[PATCH v2 0/6] arm64: dts: qcom: talos-lyra-evk: Add display overlays for EVK board

[PATCH v2 0/6] arm64: dts: qcom: talos-lyra-evk: Add display overlays for EVK board

[anand.tiwari]

Talos Lyra EVK SoC card are mounted on the Lyra carrier card. The
DSI0 interface from SoC card is routed to either the 22-pin DSI
connector on carrier card named as JDISP1 DSI0 or to the DSI0_B2B
connector, through a MUX which can be selected by a hardware DIP
switch. There are multiple daughter cards designed that can be
connected to this B2B connector.

The below B2B display interfaces are enabled by default in base DTB:
  - DSI-to-HDMI using the LT9611UXD daughter card

Below overlay DTs are added for additional display configurations:
  - talos-lyra-evk-dlc0697: DLC0697 DSI panel for Lyra with DLC
    daughter card
  - talos-lyra-evk-raspberrypi-dsi-7inch: Raspberry Pi 7-inch DSI
    panel with touch via the 22-pin DSI connector for Lyra
  - talos-lyra-evk-waveshare-dsi-8inch: Waveshare 8-inch DSI panel
    with touch via the 22-pin DSI connector for Lyra
  - talos-lyra-evk-lvds-auo,g133han01: AUO G133HAN01 LVDS panel for
    Lyra with LVDS daughter card

These overlays are applied on top of the corresponding base board
DTBs.

Link: https://lore.kernel.org/r/20261012-talos-lyra-evk-v2-v2-0-dcc9316ebb59@oss.qualcomm.com
Signed-off-by: Anand Tiwari <anand.tiwari@oss.qualcomm.com>
---
Changes in v2:
- Fold in the hdmi_connector port remote-endpoint indentation fix.
- Drop the per-patch Depends-on trailer on the LT9611UXD HDMI bridge
  patch; the dt-bindings dependency is now declared as a series
  prerequisite (see base-commit/prerequisite info below).
- Drop default-on from the DLC0697 backlight node.
- Add the ilitek,ili9881c fallback compatible to the RPi 7-inch
  panel overlay to fix a dtbs_check "too short" binding failure.
- Reword the PWM_CLK defconfig commit message to name Qualcomm as
  the SoC vendor.
- Remove a stray blank line and non-ASCII characters from the AUO
  LVDS panel overlay.
- Link to v1: https://patch.msgid.link/20261021-lyra-display-upstream-post-v1-0-585caa39cd7c@oss.qualcomm.com

To: Bjorn Andersson <andersson@kernel.org>
To: Konrad Dybcio <konradybcio@kernel.org>
To: Abel Vesa <abelvesa@kernel.org>
To: Rob Herring <robh@kernel.org>
To: Krzysztof Kozlowski <krzk+dt@kernel.org>
To: Conor Dooley <conor+dt@kernel.org>
To: Florian Fainelli <florian.fainelli@broadcom.com>
To: Broadcom internal kernel review list <bcm-kernel-feedback-list@broadcom.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org

---
Anand Tiwari (2):
      arm64: defconfig: Enable PWM_CLK for backlight PWM support
      arm64: dts: qcom: talos-lyra-evk: Add AUO G133HAN01 LVDS panel overlay

Mohit Dsor (1):
      arm64: dts: qcom: talos-lyra-evk: Add LT9611UXD HDMI bridge support

Shashank Maurya (3):
      arm64: dts: qcom: talos-lyra-evk: Add DLC DLC0697 panel overlay
      arm64: dts: qcom: talos-lyra-evk: Add RPi 7-inch DSI panel overlay
      arm64: dts: qcom: talos-lyra-evk: Add Waveshare 8-inch DSI panel overlay

 arch/arm64/boot/dts/qcom/Makefile                  |  18 +++
 .../boot/dts/qcom/talos-lyra-evk-dlc0697.dtso      |  77 ++++++++++++
 .../qcom/talos-lyra-evk-lvds-auo,g133han01.dtso    | 133 +++++++++++++++++++++
 .../qcom/talos-lyra-evk-raspberrypi-dsi-7inch.dtso |  88 ++++++++++++++
 .../qcom/talos-lyra-evk-waveshare-dsi-8inch.dtso   |  75 ++++++++++++
 arch/arm64/boot/dts/qcom/talos-lyra-evk.dts        | 106 ++++++++++++++++
 arch/arm64/configs/defconfig                       |   1 +
 7 files changed, 498 insertions(+)
---
base-commit: 4eb2586bd40db27d77cc5b724ca9386ed0c71d53
change-id: 20261019-lyra-display-upstream-post-24656268a902
prerequisite-message-id: <20261027-talos-lyra-evk-v2-v3-0-658fd5a7ec99@oss.qualcomm.com>
prerequisite-patch-id: 0dfae1e9d0c620866489eecacb4b7201b9333621
prerequisite-patch-id: 94923ba8f57911649364a7e0e5494c7cfd478367
prerequisite-patch-id: 660755293839baa7364b4baf3a2dd6b4018de48a
prerequisite-message-id: <20261021-lt9611c-v7-v18-0-4978b94896f1@oss.qualcomm.com>
prerequisite-patch-id: 49f1e01bb5594ce9c4301ce4b16715834ece7f41
prerequisite-patch-id: 21cfbbfd71515961501a768edad476740336c13c

Best regards,
--  
Anand Tiwari <anand.tiwari@oss.qualcomm.com>

[PATCH v2 1/6] arm64: dts: qcom: talos-lyra-evk: Add LT9611UXD HDMI bridge support

[anand.tiwari]

From: Mohit Dsor <mohit.dsor@oss.qualcomm.com>

Add support for the Lontium LT9611UXD DSI-to-HDMI bridge, enabled by
default on the Talos Lyra EVK base board DT, to provide HDMI output
on the DSI0_B2B connector on the carrier card.

LT9611UXD is connected through I2C2, with reset and interrupt
connected to TLMM GPIO61 and GPIO60 respectively.

Signed-off-by: Mohit Dsor <mohit.dsor@oss.qualcomm.com>
Signed-off-by: Anand Tiwari <anand.tiwari@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/talos-lyra-evk.dts | 105 ++++++++++++++++++++++++++++
 1 file changed, 105 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/talos-lyra-evk.dts b/arch/arm64/boot/dts/qcom/talos-lyra-evk.dts
index d4468e609911..eeb8e903b03b 100644
--- a/arch/arm64/boot/dts/qcom/talos-lyra-evk.dts
+++ b/arch/arm64/boot/dts/qcom/talos-lyra-evk.dts
@@ -4,6 +4,8 @@
  */
 /dts-v1/;
 
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 #include "talos-lyra-evk-som.dtsi"
 
 / {
@@ -11,6 +13,10 @@ / {
 	compatible = "qcom,talos-lyra-evk", "qcom,qcs615", "qcom,sm6150";
 	chassis-type = "embedded";
 
+	aliases {
+		i2c2 = &i2c2;
+	};
+
 	dp0-connector {
 		compatible = "dp-connector";
 		label = "DP0";
@@ -22,6 +28,65 @@ dp0_connector_in: endpoint {
 			};
 		};
 	};
+
+	hdmi_connector: hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_out: endpoint {
+				remote-endpoint = <&hdmi_bridge_out>;
+			};
+		};
+	};
+
+	vreg_disp_3p3: regulator-disp-3p3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_disp_3p3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&tlmm 3 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-0 = <&lcd_bias_en>;
+		pinctrl-names = "default";
+	};
+};
+
+&i2c2 {
+	status = "okay";
+
+	hdmi_bridge: hdmi-bridge@41 {
+		compatible = "lontium,lt9611uxd";
+		reg = <0x41>;
+		interrupts-extended = <&tlmm 60 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&tlmm 61 GPIO_ACTIVE_LOW>;
+		vcc-supply = <&vreg_disp_3p3>;
+		vdd-supply = <&vreg_s4a>;
+
+		pinctrl-0 = <&bridge_irq_pin &bridge_rst_pin>;
+		pinctrl-names = "default";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				hdmi_bridge_in: endpoint {
+					remote-endpoint = <&mdss_dsi0_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				hdmi_bridge_out: endpoint {
+					remote-endpoint = <&hdmi_connector_out>;
+				};
+			};
+		};
+	};
 };
 
 &i2c5 {
@@ -74,6 +139,23 @@ &mdss_dp0_out {
 	remote-endpoint = <&dp0_connector_in>;
 };
 
+&mdss_dsi0 {
+	vdda-supply = <&vreg_l5a>;
+
+	status = "okay";
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&hdmi_bridge_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+	vdds-supply = <&vreg_l11a>;
+
+	status = "okay";
+};
+
 &pon_pwrkey {
 	status = "okay";
 };
@@ -113,3 +195,26 @@ &usb_2 {
 
 	status = "okay";
 };
+
+&tlmm {
+	lcd_bias_en: lcd-bias-en-state {
+		pins = "gpio3";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	bridge_irq_pin: bridge-irq-state {
+		pins = "gpio60";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	bridge_rst_pin: bridge-rst-state {
+		pins = "gpio61";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+};

-- 
2.55.0

[PATCH v2 2/6] arm64: dts: qcom: talos-lyra-evk: Add DLC DLC0697 panel overlay

[anand.tiwari]

From: Shashank Maurya <shashank.maurya@oss.qualcomm.com>

Add a DT overlay for Qualcomm Talos Lyra EVK, to enable DLC0697 panel
when DLC daughter card connected to DSI0_B2B on carrier card.

Configure DLC0697 reset GPIO, supplies, pinctrl states and GPIO
backlight controlled through TLMM GPIO 2.

Disable the default HDMI bridge and connector in favour of the DSI
panel.

Signed-off-by: Shashank Maurya <shashank.maurya@oss.qualcomm.com>
Signed-off-by: Anand Tiwari <anand.tiwari@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/Makefile                  |  4 ++
 .../boot/dts/qcom/talos-lyra-evk-dlc0697.dtso      | 77 ++++++++++++++++++++++
 2 files changed, 81 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 243231692866..709a96ece14e 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -476,6 +476,10 @@ dtb-$(CONFIG_ARCH_QCOM)	+= talos-lyra-evk.dtb
 talos-lyra-evk-el2-dtbs	:= talos-lyra-evk.dtb talos-el2.dtbo
 
 dtb-$(CONFIG_ARCH_QCOM)	+= talos-lyra-evk-el2.dtb
+
+talos-lyra-evk-dlc0697-dtbs := talos-lyra-evk.dtb talos-lyra-evk-dlc0697.dtbo
+dtb-$(CONFIG_ARCH_QCOM)     += talos-lyra-evk-dlc0697.dtb
+dtb-$(CONFIG_ARCH_QCOM)     += talos-lyra-evk-dlc0697.dtbo
 x1e001de-devkit-el2-dtbs	:= x1e001de-devkit.dtb x1-el2.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e001de-devkit.dtb x1e001de-devkit-el2.dtb
 x1e78100-lenovo-thinkpad-t14s-el2-dtbs	:= x1e78100-lenovo-thinkpad-t14s.dtb x1-el2.dtbo
diff --git a/arch/arm64/boot/dts/qcom/talos-lyra-evk-dlc0697.dtso b/arch/arm64/boot/dts/qcom/talos-lyra-evk-dlc0697.dtso
new file mode 100644
index 000000000000..b79e54459725
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/talos-lyra-evk-dlc0697.dtso
@@ -0,0 +1,77 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+&{/} {
+	backlight: backlight {
+		compatible = "gpio-backlight";
+		gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&hdmi_bridge {
+	status = "disabled";
+};
+
+&hdmi_connector {
+	status = "disabled";
+};
+
+&mdss_dsi0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	panel@0 {
+		compatible = "dlc,dlc0697", "ilitek,ili7807s";
+		reg = <0>;
+
+		reset-gpios = <&tlmm 118 GPIO_ACTIVE_LOW>;
+		backlight = <&backlight>;
+
+		vddi-supply = <&vreg_s4a>;
+		avdd-supply = <&vreg_disp_3p3>;
+		avee-supply = <&vreg_disp_3p3>;
+
+		pinctrl-0 = <&panel_rst_n &panel_te_pin>;
+		pinctrl-1 = <&panel_rst_n_suspend>;
+		pinctrl-names = "default", "sleep";
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&mdss_dsi0_out>;
+			};
+		};
+	};
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&panel_in>;
+};
+
+&tlmm {
+	panel_te_pin: panel-te-pin-state {
+		pins = "gpio98";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	panel_rst_n: panel-rst-n-state {
+		pins = "gpio118";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	panel_rst_n_suspend: panel-rst-n-suspend-state {
+		pins = "gpio118";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+};

-- 
2.55.0

[PATCH v2 3/6] arm64: dts: qcom: talos-lyra-evk: Add RPi 7-inch DSI panel overlay

[anand.tiwari]

From: Shashank Maurya <shashank.maurya@oss.qualcomm.com>

Add a DT overlay to enable Raspberry Pi 7-inch DSI panel connected
to DSI 22pin on the carrier card.

DSI0 from SOC is routed through MUX which can be selected by DIP
switch S1016.5 ON for enabling this 22pin connector.

Add the regulator and backlight controller at I2C2 address 0x45,
Goodix GT911 touch controller, panel power and reset control, and
a 2-lane DSI connection.

Disable the default HDMI bridge and connector in favour of the RPi
DSI panel.

Signed-off-by: Shashank Maurya <shashank.maurya@oss.qualcomm.com>
Signed-off-by: Anand Tiwari <anand.tiwari@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/Makefile                  |  5 ++
 .../qcom/talos-lyra-evk-raspberrypi-dsi-7inch.dtso | 88 ++++++++++++++++++++++
 2 files changed, 93 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 709a96ece14e..298054f47046 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -480,6 +480,11 @@ dtb-$(CONFIG_ARCH_QCOM)	+= talos-lyra-evk-el2.dtb
 talos-lyra-evk-dlc0697-dtbs := talos-lyra-evk.dtb talos-lyra-evk-dlc0697.dtbo
 dtb-$(CONFIG_ARCH_QCOM)     += talos-lyra-evk-dlc0697.dtb
 dtb-$(CONFIG_ARCH_QCOM)     += talos-lyra-evk-dlc0697.dtbo
+
+talos-lyra-evk-raspberrypi-dsi-7inch-dtbs := \
+        talos-lyra-evk.dtb talos-lyra-evk-raspberrypi-dsi-7inch.dtbo
+dtb-$(CONFIG_ARCH_QCOM) += talos-lyra-evk-raspberrypi-dsi-7inch.dtb
+dtb-$(CONFIG_ARCH_QCOM) += talos-lyra-evk-raspberrypi-dsi-7inch.dtbo
 x1e001de-devkit-el2-dtbs	:= x1e001de-devkit.dtb x1-el2.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e001de-devkit.dtb x1e001de-devkit-el2.dtb
 x1e78100-lenovo-thinkpad-t14s-el2-dtbs	:= x1e78100-lenovo-thinkpad-t14s.dtb x1-el2.dtbo
diff --git a/arch/arm64/boot/dts/qcom/talos-lyra-evk-raspberrypi-dsi-7inch.dtso b/arch/arm64/boot/dts/qcom/talos-lyra-evk-raspberrypi-dsi-7inch.dtso
new file mode 100644
index 000000000000..6dafdbb87d3d
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/talos-lyra-evk-raspberrypi-dsi-7inch.dtso
@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+&{/} {
+	display_bl: backlight {
+		compatible = "pwm-backlight";
+		power-supply = <&reg_display>;
+		pwms = <&mcu 0 255 0>;
+	};
+
+	reg_display: regulator-display {
+		compatible = "regulator-fixed";
+		regulator-name = "rpi-display";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_dsi_touch: regulator-dsi-touch {
+		compatible = "regulator-fixed";
+		gpio = <&mcu 1 GPIO_ACTIVE_HIGH>;
+		regulator-name = "rpi-touch";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <50000>;
+		enable-active-high;
+	};
+};
+
+&hdmi_bridge {
+	status = "disabled";
+};
+
+&hdmi_connector {
+	status = "disabled";
+};
+
+&i2c2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	mcu: gpio@45 {
+		compatible = "raspberrypi,touchscreen-panel-regulator-v2";
+		reg = <0x45>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		#pwm-cells = <3>;
+	};
+
+	touchscreen@5d {
+		compatible = "goodix,gt911";
+		reg = <0x5d>;
+		AVDD28-supply = <&reg_dsi_touch>;
+		touchscreen-size-x = <720>;
+		touchscreen-size-y = <1280>;
+	};
+};
+
+&mdss_dsi0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	panel@0 {
+		compatible = "raspberrypi,dsi-7inch", "ilitek,ili9881c";
+		reg = <0>;
+
+		reset-gpios = <&mcu 0 GPIO_ACTIVE_LOW>;
+		power-supply = <&reg_display>;
+		iovcc-supply = <&vreg_s4a>;
+		backlight = <&display_bl>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&mdss_dsi0_out>;
+			};
+		};
+	};
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&panel_in>;
+	data-lanes = <0 1>;
+};

-- 
2.55.0

[PATCH v2 4/6] arm64: dts: qcom: talos-lyra-evk: Add Waveshare 8-inch DSI panel overlay

[anand.tiwari]

From: Shashank Maurya <shashank.maurya@oss.qualcomm.com>

Add a DT overlay to enable Waveshare 8-inch DSI panel connected to
DSI 22pin on the carrier card.

DSI0 from SOC is routed through MUX which can be selected by DIP
switch S1016.5 ON, for enabling this 22pin connector.

Add the JD9365DA-H3 panel, GPIO expander at I2C2 address 0x45 for
panel power, reset and backlight, and the Goodix GT9271 touch
controller.

Disable the default HDMI bridge and connector in favour of the
Waveshare DSI panel.

Signed-off-by: Shashank Maurya <shashank.maurya@oss.qualcomm.com>
Signed-off-by: Anand Tiwari <anand.tiwari@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/Makefile                  |  5 ++
 .../qcom/talos-lyra-evk-waveshare-dsi-8inch.dtso   | 75 ++++++++++++++++++++++
 2 files changed, 80 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 298054f47046..b6a61339914d 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -485,6 +485,11 @@ talos-lyra-evk-raspberrypi-dsi-7inch-dtbs := \
         talos-lyra-evk.dtb talos-lyra-evk-raspberrypi-dsi-7inch.dtbo
 dtb-$(CONFIG_ARCH_QCOM) += talos-lyra-evk-raspberrypi-dsi-7inch.dtb
 dtb-$(CONFIG_ARCH_QCOM) += talos-lyra-evk-raspberrypi-dsi-7inch.dtbo
+
+talos-lyra-evk-waveshare-dsi-8inch-dtbs := \
+        talos-lyra-evk.dtb talos-lyra-evk-waveshare-dsi-8inch.dtbo
+dtb-$(CONFIG_ARCH_QCOM) += talos-lyra-evk-waveshare-dsi-8inch.dtb
+dtb-$(CONFIG_ARCH_QCOM) += talos-lyra-evk-waveshare-dsi-8inch.dtbo
 x1e001de-devkit-el2-dtbs	:= x1e001de-devkit.dtb x1-el2.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e001de-devkit.dtb x1e001de-devkit-el2.dtb
 x1e78100-lenovo-thinkpad-t14s-el2-dtbs	:= x1e78100-lenovo-thinkpad-t14s.dtb x1-el2.dtbo
diff --git a/arch/arm64/boot/dts/qcom/talos-lyra-evk-waveshare-dsi-8inch.dtso b/arch/arm64/boot/dts/qcom/talos-lyra-evk-waveshare-dsi-8inch.dtso
new file mode 100644
index 000000000000..e9a8fdf0c179
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/talos-lyra-evk-waveshare-dsi-8inch.dtso
@@ -0,0 +1,75 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+&{/} {
+	panel_avdd: regulator-panel-avdd {
+		compatible = "regulator-fixed";
+		regulator-name = "panel-avdd";
+		gpios = <&wsgpio 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	panel_iovcc: regulator-panel-iovcc {
+		compatible = "regulator-fixed";
+		regulator-name = "panel-iovcc";
+		gpios = <&wsgpio 4 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&hdmi_bridge {
+	status = "disabled";
+};
+
+&hdmi_connector {
+	status = "disabled";
+};
+
+&i2c2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	wsgpio: gpio@45 {
+		compatible = "waveshare,dsi-touch-gpio";
+		reg = <0x45>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	touchscreen@5d {
+		compatible = "goodix,gt9271";
+		reg = <0x5d>;
+		reset-gpios = <&wsgpio 9 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&mdss_dsi0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	panel@0 {
+		compatible = "waveshare,8.0-dsi-touch-a", "jadard,jd9365da-h3";
+		reg = <0>;
+
+		reset-gpios = <&wsgpio 1 GPIO_ACTIVE_LOW>;
+		vccio-supply = <&panel_iovcc>;
+		vdd-supply = <&panel_avdd>;
+		backlight = <&wsgpio>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&mdss_dsi0_out>;
+			};
+		};
+	};
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&panel_in>;
+};

-- 
2.55.0

[PATCH v2 5/6] arm64: defconfig: Enable PWM_CLK for backlight PWM support

[Anand Tiwari]

Enable CONFIG_PWM_CLK so the generic clock-based PWM driver is
available, used by the Qualcomm Talos Lyra EVK LVDS panel overlay
backlight.

Signed-off-by: Anand Tiwari <anand.tiwari@oss.qualcomm.com>
---
 arch/arm64/configs/defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 50d6357727af..365a69470d13 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -1620,6 +1620,7 @@ CONFIG_PWM_ADP5585=m
 CONFIG_PWM_APPLE=m
 CONFIG_PWM_BCM2835=m
 CONFIG_PWM_BRCMSTB=m
+CONFIG_PWM_CLK=m
 CONFIG_PWM_CROS_EC=m
 CONFIG_PWM_IMX27=m
 CONFIG_PWM_MEDIATEK=m

-- 
2.55.0

[PATCH v2 6/6] arm64: dts: qcom: talos-lyra-evk: Add AUO G133HAN01 LVDS panel overlay

[Anand Tiwari]

Add a DT overlay for Qualcomm Talos Lyra EVK, to enable LVDS interface
when LVDS daughter card is connected to DSI0_B2B on carrier card.

There is SN65DSI84 DSI-to-LVDS bridge on the daughter card which is
connected through I2C5 with reset and interrupt connected to
GPIO61 and GPIO60. Backlight is driven by a generic clock-based PWM
using GCC_GP3 on TLMM GPIO59, with an additional backlight enable
GPIO on TLMM GPIO2.

Disable the default HDMI bridge and connector in favour of the LVDS
panel.

Signed-off-by: Anand Tiwari <anand.tiwari@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/Makefile                  |   4 +
 .../qcom/talos-lyra-evk-lvds-auo,g133han01.dtso    | 133 +++++++++++++++++++++
 arch/arm64/boot/dts/qcom/talos-lyra-evk.dts        |   1 +
 3 files changed, 138 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index b6a61339914d..012dee96f700 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -468,6 +468,10 @@ dtb-$(CONFIG_ARCH_QCOM)	+= talos-evk-camera-imx577.dtb
 talos-evk-lvds-auo,g133han01-dtbs	:= \
 	talos-evk.dtb talos-evk-lvds-auo,g133han01.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= talos-evk-lvds-auo,g133han01.dtb
+talos-lyra-evk-lvds-auo,g133han01-dtbs := \
+	talos-lyra-evk.dtb talos-lyra-evk-lvds-auo,g133han01.dtbo
+dtb-$(CONFIG_ARCH_QCOM) += talos-lyra-evk-lvds-auo,g133han01.dtb
+dtb-$(CONFIG_ARCH_QCOM) += talos-lyra-evk-lvds-auo,g133han01.dtbo
 talos-evk-rpi-display-2-5in-dtbs	:= \
 	talos-evk.dtb talos-evk-rpi-display-2-5in.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= talos-evk-rpi-display-2-5in.dtb
diff --git a/arch/arm64/boot/dts/qcom/talos-lyra-evk-lvds-auo,g133han01.dtso b/arch/arm64/boot/dts/qcom/talos-lyra-evk-lvds-auo,g133han01.dtso
new file mode 100644
index 000000000000..8c592e6317c3
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/talos-lyra-evk-lvds-auo,g133han01.dtso
@@ -0,0 +1,133 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/clock/qcom,qcs615-gcc.h>
+#include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+&{/} {
+	bklt_pwm: pwm {
+		compatible = "clk-pwm";
+		#pwm-cells = <2>;
+		assigned-clock-parents = <&rpmhcc RPMH_CXO_CLK>;
+		assigned-clocks = <&gcc GCC_GP3_CLK_SRC>;
+		clocks = <&gcc GCC_GP3_CLK>;
+		pinctrl-0 = <&bklt_pwm_default>;
+		pinctrl-names = "default";
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&bklt_pwm 0 100000>;
+		power-supply = <&vreg_disp_3p3>;
+		enable-gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+		brightness-levels = <0 255>;
+		num-interpolated-steps = <255>;
+		default-brightness-level = <128>;
+	};
+
+	panel-lvds {
+		compatible = "auo,g133han01";
+		power-supply = <&vreg_disp_3p3>;
+		backlight = <&backlight>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/* LVDS Channel A - odd pixels */
+			port@0 {
+				reg = <0>;
+				dual-lvds-odd-pixels;
+
+				lvds_panel_out_a: endpoint {
+					remote-endpoint = <&sn65dsi84_out_a>;
+				};
+			};
+
+			/* LVDS Channel B - even pixels */
+			port@1 {
+				reg = <1>;
+				dual-lvds-even-pixels;
+
+				lvds_panel_out_b: endpoint {
+					remote-endpoint = <&sn65dsi84_out_b>;
+				};
+			};
+		};
+	};
+};
+
+&hdmi_connector {
+	status = "disabled";
+};
+
+&i2c5 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bridge@2c {
+		compatible = "ti,sn65dsi84";
+		reg = <0x2c>;
+		enable-gpios = <&tlmm 61 GPIO_ACTIVE_HIGH>;
+		interrupts-extended = <&tlmm 60 IRQ_TYPE_EDGE_FALLING>;
+		vcc-supply = <&vreg_s4a>;
+
+		pinctrl-0 = <&bridge_irq_pin &bridge_rst_pin>;
+		pinctrl-names = "default";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				sn65dsi84_in: endpoint {
+					remote-endpoint = <&mdss_dsi0_out>;
+					data-lanes = <1 2 3 4>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				sn65dsi84_out_a: endpoint {
+					data-lanes = <1 2 3 4>;
+					remote-endpoint = <&lvds_panel_out_a>;
+				};
+			};
+
+			port@3 {
+				reg = <3>;
+
+				sn65dsi84_out_b: endpoint {
+					data-lanes = <1 2 3 4>;
+					remote-endpoint = <&lvds_panel_out_b>;
+				};
+			};
+		};
+	};
+};
+
+&hdmi_bridge {
+	status = "disabled";
+};
+
+&tlmm {
+	bklt_pwm_default: bklt-pwm-default-state {
+		pins = "gpio59";
+		function = "gcc_gp";
+	};
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&sn65dsi84_in>;
+	data-lanes = <0 1 2 3>;
+};
diff --git a/arch/arm64/boot/dts/qcom/talos-lyra-evk.dts b/arch/arm64/boot/dts/qcom/talos-lyra-evk.dts
index eeb8e903b03b..e5c2ea9e1e07 100644
--- a/arch/arm64/boot/dts/qcom/talos-lyra-evk.dts
+++ b/arch/arm64/boot/dts/qcom/talos-lyra-evk.dts
@@ -15,6 +15,7 @@ / {
 
 	aliases {
 		i2c2 = &i2c2;
+		i2c5 = &i2c5;
 	};
 
 	dp0-connector {

-- 
2.55.0

Re: [PATCH v2 5/6] arm64: defconfig: Enable PWM_CLK for backlight PWM support

[Krzysztof Kozlowski]

On 30/10/2026 10:40, Anand Tiwari wrote:
> Enable CONFIG_PWM_CLK so the generic clock-based PWM driver is
> available, used by the Qualcomm Talos Lyra EVK LVDS panel overlay
> backlight.
> 
> Signed-off-by: Anand Tiwari <anand.tiwari@oss.qualcomm.com>
> ---
>  arch/arm64/configs/defconfig | 1 +
>  1 file changed, 1 insertion(+)

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>

Best regards,
Krzysztof