu@36600000 {
@@ -2864,5 +2865,6 @@ main_esm: esm@700000 {
compatible = "ti,j721e-esm";
reg = <0x0 0x700000 0x0 0x1000>;
ti,esm-pins = <344>, <345>;
+ bootph-all;
};
};
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
index 4618b697fbc4..c9baf0460cba 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
@@ -21,16 +21,19 @@ dmsc: system-controller@44083000 {
k3_pds: power-controller {
compatible = "ti,sci-pm-domain";
#power-domain-cells = <2>;
+ bootph-all;
};
k3_clks: clock-controller {
compatible = "ti,k2g-sci-clk";
#clock-cells = <2>;
+ bootph-all;
};
k3_reset: reset-controller {
compatible = "ti,sci-reset";
#reset-cells = <2>;
+ bootph-all;
};
};
@@ -57,6 +60,7 @@ wkup_conf: bus@43000000 {
chipid: chipid@14 {
compatible = "ti,am654-chipid";
reg = <0x14 0x4>;
+ bootph-all;
};
};
@@ -111,6 +115,7 @@ mcu_timer0: timer@40400000 {
ti,timer-pwm;
/* Non-MPU Firmware usage */
status = "reserved";
+ bootph-pre-ram;
};
mcu_timer1: timer@40410000 {
@@ -469,6 +474,7 @@ mcu_ringacc: ringacc@2b800000 {
ti,sci = <&dmsc>;
ti,sci-dev-id = <235>;
msi-parent = <&main_udmass_inta>;
+ bootph-all;
};
mcu_udmap: dma-controller@285c0000 {
@@ -493,6 +499,7 @@ mcu_udmap: dma-controller@285c0000 {
ti,sci-rm-range-rchan = <0x0a>, /* RX_CHAN */
<0x0b>; /* RX_HCHAN */
ti,sci-rm-range-rflow = <0x00>; /* GP RFLOW */
+ bootph-all;
};
};
@@ -509,6 +516,7 @@ secure_proxy_mcu: mailbox@2a480000 {
* firmware on non-MPU processors
*/
status = "disabled";
+ bootph-pre-ram;
};
mcu_cpsw: ethernet@46000000 {
@@ -681,6 +689,7 @@ wkup_vtm0: temperature-sensor@42040000 {
<0x00 0x43000300 0x00 0x10>;
power-domains = <&k3_pds 154 TI_SCI_PD_EXCLUSIVE>;
#thermal-sensor-cells = <1>;
+ bootph-pre-ram;
};
mcu_esm: esm@40800000 {
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-sk.dts b/arch/arm64/boot/dts/ti/k3-j721e-sk.dts
index 0c4575ad8d7c..a497e94b5b96 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721e-sk.dts
@@ -34,6 +34,7 @@ memory@80000000 {
/* 4G RAM */
reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
<0x00000008 0x80000000 0x00000000 0x80000000>;
+ bootph-all;
};
reserved_memory: reserved-memory {
@@ -309,6 +310,7 @@ J721E_IOPAD(0x244, PIN_INPUT, 0) /* (R25) MMC1_DAT2 */
J721E_IOPAD(0x240, PIN_INPUT, 0) /* (R26) MMC1_DAT3 */
J721E_IOPAD(0x258, PIN_INPUT, 0) /* (P23) MMC1_SDCD */
>;
+ bootph-all;
};
main_uart0_pins_default: main-uart0-default-pins {
@@ -353,12 +355,14 @@ main_usbss0_pins_default: main-usbss0-default-pins {
J721E_IOPAD(0x290, PIN_OUTPUT, 0) /* (U6) USB0_DRVVBUS */
J721E_IOPAD(0x210, PIN_INPUT, 7) /* (W3) MCAN1_RX.GPIO1_3 */
>;
+ bootph-all;
};
main_usbss1_pins_default: main-usbss1-default-pins {
pinctrl-single,pins = <
J721E_IOPAD(0x214, PIN_OUTPUT, 4) /* (V4) MCAN1_TX.USB1_DRVVBUS */
>;
+ bootph-all;
};
main_csi_mux_sel_pins_default: main-csi-mux-sel-default-pins {
@@ -518,6 +522,7 @@ J721E_WKUP_IOPAD(0x24, PIN_INPUT, 0) /* (B22) MCU_OSPI0_D6 */
J721E_WKUP_IOPAD(0x28, PIN_INPUT, 0) /* (G21) MCU_OSPI0_D7 */
J721E_WKUP_IOPAD(0x8, PIN_INPUT, 0) /* (D21) MCU_OSPI0_DQS */
>;
+ bootph-all;
};
vdd_mmc1_en_pins_default: vdd-mmc1-en-default-pins {
@@ -553,6 +558,7 @@ wkup_i2c0_pins_default: wkup-i2c0-default-pins {
J721E_WKUP_IOPAD(0xf8, PIN_INPUT_PULLUP, 0) /* (J25) WKUP_I2C0_SCL */
J721E_WKUP_IOPAD(0xfc, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SDA */
>;
+ bootph-all;
};
/* Reset for M.2 M Key slot on PCIe1 */
@@ -568,6 +574,7 @@ &wkup_uart0 {
status = "reserved";
pinctrl-names = "default";
pinctrl-0 = <&wkup_uart0_pins_default>;
+ bootph-all;
};
&wkup_i2c0 {
@@ -732,6 +739,7 @@ &mcu_uart0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mcu_uart0_pins_default>;
+ bootph-all;
};
&main_uart0 {
@@ -740,6 +748,7 @@ &main_uart0 {
pinctrl-0 = <&main_uart0_pins_default>;
/* Shared with ATF on this platform */
power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>;
+ bootph-all;
};
&main_uart1 {
@@ -757,6 +766,7 @@ &main_sdhci1 {
pinctrl-0 = <&main_mmc1_pins_default>;
ti,driver-strength-ohm = <50>;
disable-wp;
+ bootph-all;
};
&ospi0 {
@@ -775,6 +785,7 @@ flash@0 {
cdns,tchsh-ns = <60>;
cdns,tslch-ns = <60>;
cdns,read-delay = <4>;
+ bootph-all;
partitions {
compatible = "fixed-partitions";
@@ -914,6 +925,7 @@ &wkup_gpio0 {
&usb_serdes_mux {
idle-states = <1>, <1>; /* USB0 to SERDES3, USB1 to SERDES2 */
+ bootph-all;
};
&serdes_ln_ctrl {
@@ -923,6 +935,7 @@ &serdes_ln_ctrl {
<J721E_SERDES3_LANE0_USB3_0_SWAP>, <J721E_SERDES3_LANE1_USB3_0>,
<J721E_SERDES4_LANE0_EDP_LANE0>, <J721E_SERDES4_LANE1_EDP_LANE1>,
<J721E_SERDES4_LANE2_EDP_LANE2>, <J721E_SERDES4_LANE3_EDP_LANE3>;
+ bootph-all;
};
&serdes_wiz3 {
@@ -962,6 +975,7 @@ &usbss0 {
pinctrl-names = "default";
pinctrl-0 = <&main_usbss0_pins_default>;
ti,vbus-divider;
+ bootph-all;
};
&usb0 {
@@ -969,6 +983,7 @@ &usb0 {
maximum-speed = "super-speed";
phys = <&serdes3_usb_link>;
phy-names = "cdns3,usb3-phy";
+ bootph-all;
};
&serdes2 {
@@ -985,6 +1000,7 @@ &usbss1 {
pinctrl-names = "default";
pinctrl-0 = <&main_usbss1_pins_default>;
ti,vbus-divider;
+ bootph-all;
};
&usb1 {
@@ -992,6 +1008,7 @@ &usb1 {
maximum-speed = "super-speed";
phys = <&serdes2_usb_link>;
phy-names = "cdns3,usb3-phy";
+ bootph-all;
};
&mcu_cpsw {
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
index 1fae6495db07..37de479f9be8 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
@@ -150,6 +150,7 @@ wkup_i2c0_pins_default: wkup-i2c0-default-pins {
J721E_WKUP_IOPAD(0xf8, PIN_INPUT_PULLUP, 0) /* (J25) WKUP_I2C0_SCL */
J721E_WKUP_IOPAD(0xfc, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SDA */
>;
+ bootph-all;
};
pmic_irq_pins_default: pmic-irq-default-pins {
@@ -172,6 +173,7 @@ J721E_WKUP_IOPAD(0x0024, PIN_INPUT, 0) /* MCU_OSPI0_D6 */
J721E_WKUP_IOPAD(0x0028, PIN_INPUT, 0) /* MCU_OSPI0_D7 */
J721E_WKUP_IOPAD(0x002c, PIN_OUTPUT, 0) /* MCU_OSPI0_CSn0 */
>;
+ bootph-all;
};
mcu_fss0_hpb0_pins_default: mcu-fss0-hpb0-default-pins {
@@ -191,6 +193,7 @@ J721E_WKUP_IOPAD(0x20, PIN_INPUT, 1) /* MCU_HYPERBUS0_DQ5 */
J721E_WKUP_IOPAD(0x24, PIN_INPUT, 1) /* MCU_HYPERBUS0_DQ6 */
J721E_WKUP_IOPAD(0x28, PIN_INPUT, 1) /* MCU_HYPERBUS0_DQ7 */
>;
+ bootph-all;
};
};
@@ -377,6 +380,7 @@ flash@0 {
cdns,tchsh-ns = <60>;
cdns,tslch-ns = <60>;
cdns,read-delay = <0>;
+ bootph-all;
partitions {
compatible = "fixed-partitions";
@@ -439,6 +443,7 @@ &hbmc {
flash@0,0 {
compatible = "cypress,hyperflash", "cfi-flash";
reg = <0x00 0x00 0x4000000>;
+ bootph-all;
partitions {
compatible = "fixed-partitions";
--
2.43.2
^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH 5/5] arm64: dts: ti: k3-j7200*: Add bootph-* properties
2024-05-07 9:44 [PATCH 0/5] Add bootph-all property for J7 boards Manorit Chawdhry
` (3 preceding siblings ...)
2024-05-07 9:44 ` [PATCH 4/5] arm64: dts: ti: k3-j721e*: " Manorit Chawdhry
@ 2024-05-07 9:44 ` Manorit Chawdhry
2024-05-28 9:05 ` Limaye, Aniket
4 siblings, 1 reply; 7+ messages in thread
From: Manorit Chawdhry @ 2024-05-07 9:44 UTC (permalink / raw)
To: Nishanth Menon, Vignesh Raghavendra, Tero Kristo, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-arm-kernel, devicetree, linux-kernel, Neha Malcom Francis,
Aniket Limaye, Udit Kumar, Beleswar Padhi, Manorit Chawdhry
Adds bootph-* properties to the leaf nodes to enable U-boot to
utilise them.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
---
.../boot/dts/ti/k3-j7200-common-proc-board.dts | 23 ++++++++++++++++++++++
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 2 ++
arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 10 ++++++++++
arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 8 ++++++++
4 files changed, 43 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index 6593c5da82c0..f7b96e8d6462 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -129,6 +129,7 @@ J721E_WKUP_IOPAD(0x94, PIN_OUTPUT, 0) /* (E21) MCU_UART0_RTSn */
J721E_WKUP_IOPAD(0x8c, PIN_INPUT, 0) /* (D20) MCU_UART0_RXD */
J721E_WKUP_IOPAD(0x88, PIN_OUTPUT, 0) /* (D19) MCU_UART0_TXD */
>;
+ bootph-all;
};
wkup_uart0_pins_default: wkup-uart0-default-pins {
@@ -136,6 +137,7 @@ wkup_uart0_pins_default: wkup-uart0-default-pins {
J721E_WKUP_IOPAD(0x48, PIN_INPUT, 0) /* (B14) WKUP_UART0_RXD */
J721E_WKUP_IOPAD(0x4c, PIN_OUTPUT, 0) /* (A14) WKUP_UART0_TXD */
>;
+ bootph-all;
};
mcu_cpsw_pins_default: mcu-cpsw-default-pins {
@@ -153,12 +155,14 @@ J721E_WKUP_IOPAD(0x002c, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
J721E_WKUP_IOPAD(0x0018, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */
J721E_WKUP_IOPAD(0x001c, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
>;
+ bootph-all;
};
wkup_gpio_pins_default: wkup-gpio-default-pins {
pinctrl-single,pins = <
J721E_WKUP_IOPAD(0x70, PIN_INPUT, 7) /* (C14) WKUP_GPIO0_6 */
>;
+ bootph-all;
};
mcu_mdio_pins_default: mcu-mdio1-default-pins {
@@ -204,6 +208,7 @@ J721E_IOPAD(0xb4, PIN_OUTPUT, 0) /* (T17) UART0_TXD */
J721E_IOPAD(0xc0, PIN_INPUT, 2) /* (W3) SPI0_CS0.UART0_CTSn */
J721E_IOPAD(0xc4, PIN_OUTPUT, 2) /* (U5) SPI0_CS1.UART0_RTSn */
>;
+ bootph-all;
};
main_uart1_pins_default: main-uart1-default-pins {
@@ -238,6 +243,7 @@ J721E_IOPAD(0xf0, PIN_INPUT, 0) /* (N20) MMC1_DAT2 */
J721E_IOPAD(0xec, PIN_INPUT, 0) /* (N19) MMC1_DAT3 */
J721E_IOPAD(0xe4, PIN_INPUT, 8) /* (V1) TIMER_IO0.MMC1_SDCD */
>;
+ bootph-all;
};
vdd_sd_dv_pins_default: vdd-sd-dv-default-pins {
@@ -259,6 +265,7 @@ main_usbss0_pins_default: main-usbss0-default-pins {
pinctrl-single,pins = <
J721E_IOPAD(0x04, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */
>;
+ bootph-all;
};
};
@@ -267,12 +274,14 @@ &wkup_uart0 {
status = "reserved";
pinctrl-names = "default";
pinctrl-0 = <&wkup_uart0_pins_default>;
+ bootph-all;
};
&mcu_uart0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mcu_uart0_pins_default>;
+ bootph-all;
};
&main_uart0 {
@@ -281,6 +290,7 @@ &main_uart0 {
power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>;
pinctrl-names = "default";
pinctrl-0 = <&main_uart0_pins_default>;
+ bootph-all;
};
&main_uart1 {
@@ -293,6 +303,7 @@ &main_uart1 {
&main_uart2 {
/* MAIN UART 2 is used by R5F firmware */
status = "reserved";
+ bootph-all; /* Doubtful if required or not */
};
&main_uart3 {
@@ -310,11 +321,13 @@ &wkup_gpio0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&wkup_gpio_pins_default>;
+ bootph-all;
};
&mcu_cpsw {
pinctrl-names = "default";
pinctrl-0 = <&mcu_cpsw_pins_default>, <&mcu_mdio_pins_default>;
+ bootph-all;
};
&davinci_mdio {
@@ -341,6 +354,7 @@ exp1: gpio@20 {
reg = <0x20>;
gpio-controller;
#gpio-cells = <2>;
+ bootph-all;
};
exp2: gpio@22 {
@@ -348,6 +362,7 @@ exp2: gpio@22 {
reg = <0x22>;
gpio-controller;
#gpio-cells = <2>;
+ bootph-all;
};
};
@@ -381,6 +396,7 @@ &main_sdhci0 {
non-removable;
ti,driver-strength-ohm = <50>;
disable-wp;
+ bootph-all;
};
&main_sdhci1 {
@@ -392,15 +408,18 @@ &main_sdhci1 {
vqmmc-supply = <&vdd_sd_dv>;
ti,driver-strength-ohm = <50>;
disable-wp;
+ bootph-all;
};
&serdes_ln_ctrl {
idle-states = <J7200_SERDES0_LANE0_PCIE1_LANE0>, <J7200_SERDES0_LANE1_PCIE1_LANE1>,
<J7200_SERDES0_LANE2_QSGMII_LANE1>, <J7200_SERDES0_LANE3_IP4_UNUSED>;
+ bootph-all;
};
&usb_serdes_mux {
idle-states = <1>; /* USB0 to SERDES lane 3 */
+ bootph-all;
};
&usbss0 {
@@ -408,11 +427,13 @@ &usbss0 {
pinctrl-0 = <&main_usbss0_pins_default>;
ti,vbus-divider;
ti,usb2-only;
+ bootph-all;
};
&usb0 {
dr_mode = "otg";
maximum-speed = "high-speed";
+ bootph-all;
};
&tscadc0 {
@@ -432,6 +453,7 @@ serdes0_pcie_link: phy@0 {
#phy-cells = <0>;
cdns,phy-type = <PHY_TYPE_PCIE>;
resets = <&serdes_wiz0 1>, <&serdes_wiz0 2>;
+ bootph-all;
};
serdes0_qsgmii_link: phy@1 {
@@ -440,6 +462,7 @@ serdes0_qsgmii_link: phy@1 {
#phy-cells = <0>;
cdns,phy-type = <PHY_TYPE_QSGMII>;
resets = <&serdes_wiz0 3>;
+ bootph-all;
};
};
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
index 657f9cc9f4ea..111eba71ed33 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
@@ -136,6 +136,7 @@ secure_proxy_main: mailbox@32c00000 {
<0x00 0x32800000 0x00 0x100000>;
interrupt-names = "rx_011";
interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ bootph-all;
};
hwspinlock: spinlock@30e00000 {
@@ -1538,5 +1539,6 @@ main_esm: esm@700000 {
compatible = "ti,j721e-esm";
reg = <0x0 0x700000 0x0 0x1000>;
ti,esm-pins = <656>, <657>;
+ bootph-all;
};
};
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
index 7cf21c99956e..1e346451ee35 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
@@ -21,16 +21,19 @@ dmsc: system-controller@44083000 {
k3_pds: power-controller {
compatible = "ti,sci-pm-domain";
#power-domain-cells = <2>;
+ bootph-all;
};
k3_clks: clock-controller {
compatible = "ti,k2g-sci-clk";
#clock-cells = <2>;
+ bootph-all;
};
k3_reset: reset-controller {
compatible = "ti,sci-reset";
#reset-cells = <2>;
+ bootph-all;
};
};
@@ -45,6 +48,7 @@ mcu_timer0: timer@40400000 {
assigned-clock-parents = <&k3_clks 35 2>;
power-domains = <&k3_pds 35 TI_SCI_PD_EXCLUSIVE>;
ti,timer-pwm;
+ bootph-pre-ram;
};
mcu_timer1: timer@40410000 {
@@ -187,6 +191,7 @@ wkup_conf: bus@43000000 {
chipid: chipid@14 {
compatible = "ti,am654-chipid";
reg = <0x14 0x4>;
+ bootph-all;
};
};
@@ -347,6 +352,7 @@ mcu_ringacc: ringacc@2b800000 {
ti,sci = <&dmsc>;
ti,sci-dev-id = <235>;
msi-parent = <&main_udmass_inta>;
+ bootph-all;
};
mcu_udmap: dma-controller@285c0000 {
@@ -371,6 +377,7 @@ mcu_udmap: dma-controller@285c0000 {
ti,sci-rm-range-rchan = <0x0a>, /* RX_CHAN */
<0x0b>; /* RX_HCHAN */
ti,sci-rm-range-rflow = <0x00>; /* GP RFLOW */
+ bootph-all;
};
};
@@ -387,6 +394,7 @@ secure_proxy_mcu: mailbox@2a480000 {
* firmware on non-MPU processors
*/
status = "disabled";
+ bootph-pre-ram;
};
mcu_cpsw: ethernet@46000000 {
@@ -530,6 +538,7 @@ hbmc_mux: mux-controller@47000004 {
reg = <0x00 0x47000004 0x00 0x4>;
#mux-control-cells = <1>;
mux-reg-masks = <0x0 0x2>; /* HBMC select */
+ bootph-all;
};
hbmc: hyperbus@47034000 {
@@ -648,6 +657,7 @@ wkup_vtm0: temperature-sensor@42040000 {
<0x00 0x42050000 0x00 0x350>;
power-domains = <&k3_pds 154 TI_SCI_PD_EXCLUSIVE>;
#thermal-sensor-cells = <1>;
+ bootph-all;
};
mcu_esm: esm@40800000 {
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
index 7e6a584ac6f0..a875a79e95c6 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
@@ -15,6 +15,7 @@ memory@80000000 {
/* 4G RAM */
reg = <0x00 0x80000000 0x00 0x80000000>,
<0x08 0x80000000 0x00 0x80000000>;
+ bootph-all;
};
reserved_memory: reserved-memory {
@@ -120,6 +121,7 @@ J721E_WKUP_IOPAD(0x20, PIN_INPUT, 1) /* (B8) MCU_OSPI0_D5.MCU_HYPERBUS0_DQ5 */
J721E_WKUP_IOPAD(0x24, PIN_INPUT, 1) /* (A8) MCU_OSPI0_D6.MCU_HYPERBUS0_DQ6 */
J721E_WKUP_IOPAD(0x28, PIN_INPUT, 1) /* (A7) MCU_OSPI0_D7.MCU_HYPERBUS0_DQ7 */
>;
+ bootph-all;
};
mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
@@ -136,6 +138,7 @@ J721E_WKUP_IOPAD(0x0024, PIN_INPUT, 0) /* MCU_OSPI0_D6 */
J721E_WKUP_IOPAD(0x0028, PIN_INPUT, 0) /* MCU_OSPI0_D7 */
J721E_WKUP_IOPAD(0x0008, PIN_INPUT, 0) /* MCU_OSPI0_DQS */
>;
+ bootph-all;
};
};
@@ -145,6 +148,7 @@ wkup_i2c0_pins_default: wkup-i2c0-default-pins {
J721E_WKUP_IOPAD(0x98, PIN_INPUT_PULLUP, 0) /* (F20) WKUP_I2C0_SCL */
J721E_WKUP_IOPAD(0x9c, PIN_INPUT_PULLUP, 0) /* (H21) WKUP_I2C0_SDA */
>;
+ bootph-all;
};
};
@@ -162,6 +166,7 @@ main_i2c0_pins_default: main-i2c0-default-pins {
J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
>;
+ bootph-all;
};
main_mcan0_pins_default: main-mcan0-default-pins {
@@ -185,6 +190,7 @@ &hbmc {
flash@0,0 {
compatible = "cypress,hyperflash", "cfi-flash";
reg = <0x00 0x00 0x4000000>;
+ bootph-all;
partitions {
compatible = "fixed-partitions";
@@ -329,6 +335,7 @@ bucka1: buck1 {
regulator-max-microvolt = <1800000>;
regulator-boot-on;
regulator-always-on;
+ bootph-all;
};
bucka2: buck2 {
@@ -463,6 +470,7 @@ flash@0 {
cdns,tchsh-ns = <60>;
cdns,tslch-ns = <60>;
cdns,read-delay = <4>;
+ bootph-all;
partitions {
compatible = "fixed-partitions";
--
2.43.2
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH 5/5] arm64: dts: ti: k3-j7200*: Add bootph-* properties
2024-05-07 9:44 ` [PATCH 5/5] arm64: dts: ti: k3-j7200*: " Manorit Chawdhry
@ 2024-05-28 9:05 ` Limaye, Aniket
0 siblings, 0 replies; 7+ messages in thread
From: Limaye, Aniket @ 2024-05-28 9:05 UTC (permalink / raw)
To: Manorit Chawdhry, Nishanth Menon, Vignesh Raghavendra,
Tero Kristo, Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: linux-arm-kernel, devicetree, linux-kernel, Neha Malcom Francis,
Udit Kumar, Beleswar Padhi
Hi Manorit,
Had some comments below:
(Re-sending coz I forgot to change to plain-text formatting and the
mailing-list rejected it)
On 5/7/2024 3:14 PM, Manorit Chawdhry wrote:
> Adds bootph-* properties to the leaf nodes to enable U-boot to
> utilise them.
>
> Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
> ---
> .../boot/dts/ti/k3-j7200-common-proc-board.dts | 23 ++++++++++++++++++++++
> arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 2 ++
> arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 10 ++++++++++
> arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 8 ++++++++
> 4 files changed, 43 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> index 6593c5da82c0..f7b96e8d6462 100644
> --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
[...]
>
> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
> index 657f9cc9f4ea..111eba71ed33 100644
> --- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
> @@ -136,6 +136,7 @@ secure_proxy_main: mailbox@32c00000 {
> <0x00 0x32800000 0x00 0x100000>;
> interrupt-names = "rx_011";
> interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
> + bootph-all;
> };
>
> hwspinlock: spinlock@30e00000 {
> @@ -1538,5 +1539,6 @@ main_esm: esm@700000 {
> compatible = "ti,j721e-esm";
> reg = <0x0 0x700000 0x0 0x1000>;
> ti,esm-pins = <656>, <657>;
> + bootph-all;
Should this be bootph-pre-ram?
> };
> };
> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
> index 7cf21c99956e..1e346451ee35 100644
> --- a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
> @@ -21,16 +21,19 @@ dmsc: system-controller@44083000 {
Do we need to add bootph-all property to the parent "dmsc" node too?
For some reason, for me, boot is failing without the bootph-all property
in the parent "dmsc" node here, even though it;s added to the child
nodes below
Failing logs with current patch (boot gets stuck) : [0]
If I ONLY add the bootph-all property to the dmsc node as well, the
device boots up just fine.
[0]: https://gist.github.com/aniket-l/a33a2e5d71432f6824310c8658929b40
> k3_pds: power-controller {
> compatible = "ti,sci-pm-domain";
> #power-domain-cells = <2>;
> + bootph-all;
> };
>
> k3_clks: clock-controller {
> compatible = "ti,k2g-sci-clk";
> #clock-cells = <2>;
> + bootph-all;
> };
>
> k3_reset: reset-controller {
> compatible = "ti,sci-reset";
> #reset-cells = <2>;
> + bootph-all;
> };
> };
>
> @@ -45,6 +48,7 @@ mcu_timer0: timer@40400000 {
> assigned-clock-parents = <&k3_clks 35 2>;
> power-domains = <&k3_pds 35 TI_SCI_PD_EXCLUSIVE>;
> ti,timer-pwm;
> + bootph-pre-ram;
> };
>
> mcu_timer1: timer@40410000 {
> @@ -187,6 +191,7 @@ wkup_conf: bus@43000000 {
> chipid: chipid@14 {
> compatible = "ti,am654-chipid";
> reg = <0x14 0x4>;
> + bootph-all;
> };
> };
>
> @@ -347,6 +352,7 @@ mcu_ringacc: ringacc@2b800000 {
> ti,sci = <&dmsc>;
> ti,sci-dev-id = <235>;
> msi-parent = <&main_udmass_inta>;
> + bootph-all;
> };
>
> mcu_udmap: dma-controller@285c0000 {
> @@ -371,6 +377,7 @@ mcu_udmap: dma-controller@285c0000 {
> ti,sci-rm-range-rchan = <0x0a>, /* RX_CHAN */
> <0x0b>; /* RX_HCHAN */
> ti,sci-rm-range-rflow = <0x00>; /* GP RFLOW */
> + bootph-all;
> };
> };
>
> @@ -387,6 +394,7 @@ secure_proxy_mcu: mailbox@2a480000 {
> * firmware on non-MPU processors
> */
> status = "disabled";
> + bootph-pre-ram;
> };
>
> mcu_cpsw: ethernet@46000000 {
> @@ -530,6 +538,7 @@ hbmc_mux: mux-controller@47000004 {
> reg = <0x00 0x47000004 0x00 0x4>;
> #mux-control-cells = <1>;
> mux-reg-masks = <0x0 0x2>; /* HBMC select */
> + bootph-all;
> };
>
> hbmc: hyperbus@47034000 {
> @@ -648,6 +657,7 @@ wkup_vtm0: temperature-sensor@42040000 {
> <0x00 0x42050000 0x00 0x350>;
> power-domains = <&k3_pds 154 TI_SCI_PD_EXCLUSIVE>;
> #thermal-sensor-cells = <1>;
> + bootph-all;
Should this be bootph-pre-ram?
> };
>
> mcu_esm: esm@40800000 {
> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
> index 7e6a584ac6f0..a875a79e95c6 100644
> --- a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
> @@ -15,6 +15,7 @@ memory@80000000 {
> /* 4G RAM */
> reg = <0x00 0x80000000 0x00 0x80000000>,
> <0x08 0x80000000 0x00 0x80000000>;
> + bootph-all;
Can you add the right indentation here?
> };
>
> reserved_memory: reserved-memory {
> @@ -120,6 +121,7 @@ J721E_WKUP_IOPAD(0x20, PIN_INPUT, 1) /* (B8) MCU_OSPI0_D5.MCU_HYPERBUS0_DQ5 */
> J721E_WKUP_IOPAD(0x24, PIN_INPUT, 1) /* (A8) MCU_OSPI0_D6.MCU_HYPERBUS0_DQ6 */
> J721E_WKUP_IOPAD(0x28, PIN_INPUT, 1) /* (A7) MCU_OSPI0_D7.MCU_HYPERBUS0_DQ7 */
> >;
> + bootph-all;
> };
>
> mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
> @@ -136,6 +138,7 @@ J721E_WKUP_IOPAD(0x0024, PIN_INPUT, 0) /* MCU_OSPI0_D6 */
> J721E_WKUP_IOPAD(0x0028, PIN_INPUT, 0) /* MCU_OSPI0_D7 */
> J721E_WKUP_IOPAD(0x0008, PIN_INPUT, 0) /* MCU_OSPI0_DQS */
> >;
> + bootph-all;
> };
> };
>
[...]
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2024-05-28 9:05 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2024-05-07 9:44 [PATCH 0/5] Add bootph-all property for J7 boards Manorit Chawdhry
2024-05-07 9:44 ` [PATCH 1/5] arm64: dts: ti: k3-j721s2*: Add bootph-* properties Manorit Chawdhry
2024-05-07 9:44 ` [PATCH 2/5] arm64: dts: ti: k3-j784s4*: Remove bootph properties from parent nodes Manorit Chawdhry
2024-05-07 9:44 ` [PATCH 3/5] arm64: dts: ti: k3-am68*: Add bootph-* properties Manorit Chawdhry
2024-05-07 9:44 ` [PATCH 4/5] arm64: dts: ti: k3-j721e*: " Manorit Chawdhry
2024-05-07 9:44 ` [PATCH 5/5] arm64: dts: ti: k3-j7200*: " Manorit Chawdhry
2024-05-28 9:05 ` Limaye, Aniket
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®