[PATCH v4 03/11] arm64: dts: freescale: imx8mm-var-som: Update FEC support with MaxLinear PHY

[Stefano Radaelli <stefano.radaelli21@gmail.com>]

From: Stefano Radaelli <stefano.r@variscite.com>

Update the FEC Ethernet controller on the i.MX8MM VAR-SOM to match the
latest SOM hardware revision using the integrated MaxLinear MXL86110 PHY.

Add the PHY VDDIO supply regulator, adjust reset timings and add a
pinctrl sleep state for low-power operation.

The PHY LED signals originate on the SOM, but the actual LEDs are part
of the carrier implementation (RJ45 connector). Move the LED
configuration to the Symphony carrier device tree, matching the
evaluation board LED wiring.

Wake-on-LAN via magic packet is not supported at the VAR-SOM level and
is therefore not enabled in the SOM device tree nor in the official
evaluation carrier board configuration (symphony).
Designs requiring WoL support may enable it in their own carrier-specific
device trees if properly integrated at the hardware level.

Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
---
v3->v4:
 - Remove wrong enet reset gpio hog

v2->v3:
 - 

v1->v2:
 - Moved phy LED configurations to symphony dts

 .../dts/freescale/imx8mm-var-som-symphony.dts | 20 +++++++++-
 .../boot/dts/freescale/imx8mm-var-som.dtsi    | 39 +++++++++++++++++--
 2 files changed, 55 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts b/arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts
index 819707e6f3bf..9f4e004f0a37 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 
+#include <dt-bindings/leds/common.h>
 #include "imx8mm-var-som.dtsi"
 
 / {
@@ -71,7 +72,24 @@ led {
 };
 
 &ethphy {
-	reset-gpios = <&pca9534 5 GPIO_ACTIVE_HIGH>;
+	leds {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@0 {
+			reg = <0>;
+			color = <LED_COLOR_ID_YELLOW>;
+			function = LED_FUNCTION_LAN;
+			linux,default-trigger = "netdev";
+		};
+
+		led@1 {
+			reg = <1>;
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_LAN;
+			linux,default-trigger = "netdev";
+		};
+	};
 };
 
 &i2c2 {
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi
index da3c7332ec34..24924ee1e8c7 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi
@@ -24,6 +24,13 @@ reg_eth_phy: regulator-eth-phy {
 		gpio = <&gpio2 9 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 	};
+
+	reg_phy_vddio: regulator-phy-vddio {
+		compatible = "regulator-fixed";
+		regulator-name = "vddio-1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
 };
 
 &A53_0 {
@@ -99,12 +106,17 @@ touchscreen@0 {
 };
 
 &fec1 {
-	pinctrl-names = "default";
+	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&pinctrl_fec1>;
+	pinctrl-1 = <&pinctrl_fec1_sleep>;
+	/*
+	 * The required RGMII TX and RX 2ns delays are implemented directly
+	 * in hardware via passive delay elements on the SOM PCB.
+	 * No delay configuration is needed in software via PHY driver.
+	 */
 	phy-mode = "rgmii";
 	phy-handle = <&ethphy>;
 	phy-supply = <&reg_eth_phy>;
-	fsl,magic-packet;
 	status = "okay";
 
 	mdio {
@@ -116,7 +128,8 @@ ethphy: ethernet-phy@4 {
 			reg = <4>;
 			reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
 			reset-assert-us = <10000>;
-			reset-deassert-us = <10000>;
+			reset-deassert-us = <100000>;
+			vddio-supply = <&reg_phy_vddio>;
 		};
 	};
 };
@@ -366,6 +379,26 @@ MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x19
 		>;
 	};
 
+	pinctrl_fec1_sleep: fec1sleepgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ENET_MDC_GPIO1_IO16		0x120
+			MX8MM_IOMUXC_ENET_MDIO_GPIO1_IO17		0x120
+			MX8MM_IOMUXC_ENET_TD3_GPIO1_IO18		0x120
+			MX8MM_IOMUXC_ENET_TD2_GPIO1_IO19		0x120
+			MX8MM_IOMUXC_ENET_TD1_GPIO1_IO20		0x120
+			MX8MM_IOMUXC_ENET_TD0_GPIO1_IO21		0x120
+			MX8MM_IOMUXC_ENET_RD3_GPIO1_IO29		0x120
+			MX8MM_IOMUXC_ENET_RD2_GPIO1_IO28		0x120
+			MX8MM_IOMUXC_ENET_RD1_GPIO1_IO27		0x120
+			MX8MM_IOMUXC_ENET_RD0_GPIO1_IO26		0x120
+			MX8MM_IOMUXC_ENET_TXC_GPIO1_IO23		0x120
+			MX8MM_IOMUXC_ENET_RXC_GPIO1_IO25		0x120
+			MX8MM_IOMUXC_ENET_RX_CTL_GPIO1_IO24		0x120
+			MX8MM_IOMUXC_ENET_TX_CTL_GPIO1_IO22		0x120
+			MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x100
+		>;
+	};
+
 	pinctrl_i2c1: i2c1grp {
 		fsl,pins = <
 			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x400001c3
-- 
2.47.3