mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
To: Kuogee Hsieh <quic_khsieh@quicinc.com>,
	robdclark@gmail.com, sean@poorly.run, swboyd@chromium.org,
	dianders@chromium.org, vkoul@kernel.org, daniel@ffwll.ch,
	airlied@gmail.com, agross@kernel.org, andersson@kernel.org
Cc: quic_abhinavk@quicinc.com, quic_sbillaka@quicinc.com,
	freedreno@lists.freedesktop.org, dri-devel@lists.freedesktop.org,
	linux-arm-msm@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH v2] drm/msm/dp: do not complete dp_aux_cmd_fifo_tx() if irq is not for aux transfer
Date: Thu, 15 Dec 2022 20:46:42 +0200	[thread overview]
Message-ID: <ca15a54b-8040-5e4f-a78e-12b7f8a554e1@linaro.org> (raw)
In-Reply-To: <1671129159-31105-1-git-send-email-quic_khsieh@quicinc.com>

On 15/12/2022 20:32, Kuogee Hsieh wrote:
> There are 3 possible interrupt sources are handled by DP controller,
> HPDstatus, Controller state changes and Aux read/write transaction.
> At every irq, DP controller have to check isr status of every interrupt
> sources and service the interrupt if its isr status bits shows interrupts
> are pending. There is potential race condition may happen at current aux
> isr handler implementation since it is always complete dp_aux_cmd_fifo_tx()
> even irq is not for aux read or write transaction. This may cause aux read
> transaction return premature if host aux data read is in the middle of
> waiting for sink to complete transferring data to host while irq happen.
> This will cause host's receiving buffer contains unexpected data. This
> patch fixes this problem by checking aux isr and return immediately at
> aux isr handler if there are no any isr status bits set.
> 
> Current there is a bug report regrading eDP edid corruption happen during
> system booting up. After lengthy debugging to found that VIDEO_READY
> interrupt was continuously firing during system booting up which cause
> dp_aux_isr() to complete dp_aux_cmd_fifo_tx() prematurely to retrieve data
> from aux hardware buffer which is not yet contains complete data transfer
> from sink. This cause edid corruption.
> 
> Follows are the signature at kernel logs when problem happen,
> EDID has corrupt header
> panel-simple-dp-aux aux-aea0000.edp: Couldn't identify panel via EDID
> panel-simple-dp-aux aux-aea0000.edp: error -EIO: Couldn't detect panel nor find a fallback
> 
> Changes in v2:
> -- do complete if (ret == IRQ_HANDLED) ay dp-aux_isr()
> -- add more commit text

Usually it's a single dash.

> 
> Fixes: c943b4948b58 ("drm/msm/dp: add displayPort driver support")
> 
> Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>

There should be no empty lines between the tags.

> Tested-by: Douglas Anderson <dianders@chromium.org>
> Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
> ---
>   drivers/gpu/drm/msm/dp/dp_aux.c | 87 +++++++++++++++++++++++++++++------------
>   1 file changed, 63 insertions(+), 24 deletions(-)
> 
> diff --git a/drivers/gpu/drm/msm/dp/dp_aux.c b/drivers/gpu/drm/msm/dp/dp_aux.c
> index d030a93..f31e5c1 100644
> --- a/drivers/gpu/drm/msm/dp/dp_aux.c
> +++ b/drivers/gpu/drm/msm/dp/dp_aux.c
> @@ -162,45 +162,78 @@ static ssize_t dp_aux_cmd_fifo_rx(struct dp_aux_private *aux,
>   	return i;
>   }
>   
> -static void dp_aux_native_handler(struct dp_aux_private *aux, u32 isr)
> +static irqreturn_t dp_aux_native_handler(struct dp_aux_private *aux, u32 isr)
>   {
> -	if (isr & DP_INTR_AUX_I2C_DONE)
> +	irqreturn_t ret = IRQ_NONE;
> +
> +	if (isr & DP_INTR_AUX_I2C_DONE) {
>   		aux->aux_error_num = DP_AUX_ERR_NONE;
> -	else if (isr & DP_INTR_WRONG_ADDR)
> +		ret = IRQ_HANDLED;
> +	} else if (isr & DP_INTR_WRONG_ADDR) {
>   		aux->aux_error_num = DP_AUX_ERR_ADDR;
> -	else if (isr & DP_INTR_TIMEOUT)
> +		ret = IRQ_HANDLED;
> +	} else if (isr & DP_INTR_TIMEOUT) {
>   		aux->aux_error_num = DP_AUX_ERR_TOUT;
> -	if (isr & DP_INTR_NACK_DEFER)
> +		ret = IRQ_HANDLED;
> +	}
> +
> +	if (isr & DP_INTR_NACK_DEFER) {
>   		aux->aux_error_num = DP_AUX_ERR_NACK;
> +		ret = IRQ_HANDLED;
> +	}
> +
>   	if (isr & DP_INTR_AUX_ERROR) {
>   		aux->aux_error_num = DP_AUX_ERR_PHY;
>   		dp_catalog_aux_clear_hw_interrupts(aux->catalog);
> +		ret = IRQ_HANDLED;
>   	}
> +
> +	return ret;
>   }
>   
> -static void dp_aux_i2c_handler(struct dp_aux_private *aux, u32 isr)
> +static irqreturn_t dp_aux_i2c_handler(struct dp_aux_private *aux, u32 isr)
>   {
> +	irqreturn_t ret = IRQ_NONE;
> +
>   	if (isr & DP_INTR_AUX_I2C_DONE) {
>   		if (isr & (DP_INTR_I2C_NACK | DP_INTR_I2C_DEFER))
>   			aux->aux_error_num = DP_AUX_ERR_NACK;
>   		else
>   			aux->aux_error_num = DP_AUX_ERR_NONE;
> -	} else {
> -		if (isr & DP_INTR_WRONG_ADDR)
> -			aux->aux_error_num = DP_AUX_ERR_ADDR;
> -		else if (isr & DP_INTR_TIMEOUT)
> -			aux->aux_error_num = DP_AUX_ERR_TOUT;
> -		if (isr & DP_INTR_NACK_DEFER)
> -			aux->aux_error_num = DP_AUX_ERR_NACK_DEFER;
> -		if (isr & DP_INTR_I2C_NACK)
> -			aux->aux_error_num = DP_AUX_ERR_NACK;
> -		if (isr & DP_INTR_I2C_DEFER)
> -			aux->aux_error_num = DP_AUX_ERR_DEFER;
> -		if (isr & DP_INTR_AUX_ERROR) {
> -			aux->aux_error_num = DP_AUX_ERR_PHY;
> -			dp_catalog_aux_clear_hw_interrupts(aux->catalog);
> -		}
> +
> +		return IRQ_HANDLED;
> +	}
> +
> +	if (isr & DP_INTR_WRONG_ADDR) {
> +		aux->aux_error_num = DP_AUX_ERR_ADDR;
> +		ret = IRQ_HANDLED;
> +	} else if (isr & DP_INTR_TIMEOUT) {
> +		aux->aux_error_num = DP_AUX_ERR_TOUT;
> +		ret = IRQ_HANDLED;
>   	}
> +
> +	if (isr & DP_INTR_NACK_DEFER) {
> +		aux->aux_error_num = DP_AUX_ERR_NACK_DEFER;
> +		ret = IRQ_HANDLED;
> +	}
> +
> +	if (isr & DP_INTR_I2C_NACK) {
> +		aux->aux_error_num = DP_AUX_ERR_NACK;
> +		ret = IRQ_HANDLED;
> +	}
> +
> +	if (isr & DP_INTR_I2C_DEFER) {
> +		aux->aux_error_num = DP_AUX_ERR_DEFER;
> +		ret = IRQ_HANDLED;
> +	}
> +
> +	if (isr & DP_INTR_AUX_ERROR) {
> +		aux->aux_error_num = DP_AUX_ERR_PHY;
> +		dp_catalog_aux_clear_hw_interrupts(aux->catalog);
> +		ret = IRQ_HANDLED;
> +	}
> +
> +	return ret;
>   }
>   
>   static void dp_aux_update_offset_and_segment(struct dp_aux_private *aux,
> @@ -413,6 +446,7 @@ void dp_aux_isr(struct drm_dp_aux *dp_aux)
>   {
>   	u32 isr;
>   	struct dp_aux_private *aux;
> +	irqreturn_t ret = IRQ_NONE;

No need to assign a value here. It will be overwritten in both of code 
branches.

>   
>   	if (!dp_aux) {
>   		DRM_ERROR("invalid input\n");
> @@ -423,15 +457,20 @@ void dp_aux_isr(struct drm_dp_aux *dp_aux)
>   
>   	isr = dp_catalog_aux_get_irq(aux->catalog);
>   
> +	/* no interrupts pending, return immediately */
> +	if (!isr)
> +		return;
> +

A separate commit please.

>   	if (!aux->cmd_busy)
>   		return;
>   
>   	if (aux->native)
> -		dp_aux_native_handler(aux, isr);
> +		ret = dp_aux_native_handler(aux, isr);
>   	else
> -		dp_aux_i2c_handler(aux, isr);
> +		ret = dp_aux_i2c_handler(aux, isr);
>   
> -	complete(&aux->comp);
> +	if (ret == IRQ_HANDLED)
> +		complete(&aux->comp);

Can you just move the complete() into the individual handling functions? 
Then you won't have to return the error code from dp_aux_*_handler() at 
all. You can check `isr' in that function and call complete if there was 
any error.

Also could you please describe, why is it necessary to complete() 
condition at all? Judging from your commit message the `if (!isr) 
return;' part should be enough.

>   }
>   
>   void dp_aux_reconfig(struct drm_dp_aux *dp_aux)

-- 
With best wishes
Dmitry


  reply	other threads:[~2022-12-15 18:47 UTC|newest]

Thread overview: 8+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2022-12-15 18:32 Kuogee Hsieh
2022-12-15 18:46 ` Dmitry Baryshkov [this message]
2022-12-15 20:10   ` Stephen Boyd
2022-12-15 20:12     ` Kuogee Hsieh
2022-12-15 21:15     ` Dmitry Baryshkov
2022-12-15 21:23       ` Kuogee Hsieh
2022-12-15 21:57       ` Abhinav Kumar
2022-12-15 20:30   ` Abhinav Kumar

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=ca15a54b-8040-5e4f-a78e-12b7f8a554e1@linaro.org \
    --to=dmitry.baryshkov@linaro.org \
    --cc=agross@kernel.org \
    --cc=airlied@gmail.com \
    --cc=andersson@kernel.org \
    --cc=daniel@ffwll.ch \
    --cc=dianders@chromium.org \
    --cc=dri-devel@lists.freedesktop.org \
    --cc=freedreno@lists.freedesktop.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=quic_abhinavk@quicinc.com \
    --cc=quic_khsieh@quicinc.com \
    --cc=quic_sbillaka@quicinc.com \
    --cc=robdclark@gmail.com \
    --cc=sean@poorly.run \
    --cc=swboyd@chromium.org \
    --cc=vkoul@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®