mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Sergey Shtylyov <s.shtylyov@omp.ru>
To: Paul Barker <paul@pbarker.dev>,
	"David S . Miller" <davem@davemloft.net>,
	Eric Dumazet <edumazet@google.com>,
	Jakub Kicinski <kuba@kernel.org>, Paolo Abeni <pabeni@redhat.com>
Cc: "Paul Barker" <paul.barker.ct@bp.renesas.com>,
	"Geert Uytterhoeven" <geert+renesas@glider.be>,
	"Niklas Söderlund" <niklas.soderlund+renesas@ragnatech.se>,
	"Biju Das" <biju.das.jz@bp.renesas.com>,
	"Claudiu Beznea" <claudiu.beznea.uj@bp.renesas.com>,
	netdev@vger.kernel.org, linux-renesas-soc@vger.kernel.org,
	linux-kernel@vger.kernel.org
Subject: Re: [net-next PATCH 05/11] net: ravb: Simplify types in RX csum validation
Date: Mon, 30 Sep 2024 22:11:17 +0300	[thread overview]
Message-ID: <b4707880-2be4-4132-a3e1-8b104b89828c@omp.ru> (raw)
In-Reply-To: <20240930160845.8520-6-paul@pbarker.dev>

On 9/30/24 19:08, Paul Barker wrote:

> From: Paul Barker <paul.barker.ct@bp.renesas.com>
> 
> The HW checksum value is used as a 16-bit flag, it is zero when the

   I think I prefer s/HW/hardware/ but there's no hard feelings... :-)

> checksum has been validated and non-zero otherwise. Therefore we don't
> need to treat this as an actual __wsum type or call csum_unfold(), we
> can just use a u16 pointer.
> 
> Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
[...]
> diff --git a/drivers/net/ethernet/renesas/ravb_main.c b/drivers/net/ethernet/renesas/ravb_main.c
> index 1dd2152734b0..9350ca10ab22 100644
> --- a/drivers/net/ethernet/renesas/ravb_main.c
> +++ b/drivers/net/ethernet/renesas/ravb_main.c
[...]
> @@ -762,23 +761,22 @@ static void ravb_rx_csum_gbeth(struct sk_buff *skb)
>  	 * The last 2 bytes are the protocol checksum status which will be zero
>  	 * if the checksum has been validated.
>  	 */
> -	if (unlikely(skb->len < sizeof(__sum16) * 2))
> +	csum_len = sizeof(*hw_csum) * 2;

   Could've been done by an initializer instead?

> +	if (unlikely(skb->len < csum_len))
>  		return;
>  
>  	if (skb_is_nonlinear(skb)) {
> -		last_frag = &shinfo->frags[shinfo->nr_frags - 1];
> -		hw_csum = skb_frag_address(last_frag) +
> -			  skb_frag_size(last_frag);
> -		skb_frag_size_sub(last_frag, 2 * sizeof(__sum16));
> +		skb_frag_t *last_frag = &shinfo->frags[shinfo->nr_frags - 1];

   Could've been done in the previous patch...

> +
> +		hw_csum = (u16 *)(skb_frag_address(last_frag) +
> +				  skb_frag_size(last_frag));
> +		skb_frag_size_sub(last_frag, csum_len);
>  	} else {
> -		hw_csum = skb_tail_pointer(skb);
> -		skb_trim(skb, skb->len - 2 * sizeof(__sum16));
> +		hw_csum = (u16 *)skb_tail_pointer(skb);
> +		skb_trim(skb, skb->len - csum_len);
>  	}
>  
> -	hw_csum -= sizeof(__sum16);
> -	csum_proto = csum_unfold((__force __sum16)get_unaligned_le16(hw_csum));
> -
> -	if (!csum_proto)
> +	if (!*--hw_csum)

   Hm, you lost get_unaligned_le16() here. The checksum can be anywhere,
unaligned too...

[...]

MBR, Sergey


  reply	other threads:[~2024-09-30 19:11 UTC|newest]

Thread overview: 31+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2024-09-30 16:08 [net-next PATCH 00/11] Extend GbEth checksum offload support to VLAN/IPv6 packets Paul Barker
2024-09-30 16:08 ` [net-next PATCH 01/11] net: ravb: Factor out checksum offload enable bits Paul Barker
2024-09-30 17:02   ` Sergey Shtylyov
2024-09-30 16:08 ` [net-next PATCH 02/11] net: ravb: Disable IP header RX checksum offloading Paul Barker
2024-09-30 17:16   ` Sergey Shtylyov
2024-09-30 16:08 ` [net-next PATCH 03/11] net: ravb: Drop IP protocol check from RX csum verification Paul Barker
2024-09-30 17:29   ` Sergey Shtylyov
2024-09-30 16:08 ` [net-next PATCH 04/11] net: ravb: Combine if conditions in RX csum validation Paul Barker
2024-09-30 17:40   ` Sergey Shtylyov
2024-09-30 16:08 ` [net-next PATCH 05/11] net: ravb: Simplify types " Paul Barker
2024-09-30 19:11   ` Sergey Shtylyov [this message]
2024-09-30 19:30     ` Sergey Shtylyov
2024-10-03  9:23     ` Paul Barker
2024-10-03 13:20       ` Sergey Shtylyov
2024-09-30 16:08 ` [net-next PATCH 06/11] net: ravb: Disable IP header TX checksum offloading Paul Barker
2024-09-30 19:23   ` Sergey Shtylyov
2024-09-30 16:08 ` [net-next PATCH 07/11] net: ravb: Simplify UDP TX checksum offload Paul Barker
2024-09-30 19:39   ` Sergey Shtylyov
2024-09-30 16:08 ` [net-next PATCH 08/11] net: ravb: Support ICMP TX checksum offload for GbEth Paul Barker
2024-09-30 19:48   ` Sergey Shtylyov
2024-09-30 16:08 ` [net-next PATCH 09/11] net: ravb: Enable IPv6 RX checksum offloading " Paul Barker
2024-09-30 19:55   ` Sergey Shtylyov
2024-09-30 16:08 ` [net-next PATCH 10/11] net: ravb: Enable IPv6 TX checksum offload " Paul Barker
2024-09-30 20:08   ` Sergey Shtylyov
2024-09-30 16:08 ` [net-next PATCH 11/11] net: ravb: Add VLAN checksum support Paul Barker
2024-09-30 20:36   ` Sergey Shtylyov
2024-09-30 22:32     ` Sergey Shtylyov
2024-10-01 10:44     ` Simon Horman
2024-10-02 15:27       ` Sergey Shtylyov
2024-10-03 10:26     ` Paul Barker
2024-10-01 16:46   ` kernel test robot

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=b4707880-2be4-4132-a3e1-8b104b89828c@omp.ru \
    --to=s.shtylyov@omp.ru \
    --cc=biju.das.jz@bp.renesas.com \
    --cc=claudiu.beznea.uj@bp.renesas.com \
    --cc=davem@davemloft.net \
    --cc=edumazet@google.com \
    --cc=geert+renesas@glider.be \
    --cc=kuba@kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-renesas-soc@vger.kernel.org \
    --cc=netdev@vger.kernel.org \
    --cc=niklas.soderlund+renesas@ragnatech.se \
    --cc=pabeni@redhat.com \
    --cc=paul.barker.ct@bp.renesas.com \
    --cc=paul@pbarker.dev \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®