2.6.28: hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...

2.6.28: hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...

[Justin Piszcz]

[-- Attachment #1: Type: TEXT/PLAIN, Size: 3655 bytes --]

The audio for this board works fine, there are no issues, but there are 
some cosmetic issues when the driver loads:

1. Unknown model.
2. Wrong model number.

On my ABIT AW9D-MAX motherboard:
[   10.667963] Advanced Linux Sound Architecture Driver Version 1.0.18rc3.
[   10.668156] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 1
6
[   10.668228] HDA Intel 0000:00:1b.0: setting latency timer to 64
[   10.677932] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS.
..
[   10.705082] ALSA device list:
[   10.705128]   #0: HDA Intel at 0xfdff8000 irq 16

On an Intel motherboard, correctly detected, no warnings about an Unknown
model.

[    5.466951] Advanced Linux Sound Architecture Driver Version 1.0.18rc3.
[    5.470149] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[    5.473135] HDA Intel 0000:00:1b.0: setting latency timer to 64
[    5.512645] ALSA device list:
[    5.515568]   #0: HDA Intel at 0xe2420000 irq 22

Specs:
# abit AudioMAX# HD 7.1 CH
# Supports Jack Sensing and S/PDIF In/Out
# Dolby® Master Studio Certificated 
http://www.abit.com.tw/page/en/motherboard/motherboard_detail.php?pMODEL_NAME=AW9D-MAX&fMTYPE=LGA775&pPRODINFO=Specifications&fSEARCHTEXT=AW9D-MAX

Not too specific, however:
http://www.anandtech.com/mb/showdoc.aspx?i=2829

Reveals the correct model:
-> Realtek ALC882M HD-Audio 8-channel CODEC - Dolby Master Studio 
Where the kernel believes it is an ALC883.

Would it be possible to probe properly/and get the correct model number in 
there for this audio chipset?

lspci:
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01)

lspci -vvvx:
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01)
   Subsystem: ABIT Computer Corp. Device 107a
   Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0, Cache Line Size: 4 bytes
   Interrupt: pin A routed to IRQ 16
   Region 0: Memory at fdff8000 (64-bit, non-prefetchable) [size=16K]
   Capabilities: [50] Power Management version 2
     Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
     Status: D0 PME-Enable- DSel=0 DScale=0 PME-
   Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
     Address: 0000000000000000  Data: 0000
   Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
     DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
       ExtTag- RBE- FLReset-
     DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
       RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
       MaxPayload 128 bytes, MaxReadReq 128 bytes
     DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
     LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
       ClockPM- Suprise- LLActRep- BwNot-
     LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
       ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
     LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
   Capabilities: [100] Virtual Channel <?>
   Capabilities: [130] Root Complex Link <?>
   Kernel driver in use: HDA Intel
00: 86 80 d8 27 06 00 10 00 01 00 03 04 01 00 00 00
10: 04 80 ff fd 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 7a 10
30: 00 00 00 00 50 00 00 00 00 00 00 00 05 01 00 00

Re: 2.6.28: hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...

[Justin Piszcz]

[-- Attachment #1: Type: TEXT/PLAIN, Size: 3882 bytes --]



On Tue, 30 Dec 2008, Justin Piszcz wrote:

> The audio for this board works fine, there are no issues, but there are some 
> cosmetic issues when the driver loads:
>
> 1. Unknown model.
> 2. Wrong model number.
>
> On my ABIT AW9D-MAX motherboard:
> [   10.667963] Advanced Linux Sound Architecture Driver Version 1.0.18rc3.
> [   10.668156] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> 
> IRQ 1
> 6
> [   10.668228] HDA Intel 0000:00:1b.0: setting latency timer to 64
> [   10.677932] hda_codec: Unknown model for ALC883, trying auto-probe from 
> BIOS.
> ..
> [   10.705082] ALSA device list:
> [   10.705128]   #0: HDA Intel at 0xfdff8000 irq 16
>
> On an Intel motherboard, correctly detected, no warnings about an Unknown
> model.
>
> [    5.466951] Advanced Linux Sound Architecture Driver Version 1.0.18rc3.
> [    5.470149] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> 
> IRQ 22
> [    5.473135] HDA Intel 0000:00:1b.0: setting latency timer to 64
> [    5.512645] ALSA device list:
> [    5.515568]   #0: HDA Intel at 0xe2420000 irq 22
>
> Specs:
> # abit AudioMAX# HD 7.1 CH
> # Supports Jack Sensing and S/PDIF In/Out
> # Dolby® Master Studio Certificated 
> http://www.abit.com.tw/page/en/motherboard/motherboard_detail.php?pMODEL_NAME=AW9D-MAX&fMTYPE=LGA775&pPRODINFO=Specifications&fSEARCHTEXT=AW9D-MAX
>
> Not too specific, however:
> http://www.anandtech.com/mb/showdoc.aspx?i=2829
>
> Reveals the correct model:
> -> Realtek ALC882M HD-Audio 8-channel CODEC - Dolby Master Studio Where the 
> kernel believes it is an ALC883.
>
> Would it be possible to probe properly/and get the correct model number in 
> there for this audio chipset?
>
> lspci:
> 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition 
> Audio Controller (rev 01)
>
> lspci -vvvx:
> 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition 
> Audio Controller (rev 01)
>  Subsystem: ABIT Computer Corp. Device 107a
>  Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
> Stepping- SERR- FastB2B- DisINTx-
>  Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
> <MAbort- >SERR- <PERR- INTx-
>  Latency: 0, Cache Line Size: 4 bytes
>  Interrupt: pin A routed to IRQ 16
>  Region 0: Memory at fdff8000 (64-bit, non-prefetchable) [size=16K]
>  Capabilities: [50] Power Management version 2
>    Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA 
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
>    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>  Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 
> Enable-
>    Address: 0000000000000000  Data: 0000
>  Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
>    DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
>      ExtTag- RBE- FLReset-
>    DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
>      RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
>      MaxPayload 128 bytes, MaxReadReq 128 bytes
>    DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
>    LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, 
> L1 <1us
>      ClockPM- Suprise- LLActRep- BwNot-
>    LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
>      ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
>    LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- 
> ABWMgmt-
>  Capabilities: [100] Virtual Channel <?>
>  Capabilities: [130] Root Complex Link <?>
>  Kernel driver in use: HDA Intel
> 00: 86 80 d8 27 06 00 10 00 01 00 03 04 01 00 00 00
> 10: 04 80 ff fd 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 7a 10
> 30: 00 00 00 00 50 00 00 00 00 00 00 00 05 01 00 00

Fixed alsa e-mail in cc list.

Justin.

Re: 2.6.28: hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...

[Justin Piszcz]

[-- Attachment #1: Type: TEXT/PLAIN, Size: 1868 bytes --]



On Tue, 30 Dec 2008, Justin Piszcz wrote:

>
>
> On Tue, 30 Dec 2008, Justin Piszcz wrote:
>
>> The audio for this board works fine, there are no issues, but there are 
>> some cosmetic issues when the driver loads:
>> 
>> 1. Unknown model.
>> 2. Wrong model number.
>> 
>> On my ABIT AW9D-MAX motherboard:
>> [   10.667963] Advanced Linux Sound Architecture Driver Version 1.0.18rc3.
>> [   10.668156] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> 
>> IRQ 1
>> 6
>> [   10.668228] HDA Intel 0000:00:1b.0: setting latency timer to 64
>> [   10.677932] hda_codec: Unknown model for ALC883, trying auto-probe from 
>> BIOS.
>> ..
>> [   10.705082] ALSA device list:
>> [   10.705128]   #0: HDA Intel at 0xfdff8000 irq 16
>> 
>> On an Intel motherboard, correctly detected, no warnings about an Unknown
>> model.
>> 
>> [    5.466951] Advanced Linux Sound Architecture Driver Version 1.0.18rc3.
>> [    5.470149] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> 
>> IRQ 22
>> [    5.473135] HDA Intel 0000:00:1b.0: setting latency timer to 64
>> [    5.512645] ALSA device list:
>> [    5.515568]   #0: HDA Intel at 0xe2420000 irq 22
>> 
>> Specs:
>> # abit AudioMAX# HD 7.1 CH
>> # Supports Jack Sensing and S/PDIF In/Out
>> # Dolby® Master Studio Certificated 
>> http://www.abit.com.tw/page/en/motherboard/motherboard_detail.php?pMODEL_NAME=AW9D-MAX&fMTYPE=LGA775&pPRODINFO=Specifications&fSEARCHTEXT=AW9D-MAX
>> 
>> Not too specific, however:
>> http://www.anandtech.com/mb/showdoc.aspx?i=2829
>> 
>> Reveals the correct model:
>> -> Realtek ALC882M HD-Audio 8-channel CODEC - Dolby Master Studio Where the 
>> kernel believes it is an ALC883.
>>

This would need to be fixed in the kernel.. yes? I had been asked to run
update-pciids but afaik that only affects lspci output.

Justin.

Re: 2.6.28: hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...

[Takashi Iwai]

At Tue, 30 Dec 2008 07:28:14 -0500 (EST),
Justin Piszcz wrote:
> 
> On Tue, 30 Dec 2008, Justin Piszcz wrote:
> 
> > The audio for this board works fine, there are no issues, but there are some 
> > cosmetic issues when the driver loads:
> >
> > 1. Unknown model.

It's no bug.
It's neither warning nor error message but a information message.

> > 2. Wrong model number.

They likely share the same ID and compatible.
So don't worry about it.

In short, nothing to fix, so far.


thanks,

Takashi