[PATCH v4 0/5] thermal: qcom-spmi-temp-alarm: Add support for new TEMP_ALARM subtypes

[PATCH v4 0/5] thermal: qcom-spmi-temp-alarm: Add support for new TEMP_ALARM subtypes

[Anjelique Melendez]

Add support in the qcom-spmi-temp-alarm driver for the new PMIC
TEMP_ALARM peripheral subtypes: GEN2 rev 2 and LITE. The GEN2 rev 2
subtype provides greater flexibility in temperature threshold
specification by using an independent register value to configure
each of the three thresholds. The LITE subtype utilizes a simplified
set of control registers to configure two thresholds: warning and
shutdown. While at it refactor the qcom-spmi-temp-alarm driver to limit
code reuse and if/else statements when deciphering between TEMP_ALARM 
peripheral subtypes. 

Also add support to avoid a potential issue on certain versions of
the TEMP_ALARM GEN2 subtype when automatic stage 2 partial shutdown
is disabled.

This patch series is a continuation of older series from 7/2024
(https://lore.kernel.org/all/20240729231259.2122976-1-quic_amelende@quicinc.com/)
but current series has been reworked to address the change in thermal framework to
update .set_trip_temp() callback function variables
(https://lore.kernel.org/all/8392906.T7Z3S40VBb@rjwysocki.net/)

Changes since v3:
  - Updated order of logic and made dig revision a local variable 
    in patch 1/5
  - Updated Locking Logic in patches 3/5, 4/5, 5/5
  - link: https://lore.kernel.org/all/20250320202408.3940777-1-anjelique.melendez@oss.qualcomm.com/
Changes since v2:
  - Updated function name to include "gen1" in patch 2/5
  - Added Dmitry's reviewed-by tag in patch 2/5
  - link: https://lore.kernel.org/all/20250225192429.2328092-1-anjelique.melendez@oss.qualcomm.com/
Changes since v1:
  - Remove unnecessary moving of code
  - Added new v2 patch 3/5 add a preparation patch to v1 patch 2/5
  - Updated temp alarm data function names to be consistently named
  - link: https://lore.kernel.org/all/20250213210403.3396392-1-anjelique.melendez@oss.qualcomm.com/


Anjelique Melendez (4):
  thermal: qcom-spmi-temp-alarm: Add temp alarm data struct based on HW
    subtype
  thermal: qcom-spmi-temp-alarm: Prepare to support additional Temp
    Alarm subtypes
  thermal: qcom-spmi-temp-alarm: add support for GEN2 rev 2 PMIC
    peripherals
  thermal: qcom-spmi-temp-alarm: add support for LITE PMIC peripherals

David Collins (1):
  thermal: qcom-spmi-temp-alarm: enable stage 2 shutdown when required

 drivers/thermal/qcom/qcom-spmi-temp-alarm.c | 522 ++++++++++++++++++--
 1 file changed, 472 insertions(+), 50 deletions(-)

-- 
2.34.1

[PATCH v4 1/5] thermal: qcom-spmi-temp-alarm: enable stage 2 shutdown when required

[Anjelique Melendez]

From: David Collins <david.collins@oss.qualcomm.com>

Certain TEMP_ALARM GEN2 PMIC peripherals need over-temperature
stage 2 automatic PMIC partial shutdown to be enabled in order to
avoid repeated faults in the event of reaching over-temperature
stage 3.  Modify the stage 2 shutdown control logic to ensure that
stage 2 shutdown is enabled on all affected PMICs.  Read the
digital major and minor revision registers to identify these
PMICs.

Signed-off-by: David Collins <david.collins@oss.qualcomm.com>
Signed-off-by: Anjelique Melendez <anjelique.melendez@oss.qualcomm.com>
---
 drivers/thermal/qcom/qcom-spmi-temp-alarm.c | 32 +++++++++++++++++++--
 1 file changed, 29 insertions(+), 3 deletions(-)

diff --git a/drivers/thermal/qcom/qcom-spmi-temp-alarm.c b/drivers/thermal/qcom/qcom-spmi-temp-alarm.c
index a81e7d6e865f..47248a843591 100644
--- a/drivers/thermal/qcom/qcom-spmi-temp-alarm.c
+++ b/drivers/thermal/qcom/qcom-spmi-temp-alarm.c
@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright (c) 2011-2015, 2017, 2020, The Linux Foundation. All rights reserved.
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
  */
 
 #include <linux/bitops.h>
@@ -16,6 +17,7 @@
 
 #include "../thermal_hwmon.h"
 
+#define QPNP_TM_REG_DIG_MINOR		0x00
 #define QPNP_TM_REG_DIG_MAJOR		0x01
 #define QPNP_TM_REG_TYPE		0x04
 #define QPNP_TM_REG_SUBTYPE		0x05
@@ -78,6 +80,7 @@ struct qpnp_tm_chip {
 	/* protects .thresh, .stage and chip registers */
 	struct mutex			lock;
 	bool				initialized;
+	bool				require_s2_shutdown;
 
 	struct iio_channel		*adc;
 	const long			(*temp_map)[THRESH_COUNT][STAGE_COUNT];
@@ -255,7 +258,7 @@ static int qpnp_tm_update_critical_trip_temp(struct qpnp_tm_chip *chip,
 
 skip:
 	reg |= chip->thresh;
-	if (disable_s2_shutdown)
+	if (disable_s2_shutdown && !chip->require_s2_shutdown)
 		reg |= SHUTDOWN_CTRL1_OVERRIDE_S2;
 
 	return qpnp_tm_write(chip, QPNP_TM_REG_SHUTDOWN_CTRL1, reg);
@@ -350,8 +353,8 @@ static int qpnp_tm_probe(struct platform_device *pdev)
 {
 	struct qpnp_tm_chip *chip;
 	struct device_node *node;
-	u8 type, subtype, dig_major;
-	u32 res;
+	u8 type, subtype, dig_major, dig_minor;
+	u32 res, dig_revision;
 	int ret, irq;
 
 	node = pdev->dev.of_node;
@@ -402,6 +405,12 @@ static int qpnp_tm_probe(struct platform_device *pdev)
 		return dev_err_probe(&pdev->dev, ret,
 				     "could not read dig_major\n");
 
+	ret = qpnp_tm_read(chip, QPNP_TM_REG_DIG_MINOR, &dig_minor);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "could not read dig_minor\n");
+		return ret;
+	}
+
 	if (type != QPNP_TM_TYPE || (subtype != QPNP_TM_SUBTYPE_GEN1
 				     && subtype != QPNP_TM_SUBTYPE_GEN2)) {
 		dev_err(&pdev->dev, "invalid type 0x%02x or subtype 0x%02x\n",
@@ -415,6 +424,23 @@ static int qpnp_tm_probe(struct platform_device *pdev)
 	else
 		chip->temp_map = &temp_map_gen1;
 
+	if (chip->subtype == QPNP_TM_SUBTYPE_GEN2) {
+		dig_revision = (dig_major << 8) | dig_minor;
+		/*
+		 * Check if stage 2 automatic partial shutdown must remain
+		 * enabled to avoid potential repeated faults upon reaching
+		 * over-temperature stage 3.
+		 */
+		switch (dig_revision) {
+		case 0x0001:
+		case 0x0002:
+		case 0x0100:
+		case 0x0101:
+			chip->require_s2_shutdown = true;
+			break;
+		}
+	}
+
 	/*
 	 * Register the sensor before initializing the hardware to be able to
 	 * read the trip points. get_temp() returns the default temperature
-- 
2.34.1

Re: [PATCH v4 1/5] thermal: qcom-spmi-temp-alarm: enable stage 2 shutdown when required

[Bryan O'Donoghue]

On 29/05/2025 00:50, Anjelique Melendez wrote:
> From: David Collins <david.collins@oss.qualcomm.com>
> 
> Certain TEMP_ALARM GEN2 PMIC peripherals need over-temperature
> stage 2 automatic PMIC partial shutdown to be enabled in order to

stage 2 should be hyphenated to stage-2

> avoid repeated faults in the event of reaching over-temperature
> stage 3.  Modify the stage 2 shutdown control logic to ensure that
> stage 2 shutdown is enabled on all affected PMICs.  Read the
> digital major and minor revision registers to identify these
> PMICs.
> 
> Signed-off-by: David Collins <david.collins@oss.qualcomm.com>
> Signed-off-by: Anjelique Melendez <anjelique.melendez@oss.qualcomm.com>
> ---
>   drivers/thermal/qcom/qcom-spmi-temp-alarm.c | 32 +++++++++++++++++++--
>   1 file changed, 29 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/thermal/qcom/qcom-spmi-temp-alarm.c b/drivers/thermal/qcom/qcom-spmi-temp-alarm.c
> index a81e7d6e865f..47248a843591 100644
> --- a/drivers/thermal/qcom/qcom-spmi-temp-alarm.c
> +++ b/drivers/thermal/qcom/qcom-spmi-temp-alarm.c
> @@ -1,6 +1,7 @@
>   // SPDX-License-Identifier: GPL-2.0-only
>   /*
>    * Copyright (c) 2011-2015, 2017, 2020, The Linux Foundation. All rights reserved.
> + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.

Should have the year in it.

grep -r Copyright * | grep Qualcomm

>    */
> 
>   #include <linux/bitops.h>
> @@ -16,6 +17,7 @@
> 
>   #include "../thermal_hwmon.h"
> 
> +#define QPNP_TM_REG_DIG_MINOR		0x00
>   #define QPNP_TM_REG_DIG_MAJOR		0x01
>   #define QPNP_TM_REG_TYPE		0x04
>   #define QPNP_TM_REG_SUBTYPE		0x05
> @@ -78,6 +80,7 @@ struct qpnp_tm_chip {
>   	/* protects .thresh, .stage and chip registers */
>   	struct mutex			lock;
>   	bool				initialized;
> +	bool				require_s2_shutdown;
> 
>   	struct iio_channel		*adc;
>   	const long			(*temp_map)[THRESH_COUNT][STAGE_COUNT];
> @@ -255,7 +258,7 @@ static int qpnp_tm_update_critical_trip_temp(struct qpnp_tm_chip *chip,
> 
>   skip:
>   	reg |= chip->thresh;
> -	if (disable_s2_shutdown)
> +	if (disable_s2_shutdown && !chip->require_s2_shutdown)
>   		reg |= SHUTDOWN_CTRL1_OVERRIDE_S2;
> 
>   	return qpnp_tm_write(chip, QPNP_TM_REG_SHUTDOWN_CTRL1, reg);
> @@ -350,8 +353,8 @@ static int qpnp_tm_probe(struct platform_device *pdev)
>   {
>   	struct qpnp_tm_chip *chip;
>   	struct device_node *node;
> -	u8 type, subtype, dig_major;
> -	u32 res;
> +	u8 type, subtype, dig_major, dig_minor;
> +	u32 res, dig_revision;
>   	int ret, irq;
> 
>   	node = pdev->dev.of_node;
> @@ -402,6 +405,12 @@ static int qpnp_tm_probe(struct platform_device *pdev)
>   		return dev_err_probe(&pdev->dev, ret,
>   				     "could not read dig_major\n");
> 
> +	ret = qpnp_tm_read(chip, QPNP_TM_REG_DIG_MINOR, &dig_minor);
> +	if (ret < 0) {
> +		dev_err(&pdev->dev, "could not read dig_minor\n");
> +		return ret;
> +	}
> +
>   	if (type != QPNP_TM_TYPE || (subtype != QPNP_TM_SUBTYPE_GEN1
>   				     && subtype != QPNP_TM_SUBTYPE_GEN2)) {
>   		dev_err(&pdev->dev, "invalid type 0x%02x or subtype 0x%02x\n",
> @@ -415,6 +424,23 @@ static int qpnp_tm_probe(struct platform_device *pdev)
>   	else
>   		chip->temp_map = &temp_map_gen1;
> 
> +	if (chip->subtype == QPNP_TM_SUBTYPE_GEN2) {
> +		dig_revision = (dig_major << 8) | dig_minor;
> +		/*
> +		 * Check if stage 2 automatic partial shutdown must remain
> +		 * enabled to avoid potential repeated faults upon reaching
> +		 * over-temperature stage 3.
> +		 */
> +		switch (dig_revision) {
> +		case 0x0001:
> +		case 0x0002:
> +		case 0x0100:
> +		case 0x0101:
> +			chip->require_s2_shutdown = true;
> +			break;
> +		}
> +	}
> +
>   	/*
>   	 * Register the sensor before initializing the hardware to be able to
>   	 * read the trip points. get_temp() returns the default temperature
> --
> 2.34.1
> 
> 
---
bod

Re: [PATCH v4 1/5] thermal: qcom-spmi-temp-alarm: enable stage 2 shutdown when required

[Dmitry Baryshkov]

On Thu, May 29, 2025 at 11:34:27AM +0100, Bryan O'Donoghue wrote:
> On 29/05/2025 00:50, Anjelique Melendez wrote:
> > From: David Collins <david.collins@oss.qualcomm.com>
> > 
> > Certain TEMP_ALARM GEN2 PMIC peripherals need over-temperature
> > stage 2 automatic PMIC partial shutdown to be enabled in order to
> 
> stage 2 should be hyphenated to stage-2
> 
> > avoid repeated faults in the event of reaching over-temperature
> > stage 3.  Modify the stage 2 shutdown control logic to ensure that
> > stage 2 shutdown is enabled on all affected PMICs.  Read the
> > digital major and minor revision registers to identify these
> > PMICs.
> > 
> > Signed-off-by: David Collins <david.collins@oss.qualcomm.com>
> > Signed-off-by: Anjelique Melendez <anjelique.melendez@oss.qualcomm.com>
> > ---
> >   drivers/thermal/qcom/qcom-spmi-temp-alarm.c | 32 +++++++++++++++++++--
> >   1 file changed, 29 insertions(+), 3 deletions(-)
> > 
> > diff --git a/drivers/thermal/qcom/qcom-spmi-temp-alarm.c b/drivers/thermal/qcom/qcom-spmi-temp-alarm.c
> > index a81e7d6e865f..47248a843591 100644
> > --- a/drivers/thermal/qcom/qcom-spmi-temp-alarm.c
> > +++ b/drivers/thermal/qcom/qcom-spmi-temp-alarm.c
> > @@ -1,6 +1,7 @@
> >   // SPDX-License-Identifier: GPL-2.0-only
> >   /*
> >    * Copyright (c) 2011-2015, 2017, 2020, The Linux Foundation. All rights reserved.
> > + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
> 
> Should have the year in it.

Not per the new policy...

> 
> grep -r Copyright * | grep Qualcomm
> 
> >    */
> > 
> >   #include <linux/bitops.h>

-- 
With best wishes
Dmitry

[PATCH v4 2/5] thermal: qcom-spmi-temp-alarm: Add temp alarm data struct based on HW subtype

[Anjelique Melendez]

Currently multiple if/else statements are used in functions to decipher
between SPMI temp alarm Gen 1, Gen 2 and Gen 2 Rev 1 functionality. Instead
refactor the driver so that SPMI temp alarm chips will have reference to a
spmi_temp_alarm_data struct which defines data and function callbacks
based on the HW subtype.

Signed-off-by: Anjelique Melendez <anjelique.melendez@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 drivers/thermal/qcom/qcom-spmi-temp-alarm.c | 106 +++++++++++++-------
 1 file changed, 69 insertions(+), 37 deletions(-)

diff --git a/drivers/thermal/qcom/qcom-spmi-temp-alarm.c b/drivers/thermal/qcom/qcom-spmi-temp-alarm.c
index 47248a843591..0d8bbc5b7af6 100644
--- a/drivers/thermal/qcom/qcom-spmi-temp-alarm.c
+++ b/drivers/thermal/qcom/qcom-spmi-temp-alarm.c
@@ -4,6 +4,7 @@
  * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
  */
 
+#include <linux/bitfield.h>
 #include <linux/bitops.h>
 #include <linux/delay.h>
 #include <linux/err.h>
@@ -31,7 +32,6 @@
 
 #define STATUS_GEN1_STAGE_MASK		GENMASK(1, 0)
 #define STATUS_GEN2_STATE_MASK		GENMASK(6, 4)
-#define STATUS_GEN2_STATE_SHIFT		4
 
 #define SHUTDOWN_CTRL1_OVERRIDE_S2	BIT(6)
 #define SHUTDOWN_CTRL1_THRESHOLD_MASK	GENMASK(1, 0)
@@ -68,10 +68,18 @@ static const long temp_map_gen2_v1[THRESH_COUNT][STAGE_COUNT] = {
 /* Temperature in Milli Celsius reported during stage 0 if no ADC is present */
 #define DEFAULT_TEMP			37000
 
+struct qpnp_tm_chip;
+
+struct spmi_temp_alarm_data {
+	const long (*temp_map)[THRESH_COUNT][STAGE_COUNT];
+	int (*get_temp_stage)(struct qpnp_tm_chip *chip);
+};
+
 struct qpnp_tm_chip {
 	struct regmap			*map;
 	struct device			*dev;
 	struct thermal_zone_device	*tz_dev;
+	const struct spmi_temp_alarm_data *data;
 	unsigned int			subtype;
 	long				temp;
 	unsigned int			thresh;
@@ -81,9 +89,9 @@ struct qpnp_tm_chip {
 	struct mutex			lock;
 	bool				initialized;
 	bool				require_s2_shutdown;
+	long				temp_thresh_map[STAGE_COUNT];
 
 	struct iio_channel		*adc;
-	const long			(*temp_map)[THRESH_COUNT][STAGE_COUNT];
 };
 
 /* This array maps from GEN2 alarm state to GEN1 alarm stage */
@@ -117,20 +125,19 @@ static int qpnp_tm_write(struct qpnp_tm_chip *chip, u16 addr, u8 data)
  */
 static long qpnp_tm_decode_temp(struct qpnp_tm_chip *chip, unsigned int stage)
 {
-	if (!chip->temp_map || chip->thresh >= THRESH_COUNT || stage == 0 ||
-	    stage > STAGE_COUNT)
+	if (stage == 0 || stage > STAGE_COUNT)
 		return 0;
 
-	return (*chip->temp_map)[chip->thresh][stage - 1];
+	return chip->temp_thresh_map[stage - 1];
 }
 
 /**
- * qpnp_tm_get_temp_stage() - return over-temperature stage
+ * qpnp_tm_gen1_get_temp_stage() - return over-temperature stage
  * @chip:		Pointer to the qpnp_tm chip
  *
- * Return: stage (GEN1) or state (GEN2) on success, or errno on failure.
+ * Return: stage on success, or errno on failure.
  */
-static int qpnp_tm_get_temp_stage(struct qpnp_tm_chip *chip)
+static int qpnp_tm_gen1_get_temp_stage(struct qpnp_tm_chip *chip)
 {
 	int ret;
 	u8 reg = 0;
@@ -139,12 +146,27 @@ static int qpnp_tm_get_temp_stage(struct qpnp_tm_chip *chip)
 	if (ret < 0)
 		return ret;
 
-	if (chip->subtype == QPNP_TM_SUBTYPE_GEN1)
-		ret = reg & STATUS_GEN1_STAGE_MASK;
-	else
-		ret = (reg & STATUS_GEN2_STATE_MASK) >> STATUS_GEN2_STATE_SHIFT;
+	return FIELD_GET(STATUS_GEN1_STAGE_MASK, reg);
+}
 
-	return ret;
+/**
+ * qpnp_tm_gen2_get_temp_stage() - return over-temperature stage
+ * @chip:		Pointer to the qpnp_tm chip
+ *
+ * Return: stage on success, or errno on failure.
+ */
+static int qpnp_tm_gen2_get_temp_stage(struct qpnp_tm_chip *chip)
+{
+	u8 reg = 0;
+	int ret;
+
+	ret = qpnp_tm_read(chip, QPNP_TM_REG_STATUS, &reg);
+	if (ret < 0)
+		return ret;
+
+	ret = FIELD_GET(STATUS_GEN2_STATE_MASK, reg);
+
+	return alarm_state_map[ret];
 }
 
 /*
@@ -153,23 +175,16 @@ static int qpnp_tm_get_temp_stage(struct qpnp_tm_chip *chip)
  */
 static int qpnp_tm_update_temp_no_adc(struct qpnp_tm_chip *chip)
 {
-	unsigned int stage, stage_new, stage_old;
+	unsigned int stage_new, stage_old;
 	int ret;
 
 	WARN_ON(!mutex_is_locked(&chip->lock));
 
-	ret = qpnp_tm_get_temp_stage(chip);
+	ret = chip->data->get_temp_stage(chip);
 	if (ret < 0)
 		return ret;
-	stage = ret;
-
-	if (chip->subtype == QPNP_TM_SUBTYPE_GEN1) {
-		stage_new = stage;
-		stage_old = chip->stage;
-	} else {
-		stage_new = alarm_state_map[stage];
-		stage_old = alarm_state_map[chip->stage];
-	}
+	stage_new = ret;
+	stage_old = chip->stage;
 
 	if (stage_new > stage_old) {
 		/* increasing stage, use lower bound */
@@ -181,7 +196,7 @@ static int qpnp_tm_update_temp_no_adc(struct qpnp_tm_chip *chip)
 				- TEMP_STAGE_HYSTERESIS;
 	}
 
-	chip->stage = stage;
+	chip->stage = stage_new;
 
 	return 0;
 }
@@ -221,8 +236,8 @@ static int qpnp_tm_get_temp(struct thermal_zone_device *tz, int *temp)
 static int qpnp_tm_update_critical_trip_temp(struct qpnp_tm_chip *chip,
 					     int temp)
 {
-	long stage2_threshold_min = (*chip->temp_map)[THRESH_MIN][1];
-	long stage2_threshold_max = (*chip->temp_map)[THRESH_MAX][1];
+	long stage2_threshold_min = (*chip->data->temp_map)[THRESH_MIN][1];
+	long stage2_threshold_max = (*chip->data->temp_map)[THRESH_MAX][1];
 	bool disable_s2_shutdown = false;
 	u8 reg;
 
@@ -257,6 +272,8 @@ static int qpnp_tm_update_critical_trip_temp(struct qpnp_tm_chip *chip,
 	}
 
 skip:
+	memcpy(chip->temp_thresh_map, chip->data->temp_map[chip->thresh],
+		sizeof(chip->temp_thresh_map));
 	reg |= chip->thresh;
 	if (disable_s2_shutdown && !chip->require_s2_shutdown)
 		reg |= SHUTDOWN_CTRL1_OVERRIDE_S2;
@@ -294,6 +311,21 @@ static irqreturn_t qpnp_tm_isr(int irq, void *data)
 	return IRQ_HANDLED;
 }
 
+static const struct spmi_temp_alarm_data spmi_temp_alarm_data = {
+	.temp_map = &temp_map_gen1,
+	.get_temp_stage = qpnp_tm_gen1_get_temp_stage,
+};
+
+static const struct spmi_temp_alarm_data spmi_temp_alarm_gen2_data = {
+	.temp_map = &temp_map_gen1,
+	.get_temp_stage = qpnp_tm_gen2_get_temp_stage,
+};
+
+static const struct spmi_temp_alarm_data spmi_temp_alarm_gen2_rev1_data = {
+	.temp_map = &temp_map_gen2_v1,
+	.get_temp_stage = qpnp_tm_gen2_get_temp_stage,
+};
+
 /*
  * This function initializes the internal temp value based on only the
  * current thermal stage and threshold. Setup threshold control and
@@ -301,7 +333,6 @@ static irqreturn_t qpnp_tm_isr(int irq, void *data)
  */
 static int qpnp_tm_init(struct qpnp_tm_chip *chip)
 {
-	unsigned int stage;
 	int ret;
 	u8 reg = 0;
 	int crit_temp;
@@ -315,16 +346,13 @@ static int qpnp_tm_init(struct qpnp_tm_chip *chip)
 	chip->thresh = reg & SHUTDOWN_CTRL1_THRESHOLD_MASK;
 	chip->temp = DEFAULT_TEMP;
 
-	ret = qpnp_tm_get_temp_stage(chip);
+	ret = chip->data->get_temp_stage(chip);
 	if (ret < 0)
 		goto out;
 	chip->stage = ret;
 
-	stage = chip->subtype == QPNP_TM_SUBTYPE_GEN1
-		? chip->stage : alarm_state_map[chip->stage];
-
-	if (stage)
-		chip->temp = qpnp_tm_decode_temp(chip, stage);
+	if (chip->stage)
+		chip->temp = qpnp_tm_decode_temp(chip, chip->stage);
 
 	mutex_unlock(&chip->lock);
 
@@ -419,10 +447,14 @@ static int qpnp_tm_probe(struct platform_device *pdev)
 	}
 
 	chip->subtype = subtype;
-	if (subtype == QPNP_TM_SUBTYPE_GEN2 && dig_major >= 1)
-		chip->temp_map = &temp_map_gen2_v1;
+	if (subtype == QPNP_TM_SUBTYPE_GEN1)
+		chip->data = &spmi_temp_alarm_data;
+	else if (subtype == QPNP_TM_SUBTYPE_GEN2 && dig_major >= 1)
+		chip->data = &spmi_temp_alarm_gen2_rev1_data;
+	else if (subtype == QPNP_TM_SUBTYPE_GEN2)
+		chip->data = &spmi_temp_alarm_gen2_data;
 	else
-		chip->temp_map = &temp_map_gen1;
+		return -ENODEV;
 
 	if (chip->subtype == QPNP_TM_SUBTYPE_GEN2) {
 		dig_revision = (dig_major << 8) | dig_minor;
-- 
2.34.1

[PATCH v4 3/5] thermal: qcom-spmi-temp-alarm: Prepare to support additional Temp Alarm subtypes

[Anjelique Melendez]

In preparation to support newer temp alarm subtypes, add the "ops" and
"configure_trip_temps" references to spmi_temp_alarm_data. This will
allow for each Temp Alarm subtype to define its own
thermal_zone_device_ops and properly configure thermal trip temperature.

Signed-off-by: Anjelique Melendez <anjelique.melendez@oss.qualcomm.com>
---
 drivers/thermal/qcom/qcom-spmi-temp-alarm.c | 36 +++++++++++++++------
 1 file changed, 27 insertions(+), 9 deletions(-)

diff --git a/drivers/thermal/qcom/qcom-spmi-temp-alarm.c b/drivers/thermal/qcom/qcom-spmi-temp-alarm.c
index 0d8bbc5b7af6..59a25f02a278 100644
--- a/drivers/thermal/qcom/qcom-spmi-temp-alarm.c
+++ b/drivers/thermal/qcom/qcom-spmi-temp-alarm.c
@@ -71,8 +71,10 @@ static const long temp_map_gen2_v1[THRESH_COUNT][STAGE_COUNT] = {
 struct qpnp_tm_chip;
 
 struct spmi_temp_alarm_data {
+	const struct thermal_zone_device_ops *ops;
 	const long (*temp_map)[THRESH_COUNT][STAGE_COUNT];
 	int (*get_temp_stage)(struct qpnp_tm_chip *chip);
+	int (*configure_trip_temps)(struct qpnp_tm_chip *chip);
 };
 
 struct qpnp_tm_chip {
@@ -311,18 +313,39 @@ static irqreturn_t qpnp_tm_isr(int irq, void *data)
 	return IRQ_HANDLED;
 }
 
+static int qpnp_tm_configure_trip_temp(struct qpnp_tm_chip *chip)
+{
+	int crit_temp, ret;
+
+	ret = thermal_zone_get_crit_temp(chip->tz_dev, &crit_temp);
+	if (ret)
+		crit_temp = THERMAL_TEMP_INVALID;
+
+	mutex_lock(&chip->lock);
+	ret = qpnp_tm_update_critical_trip_temp(chip, crit_temp);
+	mutex_unlock(&chip->lock);
+
+	return ret;
+}
+
 static const struct spmi_temp_alarm_data spmi_temp_alarm_data = {
+	.ops = &qpnp_tm_sensor_ops,
 	.temp_map = &temp_map_gen1,
+	.configure_trip_temps = qpnp_tm_configure_trip_temp,
 	.get_temp_stage = qpnp_tm_gen1_get_temp_stage,
 };
 
 static const struct spmi_temp_alarm_data spmi_temp_alarm_gen2_data = {
+	.ops = &qpnp_tm_sensor_ops,
 	.temp_map = &temp_map_gen1,
+	.configure_trip_temps = qpnp_tm_configure_trip_temp,
 	.get_temp_stage = qpnp_tm_gen2_get_temp_stage,
 };
 
 static const struct spmi_temp_alarm_data spmi_temp_alarm_gen2_rev1_data = {
+	.ops = &qpnp_tm_sensor_ops,
 	.temp_map = &temp_map_gen2_v1,
+	.configure_trip_temps = qpnp_tm_configure_trip_temp,
 	.get_temp_stage = qpnp_tm_gen2_get_temp_stage,
 };
 
@@ -335,7 +358,6 @@ static int qpnp_tm_init(struct qpnp_tm_chip *chip)
 {
 	int ret;
 	u8 reg = 0;
-	int crit_temp;
 
 	mutex_lock(&chip->lock);
 
@@ -356,16 +378,12 @@ static int qpnp_tm_init(struct qpnp_tm_chip *chip)
 
 	mutex_unlock(&chip->lock);
 
-	ret = thermal_zone_get_crit_temp(chip->tz_dev, &crit_temp);
-	if (ret)
-		crit_temp = THERMAL_TEMP_INVALID;
+	ret = chip->data->configure_trip_temps(chip);
+	if (ret < 0)
+		return ret;
 
 	mutex_lock(&chip->lock);
 
-	ret = qpnp_tm_update_critical_trip_temp(chip, crit_temp);
-	if (ret < 0)
-		goto out;
-
 	/* Enable the thermal alarm PMIC module in always-on mode. */
 	reg = ALARM_CTRL_FORCE_ENABLE;
 	ret = qpnp_tm_write(chip, QPNP_TM_REG_ALARM_CTRL, reg);
@@ -479,7 +497,7 @@ static int qpnp_tm_probe(struct platform_device *pdev)
 	 * before the hardware initialization is completed.
 	 */
 	chip->tz_dev = devm_thermal_of_zone_register(
-		&pdev->dev, 0, chip, &qpnp_tm_sensor_ops);
+		&pdev->dev, 0, chip, chip->data->ops);
 	if (IS_ERR(chip->tz_dev))
 		return dev_err_probe(&pdev->dev, PTR_ERR(chip->tz_dev),
 				     "failed to register sensor\n");
-- 
2.34.1

Re: [PATCH v4 3/5] thermal: qcom-spmi-temp-alarm: Prepare to support additional Temp Alarm subtypes

[Bryan O'Donoghue]

On 29/05/2025 00:50, Anjelique Melendez wrote:
> @@ -356,16 +378,12 @@ static int qpnp_tm_init(struct qpnp_tm_chip *chip)
> 
>   	mutex_unlock(&chip->lock);
> 
> -	ret = thermal_zone_get_crit_temp(chip->tz_dev, &crit_temp);
> -	if (ret)
> -		crit_temp = THERMAL_TEMP_INVALID;
> +	ret = chip->data->configure_trip_temps(chip);
> +	if (ret < 0)
> +		return ret;
> 
>   	mutex_lock(&chip->lock);

Could we just drop the mutex lock in tm_init ();

probe()
   tm_init();
     mutex_lock();
     do stuff;
     mutex_unlock();
     ->configure_trip_temps();
         mutex_lock();
         do other stuff
         mutex_unlock();
     mutex_lock();
     back to doing stuff in tm_init();
     mutex_unlock();

There's little rationality to tm_init() being a critical section but 
also doing lock/unlock three times inside of that critical section.

Since tm_init() is only called during probe() what exactly is the 
parallel context we are premepting with the lock ?

If we can't answer that question the tm_init() mutex should be dropped.

---
bod

[PATCH v4 4/5] thermal: qcom-spmi-temp-alarm: add support for GEN2 rev 2 PMIC peripherals

[Anjelique Melendez]

Add support for TEMP_ALARM GEN2 PMIC peripherals with digital major
revision 2.  This revision utilizes individual temp DAC registers
to set the threshold temperature for over-temperature stages 1 (warning),
2 (system shutdown), and 3 (emergency shutdown) instead of a single
register to specify a set of thresholds.

Signed-off-by: David Collins <david.collins@oss.qualcomm.com>
Signed-off-by: Anjelique Melendez <anjelique.melendez@oss.qualcomm.com>
---
 drivers/thermal/qcom/qcom-spmi-temp-alarm.c | 140 ++++++++++++++++++++
 1 file changed, 140 insertions(+)

diff --git a/drivers/thermal/qcom/qcom-spmi-temp-alarm.c b/drivers/thermal/qcom/qcom-spmi-temp-alarm.c
index 59a25f02a278..29ec6445fc21 100644
--- a/drivers/thermal/qcom/qcom-spmi-temp-alarm.c
+++ b/drivers/thermal/qcom/qcom-spmi-temp-alarm.c
@@ -26,6 +26,11 @@
 #define QPNP_TM_REG_SHUTDOWN_CTRL1	0x40
 #define QPNP_TM_REG_ALARM_CTRL		0x46
 
+/* TEMP_DAC_STGx registers are only present for TEMP_GEN2 v2.0 */
+#define QPNP_TM_REG_TEMP_DAC_STG1	0x47
+#define QPNP_TM_REG_TEMP_DAC_STG2	0x48
+#define QPNP_TM_REG_TEMP_DAC_STG3	0x49
+
 #define QPNP_TM_TYPE			0x09
 #define QPNP_TM_SUBTYPE_GEN1		0x08
 #define QPNP_TM_SUBTYPE_GEN2		0x09
@@ -65,6 +70,25 @@ static const long temp_map_gen2_v1[THRESH_COUNT][STAGE_COUNT] = {
 
 #define TEMP_STAGE_HYSTERESIS		2000
 
+/*
+ * For TEMP_GEN2 v2.0, TEMP_DAC_STG1/2/3 registers are used to set the threshold
+ * for each stage independently.
+ * TEMP_DAC_STG* = 0 --> 80 C
+ * Each 8 step increase in TEMP_DAC_STG* value corresponds to 5 C (5000 mC).
+ */
+#define TEMP_DAC_MIN			80000
+#define TEMP_DAC_SCALE_NUM		8
+#define TEMP_DAC_SCALE_DEN		5000
+
+#define TEMP_DAC_TEMP_TO_REG(temp) \
+	(((temp) - TEMP_DAC_MIN) * TEMP_DAC_SCALE_NUM / TEMP_DAC_SCALE_DEN)
+#define TEMP_DAC_REG_TO_TEMP(reg) \
+	(TEMP_DAC_MIN + (reg) * TEMP_DAC_SCALE_DEN / TEMP_DAC_SCALE_NUM)
+
+static const long temp_dac_max[STAGE_COUNT] = {
+	119375, 159375, 159375
+};
+
 /* Temperature in Milli Celsius reported during stage 0 if no ADC is present */
 #define DEFAULT_TEMP			37000
 
@@ -73,6 +97,7 @@ struct qpnp_tm_chip;
 struct spmi_temp_alarm_data {
 	const struct thermal_zone_device_ops *ops;
 	const long (*temp_map)[THRESH_COUNT][STAGE_COUNT];
+	int (*setup)(struct qpnp_tm_chip *chip);
 	int (*get_temp_stage)(struct qpnp_tm_chip *chip);
 	int (*configure_trip_temps)(struct qpnp_tm_chip *chip);
 };
@@ -87,6 +112,7 @@ struct qpnp_tm_chip {
 	unsigned int			thresh;
 	unsigned int			stage;
 	unsigned int			base;
+	unsigned int			ntrips;
 	/* protects .thresh, .stage and chip registers */
 	struct mutex			lock;
 	bool				initialized;
@@ -304,6 +330,54 @@ static const struct thermal_zone_device_ops qpnp_tm_sensor_ops = {
 	.set_trip_temp = qpnp_tm_set_trip_temp,
 };
 
+static int qpnp_tm_gen2_rev2_set_temp_thresh(struct qpnp_tm_chip *chip, int trip, int temp)
+{
+	int ret, temp_cfg;
+	u8 reg;
+
+	WARN_ON(!mutex_is_locked(&chip->lock));
+
+	if (trip < 0 || trip >= STAGE_COUNT) {
+		dev_err(chip->dev, "invalid TEMP_DAC trip = %d\n", trip);
+		return -EINVAL;
+	} else if (temp < TEMP_DAC_MIN || temp > temp_dac_max[trip]) {
+		dev_err(chip->dev, "invalid TEMP_DAC temp = %d\n", temp);
+		return -EINVAL;
+	}
+
+	reg = TEMP_DAC_TEMP_TO_REG(temp);
+	temp_cfg = TEMP_DAC_REG_TO_TEMP(reg);
+
+	ret = qpnp_tm_write(chip, QPNP_TM_REG_TEMP_DAC_STG1 + trip, reg);
+	if (ret < 0) {
+		dev_err(chip->dev, "TEMP_DAC_STG write failed, ret=%d\n", ret);
+		return ret;
+	}
+
+	chip->temp_thresh_map[trip] = temp_cfg;
+
+	return 0;
+}
+
+static int qpnp_tm_gen2_rev2_set_trip_temp(struct thermal_zone_device *tz,
+					   const struct thermal_trip *trip, int temp)
+{
+	unsigned int trip_index = THERMAL_TRIP_PRIV_TO_INT(trip->priv);
+	struct qpnp_tm_chip *chip = thermal_zone_device_priv(tz);
+	int ret;
+
+	mutex_lock(&chip->lock);
+	ret = qpnp_tm_gen2_rev2_set_temp_thresh(chip, trip_index, temp);
+	mutex_unlock(&chip->lock);
+
+	return ret;
+}
+
+static const struct thermal_zone_device_ops qpnp_tm_gen2_rev2_sensor_ops = {
+	.get_temp = qpnp_tm_get_temp,
+	.set_trip_temp = qpnp_tm_gen2_rev2_set_trip_temp,
+};
+
 static irqreturn_t qpnp_tm_isr(int irq, void *data)
 {
 	struct qpnp_tm_chip *chip = data;
@@ -328,6 +402,60 @@ static int qpnp_tm_configure_trip_temp(struct qpnp_tm_chip *chip)
 	return ret;
 }
 
+/* Configure TEMP_DAC registers based on DT thermal_zone trips */
+static int qpnp_tm_gen2_rev2_configure_trip_temps_cb(struct thermal_trip *trip, void *data)
+{
+	struct qpnp_tm_chip *chip = data;
+	int ret;
+
+	mutex_lock(&chip->lock);
+	trip->priv = THERMAL_INT_TO_TRIP_PRIV(chip->ntrips);
+	ret = qpnp_tm_gen2_rev2_set_temp_thresh(chip, chip->ntrips, trip->temperature);
+	chip->ntrips++;
+	mutex_unlock(&chip->lock);
+
+	return ret;
+}
+
+static int qpnp_tm_gen2_rev2_configure_trip_temps(struct qpnp_tm_chip *chip)
+{
+	int ret, i;
+
+	ret = thermal_zone_for_each_trip(chip->tz_dev,
+					 qpnp_tm_gen2_rev2_configure_trip_temps_cb, chip);
+	if (ret < 0)
+		return ret;
+
+	/* Verify that trips are strictly increasing. */
+	for (i = 1; i < STAGE_COUNT; i++) {
+		if (chip->temp_thresh_map[i] <= chip->temp_thresh_map[i - 1]) {
+			dev_err(chip->dev, "Threshold %d=%ld <= threshold %d=%ld\n",
+				i, chip->temp_thresh_map[i], i - 1,
+				chip->temp_thresh_map[i - 1]);
+			return -EINVAL;
+		}
+	}
+
+	return 0;
+}
+
+/* Read the hardware default TEMP_DAC stage threshold temperatures */
+static int qpnp_tm_gen2_rev2_setup(struct qpnp_tm_chip *chip)
+{
+	int ret, i;
+	u8 reg = 0;
+
+	for (i = 0; i < STAGE_COUNT; i++) {
+		ret = qpnp_tm_read(chip, QPNP_TM_REG_TEMP_DAC_STG1 + i, &reg);
+		if (ret < 0)
+			return ret;
+
+		chip->temp_thresh_map[i] = TEMP_DAC_REG_TO_TEMP(reg);
+	}
+
+	return 0;
+}
+
 static const struct spmi_temp_alarm_data spmi_temp_alarm_data = {
 	.ops = &qpnp_tm_sensor_ops,
 	.temp_map = &temp_map_gen1,
@@ -349,6 +477,13 @@ static const struct spmi_temp_alarm_data spmi_temp_alarm_gen2_rev1_data = {
 	.get_temp_stage = qpnp_tm_gen2_get_temp_stage,
 };
 
+static const struct spmi_temp_alarm_data spmi_temp_alarm_gen2_rev2_data = {
+	.ops = &qpnp_tm_gen2_rev2_sensor_ops,
+	.setup = qpnp_tm_gen2_rev2_setup,
+	.configure_trip_temps = qpnp_tm_gen2_rev2_configure_trip_temps,
+	.get_temp_stage = qpnp_tm_gen2_get_temp_stage,
+};
+
 /*
  * This function initializes the internal temp value based on only the
  * current thermal stage and threshold. Setup threshold control and
@@ -467,6 +602,8 @@ static int qpnp_tm_probe(struct platform_device *pdev)
 	chip->subtype = subtype;
 	if (subtype == QPNP_TM_SUBTYPE_GEN1)
 		chip->data = &spmi_temp_alarm_data;
+	else if (subtype == QPNP_TM_SUBTYPE_GEN2 && dig_major >= 2)
+		chip->data = &spmi_temp_alarm_gen2_rev2_data;
 	else if (subtype == QPNP_TM_SUBTYPE_GEN2 && dig_major >= 1)
 		chip->data = &spmi_temp_alarm_gen2_rev1_data;
 	else if (subtype == QPNP_TM_SUBTYPE_GEN2)
@@ -491,6 +628,9 @@ static int qpnp_tm_probe(struct platform_device *pdev)
 		}
 	}
 
+	if (chip->data->setup)
+		chip->data->setup(chip);
+
 	/*
 	 * Register the sensor before initializing the hardware to be able to
 	 * read the trip points. get_temp() returns the default temperature
-- 
2.34.1

Re: [PATCH v4 4/5] thermal: qcom-spmi-temp-alarm: add support for GEN2 rev 2 PMIC peripherals

[Bryan O'Donoghue]

On 29/05/2025 00:50, Anjelique Melendez wrote:
> +static int qpnp_tm_gen2_rev2_set_temp_thresh(struct qpnp_tm_chip *chip, int trip, int temp)
> +{
> +	int ret, temp_cfg;
> +	u8 reg;
> +
> +	WARN_ON(!mutex_is_locked(&chip->lock));
> +
> +	if (trip < 0 || trip >= STAGE_COUNT) {

trip < 0 can never be true because the value passed to this function 
comes from an unsigned int

include/linux/thermal.h:#define THERMAL_TRIP_PRIV_TO_INT(_val_) 
(uintptr_t)(_val_)

actually why is it int trip here instead of unsigned int trip ?

> +		dev_err(chip->dev, "invalid TEMP_DAC trip = %d\n", trip);
> +		return -EINVAL;
> +	} else if (temp < TEMP_DAC_MIN || temp > temp_dac_max[trip]) {
> +		dev_err(chip->dev, "invalid TEMP_DAC temp = %d\n", temp);
> +		return -EINVAL;
> +	}
> +
> +	reg = TEMP_DAC_TEMP_TO_REG(temp);
> +	temp_cfg = TEMP_DAC_REG_TO_TEMP(reg);
> +
> +	ret = qpnp_tm_write(chip, QPNP_TM_REG_TEMP_DAC_STG1 + trip, reg);
> +	if (ret < 0) {
> +		dev_err(chip->dev, "TEMP_DAC_STG write failed, ret=%d\n", ret);
> +		return ret;
> +	}
> +
> +	chip->temp_thresh_map[trip] = temp_cfg;
> +
> +	return 0;
> +}
> +
> +static int qpnp_tm_gen2_rev2_set_trip_temp(struct thermal_zone_device *tz,
> +					   const struct thermal_trip *trip, int temp)
> +{
> +	unsigned int trip_index = THERMAL_TRIP_PRIV_TO_INT(trip->priv);
> +	struct qpnp_tm_chip *chip = thermal_zone_device_priv(tz);
> +	int ret;
> +
> +	mutex_lock(&chip->lock);
> +	ret = qpnp_tm_gen2_rev2_set_temp_thresh(chip, trip_index, temp);The sign conversion in the integer seems questionable. I see that the 
intel code does the same thing but I think that's just an error being 
replicated here.
---
bod

[PATCH v4 5/5] thermal: qcom-spmi-temp-alarm: add support for LITE PMIC peripherals

[Anjelique Melendez]

Add support for TEMP_ALARM LITE PMIC peripherals. This subtype
utilizes a pair of registers to configure a warning interrupt
threshold temperature and an automatic hardware shutdown
threshold temperature.

Signed-off-by: David Collins <david.collins@oss.qualcomm.com>
Signed-off-by: Anjelique Melendez <anjelique.melendez@oss.qualcomm.com>
---
 drivers/thermal/qcom/qcom-spmi-temp-alarm.c | 208 +++++++++++++++++++-
 1 file changed, 207 insertions(+), 1 deletion(-)

diff --git a/drivers/thermal/qcom/qcom-spmi-temp-alarm.c b/drivers/thermal/qcom/qcom-spmi-temp-alarm.c
index 29ec6445fc21..1dcbc4415db3 100644
--- a/drivers/thermal/qcom/qcom-spmi-temp-alarm.c
+++ b/drivers/thermal/qcom/qcom-spmi-temp-alarm.c
@@ -23,6 +23,7 @@
 #define QPNP_TM_REG_TYPE		0x04
 #define QPNP_TM_REG_SUBTYPE		0x05
 #define QPNP_TM_REG_STATUS		0x08
+#define QPNP_TM_REG_IRQ_STATUS		0x10
 #define QPNP_TM_REG_SHUTDOWN_CTRL1	0x40
 #define QPNP_TM_REG_ALARM_CTRL		0x46
 
@@ -30,14 +31,20 @@
 #define QPNP_TM_REG_TEMP_DAC_STG1	0x47
 #define QPNP_TM_REG_TEMP_DAC_STG2	0x48
 #define QPNP_TM_REG_TEMP_DAC_STG3	0x49
+#define QPNP_TM_REG_LITE_TEMP_CFG1	0x50
+#define QPNP_TM_REG_LITE_TEMP_CFG2	0x51
 
 #define QPNP_TM_TYPE			0x09
 #define QPNP_TM_SUBTYPE_GEN1		0x08
 #define QPNP_TM_SUBTYPE_GEN2		0x09
+#define QPNP_TM_SUBTYPE_LITE		0xC0
 
 #define STATUS_GEN1_STAGE_MASK		GENMASK(1, 0)
 #define STATUS_GEN2_STATE_MASK		GENMASK(6, 4)
 
+/* IRQ status only needed for TEMP_ALARM_LITE */
+#define IRQ_STATUS_MASK			BIT(0)
+
 #define SHUTDOWN_CTRL1_OVERRIDE_S2	BIT(6)
 #define SHUTDOWN_CTRL1_THRESHOLD_MASK	GENMASK(1, 0)
 
@@ -45,6 +52,8 @@
 
 #define ALARM_CTRL_FORCE_ENABLE		BIT(7)
 
+#define LITE_TEMP_CFG_THRESHOLD_MASK	GENMASK(3, 2)
+
 #define THRESH_COUNT			4
 #define STAGE_COUNT			3
 
@@ -89,6 +98,19 @@ static const long temp_dac_max[STAGE_COUNT] = {
 	119375, 159375, 159375
 };
 
+/*
+ * TEMP_ALARM_LITE has two stages: warning and shutdown with independently
+ * configured threshold temperatures.
+ */
+
+static const long temp_lite_warning_map[THRESH_COUNT] = {
+	115000, 125000, 135000, 145000
+};
+
+static const long temp_lite_shutdown_map[THRESH_COUNT] = {
+	135000, 145000, 160000, 175000
+};
+
 /* Temperature in Milli Celsius reported during stage 0 if no ADC is present */
 #define DEFAULT_TEMP			37000
 
@@ -197,6 +219,24 @@ static int qpnp_tm_gen2_get_temp_stage(struct qpnp_tm_chip *chip)
 	return alarm_state_map[ret];
 }
 
+/**
+ * qpnp_tm_lite_get_temp_stage() - return over-temperature stage
+ * @chip:		Pointer to the qpnp_tm chip
+ *
+ * Return: alarm interrupt state on success, or errno on failure.
+ */
+static int qpnp_tm_lite_get_temp_stage(struct qpnp_tm_chip *chip)
+{
+	u8 reg = 0;
+	int ret;
+
+	ret = qpnp_tm_read(chip, QPNP_TM_REG_IRQ_STATUS, &reg);
+	if (ret < 0)
+		return ret;
+
+	return reg & IRQ_STATUS_MASK;
+}
+
 /*
  * This function updates the internal temp value based on the
  * current thermal stage and threshold as well as the previous stage
@@ -378,6 +418,98 @@ static const struct thermal_zone_device_ops qpnp_tm_gen2_rev2_sensor_ops = {
 	.set_trip_temp = qpnp_tm_gen2_rev2_set_trip_temp,
 };
 
+static int qpnp_tm_lite_set_temp_thresh(struct qpnp_tm_chip *chip, int trip, int temp)
+{
+	int ret, temp_cfg, i;
+	const long *temp_map;
+	u16 addr;
+	u8 reg, thresh;
+
+	WARN_ON(!mutex_is_locked(&chip->lock));
+
+	if (trip < 0 || trip >= STAGE_COUNT) {
+		dev_err(chip->dev, "invalid TEMP_LITE trip = %d\n", trip);
+		return -EINVAL;
+	}
+
+	switch (trip) {
+	case 0:
+		temp_map = temp_lite_warning_map;
+		addr = QPNP_TM_REG_LITE_TEMP_CFG1;
+		break;
+	case 1:
+		/*
+		 * The second trip point is purely in software to facilitate
+		 * a controlled shutdown after the warning threshold is crossed
+		 * but before the automatic hardware shutdown threshold is
+		 * crossed.
+		 */
+		return 0;
+	case 2:
+		temp_map = temp_lite_shutdown_map;
+		addr = QPNP_TM_REG_LITE_TEMP_CFG2;
+		break;
+	default:
+		return 0;
+	}
+
+	if (temp < temp_map[THRESH_MIN] || temp > temp_map[THRESH_MAX]) {
+		dev_err(chip->dev, "invalid TEMP_LITE temp = %d\n", temp);
+		return -EINVAL;
+	}
+
+	thresh = 0;
+	temp_cfg = temp_map[thresh];
+	for (i = THRESH_MAX; i >= THRESH_MIN; i--) {
+		if (temp >= temp_map[i]) {
+			thresh = i;
+			temp_cfg = temp_map[i];
+			break;
+		}
+	}
+
+	if (temp_cfg == chip->temp_thresh_map[trip])
+		return 0;
+
+	ret = qpnp_tm_read(chip, addr, &reg);
+	if (ret < 0) {
+		dev_err(chip->dev, "LITE_TEMP_CFG read failed, ret=%d\n", ret);
+		return ret;
+	}
+
+	reg &= ~LITE_TEMP_CFG_THRESHOLD_MASK;
+	reg |= FIELD_PREP(LITE_TEMP_CFG_THRESHOLD_MASK, thresh);
+
+	ret = qpnp_tm_write(chip, addr, reg);
+	if (ret < 0) {
+		dev_err(chip->dev, "LITE_TEMP_CFG write failed, ret=%d\n", ret);
+		return ret;
+	}
+
+	chip->temp_thresh_map[trip] = temp_cfg;
+
+	return 0;
+}
+
+static int qpnp_tm_lite_set_trip_temp(struct thermal_zone_device *tz,
+				      const struct thermal_trip *trip, int temp)
+{
+	unsigned int trip_index = THERMAL_TRIP_PRIV_TO_INT(trip->priv);
+	struct qpnp_tm_chip *chip = thermal_zone_device_priv(tz);
+	int ret;
+
+	mutex_lock(&chip->lock);
+	ret = qpnp_tm_lite_set_temp_thresh(chip, trip_index, temp);
+	mutex_unlock(&chip->lock);
+
+	return ret;
+}
+
+static const struct thermal_zone_device_ops qpnp_tm_lite_sensor_ops = {
+	.get_temp = qpnp_tm_get_temp,
+	.set_trip_temp = qpnp_tm_lite_set_trip_temp,
+};
+
 static irqreturn_t qpnp_tm_isr(int irq, void *data)
 {
 	struct qpnp_tm_chip *chip = data;
@@ -456,6 +588,70 @@ static int qpnp_tm_gen2_rev2_setup(struct qpnp_tm_chip *chip)
 	return 0;
 }
 
+/* Configure TEMP_LITE registers based on DT thermal_zone trips */
+static int qpnp_tm_lite_configure_trip_temps_cb(struct thermal_trip *trip, void *data)
+{
+	struct qpnp_tm_chip *chip = data;
+	int ret;
+
+	mutex_lock(&chip->lock);
+	trip->priv = THERMAL_INT_TO_TRIP_PRIV(chip->ntrips);
+	ret = qpnp_tm_lite_set_temp_thresh(chip, chip->ntrips, trip->temperature);
+	chip->ntrips++;
+	mutex_unlock(&chip->lock);
+
+	return ret;
+}
+
+static int qpnp_tm_lite_configure_trip_temps(struct qpnp_tm_chip *chip)
+{
+	int ret;
+
+	ret = thermal_zone_for_each_trip(chip->tz_dev, qpnp_tm_lite_configure_trip_temps_cb, chip);
+	if (ret < 0)
+		return ret;
+
+	/* Verify that trips are strictly increasing. */
+	if (chip->temp_thresh_map[2] <= chip->temp_thresh_map[0]) {
+		dev_err(chip->dev, "Threshold 2=%ld <= threshold 0=%ld\n",
+			chip->temp_thresh_map[2], chip->temp_thresh_map[0]);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+/* Read the hardware default TEMP_LITE stage threshold temperatures */
+static int qpnp_tm_lite_setup(struct qpnp_tm_chip *chip)
+{
+	int ret, thresh;
+	u8 reg = 0;
+
+	/*
+	 * Store the warning trip temp in temp_thresh_map[0] and the shutdown trip
+	 * temp in temp_thresh_map[2].  The second trip point is purely in software
+	 * to facilitate a controlled shutdown after the warning threshold is
+	 * crossed but before the automatic hardware shutdown threshold is
+	 * crossed.  Thus, there is no register to read for the second trip
+	 * point.
+	 */
+	ret = qpnp_tm_read(chip, QPNP_TM_REG_LITE_TEMP_CFG1, &reg);
+	if (ret < 0)
+		return ret;
+
+	thresh = FIELD_GET(LITE_TEMP_CFG_THRESHOLD_MASK, reg);
+	chip->temp_thresh_map[0] = temp_lite_warning_map[thresh];
+
+	ret = qpnp_tm_read(chip, QPNP_TM_REG_LITE_TEMP_CFG2, &reg);
+	if (ret < 0)
+		return ret;
+
+	thresh = FIELD_GET(LITE_TEMP_CFG_THRESHOLD_MASK, reg);
+	chip->temp_thresh_map[2] = temp_lite_shutdown_map[thresh];
+
+	return 0;
+}
+
 static const struct spmi_temp_alarm_data spmi_temp_alarm_data = {
 	.ops = &qpnp_tm_sensor_ops,
 	.temp_map = &temp_map_gen1,
@@ -484,6 +680,13 @@ static const struct spmi_temp_alarm_data spmi_temp_alarm_gen2_rev2_data = {
 	.get_temp_stage = qpnp_tm_gen2_get_temp_stage,
 };
 
+static const struct spmi_temp_alarm_data spmi_temp_alarm_lite_data = {
+	.ops = &qpnp_tm_lite_sensor_ops,
+	.setup = qpnp_tm_lite_setup,
+	.configure_trip_temps = qpnp_tm_lite_configure_trip_temps,
+	.get_temp_stage = qpnp_tm_lite_get_temp_stage,
+};
+
 /*
  * This function initializes the internal temp value based on only the
  * current thermal stage and threshold. Setup threshold control and
@@ -593,7 +796,8 @@ static int qpnp_tm_probe(struct platform_device *pdev)
 	}
 
 	if (type != QPNP_TM_TYPE || (subtype != QPNP_TM_SUBTYPE_GEN1
-				     && subtype != QPNP_TM_SUBTYPE_GEN2)) {
+				     && subtype != QPNP_TM_SUBTYPE_GEN2
+				     && subtype != QPNP_TM_SUBTYPE_LITE)) {
 		dev_err(&pdev->dev, "invalid type 0x%02x or subtype 0x%02x\n",
 			type, subtype);
 		return -ENODEV;
@@ -608,6 +812,8 @@ static int qpnp_tm_probe(struct platform_device *pdev)
 		chip->data = &spmi_temp_alarm_gen2_rev1_data;
 	else if (subtype == QPNP_TM_SUBTYPE_GEN2)
 		chip->data = &spmi_temp_alarm_gen2_data;
+	else if (subtype == QPNP_TM_SUBTYPE_LITE)
+		chip->data = &spmi_temp_alarm_lite_data;
 	else
 		return -ENODEV;
 
-- 
2.34.1

Re: [PATCH v4 5/5] thermal: qcom-spmi-temp-alarm: add support for LITE PMIC peripherals

[Dmitry Baryshkov]

On Wed, May 28, 2025 at 04:50:26PM -0700, Anjelique Melendez wrote:
> Add support for TEMP_ALARM LITE PMIC peripherals. This subtype
> utilizes a pair of registers to configure a warning interrupt
> threshold temperature and an automatic hardware shutdown
> threshold temperature.
> 
> Signed-off-by: David Collins <david.collins@oss.qualcomm.com>
> Signed-off-by: Anjelique Melendez <anjelique.melendez@oss.qualcomm.com>
> ---
>  drivers/thermal/qcom/qcom-spmi-temp-alarm.c | 208 +++++++++++++++++++-
>  1 file changed, 207 insertions(+), 1 deletion(-)
> 

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>

-- 
With best wishes
Dmitry