* [PATCH] arm64: dts: qcom: sm7325: Remove duplicate motorola-dubai dts
@ 2026-10-18 21:16 Val Packett
2026-10-21 10:34 ` Konrad Dybcio
0 siblings, 1 reply; 2+ messages in thread
From: Val Packett @ 2026-10-18 21:16 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Abel Vesa, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Kees Cook, Tony Luck,
Guilherme G. Piccoli
Cc: Val Packett, linux-arm-msm, devicetree, linux-kernel
Both v2 and v3 of the patch series landed, so the non-split dts is
present alongside the common dtsi + split per display panel dts.
Remove the redundant non-split dts.
Signed-off-by: Val Packett <val@packett.cool>
---
arch/arm64/boot/dts/qcom/Makefile | 1 -
.../boot/dts/qcom/sm7325-motorola-dubai.dts | 1453 -----------------
2 files changed, 1454 deletions(-)
delete mode 100644 arch/arm64/boot/dts/qcom/sm7325-motorola-dubai.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 88230c4e00ea..20108bc2c231 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -397,7 +397,6 @@ dtb-$(CONFIG_ARCH_QCOM) += sm6375-sony-xperia-murray-pdx225.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm7125-xiaomi-curtana.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm7125-xiaomi-joyeuse.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm7225-fairphone-fp4.dtb
-dtb-$(CONFIG_ARCH_QCOM) += sm7325-motorola-dubai.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm7325-motorola-dubai-csot.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm7325-motorola-dubai-tianma.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm7325-nothing-spacewar.dtb
diff --git a/arch/arm64/boot/dts/qcom/sm7325-motorola-dubai.dts b/arch/arm64/boot/dts/qcom/sm7325-motorola-dubai.dts
deleted file mode 100644
index d94571c05a59..000000000000
--- a/arch/arm64/boot/dts/qcom/sm7325-motorola-dubai.dts
+++ /dev/null
@@ -1,1453 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
-/*
- * Copyright (c) 2026, Val Packett <val@packett.cool>
- */
-
-/dts-v1/;
-
-/* PM7250B is configured to use SID8/9 */
-#define PM7250B_SID 8
-#define PM7250B_SID1 9
-
-#include <dt-bindings/arm/qcom,ids.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/iio/qcom,spmi-adc7-pm7325.h>
-#include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h>
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
-
-#include "sm7325.dtsi"
-#include "pm7325.dtsi"
-#include "pm7250b.dtsi"
-#include "pm8350c.dtsi" /* PM7350C */
-#include "pmk8350.dtsi" /* PMK7325 */
-
-/ {
- model = "Motorola Edge 30";
- compatible = "motorola,dubai", "qcom,sm7325";
- chassis-type = "handset";
-
- aliases {
- bluetooth0 = &bluetooth;
- serial0 = &uart5;
- serial1 = &uart7;
- wifi0 = &wifi;
- };
-
- chosen {
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
-
- stdout-path = "serial0:115200n8";
-
- framebuffer {
- compatible = "simple-framebuffer";
- memory-region = <&framebuffer_mem>;
- width = <1080>;
- height = <2400>;
- stride = <(1080 * 4)>;
- format = "a8r8g8b8";
-
- clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
- <&dispcc DISP_CC_MDSS_MDP_CLK>,
- <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
- <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
- <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
- <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
- power-domains = <&dispcc DISP_CC_MDSS_CORE_GDSC>;
- };
- };
-
- gpio-keys {
- compatible = "gpio-keys";
-
- pinctrl-0 = <&kypd_vol_up_n>;
- pinctrl-names = "default";
-
- key-volume-up {
- label = "Volume Up";
- gpios = <&pm7325_gpios 6 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_VOLUMEUP>;
- };
- };
-
- pmic-glink {
- compatible = "qcom,sm7325-pmic-glink",
- "qcom,qcm6490-pmic-glink",
- "qcom,pmic-glink";
-
- #address-cells = <1>;
- #size-cells = <0>;
-
- orientation-gpios = <&tlmm 140 GPIO_ACTIVE_HIGH>;
-
- connector@0 {
- compatible = "usb-c-connector";
- reg = <0>;
-
- power-role = "dual";
- data-role = "dual";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
-
- pmic_glink_hs_in: endpoint {
- remote-endpoint = <&usb_1_dwc3_hs>;
- };
- };
-
- port@2 {
- reg = <2>;
-
- pmic_glink_sbu: endpoint {
- remote-endpoint = <&fsa4480_sbu_mux>;
- };
- };
- };
- };
- };
-
- reserved-memory {
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
-
- ramoops@ae000000 {
- compatible = "ramoops";
- reg = <0x0 0xae000000 0x0 0xc0000>;
- console-size = <0x40000>;
- mem-type = <2>;
- pmsg-size = <0x40000>;
- record-size = <0x3f800>;
- };
-
- removed@c0000000 {
- reg = <0x0 0xc0000000 0x0 0x5100000>;
- no-map;
- };
-
- framebuffer_mem: framebuffer@e1000000 {
- reg = <0x0 0xe1000000 0x0 (1080 * 2400 * 4)>;
- no-map;
- };
-
- linux,cma {
- compatible = "shared-dma-pool";
- size = <0x0 0x8000000>;
- reusable;
- linux,cma-default;
- };
- };
-
- thermal-zones {
- cam-flash-thermal {
- thermal-sensors = <&pmk8350_adc_tm 2>;
-
- trips {
- active-config0 {
- temperature = <125000>;
- hysteresis = <1000>;
- type = "passive";
- };
- };
- };
-
- chg-skin-thermal {
- thermal-sensors = <&pm7250b_adc_tm 0>;
-
- trips {
- active-config0 {
- temperature = <125000>;
- hysteresis = <1000>;
- type = "passive";
- };
- };
- };
-
- chg-thermal {
- thermal-sensors = <&pmk8350_adc_tm 4>;
-
- trips {
- active-config0 {
- temperature = <125000>;
- hysteresis = <1000>;
- type = "passive";
- };
- };
- };
-
- conn-thermal {
- thermal-sensors = <&pm7250b_adc_tm 1>;
-
- trips {
- active-config0 {
- temperature = <125000>;
- hysteresis = <1000>;
- type = "passive";
- };
- };
- };
-
- pa-1-thermal {
- thermal-sensors = <&pmk8350_adc_tm 5>;
-
- trips {
- active-config0 {
- temperature = <125000>;
- hysteresis = <1000>;
- type = "passive";
- };
- };
- };
-
- pa-2-thermal {
- thermal-sensors = <&pmk8350_adc_tm 6>;
-
- /* Reports negative temperature. */
- status = "disabled";
-
- trips {
- active-config0 {
- temperature = <125000>;
- hysteresis = <1000>;
- type = "passive";
- };
- };
- };
-
- quiet-thermal {
- thermal-sensors = <&pmk8350_adc_tm 1>;
-
- trips {
- active-config0 {
- temperature = <125000>;
- hysteresis = <1000>;
- type = "passive";
- };
- };
- };
-
- sdm-skin-thermal {
- thermal-sensors = <&pmk8350_adc_tm 3>;
-
- trips {
- active-config0 {
- temperature = <125000>;
- hysteresis = <1000>;
- type = "passive";
- };
- };
- };
-
- xo-thermal {
- thermal-sensors = <&pmk8350_adc_tm 0>;
-
- trips {
- active-config0 {
- temperature = <125000>;
- hysteresis = <1000>;
- type = "passive";
- };
- };
- };
- };
-
- // S2B is really ebi.lvl but it's there for supply map completeness sake.
- vreg_s2b_0p7: smpb2-regulator {
- compatible = "regulator-fixed";
- regulator-name = "vreg_s2b_0p7";
-
- regulator-min-microvolt = <65535>;
- regulator-max-microvolt = <65535>;
- regulator-always-on;
- vin-supply = <&vph_pwr>;
- };
-
- vph_pwr: vph-pwr-regulator {
- compatible = "regulator-fixed";
- regulator-name = "vph_pwr";
- regulator-min-microvolt = <3700000>;
- regulator-max-microvolt = <3700000>;
- };
-
- wcn6750-pmu {
- compatible = "qcom,wcn6750-pmu";
- pinctrl-0 = <&bt_en>;
- pinctrl-names = "default";
- vddaon-supply = <&mos_0p95_aon_s10c>;
- vddasd-supply = <&vreg_l11c_2p8>;
- vddpmu-supply = <&mos_0p95_dig_s10c>;
- vddio-supply = <&vdd18_io>;
- vddrfa0p8-supply = <&vdd09_pmu_rfa_i>;
- vddrfa1p2-supply = <&vdd13_pmu_rfa_i>;
- vddrfa1p7-supply = <&vdd19_pmu_rfa_i>;
- vddrfa2p2-supply = <&vdd22_wlpa_s1c>;
-
- bt-enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>;
-
- regulators {
- vreg_pmu_rfa_cmn: ldo0 {
- regulator-name = "vreg_pmu_rfa_cmn";
- };
-
- vreg_pmu_aon_0p59: ldo1 {
- regulator-name = "vreg_pmu_aon_0p59";
- };
-
- vreg_pmu_wlcx_0p8: ldo2 {
- regulator-name = "vreg_pmu_wlcx_0p8";
- };
-
- vreg_pmu_wlmx_0p85: ldo3 {
- regulator-name = "vreg_pmu_wlmx_0p85";
- };
-
- vreg_pmu_btcmx_0p85: ldo4 {
- regulator-name = "vreg_pmu_btcmx_0p85";
- };
-
- vreg_pmu_rfa_0p8: ldo5 {
- regulator-name = "vreg_pmu_rfa_0p8";
- };
-
- vreg_pmu_rfa_1p2: ldo6 {
- regulator-name = "vreg_pmu_rfa_1p2";
- };
-
- vreg_pmu_rfa_1p7: ldo7 {
- regulator-name = "vreg_pmu_rfa_1p7";
- };
-
- vreg_pmu_pcie_0p9: ldo8 {
- regulator-name = "vreg_pmu_pcie_0p9";
- };
-
- vreg_pmu_pcie_1p8: ldo9 {
- regulator-name = "vreg_pmu_pcie_1p8";
- };
- };
- };
-};
-
-&apps_rsc {
- regulators-0 {
- compatible = "qcom,pm7325-rpmh-regulators";
- qcom,pmic-id = "b";
-
- vdd-s1-supply = <&vph_pwr>;
- vdd-s2-supply = <&vph_pwr>;
- vdd-s7-supply = <&vph_pwr>;
- vdd-s8-supply = <&vph_pwr>;
-
- vdd-l1-l4-l12-l15-supply = <&vreg_s7b_0p952>;
- vdd-l2-l7-supply = <&vreg_bob>;
- vdd-l3-supply = <&vreg_s2b_0p7>;
- vdd-l5-supply = <&vreg_s2b_0p7>;
- vdd-l6-l9-l10-supply = <&vreg_s8b_1p256>;
- vdd-l8-supply = <&vreg_s7b_0p952>;
- vdd-l11-l17-l18-l19-supply = <&vreg_s1b_1p856>;
- vdd-l13-supply = <&vreg_s7b_0p952>;
- vdd-l14-l16-supply = <&vreg_s8b_1p256>;
-
- /*
- * S2, L4-L5 are ARCs:
- * S2 - ebi.lvl,
- * L4 - lmx.lvl,
- * l5 - lcx.lvl.
- *
- * L10 are unused.
- */
-
- vdd19_pmu_rfa_i:
- vreg_s1b_1p856: smps1 {
- regulator-name = "vreg_s1b_1p856";
- regulator-min-microvolt = <1840000>;
- regulator-max-microvolt = <2040000>;
- };
-
- mos_0p95_aon_s10c:
- mos_0p95_dig_s10c:
- vdd09_pmu_rfa_i:
- vreg_s7b_0p952: smps7 {
- regulator-name = "vreg_s7b_0p952";
- regulator-min-microvolt = <535000>;
- regulator-max-microvolt = <1120000>;
- };
-
- vdd13_pmu_rfa_i:
- vreg_s8b_1p256: smps8 {
- regulator-name = "vreg_s8b_1p256";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1500000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_RET>;
- };
-
- vreg_l1b_0p912: ldo1 {
- regulator-name = "vreg_l1b_0p912";
- regulator-min-microvolt = <825000>;
- regulator-max-microvolt = <925000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vdd_a_usbhs_3p1:
- vreg_l2b_3p072: ldo2 {
- regulator-name = "vreg_l2b_3p072";
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <3544000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l3b_0p6: ldo3 {
- regulator-name = "vreg_l3b_0p6";
- regulator-min-microvolt = <312000>;
- regulator-max-microvolt = <910000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vdd_a_dsi_0_1p2:
- vdd_a_ufs_0_1p2:
- vreg_l6b_1p2: ldo6 {
- regulator-name = "vreg_l6b_1p2";
- regulator-min-microvolt = <1140000>;
- regulator-max-microvolt = <1260000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
- RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l7b_2p96: ldo7 {
- regulator-name = "vreg_l7b_2p96";
- regulator-min-microvolt = <2400000>;
- regulator-max-microvolt = <3544000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
- RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l8b_0p904: ldo8 {
- regulator-name = "vreg_l8b_0p904";
- regulator-min-microvolt = <870000>;
- regulator-max-microvolt = <970000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l9b_1p2: ldo9 {
- regulator-name = "vreg_l9b_1p2";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1304000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
- RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l11b_1p776: ldo11 {
- regulator-name = "vreg_l11b_1p776";
- regulator-min-microvolt = <1504000>;
- regulator-max-microvolt = <2000000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l12b_0p8: ldo12 {
- regulator-name = "vreg_l12b_0p8";
- regulator-min-microvolt = <751000>;
- regulator-max-microvolt = <824000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l13b_0p8: ldo13 {
- regulator-name = "vreg_l13b_0p8";
- regulator-min-microvolt = <530000>;
- regulator-max-microvolt = <824000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l14b_1p2: ldo14 {
- regulator-name = "vreg_l14b_1p2";
- regulator-min-microvolt = <1080000>;
- regulator-max-microvolt = <1304000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l15b_0p88: ldo15 {
- regulator-name = "vreg_l15b_0p88";
- regulator-min-microvolt = <765000>;
- regulator-max-microvolt = <1020000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l16b_1p2: ldo16 {
- regulator-name = "vreg_l16b_1p2";
- regulator-min-microvolt = <1100000>;
- regulator-max-microvolt = <1300000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l17b_1p8: ldo17 {
- regulator-name = "vreg_l17b_1p8";
- regulator-min-microvolt = <1700000>;
- regulator-max-microvolt = <1900000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l18b_1p8: ldo18 {
- regulator-name = "vreg_l18b_1p8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2000000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- vdd18_io:
- vreg_l19b_1p8: ldo19 {
- regulator-name = "vreg_l19b_1p8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2000000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
- };
-
- regulators-1 {
- compatible = "qcom,pm8350c-rpmh-regulators";
- qcom,pmic-id = "c";
-
- vdd-s1-supply = <&vph_pwr>;
- vdd-s2-supply = <&vph_pwr>;
- vdd-s5-supply = <&vph_pwr>;
- vdd-s7-supply = <&vph_pwr>;
- vdd-s9-supply = <&vph_pwr>;
- vdd-s10-supply = <&vph_pwr>;
-
- vdd-l1-l12-supply = <&vreg_s1b_1p856>;
- vdd-l2-l8-supply = <&vreg_s1b_1p856>;
- vdd-l3-l4-l5-l7-l13-supply = <&vreg_bob>;
- vdd-l6-l9-l11-supply = <&vreg_bob>;
- vdd-l10-supply = <&vreg_s7b_0p952>;
-
- vdd-bob-supply = <&vph_pwr>;
-
- /*
- * S2, S5, S7, S10 are ARCs:
- * S2 - cx.lvl,
- * S5 - mss.lvl,
- * S7 - gfx.lvl,
- * S10 - mx.lvl.
- */
-
- vdd22_wlpa_s1c:
- vreg_s1c_2p2: smps1 {
- regulator-name = "vreg_s1c_2p2";
- regulator-min-microvolt = <2190000>;
- regulator-max-microvolt = <2210000>;
- };
-
- vreg_s9c_0p676: smps9 {
- regulator-name = "vreg_s9c_0p676";
- regulator-min-microvolt = <1010000>;
- regulator-max-microvolt = <1170000>;
- };
-
- vdd_a_usbhs_1p8:
- vdd_qfprom:
- vreg_l1c_1p8: ldo1 {
- regulator-name = "vreg_l1c_1p8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1980000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- iovdd_ts:
- vreg_l2c_1p8: ldo2 {
- regulator-name = "vreg_l2c_1p8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vdd_ts:
- vreg_l3c_3p0: ldo3 {
- regulator-name = "vreg_l3c_3p0";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3304000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l4c_1p8_3p0: ldo4 {
- regulator-name = "vreg_l4c_1p8_3p0";
- regulator-min-microvolt = <1620000>;
- regulator-max-microvolt = <3300000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l5c_1p8_3p0: ldo5 {
- regulator-name = "vreg_l5c_1p8_3p0";
- regulator-min-microvolt = <1620000>;
- regulator-max-microvolt = <3300000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l6c_2p96: ldo6 {
- regulator-name = "vreg_l6c_2p96";
- regulator-min-microvolt = <1650000>;
- regulator-max-microvolt = <3544000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l7c_3p0: ldo7 {
- regulator-name = "vreg_l7c_3p0";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3544000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l8c_1p8: ldo8 {
- regulator-name = "vreg_l8c_1p8";
- regulator-min-microvolt = <1620000>;
- regulator-max-microvolt = <2000000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l9c_3p3: ldo9 {
- regulator-name = "vreg_l9c_2p96";
- regulator-min-microvolt = <3008000>;
- regulator-max-microvolt = <3300000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vdd_a_dsi_0_0p9:
- vdd_a_ufs_0_core:
- vdd_a_usbhs_core:
- vreg_l10c_0p88: ldo10 {
- regulator-name = "vreg_l10c_0p88";
- regulator-min-microvolt = <720000>;
- regulator-max-microvolt = <1050000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
- RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l11c_2p8: ldo11 {
- regulator-name = "vreg_l11c_2p8";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <3544000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- disp_iovcc_1p8:
- vreg_l12c_1p8: ldo12 {
- regulator-name = "vreg_l12c_1p8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- disp_vci_3p0:
- vreg_l13c_3p0: ldo13 {
- regulator-name = "vreg_l13c_3p0";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- audio_sw_vcc:
- vreg_bob: bob {
- regulator-name = "vreg_bob";
- regulator-min-microvolt = <3008000>;
- regulator-max-microvolt = <3960000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
- };
- };
-};
-
-&gcc {
- protected-clocks = <GCC_CFG_NOC_LPASS_CLK>,
- <GCC_MSS_CFG_AHB_CLK>,
- <GCC_MSS_OFFLINE_AXI_CLK>,
- <GCC_MSS_Q6SS_BOOT_CLK_SRC>,
- <GCC_MSS_Q6_MEMNOC_AXI_CLK>,
- <GCC_MSS_SNOC_AXI_CLK>,
- <GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
- <GCC_QSPI_CORE_CLK>,
- <GCC_QSPI_CORE_CLK_SRC>,
- <GCC_SEC_CTRL_CLK_SRC>,
- <GCC_WPSS_AHB_BDG_MST_CLK>,
- <GCC_WPSS_AHB_CLK>,
- <GCC_WPSS_RSCP_CLK>;
-};
-
-&gpi_dma0 {
- status = "okay";
-};
-
-&gpi_dma1 {
- status = "okay";
-};
-
-&gpu {
- status = "okay";
-};
-
-&gpu_zap_shader {
- firmware-name = "qcom/sm7325/motorola/dubai/a660_zap.mbn";
-};
-
-&i2c4 {
- clock-frequency = <100000>;
-
- status = "okay";
-
- typec-mux@42 {
- compatible = "fcs,fsa4480";
- reg = <0x42>;
-
- interrupts-extended = <&tlmm 6 IRQ_TYPE_LEVEL_LOW>;
-
- vcc-supply = <&audio_sw_vcc>;
-
- mode-switch;
- orientation-switch;
-
- port {
- fsa4480_sbu_mux: endpoint {
- remote-endpoint = <&pmic_glink_sbu>;
- };
- };
- };
-};
-
-&ipa {
- firmware-name = "qcom/sm7325/motorola/dubai/yupik_ipa_fws.mbn";
-
- status = "okay";
-};
-
-&pm7250b_adc {
- channel@4e {
- reg = <ADC5_AMUX_THM2_100K_PU>;
- qcom,ratiometric;
- qcom,hw-settle-time = <200>;
- qcom,pre-scaling = <1 1>;
- label = "chg_skin_therm";
- };
-
- channel@4f {
- reg = <ADC5_AMUX_THM3_100K_PU>;
- qcom,ratiometric;
- qcom,hw-settle-time = <200>;
- qcom,pre-scaling = <1 1>;
- label = "conn_therm";
- };
-};
-
-&pm7250b_adc_tm {
- status = "okay";
-
- chg-skin-therm@0 {
- reg = <0>;
- io-channels = <&pm7250b_adc ADC5_AMUX_THM2_100K_PU>;
- qcom,ratiometric;
- qcom,hw-settle-time-us = <200>;
- };
-
- conn-therm@1 {
- reg = <1>;
- io-channels = <&pm7250b_adc ADC5_AMUX_THM3_100K_PU>;
- qcom,ratiometric;
- qcom,hw-settle-time-us = <200>;
- };
-};
-
-&pm7250b_gpios {
- gpio-line-names = "FG_ALERT_N", /* GPIO_1 */
- "SLAVECP_INT",
- "NC",
- "NC",
- "NC",
- "DOUBLER_STAT",
- "NC",
- "NC",
- "NC",
- "NC", /* GPIO_10 */
- "NC",
- "NC";
-};
-
-&pm7325_gpios {
- gpio-line-names = "PA_THERM1", /* GPIO_1 */
- "NC",
- "NC",
- "PA_THERM2",
- "CBL_PWR_N",
- "KYPD_VOL_UP_N",
- "NC",
- "NC",
- "NC",
- "NC"; /* GPIO_10 */
-
- kypd_vol_up_n: kypd-volp-n-state {
- pins = "gpio6";
- function = PMIC_GPIO_FUNC_NORMAL;
- bias-pull-up;
- input-enable;
- power-source = <1>;
- };
-};
-
-&pm8350c_gpios {
- gpio-line-names = "NC", /* GPIO_1 */
- "NC",
- "NC",
- "NC",
- "NC",
- "NC",
- "NC",
- "NC",
- "NC"; /* GPIO_9 */
-};
-
-&pm8350c_flash {
- status = "okay";
-
- led-0 {
- function = LED_FUNCTION_FLASH;
- color = <LED_COLOR_ID_WHITE>;
- led-sources = <1>, <4>;
- led-max-microamp = <500000>;
- flash-max-microamp = <1500000>;
- flash-max-timeout-us = <400000>;
- };
-
- led-1 {
- function = LED_FUNCTION_FLASH;
- color = <LED_COLOR_ID_WHITE>;
- led-sources = <2>, <3>;
- led-max-microamp = <500000>;
- flash-max-microamp = <1500000>;
- flash-max-timeout-us = <400000>;
- };
-};
-
-&pmk8350_adc_tm {
- status = "okay";
-
- xo-therm@0 {
- reg = <0>;
- io-channels = <&pmk8350_vadc PMK8350_ADC7_AMUX_THM1_100K_PU>;
- qcom,ratiometric;
- qcom,hw-settle-time-us = <200>;
- };
-
- quiet-therm@1 {
- reg = <1>;
- io-channels = <&pmk8350_vadc PM7325_ADC7_AMUX_THM1_100K_PU>;
- qcom,ratiometric;
- qcom,hw-settle-time-us = <200>;
- };
-
- cam-flash-therm@2 {
- reg = <2>;
- io-channels = <&pmk8350_vadc PM7325_ADC7_AMUX_THM2_100K_PU>;
- qcom,ratiometric;
- qcom,hw-settle-time-us = <200>;
- };
-
- sdm-skin-therm@3 {
- reg = <3>;
- io-channels = <&pmk8350_vadc PM7325_ADC7_AMUX_THM3_100K_PU>;
- qcom,ratiometric;
- qcom,hw-settle-time-us = <200>;
- };
-
- chg-therm@4 {
- reg = <4>;
- io-channels = <&pmk8350_vadc PM7325_ADC7_AMUX_THM4_100K_PU>;
- qcom,ratiometric;
- qcom,hw-settle-time-us = <200>;
- };
-
- pa-therm-1@5 {
- reg = <5>;
- io-channels = <&pmk8350_vadc PM7325_ADC7_GPIO1_100K_PU>;
- qcom,ratiometric;
- qcom,hw-settle-time-us = <200>;
- };
-
- pa-therm-2@6 {
- reg = <6>;
- io-channels = <&pmk8350_vadc PM7325_ADC7_GPIO4_100K_PU>;
- qcom,ratiometric;
- qcom,hw-settle-time-us = <200>;
- };
-};
-
-&pmk8350_gpios {
- gpio-line-names = "NC", /* GPIO_0 */
- "NC",
- "TP_PMK_GPIO_3",
- "PMK_OPTION"; /* GPIO_4 */
-};
-
-&pmk8350_rtc {
- status = "okay";
-};
-
-&pmk8350_vadc {
- status = "okay";
-
- channel@44 {
- reg = <PMK8350_ADC7_AMUX_THM1_100K_PU>;
- qcom,ratiometric;
- qcom,hw-settle-time = <200>;
- qcom,pre-scaling = <1 1>;
- label = "pmk8350_xo_therm";
- };
-
- channel@144 {
- reg = <PM7325_ADC7_AMUX_THM1_100K_PU>;
- qcom,ratiometric;
- qcom,hw-settle-time = <200>;
- qcom,pre-scaling = <1 1>;
- label = "pm7325_quiet_therm";
- };
-
- channel@145 {
- reg = <PM7325_ADC7_AMUX_THM2_100K_PU>;
- qcom,ratiometric;
- qcom,hw-settle-time = <200>;
- qcom,pre-scaling = <1 1>;
- label = "pm7325_cam_flash_therm";
- };
-
- channel@146 {
- reg = <PM7325_ADC7_AMUX_THM3_100K_PU>;
- qcom,ratiometric;
- qcom,hw-settle-time = <200>;
- qcom,pre-scaling = <1 1>;
- label = "pm7325_sdm_skin_therm";
- };
-
- channel@147 {
- reg = <PM7325_ADC7_AMUX_THM4_100K_PU>;
- qcom,ratiometric;
- qcom,hw-settle-time = <200>;
- qcom,pre-scaling = <1 1>;
- label = "pm7325_chg_therm";
- };
-
- channel@14a {
- reg = <PM7325_ADC7_GPIO1_100K_PU>;
- qcom,ratiometric;
- qcom,hw-settle-time = <200>;
- qcom,pre-scaling = <1 1>;
- label = "pm7325_pa_therm1";
- };
-
- channel@14d {
- reg = <PM7325_ADC7_GPIO4_100K_PU>;
- qcom,ratiometric;
- qcom,hw-settle-time = <200>;
- qcom,pre-scaling = <1 1>;
- label = "pm7325_pa_therm2";
- };
-};
-
-&pon_pwrkey {
- status = "okay";
-};
-
-&pon_resin {
- linux,code = <KEY_VOLUMEDOWN>;
-
- status = "okay";
-};
-
-&qfprom {
- vcc-supply = <&vdd_qfprom>;
-};
-
-&qup_spi13_cs {
- drive-strength = <6>;
- bias-pull-down;
-};
-
-&qup_spi13_data_clk {
- drive-strength = <6>;
- bias-pull-down;
-};
-
-&qup_uart5_rx {
- drive-strength = <2>;
- bias-disable;
-};
-
-&qup_uart5_tx {
- drive-strength = <2>;
- bias-disable;
-};
-
-&qup_uart7_cts {
- /*
- * Configure a bias-bus-hold on CTS to lower power
- * usage when Bluetooth is turned off. Bus hold will
- * maintain a low power state regardless of whether
- * the Bluetooth module drives the pin in either
- * direction or leaves the pin fully unpowered.
- */
- bias-bus-hold;
-};
-
-&qup_uart7_rts {
- /* We'll drive RTS, so no pull */
- drive-strength = <2>;
- bias-disable;
-};
-
-&qup_uart7_rx {
- /*
- * Configure a pull-up on RX. This is needed to avoid
- * garbage data when the TX pin of the Bluetooth module is
- * in tri-state (module powered off or not driving the
- * signal yet).
- */
- bias-pull-up;
-};
-
-&qup_uart7_tx {
- /* We'll drive TX, so no pull */
- drive-strength = <2>;
- bias-disable;
-};
-
-&qupv3_id_0 {
- status = "okay";
-};
-
-&qupv3_id_1 {
- status = "okay";
-};
-
-&remoteproc_adsp {
- firmware-name = "qcom/sm7325/motorola/dubai/adsp.mbn";
-
- status = "okay";
-};
-
-&remoteproc_cdsp {
- firmware-name = "qcom/sm7325/motorola/dubai/cdsp.mbn";
-
- status = "okay";
-};
-
-&remoteproc_mpss {
- firmware-name = "qcom/sm7325/motorola/dubai/modem.mbn";
-
- status = "okay";
-};
-
-&remoteproc_wpss {
- firmware-name = "qcom/sm7325/motorola/dubai/wpss.mbn";
-
- status = "okay";
-};
-
-&rmtfs_mem {
- qcom,vmid = <QCOM_SCM_VMID_MSS_MSA>,
- <QCOM_SCM_VMID_NAV>;
-};
-
-&spi13 {
- status = "okay";
-
- touchscreen@0 {
- compatible = "goodix,gt9916";
- reg = <0>;
-
- interrupts-extended = <&tlmm 81 IRQ_TYPE_LEVEL_LOW>;
-
- reset-gpios = <&tlmm 105 GPIO_ACTIVE_LOW>;
-
- avdd-supply = <&vdd_ts>;
- vddio-supply = <&iovdd_ts>;
-
- spi-max-frequency = <1000000>;
-
- touchscreen-size-x = <1080>;
- touchscreen-size-y = <2400>;
-
- pinctrl-0 = <&ts_int_n>, <&ts_reset_n>;
- pinctrl-names = "default";
- };
-};
-
-&tlmm {
- gpio-line-names = "NC", /* GPIO_0 */
- "NC",
- "NC",
- "NC",
- "SMARTPA_I2C_SDA",
- "SMARTPA_I2C_SCK",
- "AUD_4480_DET",
- "AUD_4480_INT",
- "FASTCHARGE_I2C_SDA",
- "FASTCHARGE_I2C_SCL",
- "SM_GPSLNA_EN_GPIO10", /* GPIO_10 */
- "NC",
- "PERI_I2C_SDA",
- "PERI_I2C_SCL",
- "NC",
- "NC",
- "APPS_I2C_SDA",
- "APPS_I2C_SCL",
- "NC",
- "DISP_LDO_EN",
- "CAM_FW_RST_N", /* GPIO_20 */
- "CAM_RM_RST_N",
- "DBG_UART_TXD",
- "DBG_UART_RXD",
- "TOPSB_INT_N",
- "MCAM_LDO_EN",
- "HOST2WLAN_SOL",
- "WLAN2HOST_SOL",
- "UART_BT_RTS_AP_CTS",
- "UART_BT_CTS_AP_RTS",
- "UART_BT_RX_AP_TX", /* GPIO_30 */
- "UART_BT_TX_AP_RX",
- "FRONT_60M_INT",
- "FRONT_60M_RST",
- "FP_INT",
- "FP_RST",
- "NFC_I2C_SDA",
- "NFC_I2C_SCL",
- "NFC_EN",
- "NFC_CLK_REQ",
- "NFC_SE_SPI_NREST", /* GPIO_40 */
- "NFC_IRQ",
- "RF_LDO_GPIO42_EN",
- "GOOGLE_KEY_INT", /* no such key exists */
- "DISP_RST_N",
- "SB_INT_N",
- "HAP_RST_N",
- "HAP_INT",
- "ESE_SPI_MISO",
- "ESE_SPI_MOSI",
- "ESE_SPI_CLK", /* GPIO_50 */
- "ESE_SPI_CS",
- "TP_SPI_MISO",
- "TP_SPI_MOSI",
- "TP_SPI_CLK",
- "TP_SPI_CS_N",
- "FP_SPI_MISO",
- "FP_SPI_MOSI",
- "FP_SPI_CLK",
- "FP_SPI_CS_N",
- "HW_ID_1", /* GPIO_60 */
- "HW_ID_2",
- "CAM_PMU_EN",
- "WIDE_DVDD_LDO_EN",
- "CAM_MCLK0",
- "CAM_MCLK1",
- "CAM_MCLK2",
- "CAM_MCLK3",
- "NC",
- "CCI_I2C_SDA0",
- "CCI_I2C_SCL0", /* GPIO_70 */
- "CCI_I2C_SDA1",
- "CCI_I2C_SCL1",
- "CCI_I2C_SDA2",
- "CCI_I2C_SCL2",
- "CCI_I2C_SDA3",
- "CCI_I2C_SCL3",
- "CAM_RT_RST_N",
- "CAM_RU_RST_N",
- "FCAM_LDO_EN",
- "DISP_TE", /* GPIO_80 */
- "TP_INT_N",
- "FORCED_USB_BOOT",
- "SM_CDC_RST_N",
- "WLAN_EN",
- "BT_EN",
- "WCN_SW_CTRL",
- "PCIE0_RESET_N",
- "PCIE0_CLK_REQ_N",
- "PCIE0_WAKE_N",
- "MOS_AS_EN", /* GPIO_90 */
- "NC",
- "",
- "NC",
- "BT_FM_SLIMBUS_CLK",
- "BT_FM_SLIMBUS_DATA",
- "NC",
- "RFCONN_DET_1",
- "RF_CON_DET_2",
- "RF_CON_DET_3",
- "NC", /* GPIO_100 */
- "NC",
- "NC",
- "ACCEL_INT",
- "NC",
- "TP_RST_N",
- "NC",
- "NC",
- "NC",
- "UIM2_DATA",
- "UIM2_CLK", /* GPIO_110 */
- "UIM2_RESET",
- "UIM2_PRESENT",
- "UIM1_DATA",
- "UIM1_CLK",
- "UIM1_RESET",
- "UIM1_PRESENT",
- "SM_RFFE0_CLK",
- "SM_RFFE0_DATA",
- "SM_RFFE1_CLK",
- "SM_RFFE1_DATA", /* GPIO_120 */
- "PA_MUTING",
- "SM_GRFC5",
- "LAA_RX",
- "SM_GRFC7",
- "SM_RFFE4_CLK",
- "SM_RFFE4_DATA",
- "WLAN_COEX_UART_RX",
- "WLAN_COEX_UART_TX",
- "NC",
- "NC", /* GPIO_130 */
- "SM_GRFC12",
- "NC",
- "QLINK0_REQUEST",
- "QLINK0_ENABLE",
- "QLINK0_WMSS_RESET_N",
- "NC",
- "NC",
- "NC",
- "NC",
- "USB_CC_DIR", /* GPIO_140 */
- "SAR_INT_N",
- "PROX_INT_N",
- "",
- "SM_SWR_TX_CLK",
- "SM_SWR_TX_DATA0",
- "SM_SWR_TX_DATA1",
- "SM_SWR_RX_CLK",
- "SM_SWR_RX_DATA0",
- "SM_SWR_RX_DATA1",
- "NC", /* GPIO_150 */
- "NC",
- "NC",
- "NC",
- "SB_MI2S_SCK",
- "SB_MI2S_WS",
- "SB_MI2S_RXDAT_AP_TX",
- "SB_MI2S_TXDAT_AP_RX",
- "NC",
- "SNS_I3C0_SDA",
- "SNS_I3C0_SCL", /* GPIO_160 */
- "SSC_I2C4_SDA",
- "SSC_I2C4_SCL",
- "MAG_I2C_SDA",
- "MAG_I2C_SCL",
- "NC",
- "NC",
- "",
- "",
- "",
- "", /* GPIO_170 */
- "SSC_BT_UART4_TX",
- "SSC_BT_UART4_RX",
- "NC",
- "NC";
- gpio-reserved-ranges = <48 4>, /* SPI (eSE - embedded Secure Element) */
- <56 4>; /* SPI (fingerprint reader) */
-
- qup_uart7_sleep_cts: qup-uart7-sleep-cts-state {
- pins = "gpio28";
- function = "gpio";
- /*
- * Configure a bias-bus-hold on CTS to lower power
- * usage when Bluetooth is turned off. Bus hold will
- * maintain a low power state regardless of whether
- * the Bluetooth module drives the pin in either
- * direction or leaves the pin fully unpowered.
- */
- bias-bus-hold;
- };
-
- qup_uart7_sleep_rts: qup-uart7-sleep-rts-state {
- pins = "gpio29";
- function = "gpio";
- /*
- * Configure pull-down on RTS. As RTS is active low
- * signal, pull it low to indicate the BT SoC that it
- * can wakeup the system anytime from suspend state by
- * pulling RX low (by sending wakeup bytes).
- */
- bias-pull-down;
- };
-
- qup_uart7_sleep_tx: qup-uart7-sleep-tx-state {
- pins = "gpio30";
- function = "gpio";
- /*
- * Configure pull-up on TX when it isn't actively driven
- * to prevent BT SoC from receiving garbage during sleep.
- */
- bias-pull-up;
- };
-
- qup_uart7_sleep_rx: qup-uart7-sleep-rx-state {
- pins = "gpio31";
- function = "gpio";
- /*
- * Configure a pull-up on RX. This is needed to avoid
- * garbage data when the TX pin of the Bluetooth module
- * is floating which may cause spurious wakeups.
- */
- bias-pull-up;
- };
-
- oled_reset_n: oled-reset-n-state {
- pins = "gpio44";
- function = "gpio";
- drive-strength = <8>;
- bias-disable;
- };
-
- aw86224_reset_default: aw86224-reset-default-state {
- pins = "gpio46";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-down;
- };
-
- aw86224_int_default: aw86224-int-default-state {
- pins = "gpio47";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
-
- mdp_vsync_p: mdp-vsync-p-state {
- pins = "gpio80";
- function = "mdp_vsync";
- drive-strength = <2>;
- bias-pull-down;
- };
-
- ts_int_n: ts-int-n-state {
- pins = "gpio81";
- function = "gpio";
- drive-strength = <8>;
- bias-pull-up;
- };
-
- bt_en: bt-en-state {
- pins = "gpio85";
- function = "gpio";
- output-low;
- bias-disable;
- };
-
- ts_reset_n: ts-int-n-state {
- pins = "gpio105";
- function = "gpio";
- drive-strength = <8>;
- bias-pull-up;
- };
-};
-
-&uart5 {
- status = "okay";
-};
-
-&uart7 {
- /delete-property/ interrupts;
- interrupts-extended = <&intc GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>,
- <&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
- pinctrl-1 = <&qup_uart7_sleep_cts>,
- <&qup_uart7_sleep_rts>,
- <&qup_uart7_sleep_tx>,
- <&qup_uart7_sleep_rx>;
- pinctrl-names = "default",
- "sleep";
-
- status = "okay";
-
- bluetooth: bluetooth {
- compatible = "qcom,wcn6750-bt";
-
- vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
- vddaon-supply = <&vreg_pmu_aon_0p59>;
- vddbtcmx-supply = <&vreg_pmu_btcmx_0p85>;
- vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
- vddrfa1p7-supply = <&vreg_pmu_rfa_1p7>;
- vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
-
- max-speed = <3200000>;
-
- qcom,local-bd-address-broken;
- };
-};
-
-&ufs_mem_hc {
- reset-gpios = <&tlmm 175 GPIO_ACTIVE_LOW>;
-
- vcc-supply = <&vreg_l7b_2p96>;
- vcc-max-microamp = <800000>;
-
- vccq-supply = <&vreg_l9b_1p2>;
- vccq-max-microamp = <900000>;
-
- status = "okay";
-};
-
-&ufs_mem_phy {
- vdda-phy-supply = <&vdd_a_ufs_0_core>;
- vdda-pll-supply = <&vdd_a_ufs_0_1p2>;
-
- status = "okay";
-};
-
-&usb_1 {
- /* USB 2.0 only */
- qcom,select-utmi-as-pipe-clk;
- maximum-speed = "high-speed";
-
- /* Remove USB3 phy */
- phys = <&usb_1_hsphy>;
- phy-names = "usb2-phy";
-
- status = "okay";
-};
-
-&usb_1_dwc3_hs {
- remote-endpoint = <&pmic_glink_hs_in>;
-};
-
-&usb_1_hsphy {
- vdda-pll-supply = <&vdd_a_usbhs_core>;
- vdda18-supply = <&vdd_a_usbhs_1p8>;
- vdda33-supply = <&vdd_a_usbhs_3p1>;
-
- status = "okay";
-};
-
-&venus {
- firmware-name = "qcom/sm7325/motorola/dubai/vpu20_1v.mbn";
-
- status = "okay";
-};
-
-&wifi {
- qcom,calibration-variant = "Motorola_dubai";
-
- status = "okay";
-};
--
2.55.0
^ permalink raw reply [flat|nested] 2+ messages in thread* Re: [PATCH] arm64: dts: qcom: sm7325: Remove duplicate motorola-dubai dts
2026-10-18 21:16 [PATCH] arm64: dts: qcom: sm7325: Remove duplicate motorola-dubai dts Val Packett
@ 2026-10-21 10:34 ` Konrad Dybcio
0 siblings, 0 replies; 2+ messages in thread
From: Konrad Dybcio @ 2026-10-21 10:34 UTC (permalink / raw)
To: Val Packett, Bjorn Andersson, Konrad Dybcio, Abel Vesa,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Kees Cook,
Tony Luck, Guilherme G. Piccoli
Cc: linux-arm-msm, devicetree, linux-kernel
On 10/18/26 11:16 PM, Val Packett wrote:
> Both v2 and v3 of the patch series landed, so the non-split dts is
> present alongside the common dtsi + split per display panel dts.
> Remove the redundant non-split dts.
>
> Signed-off-by: Val Packett <val@packett.cool>
> ---
Acked-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Konrad
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2026-10-21 10:34 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2026-10-18 21:16 [PATCH] arm64: dts: qcom: sm7325: Remove duplicate motorola-dubai dts Val Packett
2026-10-21 10:34 ` Konrad Dybcio
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®