[PATCH v3 0/7] display: lcdif: imx: add display support for imx8dxl and imx8qxp

[PATCH v3 0/7] display: lcdif: imx: add display support for imx8dxl and imx8qxp

[Frank.Li]

i.MX8DXL and i.MX8QX support LCDIF, which is compatible with i.MX6SX.

- Update lcdif binding doc to support front compatible string:
fsl,imxqxp-lcdif and fsl,imx8dxl-lcdif
- Update simple pannel binding doc and driver to support waiken,101wx001
- update chip dts to support lcdif ip
- add overlay file to enable lcd panel waiken,101wx001 and lcdif
- use onboard pinmux "pinctrl-multiplexer" for on board signal switch

Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
Changes in v3:
- add bus-width = <18>
- add lcd panel information at dtb file.
- detail see each patch's change log
- Link to v2: https://patch.msgid.link/20260715-dxl_lcdif-v2-0-da797562636e@nxp.com

Changes in v2 (fix sashiko reported problem):
- add power domain required for binding
- fix 136 height
- add acm patch to cleam MCL clock output pin
- remove iomux hog in overlay file
- Link to v1: https://patch.msgid.link/20260714-dxl_lcdif-v1-0-6761a8a6592b@nxp.com

---
Frank Li (7):
      dt-bindings: lcdif: add compatible string for i.MX8QXP and i.MX8DXL
      dt-bindings: display: simple: Add waiken,101wx001-wct
      drm/panel: simple: Add Waiken WKS101WX001-WCT panel support
      arm64: dts: imx8-ss-dma: Add lcdif support for i.MX8QXP and i.MX8DXL
      arm64: dts: imx8dxl-evk: Add onboard GPIO mux controller
      arm64: dts: imx8dxl-evk: Move ACM MCLK pin to ACM pinctrl
      arm64: dts: imx8dxl-evk: add lcdif overlay

 .../devicetree/bindings/display/fsl,lcdif.yaml     |   6 ++
 .../bindings/display/panel/panel-simple.yaml       |   2 +
 .../devicetree/bindings/vendor-prefixes.yaml       |   2 +
 arch/arm64/boot/dts/freescale/Makefile             |   3 +
 arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi     |  29 +++++
 .../dts/freescale/imx8dxl-evk-lcdif-101wx001.dtso  | 119 +++++++++++++++++++++
 arch/arm64/boot/dts/freescale/imx8dxl-evk.dts      |  88 ++++++++++++---
 arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi |  11 ++
 drivers/gpu/drm/panel/panel-simple.c               |  31 ++++++
 9 files changed, 279 insertions(+), 12 deletions(-)
---
base-commit: c27e4587a73de339f2d9f1304c913413055ed408
change-id: 20260709-dxl_lcdif-d6cbdbac92fb

Best regards,
--  
Frank Li <Frank.Li@nxp.com>

[PATCH v3 1/7] dt-bindings: lcdif: add compatible string for i.MX8QXP and i.MX8DXL

[Frank.Li]

From: Frank Li <Frank.Li@nxp.com>

i.MX8QXP and i.MX8DXL have lcdif, which back compatible with i.MX6SX. Add
front compatible string "fsl,imx8dxl-lcdif" and "fsl,imx8qxp-lcdif", which
fallback to "fsl,imx6sx-lcdif".

Required power-domains for both. Required 3 clocks and clock-names.

Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
change in v3
- require 3 clocks ans clock-names
change in v2
- require power-domains (sashiko)
---
 Documentation/devicetree/bindings/display/fsl,lcdif.yaml | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/fsl,lcdif.yaml b/Documentation/devicetree/bindings/display/fsl,lcdif.yaml
index 5f56e733c4f7f..c986ac87fc2bf 100644
--- a/Documentation/devicetree/bindings/display/fsl,lcdif.yaml
+++ b/Documentation/devicetree/bindings/display/fsl,lcdif.yaml
@@ -28,9 +28,11 @@ properties:
               - fsl,imx6sll-lcdif
               - fsl,imx6ul-lcdif
               - fsl,imx7d-lcdif
+              - fsl,imx8dxl-lcdif
               - fsl,imx8mm-lcdif
               - fsl,imx8mn-lcdif
               - fsl,imx8mq-lcdif
+              - fsl,imx8qxp-lcdif
           - const: fsl,imx6sx-lcdif
 
   reg:
@@ -122,7 +124,9 @@ allOf:
         compatible:
           contains:
             enum:
+              - fsl,imx8dxl-lcdif
               - fsl,imx8mp-lcdif
+              - fsl,imx8qxp-lcdif
               - fsl,imx93-lcdif
     then:
       properties:
@@ -162,9 +166,11 @@ allOf:
           contains:
             enum:
               - fsl,imx6sl-lcdif
+              - fsl,imx8dxl-lcdif
               - fsl,imx8mm-lcdif
               - fsl,imx8mn-lcdif
               - fsl,imx8mp-lcdif
+              - fsl,imx8qxp-lcdif
               - fsl,imx93-lcdif
     then:
       required:

-- 
2.43.0

Re: [PATCH v3 1/7] dt-bindings: lcdif: add compatible string for i.MX8QXP and i.MX8DXL

[Liu Ying]

On Tue, Oct 20, 2026 at 04:12:51PM -0400, Frank.Li@oss.nxp.com wrote:
> From: Frank Li <Frank.Li@nxp.com>
> 
> i.MX8QXP and i.MX8DXL have lcdif, which back compatible with i.MX6SX. Add
> front compatible string "fsl,imx8dxl-lcdif" and "fsl,imx8qxp-lcdif", which
> fallback to "fsl,imx6sx-lcdif".
> 
> Required power-domains for both. Required 3 clocks and clock-names.
> 
> Signed-off-by: Frank Li <Frank.Li@nxp.com>
> ---
> change in v3
> - require 3 clocks ans clock-names
> change in v2
> - require power-domains (sashiko)
> ---
>  Documentation/devicetree/bindings/display/fsl,lcdif.yaml | 6 ++++++
>  1 file changed, 6 insertions(+)

Acked-by: Liu Ying <victor.liu@nxp.com>

[PATCH v3 2/7] dt-bindings: display: simple: Add waiken,101wx001-wct

[Frank.Li]

From: Frank Li <Frank.Li@nxp.com>

Add WKS101WX001-WCT panel, which is an industrial-grade 10.1-inch IPS TFT
LCD capacitive touch screen display module.

Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
change in v3
- Use Waiken Technology Limited in description
- Use 10.1" at comments
- Use waiken,101wx001-wct
---
 Documentation/devicetree/bindings/display/panel/panel-simple.yaml | 2 ++
 Documentation/devicetree/bindings/vendor-prefixes.yaml            | 2 ++
 2 files changed, 4 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
index eb49832b26c46..15f7dc0d0f6d5 100644
--- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
+++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
@@ -353,6 +353,8 @@ properties:
       - vivax,tpc9150-panel
         # VXT 800x480 color TFT LCD panel
       - vxt,vl050-8048nt-c01
+        # Waiken 10.1" IPS TFT LCD panel with capacitive touch
+      - waiken,101wx001-wct
         # Waveshare 10.1" WXGA (1280x800) LCD panel
       - waveshare,10.1inch-c-panel
         # Waveshare 11.9" (320x1480) LCD panel
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 473019dd01263..97d77d1759e39 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -1885,6 +1885,8 @@ patternProperties:
     description: VXT Ltd
   "^wacom,.*":
     description: Wacom
+  "^waiken,.*":
+    description: Waiken Technology Limited
   "^wanchanglong,.*":
     description: Wanchanglong Electronics Technology（SHENZHEN）Co.，Ltd.
   "^wand,.*":

-- 
2.43.0

Re: [PATCH v3 2/7] dt-bindings: display: simple: Add waiken,101wx001-wct

[Liu Ying]

On Tue, Oct 20, 2026 at 04:12:52PM -0400, Frank.Li@oss.nxp.com wrote:
> From: Frank Li <Frank.Li@nxp.com>
> 
> Add WKS101WX001-WCT panel, which is an industrial-grade 10.1-inch IPS TFT
> LCD capacitive touch screen display module.
> 
> Signed-off-by: Frank Li <Frank.Li@nxp.com>
> ---
> change in v3
> - Use Waiken Technology Limited in description
> - Use 10.1" at comments
> - Use waiken,101wx001-wct
> ---
>  Documentation/devicetree/bindings/display/panel/panel-simple.yaml | 2 ++
>  Documentation/devicetree/bindings/vendor-prefixes.yaml            | 2 ++
>  2 files changed, 4 insertions(+)

Acked-by: Liu Ying <victor.liu@nxp.com>

[PATCH v3 3/7] drm/panel: simple: Add Waiken WKS101WX001-WCT panel support

[Frank.Li]

From: Frank Li <Frank.Li@nxp.com>

Add support for the Waiken WKS101WX001-WCT, an industrial-grade 10.1-inch
IPS TFT LCD panel with a capacitive touchscreen.

Although the module advertises LVDS support, enabling LVDS operation
requires hardware modification, including the removal of several on-board
resistors. As there are currently no known users of the LVDS configuration,
only the default interface mode is supported.

If LVDS support is needed in the future, a dedicated driver can be
introduced to handle switching between LVDS and LDB modes.

Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
change in v3
- add wct surfix and change to use MEDIA_BUS_FMT_RGB888_1X24
- Add information about lvds support plan.

change in v2
- update height to 135 from 136 (sashiko)
---
 drivers/gpu/drm/panel/panel-simple.c | 31 +++++++++++++++++++++++++++++++
 1 file changed, 31 insertions(+)

diff --git a/drivers/gpu/drm/panel/panel-simple.c b/drivers/gpu/drm/panel/panel-simple.c
index d7dbd7442919b..f2a1668087de7 100644
--- a/drivers/gpu/drm/panel/panel-simple.c
+++ b/drivers/gpu/drm/panel/panel-simple.c
@@ -5252,6 +5252,34 @@ static const struct panel_desc vl050_8048nt_c01 = {
 	.bus_flags = DRM_BUS_FLAG_DE_HIGH | DRM_BUS_FLAG_PIXDATA_SAMPLE_NEGEDGE,
 };
 
+static const struct drm_display_mode waiken_101wx001_mode = {
+	.clock = 71100,
+	.hdisplay = 1280,
+	.hsync_start = 1280 + 70,
+	.hsync_end = 1280 + 70 + 10,
+	.htotal = 1280 + 70 + 10 + 80,
+	.vdisplay = 800,
+	.vsync_start = 800 + 10,
+	.vsync_end = 800 + 10 + 3,
+	.vtotal = 800 + 10 + 3 + 10,
+	.width_mm = 217,
+	.height_mm = 135,
+	.flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
+};
+
+static const struct panel_desc waiken_101wx001_panel = {
+	.modes = &waiken_101wx001_mode,
+	.num_modes = 1,
+	.bpc = 8,
+	.size = {
+		.width = 217,
+		.height = 135,
+	},
+	.bus_format = MEDIA_BUS_FMT_RGB888_1X24,
+	.connector_type = DRM_MODE_CONNECTOR_DPI,
+	.bus_flags = DRM_BUS_FLAG_DE_HIGH | DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE,
+};
+
 static const struct drm_display_mode waveshare_28_lcd_mode = {
 	.clock = 50000,
 	.hdisplay = 480,
@@ -6248,6 +6276,9 @@ static const struct of_device_id platform_of_match[] = {
 	}, {
 		.compatible = "vxt,vl050-8048nt-c01",
 		.data = &vl050_8048nt_c01,
+	}, {
+		.compatible = "waiken,101wx001-wct",
+		.data = &waiken_101wx001_panel,
 	}, {
 		.compatible = "waveshare,2.8inch-panel",
 		.data = &waveshare_28_lcd_panel

-- 
2.43.0

Re: [PATCH v3 3/7] drm/panel: simple: Add Waiken WKS101WX001-WCT panel support

[Liu Ying]

On Tue, Oct 20, 2026 at 04:12:53PM -0400, Frank.Li@oss.nxp.com wrote:
> From: Frank Li <Frank.Li@nxp.com>
> 
> Add support for the Waiken WKS101WX001-WCT, an industrial-grade 10.1-inch
> IPS TFT LCD panel with a capacitive touchscreen.
> 
> Although the module advertises LVDS support, enabling LVDS operation
> requires hardware modification, including the removal of several on-board
> resistors. As there are currently no known users of the LVDS configuration,
> only the default interface mode is supported.
> 
> If LVDS support is needed in the future, a dedicated driver can be
> introduced to handle switching between LVDS and LDB modes.

s/LDB/DPI/ ?

> 
> Signed-off-by: Frank Li <Frank.Li@nxp.com>
> ---
> change in v3
> - add wct surfix and change to use MEDIA_BUS_FMT_RGB888_1X24
> - Add information about lvds support plan.
> 
> change in v2
> - update height to 135 from 136 (sashiko)
> ---
>  drivers/gpu/drm/panel/panel-simple.c | 31 +++++++++++++++++++++++++++++++
>  1 file changed, 31 insertions(+)
> 
> diff --git a/drivers/gpu/drm/panel/panel-simple.c b/drivers/gpu/drm/panel/panel-simple.c
> index d7dbd7442919b..f2a1668087de7 100644
> --- a/drivers/gpu/drm/panel/panel-simple.c
> +++ b/drivers/gpu/drm/panel/panel-simple.c
> @@ -5252,6 +5252,34 @@ static const struct panel_desc vl050_8048nt_c01 = {
>  	.bus_flags = DRM_BUS_FLAG_DE_HIGH | DRM_BUS_FLAG_PIXDATA_SAMPLE_NEGEDGE,
>  };
>  
> +static const struct drm_display_mode waiken_101wx001_mode = {

To align with the compatible string:
s/101wx001/101wx001_WCT/

> +	.clock = 71100,
> +	.hdisplay = 1280,
> +	.hsync_start = 1280 + 70,
> +	.hsync_end = 1280 + 70 + 10,
> +	.htotal = 1280 + 70 + 10 + 80,
> +	.vdisplay = 800,
> +	.vsync_start = 800 + 10,
> +	.vsync_end = 800 + 10 + 3,
> +	.vtotal = 800 + 10 + 3 + 10,
> +	.width_mm = 217,
> +	.height_mm = 135,
> +	.flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
> +};
> +
> +static const struct panel_desc waiken_101wx001_panel = {

Ditto.

-- 
Regards,
Liu Ying

[PATCH v3 4/7] arm64: dts: imx8-ss-dma: Add lcdif support for i.MX8QXP and i.MX8DXL

[Frank.Li]

From: Frank Li <Frank.Li@nxp.com>

Add lcdif support for i.MX8QXP and i.MX8DXL.

Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
 arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi     | 29 ++++++++++++++++++++++
 arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi | 11 ++++++++
 2 files changed, 40 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi
index 4de78f870c05c..87082c3fa9338 100644
--- a/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi
@@ -149,6 +149,24 @@ lpuart3: serial@5a090000 {
 		status = "disabled";
 	};
 
+	adma_lcdif: lcdif@5a180000 {
+		compatible = "fsl,imx8qxp-lcdif", "fsl,imx6sx-lcdif";
+		reg = <0x5a180000 0x10000>;
+		clocks = <&lcd_clk_lpcg IMX_LPCG_CLK_0>,
+			 <&lcd_clk_lpcg IMX_LPCG_CLK_4>,
+			 <&clk IMX_SC_R_LCD_0 IMX_SC_PM_CLK_MISC0>;
+		clock-names = "pix", "axi", "disp_axi";
+		assigned-clocks = <&clk IMX_SC_R_LCD_0 IMX_SC_PM_CLK_PER>,
+				  <&clk IMX_SC_R_LCD_0 IMX_SC_PM_CLK_MISC0>,
+				  <&clk IMX_SC_R_ELCDIF_PLL IMX_SC_PM_CLK_PLL>;
+		assigned-clock-parents = <&clk IMX_SC_R_ELCDIF_PLL IMX_SC_PM_CLK_PLL>,
+					 <&clk IMX_SC_R_LCD_0 IMX_SC_PM_CLK_BYPASS>;
+		assigned-clock-rates = <0>, <24000000>, <804000000>;
+		interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&pd IMX_SC_R_LCD_0>;
+		status = "disabled";
+	};
+
 	adma_pwm: pwm@5a190000 {
 		compatible = "fsl,imx8qxp-pwm", "fsl,imx27-pwm";
 		reg = <0x5a190000 0x1000>;
@@ -298,6 +316,17 @@ uart3_lpcg: clock-controller@5a490000 {
 		power-domains = <&pd IMX_SC_R_UART_3>;
 	};
 
+	lcd_clk_lpcg: clock-controller@5a580000 {
+		compatible = "fsl,imx8qxp-lpcg";
+		reg = <0x5a580000 0x4>;
+		#clock-cells = <1>;
+		clocks = <&clk IMX_SC_R_LCD_0 IMX_SC_PM_CLK_PER>,
+			 <&dma_ipg_clk>;
+		clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>;
+		clock-output-names = "lcd_clk_lpcg", "lcd_ipg_clk";
+		power-domains = <&pd IMX_SC_R_LCD_0>;
+	};
+
 	adma_pwm_lpcg: clock-controller@5a590000 {
 		compatible = "fsl,imx8qxp-lpcg";
 		reg = <0x5a590000 0x10000>;
diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi
index 7a191195dbd97..febf5f8b54ac4 100644
--- a/arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi
@@ -60,6 +60,17 @@ &acm {
 		      "sai3_rx_bclk";
 };
 
+&adma_lcdif {
+	compatible = "fsl,imx8dxl-lcdif", "fsl,imx6sx-lcdif";
+	assigned-clocks = <&clk IMX_SC_R_LCD_0 IMX_SC_PM_CLK_PER>,
+			  <&clk IMX_SC_R_LCD_0 IMX_SC_PM_CLK_MISC0>,
+			  <&clk IMX_SC_R_ELCDIF_PLL IMX_SC_PM_CLK_PLL>;
+	assigned-clock-parents = <&clk IMX_SC_R_ELCDIF_PLL IMX_SC_PM_CLK_PLL>,
+				 <&clk IMX_SC_R_LCD_0 IMX_SC_PM_CLK_BYPASS>;
+	assigned-clock-rates = <0>, <24000000>, <711000000>;
+	interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+};
+
 &audio_ipg_clk {
 	clock-frequency = <160000000>;
 };

-- 
2.43.0

[PATCH v3 5/7] arm64: dts: imx8dxl-evk: Add onboard GPIO mux controller

[Frank.Li]

From: Frank Li <Frank.Li@nxp.com>

Add a GPIO mux controller to describe the onboard signal multiplexer.
Previously, the device tree relied on the hardware reset defaults to
select the mux state. Now that the kernel supports the pinctrl-multiplexer
framework, describe the onboard mux explicitly and let the kernel configure
the required routing.

Prepare for additional device tree overlays that require different mux
configurations.

Remove the regulator-m2uart1sel node, which incorrectly modeled the board
mux as a regulator.

There are no backward compatibility concerns, as the affected functions
(lpuart1 for Bluetooth, spi3, and m4_lpuart) are not used by existing other
users such as U-Boot.

Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
 arch/arm64/boot/dts/freescale/imx8dxl-evk.dts | 76 +++++++++++++++++++++++----
 1 file changed, 65 insertions(+), 11 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts b/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts
index 71eff3efa6d32..312e4ef3a6760 100644
--- a/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts
@@ -97,14 +97,68 @@ vdev0buffer: vdev0buffer@90400000 {
 		};
 	};
 
-	m2_uart1_sel: regulator-m2uart1sel {
-		compatible = "regulator-fixed";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-name = "m2_uart1_sel";
-		gpio = <&pca6416_1 6 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-		regulator-always-on;
+	m4_debug_mux: mux-controller-0 {
+		compatible = "gpio-mux";
+		#mux-control-cells = <0>;
+		#mux-state-cells = <1>;
+		mux-gpios = <&pca6416_1 3 GPIO_ACTIVE_HIGH>;
+	};
+
+	spi3_mux: mux-controller-1 {
+		compatible = "gpio-mux";
+		#mux-control-cells = <0>;
+		#mux-state-cells = <1>;
+		mux-gpios = <&pca6416_1 4 GPIO_ACTIVE_HIGH>;
+	};
+
+	uart1_mux: mux-controller-2 {
+		compatible = "gpio-mux";
+		#mux-control-cells = <0>;
+		#mux-state-cells = <1>;
+		mux-gpios = <&pca6416_1 6 GPIO_ACTIVE_HIGH>;
+	};
+
+	spi0_mux: mux-controller-3 {
+		compatible = "gpio-mux";
+		#mux-control-cells = <0>;
+		#mux-state-cells = <1>;
+		mux-gpios = <&pca6416_1 7 GPIO_ACTIVE_HIGH>;
+	};
+
+	pinctrl-gpiomux {
+		compatible = "pinctrl-multiplexer";
+
+		m4_debug_fun: cm4-uart-grp {
+			mux-states = <&m4_debug_mux 1>;
+		};
+
+		spi0_fun: spi0-grp {
+			mux-states = <&spi0_mux 1>;
+		};
+
+		spi3_fun: spi3-grp {
+			mux-states = <&spi3_mux 1>;
+		};
+
+		uart1_fun: uart1-grp {
+			mux-states = <&uart1_mux 1>;
+		};
+
+		lcd_0_fun: lcd0-grp {
+			mux-states = <&spi0_mux 0>;
+		};
+
+		lcd_1_fun: lcd1-grp {
+			mux-states = <&spi3_mux 0>;
+		};
+
+		lcd_2_fun: lcd2-grp {
+			mux-states = <&uart1_mux 0>;
+		};
+
+		lcd_3_fun: lcd3-grp {
+			mux-states = <&m4_debug_mux 0>;
+		};
 	};
 
 	mux3_en: regulator-0 {
@@ -620,7 +674,7 @@ &lpuart0 {
 
 &lpuart1 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_lpuart1>;
+	pinctrl-0 = <&pinctrl_lpuart1>, <&uart1_fun>;
 	status = "okay";
 
 	bluetooth {
@@ -658,7 +712,7 @@ &cm40_intmux {
 
 &cm40_lpuart {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_cm40_lpuart>;
+	pinctrl-0 = <&pinctrl_cm40_lpuart>, <&m4_debug_fun>;
 	status = "disabled";
 };
 
@@ -879,7 +933,7 @@ &usdhc2 {
 &lpspi3 {
 	fsl,spi-only-use-cs1-sel;
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_lpspi3>;
+	pinctrl-0 = <&pinctrl_lpspi3>, <&spi3_fun>;
 	status = "okay";
 };
 

-- 
2.43.0

Re: [PATCH v3 5/7] arm64: dts: imx8dxl-evk: Add onboard GPIO mux controller

[Liu Ying]

On Tue, Oct 20, 2026 at 04:12:55PM -0400, Frank.Li@oss.nxp.com wrote:

[...]

> +	pinctrl-gpiomux {
> +		compatible = "pinctrl-multiplexer";
> +
> +		m4_debug_fun: cm4-uart-grp {
> +			mux-states = <&m4_debug_mux 1>;
> +		};
> +
> +		spi0_fun: spi0-grp {
> +			mux-states = <&spi0_mux 1>;
> +		};
> +
> +		spi3_fun: spi3-grp {
> +			mux-states = <&spi3_mux 1>;
> +		};
> +
> +		uart1_fun: uart1-grp {
> +			mux-states = <&uart1_mux 1>;
> +		};
> +
> +		lcd_0_fun: lcd0-grp {
> +			mux-states = <&spi0_mux 0>;
> +		};
> +
> +		lcd_1_fun: lcd1-grp {
> +			mux-states = <&spi3_mux 0>;
> +		};
> +
> +		lcd_2_fun: lcd2-grp {
> +			mux-states = <&uart1_mux 0>;
> +		};
> +
> +		lcd_3_fun: lcd3-grp {
> +			mux-states = <&m4_debug_mux 0>;
> +		};

Nit: Can you sort the child node names alphabetically?

>  	};

-- 
Regards,
Liu Ying

[PATCH v3 6/7] arm64: dts: imx8dxl-evk: Move ACM MCLK pin to ACM pinctrl

[Frank.Li]

From: Frank Li <Frank.Li@nxp.com>

Move the IMX8DXL_SPI3_CS0_ADMA_ACM_MCLK_OUT1 pin from the iomuxc hog
group to the ACM pinctrl state.

The pin is used as the ACM MCLK output and should be configured by its
actual consumer rather than unconditionally claimed by a pinctrl hog.
Prepare for LCDIF support, which uses the same pin.

Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
 arch/arm64/boot/dts/freescale/imx8dxl-evk.dts | 12 +++++++++++-
 1 file changed, 11 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts b/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts
index 312e4ef3a6760..1ffc6047c1480 100644
--- a/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts
@@ -347,6 +347,11 @@ sound-wm8960-3 {
 	};
 };
 
+&acm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_mclk>;
+};
+
 &adc0 {
 	vref-supply = <&reg_vref_1v8>;
 	status = "okay";
@@ -945,7 +950,6 @@ pinctrl_hog: hoggrp {
 		fsl,pins = <
 			IMX8DXL_COMP_CTL_GPIO_1V8_3V3_GPIORHB_PAD	0x000514a0
 			IMX8DXL_COMP_CTL_GPIO_1V8_3V3_GPIORHK_PAD	0x000014a0
-			IMX8DXL_SPI3_CS0_ADMA_ACM_MCLK_OUT1		0x0600004c
 			IMX8DXL_SNVS_TAMPER_OUT1_LSIO_GPIO2_IO05_IN	0x0600004c
 		>;
 	};
@@ -1065,6 +1069,12 @@ IMX8DXL_SPI1_SDI_ADMA_I2C3_SCL		0x06000021
 		>;
 	};
 
+	pinctrl_mclk: mclkgrp {
+		fsl,pins = <
+			 IMX8DXL_SPI3_CS0_ADMA_ACM_MCLK_OUT1	0x0600004c
+		>;
+	};
+
 	pinctrl_lpuart0: lpuart0grp {
 		fsl,pins = <
 			IMX8DXL_UART0_RX_ADMA_UART0_RX		0x06000020

-- 
2.43.0

Re: [PATCH v3 6/7] arm64: dts: imx8dxl-evk: Move ACM MCLK pin to ACM pinctrl

[Liu Ying]

On Tue, Oct 20, 2026 at 04:12:56PM -0400, Frank.Li@oss.nxp.com wrote:
> From: Frank Li <Frank.Li@nxp.com>
> 
> Move the IMX8DXL_SPI3_CS0_ADMA_ACM_MCLK_OUT1 pin from the iomuxc hog
> group to the ACM pinctrl state.
> 
> The pin is used as the ACM MCLK output and should be configured by its
> actual consumer rather than unconditionally claimed by a pinctrl hog.
> Prepare for LCDIF support, which uses the same pin.
> 
> Signed-off-by: Frank Li <Frank.Li@nxp.com>
> ---
>  arch/arm64/boot/dts/freescale/imx8dxl-evk.dts | 12 +++++++++++-
>  1 file changed, 11 insertions(+), 1 deletion(-)

Acked-by: Liu Ying <victor.liu@nxp.com>

[PATCH v3 7/7] arm64: dts: imx8dxl-evk: add lcdif overlay

[Frank.Li]

From: Frank Li <Frank.Li@nxp.com>

Add lcd panel (waiken,101wx001-wct) support. This panel is only used at
imx8dxl evk boards. And evk board only supports one panel.

Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
Change in v3
- add panel info at overlay file.
- add bus-width = <18>, which only connect 18 lines.
- rename to waiken,101wx001-wct

change in v2
- remove iomux hog (sashiko)
- add power-supply
---
 arch/arm64/boot/dts/freescale/Makefile             |   3 +
 .../dts/freescale/imx8dxl-evk-lcdif-101wx001.dtso  | 119 +++++++++++++++++++++
 2 files changed, 122 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index a80cccf34eb56..b5d5e6bd8ce06 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -113,6 +113,9 @@ dtb-$(CONFIG_ARCH_MXC) += imx8dx-colibri-iris-v2.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8dx-colibri-iris.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8dxl-evk.dtb
 
+imx8dxl-evk-lcdif-101wx001-dtbs += imx8dxl-evk.dtb imx8dxl-evk-lcdif-101wx001.dtbo
+dtb-$(CONFIG_ARCH_MXC) += imx8dxl-evk-lcdif-101wx001.dtb
+
 imx8dxl-evk-pcie-ep-dtbs += imx8dxl-evk.dtb imx-pcie0-ep.dtbo
 dtb-$(CONFIG_ARCH_MXC) += imx8dxl-evk-pcie-ep.dtb
 DTC_FLAGS_imx8dxl-hummingboard-telematics := -@
diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-evk-lcdif-101wx001.dtso b/arch/arm64/boot/dts/freescale/imx8dxl-evk-lcdif-101wx001.dtso
new file mode 100644
index 0000000000000..39abf9b3884ea
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8dxl-evk-lcdif-101wx001.dtso
@@ -0,0 +1,119 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2026 NXP.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pads-imx8dxl.h>
+
+&{/} {
+	lcd_backlight: backlight {
+		compatible = "gpio-backlight";
+		gpios = <&pca6416_1 5 GPIO_ACTIVE_HIGH>;
+	};
+
+	lcd-panel {
+		compatible = "waiken,101wx001-wct";
+		backlight = <&lcd_backlight>;
+		power-supply = <&reg_lcd_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&lcdif_out>;
+			};
+		};
+	};
+
+	reg_lcd_3v3: regulator-lcd-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&acm {
+	status = "disabled";
+};
+
+&adma_lcdif {
+	pinctrl-0 = <&pinctrl_lcdif>, <&lcd_0_fun>, <&lcd_1_fun>, <&lcd_2_fun>, <&lcd_3_fun>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	port {
+		lcdif_out: endpoint {
+			bus-width = <18>;
+			remote-endpoint = <&panel_in>;
+		};
+	};
+};
+
+&cm40_lpuart {
+	status = "disabled";
+};
+
+&eqos {
+	status = "disabled";
+};
+
+&iomuxc {
+	pinctrl_lcdif: lcdifgrp {
+		fsl,pins = <
+			IMX8DXL_SPI3_SCK_ADMA_LCDIF_D00			0xe8000023
+			IMX8DXL_SPI3_SDO_ADMA_LCDIF_D01			0xe8000023
+			IMX8DXL_SPI3_SDI_ADMA_LCDIF_D02			0xe8000023
+			IMX8DXL_ENET1_RGMII_TXD3_ADMA_LCDIF_D03		0xd0000023
+			IMX8DXL_UART1_TX_ADMA_LCDIF_D04			0xe8000023
+			IMX8DXL_UART1_RX_ADMA_LCDIF_D05			0xe8000023
+			IMX8DXL_UART1_RTS_B_ADMA_LCDIF_D06		0xe8000023
+			IMX8DXL_UART1_CTS_B_ADMA_LCDIF_D07		0xe8000023
+			IMX8DXL_SPI0_SCK_ADMA_LCDIF_D08			0xe8000023
+			IMX8DXL_SPI0_SDI_ADMA_LCDIF_D09			0xe8000023
+			IMX8DXL_SPI0_SDO_ADMA_LCDIF_D10			0xe8000023
+			IMX8DXL_SPI0_CS1_ADMA_LCDIF_D11			0xe8000023
+			IMX8DXL_SPI0_CS0_ADMA_LCDIF_D12			0xe8000023
+			IMX8DXL_ADC_IN1_ADMA_LCDIF_D13			0xe8200003
+			IMX8DXL_ADC_IN0_ADMA_LCDIF_D14			0xe8200003
+			IMX8DXL_ADC_IN3_ADMA_LCDIF_D15			0xe8200003
+			IMX8DXL_ADC_IN2_ADMA_LCDIF_D16			0xe8200003
+			IMX8DXL_ADC_IN5_ADMA_LCDIF_D17			0xe8200003
+			IMX8DXL_SPI3_CS0_ADMA_LCDIF_HSYNC		0xd0000023
+			IMX8DXL_SPI3_CS1_ADMA_LCDIF_RESET		0xd0000023
+			IMX8DXL_MCLK_IN1_ADMA_LCDIF_EN			0xd0000023
+			IMX8DXL_MCLK_IN0_ADMA_LCDIF_VSYNC		0xd0000023
+			IMX8DXL_MCLK_OUT0_ADMA_LCDIF_CLK		0xd0000023
+		>;
+	};
+};
+
+&lpspi3 {
+	status = "disabled";
+};
+
+&lpuart1 {
+	status = "disabled";
+};
+
+&sai0 {
+	status = "disabled";
+};
+
+&sai1 {
+	status = "disabled";
+};
+
+&wm8960_1 {
+	status = "disabled";
+};
+
+&wm8960_2 {
+	status = "disabled";
+};
+
+&wm8960_3 {
+	status = "disabled";
+};

-- 
2.43.0

Re: [PATCH v3 7/7] arm64: dts: imx8dxl-evk: add lcdif overlay

[Liu Ying]

On Tue, Oct 20, 2026 at 04:12:57PM -0400, Frank.Li@oss.nxp.com wrote:
> From: Frank Li <Frank.Li@nxp.com>
> 
> Add lcd panel (waiken,101wx001-wct) support. This panel is only used at
> imx8dxl evk boards. And evk board only supports one panel.
> 
> Signed-off-by: Frank Li <Frank.Li@nxp.com>
> ---
> Change in v3
> - add panel info at overlay file.
> - add bus-width = <18>, which only connect 18 lines.
> - rename to waiken,101wx001-wct
> 
> change in v2
> - remove iomux hog (sashiko)
> - add power-supply
> ---
>  arch/arm64/boot/dts/freescale/Makefile             |   3 +
>  .../dts/freescale/imx8dxl-evk-lcdif-101wx001.dtso  | 119 +++++++++++++++++++++
>  2 files changed, 122 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index a80cccf34eb56..b5d5e6bd8ce06 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -113,6 +113,9 @@ dtb-$(CONFIG_ARCH_MXC) += imx8dx-colibri-iris-v2.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8dx-colibri-iris.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8dxl-evk.dtb
>  
> +imx8dxl-evk-lcdif-101wx001-dtbs += imx8dxl-evk.dtb imx8dxl-evk-lcdif-101wx001.dtbo
> +dtb-$(CONFIG_ARCH_MXC) += imx8dxl-evk-lcdif-101wx001.dtb

Use full panel type:
s/101wx001/101wx001_wct/

> +
>  imx8dxl-evk-pcie-ep-dtbs += imx8dxl-evk.dtb imx-pcie0-ep.dtbo
>  dtb-$(CONFIG_ARCH_MXC) += imx8dxl-evk-pcie-ep.dtb
>  DTC_FLAGS_imx8dxl-hummingboard-telematics := -@
> diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-evk-lcdif-101wx001.dtso b/arch/arm64/boot/dts/freescale/imx8dxl-evk-lcdif-101wx001.dtso
> new file mode 100644
> index 0000000000000..39abf9b3884ea
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8dxl-evk-lcdif-101wx001.dtso
> @@ -0,0 +1,119 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2026 NXP.
> + */
> +
> +/dts-v1/;
> +/plugin/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/pinctrl/pads-imx8dxl.h>
> +
> +&{/} {
> +	lcd_backlight: backlight {

Nit: s/lcd_backlight/backlight/

> +		compatible = "gpio-backlight";
> +		gpios = <&pca6416_1 5 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	lcd-panel {

Nit: s/lcd-panel/panel/

-- 
Regards,
Liu Ying