* [PATCH v7 0/2] phy: Add CIX Sky1 USB3 PHY support
@ 2026-11-11 3:09 Hongliang Yang
2026-11-11 3:09 ` [PATCH v7 1/2] dt-bindings: phy: Add CIX Sky1 USB3 PHY Hongliang Yang
2026-11-11 3:09 ` [PATCH v7 2/2] phy: cix: Add CIX Sky1 USB3 PHY driver Hongliang Yang
0 siblings, 2 replies; 4+ messages in thread
From: Hongliang Yang @ 2026-11-11 3:09 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Manivannan Sadhasivam, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Philipp Zabel, Gary Yang,
Fugang Duan
Cc: linux-phy, linux-arm-kernel, devicetree, linux-kernel,
cix-kernel-upstream, Hongliang Yang
This series adds support for the USB3 PHY integrated in the CIX Sky1
SoC: the device tree binding and the PHY driver. It is a PHY series
only; the arm64 device tree nodes belong to the SoC subsystem and will
be sent separately once the binding is accepted. The PHY and the
USBSSP controller series were split in v4 and are posted independently.
The PHY provides the SuperSpeed lanes for the two USB3 Type-A (USB4
and USB5) Cadence USBSSP controllers of the SoC. There is one PHY
block with two lanes: they share one register block, the same clocks
and resets, and one initialization sequence, so the binding describes
the block as a single provider with #phy-cells = <0> and both
controllers reference the same phandle. The driver reference counts
phy_init() and phy_exit() accordingly.
v5 described one child node per lane. v6 collapsed them into the parent
node, but nothing in the binding or in the changelog said where the
second lane went. The second lane did not go anywhere: it is the second
lane of the same block and has no registers, clocks or resets of its
own. The binding description and the commit message now say that.
Tested on Radxa Orion O6 (Sky1) together with the USBSSP controller
series: the PHY probes and USB 3.x devices enumerate at SuperSpeed. The
series applies on top of v7.4-rc1.
Changes in v7:
- Removed the arm64 dts from the series; it is a separate SoC patchset.
- Describe the two lanes as one PHY provider and say why, instead of
dropping the per-lane child nodes without an explanation.
- Renamed the register header to phy-cix-usb3.h: it holds the register
map of the USB3 PHY, and the usbdp name suggested a USB/DP combo PHY.
- Fixed the module description and the Kconfig help text.
Changes in v6:
- Dropped the per-port child nodes; the PHY node itself is the provider
with #phy-cells = <0> and the driver exports a single PHY instance
shared by both controllers.
- Selected REGMAP in the PHY Kconfig.
- Used dev_err_probe() for the reset, clock and regmap acquisition
failures in the probe path.
Hongliang Yang (2):
dt-bindings: phy: Add CIX Sky1 USB3 PHY
phy: cix: Add CIX Sky1 USB3 PHY driver
.../bindings/phy/cix,sky1-usb3-phy.yaml | 78 ++++
MAINTAINERS | 2 +
drivers/phy/Kconfig | 1 +
drivers/phy/Makefile | 1 +
drivers/phy/cix/Kconfig | 21 +
drivers/phy/cix/Makefile | 6 +
drivers/phy/cix/phy-cix-usb3.c | 404 ++++++++++++++++++
drivers/phy/cix/phy-cix-usb3.h | 289 +++++++++++++
8 files changed, 802 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/cix,sky1-usb3-phy.yaml
create mode 100644 drivers/phy/cix/Kconfig
create mode 100644 drivers/phy/cix/Makefile
create mode 100644 drivers/phy/cix/phy-cix-usb3.c
create mode 100644 drivers/phy/cix/phy-cix-usb3.h
--
2.54.0
^ permalink raw reply [flat|nested] 4+ messages in thread
* [PATCH v7 1/2] dt-bindings: phy: Add CIX Sky1 USB3 PHY
2026-11-11 3:09 [PATCH v7 0/2] phy: Add CIX Sky1 USB3 PHY support Hongliang Yang
@ 2026-11-11 3:09 ` Hongliang Yang
2026-11-11 7:53 ` Krzysztof Kozlowski
2026-11-11 3:09 ` [PATCH v7 2/2] phy: cix: Add CIX Sky1 USB3 PHY driver Hongliang Yang
1 sibling, 1 reply; 4+ messages in thread
From: Hongliang Yang @ 2026-11-11 3:09 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Manivannan Sadhasivam, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Philipp Zabel, Gary Yang,
Fugang Duan
Cc: linux-phy, linux-arm-kernel, devicetree, linux-kernel,
cix-kernel-upstream, Hongliang Yang
Add device tree binding for the CIX Sky1 USB3 PHY, the SuperSpeedPlus
PHY of the two USB3 Type-A ports of the SoC.
The two lanes are not separate devices: they live in one register
block, share the same clocks and resets, and are brought up by the
same initialization sequence. The node is therefore a single PHY
provider with #phy-cells = <0>, referenced by both controllers, and the
driver reference counts phy_init() and phy_exit() so that the block is
set up once for all of them.
Signed-off-by: Hongliang Yang <hongliang.yang@cixtech.com>
---
Changes in v7:
- Describe the PHY as one provider of both lanes and say why. v5 had
one child node per lane, v6 dropped them, and nothing in the binding
or the changelog said where the second lane went.
- Reword the description so that it describes the provider instead of
the register programming of the block.
Changes in v6:
- Drop the per-port child nodes. The parent node is the PHY provider
with #phy-cells = <0>, as the block drives both lanes and the ports
share the initialization sequence.
---
.../bindings/phy/cix,sky1-usb3-phy.yaml | 78 +++++++++++++++++++
MAINTAINERS | 1 +
2 files changed, 79 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/cix,sky1-usb3-phy.yaml
diff --git a/Documentation/devicetree/bindings/phy/cix,sky1-usb3-phy.yaml b/Documentation/devicetree/bindings/phy/cix,sky1-usb3-phy.yaml
new file mode 100644
index 000000000000..205140bf84e7
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/cix,sky1-usb3-phy.yaml
@@ -0,0 +1,78 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/cix,sky1-usb3-phy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: CIX Sky1 USB3 PHY
+
+maintainers:
+ - Hongliang Yang <hongliang.yang@cixtech.com>
+
+description: |
+ The CIX Sky1 USB3 PHY provides the SuperSpeed lanes of the USB3 Type-A
+ ports of the SoC.
+
+ Both lanes are programmed through one register block and share the
+ same clocks and resets, so the node is a single PHY provider with
+ #phy-cells = <0> that all consumers reference. The driver reference
+ counts phy_init() and phy_exit(), so the block is set up once for all
+ its consumers.
+
+properties:
+ compatible:
+ const: cix,sky1-usb3-phy
+
+ reg:
+ maxItems: 1
+
+ "#phy-cells":
+ const: 0
+
+ clocks:
+ items:
+ - description: APB register interface clock
+ - description: PHY reference clock
+
+ clock-names:
+ items:
+ - const: apb
+ - const: ref
+
+ resets:
+ items:
+ - description: PHY reset
+ - description: PHY APB preset
+
+ reset-names:
+ items:
+ - const: core
+ - const: apb
+
+required:
+ - compatible
+ - reg
+ - "#phy-cells"
+ - clocks
+ - clock-names
+ - resets
+ - reset-names
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/cix,sky1.h>
+ #include <dt-bindings/reset/cix,sky1-s5-system-control.h>
+
+ usb-phy@9210000 {
+ compatible = "cix,sky1-usb3-phy";
+ reg = <0x9210000 0x40000>;
+ #phy-cells = <0>;
+ clocks = <&scmi_clk CLK_TREE_USB3A_PHY3_GATE>,
+ <&scmi_clk CLK_TREE_USB3A_PHY_x2_REF>;
+ clock-names = "apb", "ref";
+ resets = <&s5_syscon SKY1_USBPHY_SS_RST_N>,
+ <&s5_syscon SKY1_USBPHY_SS_PST_N>;
+ reset-names = "core", "apb";
+ };
diff --git a/MAINTAINERS b/MAINTAINERS
index 93abbb315065..73783abe027e 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2903,6 +2903,7 @@ S: Maintained
T: git https://github.com/cixtech/linux-mainline.git
F: Documentation/devicetree/bindings/arm/cix.yaml
F: Documentation/devicetree/bindings/mailbox/cix,sky1-mbox.yaml
+F: Documentation/devicetree/bindings/phy/cix,sky1-usb3-phy.yaml
F: arch/arm64/boot/dts/cix/
F: drivers/mailbox/cix-mailbox.c
K: \bcix\b
--
2.54.0
^ permalink raw reply [flat|nested] 4+ messages in thread
* [PATCH v7 2/2] phy: cix: Add CIX Sky1 USB3 PHY driver
2026-11-11 3:09 [PATCH v7 0/2] phy: Add CIX Sky1 USB3 PHY support Hongliang Yang
2026-11-11 3:09 ` [PATCH v7 1/2] dt-bindings: phy: Add CIX Sky1 USB3 PHY Hongliang Yang
@ 2026-11-11 3:09 ` Hongliang Yang
1 sibling, 0 replies; 4+ messages in thread
From: Hongliang Yang @ 2026-11-11 3:09 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Manivannan Sadhasivam, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Philipp Zabel, Gary Yang,
Fugang Duan
Cc: linux-phy, linux-arm-kernel, devicetree, linux-kernel,
cix-kernel-upstream, Hongliang Yang
Add a driver for the Cadence SD0803 USB3 PHY integrated in the CIX
Sky1 SoC. The driver enables the APB and reference clocks, releases the
resets, programs the register sequence of the PHY, and exports a single
PHY instance for the two lanes of the block. phy_init() and phy_exit()
are reference counted, so the sequence is programmed once and the block
stays powered while any of its consumers is active.
Signed-off-by: Hongliang Yang <hongliang.yang@cixtech.com>
---
Changes in v7:
- Rename the register header to phy-cix-usb3.h: it is the register map
of the USB3 PHY, and the old usbdp name suggested a USB/DP combo PHY.
- Fix the module description and the Kconfig help text.
Changes in v6:
- Select REGMAP in the Kconfig.
- Use dev_err_probe() for the reset, clock and regmap acquisition
failures in the probe path.
- Assert the resets before registering the PHY provider, disable the
clocks in LIFO order, and fix the error unroll path so that clocks
which were never enabled are not disabled.
---
MAINTAINERS | 1 +
drivers/phy/Kconfig | 1 +
drivers/phy/Makefile | 1 +
drivers/phy/cix/Kconfig | 21 ++
drivers/phy/cix/Makefile | 6 +
drivers/phy/cix/phy-cix-usb3.c | 404 +++++++++++++++++++++++++++++++++
drivers/phy/cix/phy-cix-usb3.h | 289 +++++++++++++++++++++++
7 files changed, 723 insertions(+)
create mode 100644 drivers/phy/cix/Kconfig
create mode 100644 drivers/phy/cix/Makefile
create mode 100644 drivers/phy/cix/phy-cix-usb3.c
create mode 100644 drivers/phy/cix/phy-cix-usb3.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 73783abe027e..b857e529e5e2 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2906,6 +2906,7 @@ F: Documentation/devicetree/bindings/mailbox/cix,sky1-mbox.yaml
F: Documentation/devicetree/bindings/phy/cix,sky1-usb3-phy.yaml
F: arch/arm64/boot/dts/cix/
F: drivers/mailbox/cix-mailbox.c
+F: drivers/phy/cix/
K: \bcix\b
ARM/CLKDEV SUPPORT
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index 105fbe408aa2..876e5857634c 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -176,6 +176,7 @@ source "drivers/phy/axiado/Kconfig"
source "drivers/phy/broadcom/Kconfig"
source "drivers/phy/cadence/Kconfig"
source "drivers/phy/canaan/Kconfig"
+source "drivers/phy/cix/Kconfig"
source "drivers/phy/eswin/Kconfig"
source "drivers/phy/freescale/Kconfig"
source "drivers/phy/hisilicon/Kconfig"
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index c6dd02003bbe..5a31c5df1746 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -28,6 +28,7 @@ obj-$(CONFIG_GENERIC_PHY) += allwinner/ \
broadcom/ \
cadence/ \
canaan/ \
+ cix/ \
eswin/ \
freescale/ \
hisilicon/ \
diff --git a/drivers/phy/cix/Kconfig b/drivers/phy/cix/Kconfig
new file mode 100644
index 000000000000..24452144ff78
--- /dev/null
+++ b/drivers/phy/cix/Kconfig
@@ -0,0 +1,21 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# PHY drivers for CIX PHYs
+#
+
+if ARCH_CIX || COMPILE_TEST
+
+config PHY_CIX_USB3
+ tristate "CIX Sky1 USB3 Type-A PHY support"
+ depends on OF && HAS_IOMEM
+ select GENERIC_PHY
+ select REGMAP
+ help
+ Enable this to support the USB3 SuperSpeed PHY of the Type-A
+ ports on CIX Sky1 SoCs. The PHY provides the SuperSpeed lanes
+ used by the two Cadence USBSSP controllers (USB4 and USB5) of
+ the SoC, and is shared between them.
+
+ If unsure, say N.
+
+endif # ARCH_CIX || COMPILE_TEST
diff --git a/drivers/phy/cix/Makefile b/drivers/phy/cix/Makefile
new file mode 100644
index 000000000000..58ec925a4425
--- /dev/null
+++ b/drivers/phy/cix/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Makefile for the CIX PHY drivers.
+#
+
+obj-$(CONFIG_PHY_CIX_USB3) += phy-cix-usb3.o
diff --git a/drivers/phy/cix/phy-cix-usb3.c b/drivers/phy/cix/phy-cix-usb3.c
new file mode 100644
index 000000000000..c6376f787af0
--- /dev/null
+++ b/drivers/phy/cix/phy-cix-usb3.c
@@ -0,0 +1,404 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * phy driver for cdn_sd0803_t7g_typea
+ *
+ * Author: Hongliang Yang <hongliang.yang@cixtech.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/property.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include "phy-cix-usb3.h"
+
+struct cix_u3phy;
+
+struct cix_u3phy_cfg {
+ int (*u3phy_init)(struct cix_u3phy *u3phy);
+ int (*u3phy_exit)(struct cix_u3phy *u3phy);
+};
+
+/*
+ * Cadence SD0803 Type-A USB3 PHY initialization sequence for the CIX
+ * Sky1 SoC, taken from the vendor-provided PHY register programming
+ * sequence for this SoC.
+ */
+static const struct reg_sequence sky1_u3phy_conf[] = {
+ {CMN_SSM_BIAS_TMR, 0x0018},
+ {CMN_PLLSM0_PLLPRE_TMR, 0x0030},
+ {CMN_PLLSM0_PLLLOCK_TMR, 0x00f0},
+ {CMN_PLLSM1_PLLPRE_TMR, 0x0030},
+ {CMN_PLLSM1_PLLLOCK_TMR, 0x00f0},
+ {CMN_BGCAL_INIT_TMR, 0x0078},
+ {CMN_BGCAL_ITER_TMR, 0x0078},
+ {CMN_IBCAL_INIT_TMR, 0x0018},
+ {CMN_TXPUCAL_INIT_TMR, 0x001d},
+ {CMN_TXPDCAL_INIT_TMR, 0x001d},
+ {CMN_RXCAL_INIT_TMR, 0x02d0},
+ {CMN_SD_CAL_PLLCNT_START, 0x0137},
+ {RX_SDCAL0_INIT_TMR_LANE0, 0x0018},
+ {RX_SDCAL0_INIT_TMR_LANE1, 0x0018},
+ {RX_SDCAL0_ITER_TMR_LANE0, 0x0078},
+ {RX_SDCAL0_ITER_TMR_LANE1, 0x0078},
+ {RX_SDCAL1_INIT_TMR_LANE0, 0x0018},
+ {RX_SDCAL1_INIT_TMR_LANE1, 0x0018},
+ {RX_SDCAL1_ITER_TMR_LANE0, 0x0078},
+ {RX_SDCAL1_ITER_TMR_LANE1, 0x0078},
+ {TX_RCVDET_ST_TMR_LANE0, 0x0960},
+ {TX_RCVDET_ST_TMR_LANE1, 0x0960},
+
+ {PHY_PLL_CFG_0803, 0x0000},
+ {CMN_PDIAG_PLL0_CLK_SEL_M0, 0x8600},
+ {XCVR_DIAG_HSCLK_SEL_LANE0, 0x0000},
+ {XCVR_DIAG_HSCLK_SEL_LANE1, 0x0000},
+ {XCVR_DIAG_HSCLK_DIV_LANE0, 0x0001},
+ {XCVR_DIAG_HSCLK_DIV_LANE1, 0x0001},
+ {XCVR_DIAG_PLLDRC_CTRL_LANE0, 0x0041},
+ {XCVR_DIAG_PLLDRC_CTRL_LANE1, 0x0041},
+ {CMN_PLL0_DSM_DIAG_M0, 0x0004},
+ {CMN_PLL1_DSM_DIAG_M0, 0x0004},
+ {CMN_PDIAG_PLL1_ITRIM_M0, 0x003f},
+ {CMN_PDIAG_PLL0_CP_PADJ_M0, 0x0b17},
+ {CMN_PDIAG_PLL1_CP_PADJ_M0, 0x0b17},
+ {CMN_PDIAG_PLL0_CP_IADJ_M0, 0x0e01},
+ {CMN_PDIAG_PLL1_CP_IADJ_M0, 0x0e01},
+ {CMN_PDIAG_PLL0_FILT_PADJ_M0, 0x0d05},
+ {CMN_PDIAG_PLL1_FILT_PADJ_M0, 0x0d05},
+ {CMN_PLL0_INTDIV_M0, 0x01a0},
+ {CMN_PLL1_INTDIV_M0, 0x01a0},
+ {CMN_PLL0_FRACDIVL_M0, 0xaaab},
+ {CMN_PLL1_FRACDIVL_M0, 0xaaab},
+ {CMN_PLL0_FRACDIVH_M0, 0x0002},
+ {CMN_PLL1_FRACDIVH_M0, 0x0002},
+ {CMN_PLL0_HIGH_THR_M0, 0x0116},
+ {CMN_PLL1_HIGH_THR_M0, 0x0116},
+ {CMN_PDIAG_PLL0_CTRL_M0, 0x1002},
+ {CMN_PDIAG_PLL1_CTRL_M0, 0x1002},
+ {CMN_PLL0_SS_CTRL1_M0, 0x0001}, /* SSC enabled */
+ {CMN_PLL0_VCOCAL_INIT_TMR, 0x00f0},
+ {CMN_PLL1_VCOCAL_INIT_TMR, 0x00f0},
+ {CMN_PLL0_VCOCAL_ITER_TMR, 0x0004},
+ {CMN_PLL1_VCOCAL_ITER_TMR, 0x0004},
+ {CMN_PLL0_VCOCAL_REFTIM_START, 0x02f8},
+ {CMN_PLL1_VCOCAL_REFTIM_START, 0x02f8},
+ {CMN_PLL0_VCOCAL_PLLCNT_START, 0x02f8},
+ {CMN_PLL1_VCOCAL_PLLCNT_START, 0x02f8},
+ {CMN_PLL0_VCOCAL_TCTRL, 0x0003},
+ {CMN_PLL1_VCOCAL_TCTRL, 0x0003},
+ {CMN_PLL0_LOCK_REFCNT_START, 0x00bf},
+ {CMN_PLL1_LOCK_REFCNT_START, 0x00bf},
+ {CMN_PLL0_LOCK_PLLCNT_START, 0x00bf},
+ {CMN_PLL1_LOCK_PLLCNT_START, 0x00bf},
+ {CMN_PLL0_LOCK_PLLCNT_THR, 0x0003},
+ {CMN_PLL1_LOCK_PLLCNT_THR, 0x0003},
+ {PHY_PIPE_USB3_GEN2_PRE_CFG0_0803, 0x0a0a},
+ {PHY_PIPE_USB3_GEN2_POST_CFG0_0803, 0x1000},
+ {PHY_PIPE_USB3_GEN2_POST_CFG1_0803, 0x0010},
+ {CMN_CDIAG_CDB_PWRI_OVRD, 0x8200},
+ {CMN_CDIAG_XCVRC_PWRI_OVRD, 0x8200},
+ {TX_PSC_A0_LANE0, 0x02ff},
+ {TX_PSC_A0_LANE1, 0x02ff},
+ {TX_PSC_A1_LANE0, 0x06af},
+ {TX_PSC_A1_LANE1, 0x06af},
+ {TX_PSC_A2_LANE0, 0x06ae},
+ {TX_PSC_A2_LANE1, 0x06ae},
+ {TX_PSC_A3_LANE0, 0x06ae},
+ {TX_PSC_A3_LANE1, 0x06ae},
+ {RX_PSC_A0_LANE0, 0x0d1d},
+ {RX_PSC_A0_LANE1, 0x0d1d},
+ {RX_PSC_A1_LANE0, 0x0d1d},
+ {RX_PSC_A1_LANE1, 0x0d1d},
+ {RX_PSC_A2_LANE0, 0x0d00},
+ {RX_PSC_A2_LANE1, 0x0d00},
+ {RX_PSC_A3_LANE0, 0x0500},
+ {RX_PSC_A3_LANE1, 0x0500},
+ {TX_TXCC_CTRL_LANE0, 0x2a82},
+ {TX_TXCC_CTRL_LANE1, 0x2a82},
+ {TX_TXCC_CPOST_MULT_01_LANE0, 0x0014},
+ {TX_TXCC_CPOST_MULT_01_LANE1, 0x0014},
+ {TX_TXCC_MGNFS_MULT_000_LANE0, 0x0002},
+ {TX_TXCC_MGNFS_MULT_000_LANE1, 0x0002},
+ {RX_SIGDET_HL_FILT_TMR_LANE0, 0x0013},
+ {RX_SIGDET_HL_FILT_TMR_LANE1, 0x0013},
+ {RX_REE_GCSM1_CTRL_LANE0, 0x0000},
+ {RX_REE_GCSM1_CTRL_LANE1, 0x0000},
+ {RX_REE_ATTEN_THR_LANE0, 0x0c02},
+ {RX_REE_ATTEN_THR_LANE1, 0x0c02},
+ {RX_REE_SMGM_CTRL1_LANE0, 0x0330},
+ {RX_REE_SMGM_CTRL1_LANE1, 0x0330},
+ {RX_REE_SMGM_CTRL2_LANE0, 0x0300},
+ {RX_REE_SMGM_CTRL2_LANE1, 0x0300},
+ {XCVR_DIAG_PSC_OVRD_LANE0, 0x0003},
+ {XCVR_DIAG_PSC_OVRD_LANE1, 0x0003},
+ {RX_DIAG_SIGDET_TUNE_LANE0, 0x1004},
+ {RX_DIAG_SIGDET_TUNE_LANE1, 0x1004},
+ {RX_DIAG_NQST_CTRL_LANE0, 0x00f9},
+ {RX_DIAG_NQST_CTRL_LANE1, 0x00f9},
+ {RX_DIAG_DFE_AMP_TUNE_2_LANE0, 0x0c01},
+ {RX_DIAG_DFE_AMP_TUNE_2_LANE1, 0x0c01},
+ {RX_DIAG_DFE_AMP_TUNE_3_LANE0, 0x0002},
+ {RX_DIAG_DFE_AMP_TUNE_3_LANE1, 0x0002},
+ {RX_DIAG_PI_CAP_LANE0, 0x0000},
+ {RX_DIAG_PI_CAP_LANE1, 0x0000},
+ {RX_DIAG_PI_RATE_LANE0, 0x0031},
+ {RX_DIAG_PI_RATE_LANE1, 0x0031},
+ {RX_CDRLF_CNFG_LANE0, 0x018c},
+ {RX_CDRLF_CNFG_LANE1, 0x018c},
+ {RX_CDRLF_CNFG3_LANE0, 0x0003},
+ {RX_CDRLF_CNFG3_LANE1, 0x0003}
+};
+
+struct cix_u3phy {
+ struct device *dev;
+ void __iomem *base;
+ struct regmap *phy_regmap;
+ struct reset_control *preset;
+ struct reset_control *reset;
+ struct clk *apb_clk;
+ struct clk *ref_clk;
+ struct mutex mutex; /* mutex to protect access to individual PHYs */
+ bool init;
+ int init_count;
+ const struct cix_u3phy_cfg *cfg;
+};
+
+static int sky1_u3phy_exit(struct cix_u3phy *u3phy)
+{
+ if (WARN_ON(!u3phy->init_count))
+ return -EINVAL;
+
+ u3phy->init_count--;
+ if (u3phy->init && u3phy->init_count == 0) {
+ reset_control_assert(u3phy->reset);
+ reset_control_assert(u3phy->preset);
+ clk_disable_unprepare(u3phy->ref_clk);
+ clk_disable_unprepare(u3phy->apb_clk);
+ u3phy->init = false;
+ }
+ return 0;
+}
+
+static int sky1_u3phy_init(struct cix_u3phy *u3phy)
+{
+ int ret;
+
+ if (!u3phy->init) {
+ /* usb rcsu reset is default deassert */
+ reset_control_assert(u3phy->reset);
+ reset_control_assert(u3phy->preset);
+ ret = clk_prepare_enable(u3phy->apb_clk);
+ if (ret) {
+ dev_err(u3phy->dev, "Failed to prepare_enable u3phy apb clock\n");
+ return ret;
+ }
+ ret = clk_prepare_enable(u3phy->ref_clk);
+ if (ret) {
+ dev_err(u3phy->dev, "Failed to prepare_enable u3phy ref clock\n");
+ goto disable_apb_clk;
+ }
+ reset_control_deassert(u3phy->preset);
+ ret = regmap_multi_reg_write(u3phy->phy_regmap, sky1_u3phy_conf,
+ ARRAY_SIZE(sky1_u3phy_conf));
+ if (ret) {
+ dev_err(u3phy->dev, "Failed to write the reg sequence\n");
+ goto assert_reset_preset;
+ }
+ u3phy->init = true;
+ reset_control_deassert(u3phy->reset);
+ }
+ u3phy->init_count++;
+ return 0;
+
+assert_reset_preset:
+ reset_control_assert(u3phy->preset);
+ reset_control_assert(u3phy->reset);
+ clk_disable_unprepare(u3phy->ref_clk);
+disable_apb_clk:
+ clk_disable_unprepare(u3phy->apb_clk);
+ return ret;
+}
+
+static const struct cix_u3phy_cfg sky1_u3phy_cfg = {
+ .u3phy_init = sky1_u3phy_init,
+ .u3phy_exit = sky1_u3phy_exit
+};
+
+static int u3phy_regmap_write(void *context, unsigned int reg, unsigned int val)
+{
+ struct cix_u3phy *u3phy = context;
+ u32 offset = reg << 2;
+
+ writel(val, u3phy->base + offset);
+ return 0;
+}
+
+static int u3phy_regmap_read(void *context, unsigned int reg, unsigned int *val)
+{
+ struct cix_u3phy *u3phy = context;
+ u32 offset = reg << 2;
+
+ *val = readl(u3phy->base + offset);
+ return 0;
+}
+
+static const struct regmap_config cix_u3phy_regmap_cfg = {
+ .reg_bits = 32,
+ .reg_stride = 1,
+ .val_bits = 16,
+ .fast_io = true,
+ .reg_write = u3phy_regmap_write,
+ .reg_read = u3phy_regmap_read,
+};
+
+static int cix_usb3_phy_power_on(struct cix_u3phy *u3phy)
+{
+ int ret;
+ const struct cix_u3phy_cfg *phy_cfgs = u3phy->cfg;
+
+ if (phy_cfgs->u3phy_init) {
+ ret = phy_cfgs->u3phy_init(u3phy);
+ if (ret) {
+ dev_err(u3phy->dev, "failed to init udphy\n");
+ return ret;
+ }
+ }
+ return 0;
+}
+
+static int cix_usb3_phy_power_off(struct cix_u3phy *u3phy)
+{
+ int ret;
+ const struct cix_u3phy_cfg *phy_cfgs = u3phy->cfg;
+
+ if (phy_cfgs->u3phy_exit) {
+ ret = phy_cfgs->u3phy_exit(u3phy);
+ if (ret) {
+ dev_err(u3phy->dev, "failed to exit udphy\n");
+ return ret;
+ }
+ }
+ return 0;
+}
+
+static int cix_u3phy_init(struct phy *phy)
+{
+ struct cix_u3phy *u3phy = phy_get_drvdata(phy);
+ int ret = 0;
+
+ mutex_lock(&u3phy->mutex);
+ ret = cix_usb3_phy_power_on(u3phy);
+ mutex_unlock(&u3phy->mutex);
+ return ret;
+}
+
+static int cix_u3phy_exit(struct phy *phy)
+{
+ struct cix_u3phy *u3phy = phy_get_drvdata(phy);
+ int ret = 0;
+
+ mutex_lock(&u3phy->mutex);
+ ret = cix_usb3_phy_power_off(u3phy);
+ mutex_unlock(&u3phy->mutex);
+ return ret;
+}
+
+static const struct phy_ops cix_u3phy_ops = {
+ .init = cix_u3phy_init,
+ .exit = cix_u3phy_exit,
+ .owner = THIS_MODULE,
+};
+
+static int cix_u3phy_probe(struct platform_device *pdev)
+{
+ struct cix_u3phy *u3phy;
+ struct device *dev = &pdev->dev;
+ struct phy_provider *phy_provider;
+ struct device_node *np = dev->of_node;
+ struct phy *phy;
+ int ret;
+
+ u3phy = devm_kzalloc(dev, sizeof(*u3phy), GFP_KERNEL);
+ if (!u3phy)
+ return -ENOMEM;
+ u3phy->dev = dev;
+ u3phy->cfg = device_get_match_data(dev);
+ if (!u3phy->cfg) {
+ dev_err(dev, "no OF data can be matched with %pOF node\n", np);
+ return -ENODEV;
+ }
+ u3phy->reset = devm_reset_control_get_exclusive(dev, "core");
+ if (IS_ERR(u3phy->reset))
+ return dev_err_probe(dev, PTR_ERR(u3phy->reset),
+ "failed to get core reset\n");
+ u3phy->preset = devm_reset_control_get_exclusive(dev, "apb");
+ if (IS_ERR(u3phy->preset))
+ return dev_err_probe(dev, PTR_ERR(u3phy->preset),
+ "failed to get APB reset\n");
+ u3phy->apb_clk = devm_clk_get(dev, "apb");
+ if (IS_ERR(u3phy->apb_clk))
+ return dev_err_probe(dev, PTR_ERR(u3phy->apb_clk),
+ "failed to get APB clock\n");
+ u3phy->ref_clk = devm_clk_get(dev, "ref");
+ if (IS_ERR(u3phy->ref_clk))
+ return dev_err_probe(dev, PTR_ERR(u3phy->ref_clk),
+ "failed to get reference clock\n");
+ u3phy->base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(u3phy->base))
+ return PTR_ERR(u3phy->base);
+ u3phy->phy_regmap = devm_regmap_init(dev, NULL, u3phy, &cix_u3phy_regmap_cfg);
+ if (IS_ERR(u3phy->phy_regmap))
+ return dev_err_probe(dev, PTR_ERR(u3phy->phy_regmap),
+ "failed to init PHY regmap\n");
+ ret = devm_mutex_init(dev, &u3phy->mutex);
+ if (ret)
+ return ret;
+ /*
+ * The PHY block drives both USB3 lanes and both controllers share
+ * the same initialization sequence, so a single PHY instance is
+ * exported and its init/exit calls are reference counted.
+ */
+ phy = devm_phy_create(dev, NULL, &cix_u3phy_ops);
+ if (IS_ERR(phy))
+ return dev_err_probe(dev, PTR_ERR(phy), "failed to create phy\n");
+ phy_set_drvdata(phy, u3phy);
+
+ /* keep the PHY in reset until a consumer calls phy_init() */
+ reset_control_assert(u3phy->reset);
+ reset_control_assert(u3phy->preset);
+
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+ if (IS_ERR(phy_provider))
+ return dev_err_probe(dev, PTR_ERR(phy_provider),
+ "failed to register phy provider\n");
+ return 0;
+}
+
+static const struct of_device_id cix_u3phy_dt_match[] = {
+ {
+ .compatible = "cix,sky1-usb3-phy",
+ .data = &sky1_u3phy_cfg
+ },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, cix_u3phy_dt_match);
+
+static struct platform_driver cix_usb3_phy_driver = {
+ .probe = cix_u3phy_probe,
+ .driver = {
+ .name = "cix-usb3-phy",
+ .of_match_table = cix_u3phy_dt_match,
+ },
+};
+
+module_platform_driver(cix_usb3_phy_driver);
+
+MODULE_AUTHOR("Hongliang Yang <hongliang.yang@cixtech.com>");
+MODULE_DESCRIPTION("CIX Sky1 USB3 PHY driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/phy/cix/phy-cix-usb3.h b/drivers/phy/cix/phy-cix-usb3.h
new file mode 100644
index 000000000000..22666cd3b253
--- /dev/null
+++ b/drivers/phy/cix/phy-cix-usb3.h
@@ -0,0 +1,289 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifndef _PHY_CIX_USB3_H
+#define _PHY_CIX_USB3_H
+
+#define CMN_SSM_BIAS_TMR 0x0022
+#define CMN_PLLSM0_PLLPRE_TMR 0x002a
+#define CMN_PLLSM0_PLLLOCK_TMR 0x002c
+#define CMN_PLLSM1_PLLPRE_TMR 0x0032
+#define CMN_PLLSM1_PLLLOCK_TMR 0x0034
+#define CMN_BGCAL_INIT_TMR 0x0064
+#define CMN_BGCAL_ITER_TMR 0x0065
+#define CMN_IBCAL_INIT_TMR 0x0074
+#define CMN_PLL0_SS_CTRL1_M0 0x0098
+#define CMN_PLL0_SS_CTRL2_M0 0x0099
+#define CMN_PLL0_SS_CTRL3_M0 0x009a
+#define CMN_PLL0_SS_CTRL4_M0 0x009b
+#define CMN_PLL1_SS_CTRL1_M0 0x00d8
+#define CMN_PLL1_SS_CTRL2_M0 0x00d9
+#define CMN_PLL1_SS_CTRL3_M0 0x00da
+#define CMN_PLL1_SS_CTRL4_M0 0x00db
+#define CMN_TXPUCAL_INIT_TMR 0x0104
+#define CMN_TXPDCAL_INIT_TMR 0x010c
+#define CMN_RXCAL_INIT_TMR 0x0114
+#define CMN_SD_CAL_PLLCNT_START 0x0128
+#define CMN_PDIAG_PLL1_ITRIM_M0 0x01c3
+#define CMN_DIAG_GPANA_0 0x01f0
+
+#define RX_SDCAL0_INIT_TMR_LANE0 0x8044
+#define RX_SDCAL0_INIT_TMR_LANE1 0x8244
+#define RX_SDCAL0_INIT_TMR_LANE2 0x8444
+#define RX_SDCAL0_INIT_TMR_LANE3 0x8644
+
+#define RX_SDCAL0_ITER_TMR_LANE0 0x8045
+#define RX_SDCAL0_ITER_TMR_LANE1 0x8245
+#define RX_SDCAL0_ITER_TMR_LANE2 0x8445
+#define RX_SDCAL0_ITER_TMR_LANE3 0x8645
+
+#define RX_SDCAL1_INIT_TMR_LANE0 0x804c
+#define RX_SDCAL1_INIT_TMR_LANE1 0x824c
+#define RX_SDCAL1_INIT_TMR_LANE2 0x844c
+#define RX_SDCAL1_INIT_TMR_LANE3 0x864c
+
+#define RX_SDCAL1_ITER_TMR_LANE0 0x804d
+#define RX_SDCAL1_ITER_TMR_LANE1 0x824d
+#define RX_SDCAL1_ITER_TMR_LANE2 0x844d
+#define RX_SDCAL1_ITER_TMR_LANE3 0x864d
+
+#define TX_RCVDET_ST_TMR_LANE0 0x4123
+#define TX_RCVDET_ST_TMR_LANE1 0x4323
+#define TX_RCVDET_ST_TMR_LANE2 0x4523
+#define TX_RCVDET_ST_TMR_LANE3 0x4723
+
+#define CMN_PDIAG_PLL0_CLK_SEL_M0 0x01a1
+#define CMN_PDIAG_PLL1_CLK_SEL_M0 0x01c1
+
+#define XCVR_DIAG_HSCLK_SEL_LANE0 0x40e6
+#define XCVR_DIAG_HSCLK_SEL_LANE1 0x42e6
+#define XCVR_DIAG_HSCLK_SEL_LANE2 0x44e6
+#define XCVR_DIAG_HSCLK_SEL_LANE3 0x46e6
+
+#define XCVR_DIAG_HSCLK_DIV_LANE0 0x40e7
+#define XCVR_DIAG_HSCLK_DIV_LANE1 0x42e7
+#define XCVR_DIAG_HSCLK_DIV_LANE2 0x44e7
+#define XCVR_DIAG_HSCLK_DIV_LANE3 0x46e7
+
+#define XCVR_DIAG_PLLDRC_CTRL_LANE0 0x40e5
+#define XCVR_DIAG_PLLDRC_CTRL_LANE1 0x42e5
+#define XCVR_DIAG_PLLDRC_CTRL_LANE2 0x44e5
+#define XCVR_DIAG_PLLDRC_CTRL_LANE3 0x46e5
+
+#define XCVR_DIAG_BIDI_CTRL_LANE0 0x40ea
+#define XCVR_DIAG_BIDI_CTRL_LANE1 0x42ea
+#define XCVR_DIAG_BIDI_CTRL_LANE2 0x44ea
+#define XCVR_DIAG_BIDI_CTRL_LANE3 0x46ea
+
+#define CMN_PLL0_DSM_DIAG_M0 0x0094
+#define CMN_PLL1_DSM_DIAG_M0 0x00d4
+#define CMN_PDIAG_PLL0_CP_PADJ_M0 0x01a4
+#define CMN_PDIAG_PLL1_CP_PADJ_M0 0x01c4
+
+#define CMN_PDIAG_PLL0_CP_IADJ_M0 0x01a5
+#define CMN_PDIAG_PLL1_CP_IADJ_M0 0x01c5
+#define CMN_PDIAG_PLL0_FILT_PADJ_M0 0x01a6
+#define CMN_PDIAG_PLL1_FILT_PADJ_M0 0x01c6
+
+#define CMN_PLL0_INTDIV_M0 0x0090
+#define CMN_PLL1_INTDIV_M0 0x00d0
+#define CMN_PLL0_FRACDIVL_M0 0x0091
+#define CMN_PLL1_FRACDIVL_M0 0x00d1
+
+#define CMN_PLL0_FRACDIVH_M0 0x0092
+#define CMN_PLL1_FRACDIVH_M0 0x00d2
+#define CMN_PLL0_HIGH_THR_M0 0x0093
+#define CMN_PLL1_HIGH_THR_M0 0x00d3
+
+#define CMN_PDIAG_PLL0_CTRL_M0 0x01a0
+#define CMN_PDIAG_PLL1_CTRL_M0 0x01c0
+
+#define CMN_PLL0_VCOCAL_TCTRL 0x0082
+#define CMN_PLL1_VCOCAL_TCTRL 0x00c2
+
+#define CMN_PLL0_VCOCAL_INIT_TMR 0x0084
+#define CMN_PLL1_VCOCAL_INIT_TMR 0x00c4
+
+#define CMN_PLL0_VCOCAL_ITER_TMR 0x0085
+#define CMN_PLL1_VCOCAL_ITER_TMR 0x00c5
+
+#define CMN_PLL0_VCOCAL_REFTIM_START 0x0086
+#define CMN_PLL1_VCOCAL_REFTIM_START 0x00c6
+
+#define CMN_PLL0_VCOCAL_PLLCNT_START 0x0088
+#define CMN_PLL1_VCOCAL_PLLCNT_START 0x00c8
+
+#define CMN_PLL0_LOCK_REFCNT_START 0x009c
+#define CMN_PLL1_LOCK_REFCNT_START 0x00dc
+
+#define CMN_PLL0_LOCK_PLLCNT_START 0x009e
+#define CMN_PLL1_LOCK_PLLCNT_START 0x00de
+
+#define CMN_PLL0_LOCK_PLLCNT_THR 0x009f
+#define CMN_PLL1_LOCK_PLLCNT_THR 0x00df
+
+#define PHY_PMA_LANE_MAP 0xc010
+#define PHY_LANE_OFF_CTRL 0xc011
+
+#define PHY_PIPE_USB3_GEN2_PRE_CFG0 0xc018
+#define PHY_PIPE_USB3_GEN2_POST_CFG0 0xc01a
+#define PHY_PIPE_USB3_GEN2_POST_CFG1 0xc01b
+
+#define CMN_CDIAG_CDB_PWRI_OVRD 0x0041
+#define CMN_CDIAG_XCVRC_PWRI_OVRD 0x0047
+
+#define TX_PSC_A0_LANE0 0x4100
+#define TX_PSC_A0_LANE1 0x4300
+#define TX_PSC_A0_LANE2 0x4500
+#define TX_PSC_A0_LANE3 0x4700
+
+#define TX_PSC_A1_LANE0 0x4101
+#define TX_PSC_A1_LANE1 0x4301
+#define TX_PSC_A1_LANE3 0x4701
+
+#define TX_PSC_A2_LANE0 0x4102
+#define TX_PSC_A2_LANE1 0x4302
+#define TX_PSC_A2_LANE2 0x4502
+#define TX_PSC_A2_LANE3 0x4702
+
+#define TX_PSC_A3_LANE0 0x4103
+#define TX_PSC_A3_LANE1 0x4303
+#define TX_PSC_A3_LANE2 0x4503
+#define TX_PSC_A3_LANE3 0x4703
+
+#define RX_PSC_A0_LANE0 0x8000
+#define RX_PSC_A0_LANE1 0x8200
+#define RX_PSC_A0_LANE2 0x8400
+#define RX_PSC_A0_LANE3 0x8600
+
+#define RX_PSC_A1_LANE0 0x8001
+#define RX_PSC_A1_LANE1 0x8201
+#define RX_PSC_A1_LANE2 0x8401
+
+#define RX_PSC_A2_LANE0 0x8002
+#define RX_PSC_A2_LANE1 0x8202
+#define RX_PSC_A2_LANE2 0x8402
+#define RX_PSC_A2_LANE3 0x8602
+
+#define RX_PSC_A3_LANE0 0x8003
+#define RX_PSC_A3_LANE1 0x8203
+#define RX_PSC_A3_LANE2 0x8403
+#define RX_PSC_A3_LANE3 0x8603
+
+#define RX_PSC_CAL_LANE0 0x8006
+#define RX_PSC_CAL_LANE1 0x8206
+#define RX_PSC_CAL_LANE2 0x8406
+#define RX_PSC_CAL_LANE3 0x8606
+
+#define TX_TXCC_CTRL_LANE0 0x4040
+#define TX_TXCC_CTRL_LANE1 0x4240
+#define TX_TXCC_CTRL_LANE2 0x4440
+#define TX_TXCC_CTRL_LANE3 0x4640
+
+#define TX_TXCC_CPOST_MULT_00_LANE0 0x404c
+#define TX_TXCC_CPOST_MULT_00_LANE1 0x424c
+#define TX_TXCC_CPOST_MULT_00_LANE2 0x444c
+#define TX_TXCC_CPOST_MULT_00_LANE3 0x464c
+
+#define TX_TXCC_CPOST_MULT_01_LANE0 0x404d
+#define TX_TXCC_CPOST_MULT_01_LANE1 0x424d
+#define TX_TXCC_CPOST_MULT_01_LANE3 0x464d
+
+#define TX_TXCC_MGNFS_MULT_000_LANE0 0x4050
+#define TX_TXCC_MGNFS_MULT_000_LANE1 0x4250
+#define TX_TXCC_MGNFS_MULT_000_LANE2 0x4450
+#define TX_TXCC_MGNFS_MULT_000_LANE3 0x4650
+
+#define TX_DIAG_ACYA_LANE0 0x41E7
+#define TX_DIAG_ACYA_LANE1 0x43E7
+#define TX_DIAG_ACYA_LANE2 0x45E7
+#define TX_DIAG_ACYA_LANE3 0x47E7
+
+#define DRV_DIAG_TX_DRV_LANE0 0x40c6
+#define DRV_DIAG_TX_DRV_LANE1 0x42c6
+#define DRV_DIAG_TX_DRV_LANE2 0x44c6
+#define DRV_DIAG_TX_DRV_LANE3 0x46c6
+
+#define RX_SIGDET_HL_FILT_TMR_LANE0 0x8090
+#define RX_SIGDET_HL_FILT_TMR_LANE1 0x8290
+#define RX_SIGDET_HL_FILT_TMR_LANE2 0x8490
+
+#define RX_REE_GCSM1_CTRL_LANE0 0x8108
+#define RX_REE_GCSM1_CTRL_LANE1 0x8308
+#define RX_REE_GCSM1_CTRL_LANE2 0x8508
+#define RX_REE_GCSM1_CTRL_LANE3 0x8708
+
+#define RX_REE_GCSM2_CTRL_LANE0 0x8110
+#define RX_REE_GCSM2_CTRL_LANE1 0x8310
+#define RX_REE_GCSM2_CTRL_LANE2 0x8510
+#define RX_REE_GCSM2_CTRL_LANE3 0x8710
+
+#define RX_REE_PERGCSM_CTRL_LANE0 0x8118
+#define RX_REE_PERGCSM_CTRL_LANE1 0x8318
+#define RX_REE_PERGCSM_CTRL_LANE2 0x8518
+#define RX_REE_PERGCSM_CTRL_LANE3 0x8718
+
+#define RX_REE_ATTEN_THR_LANE0 0x8149
+#define RX_REE_ATTEN_THR_LANE1 0x8349
+#define RX_REE_ATTEN_THR_LANE2 0x8549
+
+#define RX_REE_SMGM_CTRL1_LANE0 0x8177
+#define RX_REE_SMGM_CTRL1_LANE1 0x8377
+#define RX_REE_SMGM_CTRL1_LANE2 0x8577
+
+#define RX_REE_SMGM_CTRL2_LANE0 0x8178
+#define RX_REE_SMGM_CTRL2_LANE1 0x8378
+#define RX_REE_SMGM_CTRL2_LANE2 0x8578
+
+#define XCVR_DIAG_PSC_OVRD_LANE0 0x40eb
+#define XCVR_DIAG_PSC_OVRD_LANE1 0x42eb
+#define XCVR_DIAG_PSC_OVRD_LANE2 0x44eb
+
+#define RX_DIAG_SIGDET_TUNE_LANE0 0x81e8
+#define RX_DIAG_SIGDET_TUNE_LANE1 0x83e8
+#define RX_DIAG_SIGDET_TUNE_LANE2 0x85e8
+
+#define RX_DIAG_NQST_CTRL_LANE0 0x81e5
+#define RX_DIAG_NQST_CTRL_LANE1 0x83e5
+#define RX_DIAG_NQST_CTRL_LANE2 0x85e5
+
+#define RX_DIAG_DFE_AMP_TUNE_2_LANE0 0x81e2
+#define RX_DIAG_DFE_AMP_TUNE_2_LANE1 0x83e2
+#define RX_DIAG_DFE_AMP_TUNE_2_LANE2 0x85e2
+
+#define RX_DIAG_DFE_AMP_TUNE_3_LANE0 0x81e3
+#define RX_DIAG_DFE_AMP_TUNE_3_LANE1 0x83e3
+#define RX_DIAG_DFE_AMP_TUNE_3_LANE2 0x85e3
+
+#define RX_DIAG_PI_CAP_LANE0 0x81f5
+#define RX_DIAG_PI_CAP_LANE1 0x83f5
+#define RX_DIAG_PI_CAP_LANE2 0x85f5
+
+#define RX_DIAG_PI_RATE_LANE0 0x81f4
+#define RX_DIAG_PI_RATE_LANE1 0x83f4
+#define RX_DIAG_PI_RATE_LANE2 0x85f4
+
+#define RX_DIAG_ACYA_LANE0 0x81ff
+#define RX_DIAG_ACYA_LANE3 0x87ff
+
+#define RX_CDRLF_CNFG_LANE0 0x8080
+#define RX_CDRLF_CNFG_LANE1 0x8280
+#define RX_CDRLF_CNFG_LANE2 0x8480
+
+#define RX_CDRLF_CNFG3_LANE0 0x8082
+#define RX_CDRLF_CNFG3_LANE1 0x8282
+#define RX_CDRLF_CNFG3_LANE2 0x8482
+
+#define PHY_PMA_PLL_CTRL 0xe003
+
+#define PHY_PMA_ISO_PLL_CTRL0 0xe005
+#define PHY_PMA_ISO_PLL_CTRL1 0xe006
+
+/* Bits */
+
+#define PHY_PLL_CFG_0803 0xC00E
+/* 0803 phy register */
+#define PHY_PIPE_USB3_GEN2_PRE_CFG0_0803 0xc01c
+#define PHY_PIPE_USB3_GEN2_POST_CFG0_0803 0xc01e
+#define PHY_PIPE_USB3_GEN2_POST_CFG1_0803 0xc01f
+
+#endif
--
2.54.0
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH v7 1/2] dt-bindings: phy: Add CIX Sky1 USB3 PHY
2026-11-11 3:09 ` [PATCH v7 1/2] dt-bindings: phy: Add CIX Sky1 USB3 PHY Hongliang Yang
@ 2026-11-11 7:53 ` Krzysztof Kozlowski
0 siblings, 0 replies; 4+ messages in thread
From: Krzysztof Kozlowski @ 2026-11-11 7:53 UTC (permalink / raw)
To: Hongliang Yang, Vinod Koul, Neil Armstrong,
Manivannan Sadhasivam, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Philipp Zabel, Gary Yang, Fugang Duan
Cc: linux-phy, linux-arm-kernel, devicetree, linux-kernel,
cix-kernel-upstream
On 11/11/2026 04:09, Hongliang Yang wrote:
> Add device tree binding for the CIX Sky1 USB3 PHY, the SuperSpeedPlus
> PHY of the two USB3 Type-A ports of the SoC.
>
> The two lanes are not separate devices: they live in one register
> block, share the same clocks and resets, and are brought up by the
> same initialization sequence. The node is therefore a single PHY
> provider with #phy-cells = <0>, referenced by both controllers, and the
> driver reference counts phy_init() and phy_exit() so that the block is
> set up once for all of them.
>
> Signed-off-by: Hongliang Yang <hongliang.yang@cixtech.com>
> ---
> Changes in v7:
> - Describe the PHY as one provider of both lanes and say why. v5 had
> one child node per lane, v6 dropped them, and nothing in the binding
> or the changelog said where the second lane went.
> - Reword the description so that it describes the provider instead of
> the register programming of the block.
>
You gave me exactly 0 minutes to reply to your answer on v6. Nice
process - bury existing comments it with new version, hoping people will
move on. Dropping from DT patchwork as previous issues are not answered.
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2026-11-11 7:53 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2026-11-11 3:09 [PATCH v7 0/2] phy: Add CIX Sky1 USB3 PHY support Hongliang Yang
2026-11-11 3:09 ` [PATCH v7 1/2] dt-bindings: phy: Add CIX Sky1 USB3 PHY Hongliang Yang
2026-11-11 7:53 ` Krzysztof Kozlowski
2026-11-11 3:09 ` [PATCH v7 2/2] phy: cix: Add CIX Sky1 USB3 PHY driver Hongliang Yang
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®