[PATCH net-next v3 0/9] net: dsa: realtek: rtl8365mb: add support for RTL8367S-VB

[PATCH net-next v3 0/9] net: dsa: realtek: rtl8365mb: add support for RTL8367S-VB

[Mieczyslaw Nalewaj]

This series adds support for the RTL8367S-VB (chip ID 0x6642) to the
rtl8365mb driver. The chip belongs to a new "family D" that differs from
the existing family C in its VLAN table layout, speed/RGMII configuration
and SerDes (SDS13) handling.

Patch 1 documents the chip in the devicetree binding.
Patch 2 adds the chip family infrastructure (no functional change).
Patches 3-4 add port speed and RGMII mode configuration for family D.
Patches 5-6 add VLAN 4k table access and raw-VID PVID handling.
Patches 7-8 add SDS13 PCS support and re-latching of the SerDes.
Patch 9 adds the RTL8367S-VB chip table entry. It comes last, so that
no intermediate commit exposes a family D chip with incomplete
handling and the series stays bisectable.

Family C's functional behaviour is unchanged. The only change in a
shared path is a mutex serializing SerDes register access, added in
patch 8. The port count is capped at 8 for family D only (patch 9).

Tested on TP-Link Archer AX55 v1 (RTL8367S-VB, CPU port over HSGMII to ipq5018)
with bridge VLAN filtering and per-port PVIDs.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
---
v3:
  - add a dt-bindings patch (1/9): RTL8367S-VB listed under
    realtek,rtl8365mb
  - add chip family infrastructure as its own patch (2/9), no
    functional change
  - squash the family D PVID getter and the PVID set/clear patches
    into one (6/9), so the read and write paths use the same register
    layout at every point of the series
  - add the RTL8367S-VB chip table entry last (9/9), after the family
    D speed, RGMII, VLAN and PCS support, so no intermediate commit
    can reach the chip with incomplete handling (reported by the
    automated review)
  - 6/9: fix the commit message (port p's write lands in port p >> 1)
    and update the stale kernel-doc and file comments
  - 8/9: start the re-latch work only for 2500base-x, cancel it from
    .pcs_disable, from pcs_config() and via a devres action; retry the
    SDS_MISC restore and come back soon if it fails; rewrite the
    commit message to match the code (reported by the automated
    review)
  - 9/9: document family D in the file header comment and in the
    learn limit comment (limit confirmed against the Realtek vendor
    API)

v2: https://lore.kernel.org/netdev/28382f3f-03c1-4606-9b11-86f118abeafe@yahoo.com/
  - 2/8: mask r_speed to the width of the FORCE_SPEED field before passing
    it to FIELD_PREP(), so that the family D 2500M value (5) cannot trip
    the compile-time range check; bit 2 still goes to FORCE_SPEED2
    (reported by the automated review).
  - 4/8: the commit message now explains why EXT_TXC_DLY[5:3] is cleared
    for RGMII on EXT1: the vendor RGMII setup does it, and the init jam
    table leaves the field at 2, which would add an extra TX delay on top
    of tx-internal-delay-ps. Add a comment describing the EXT_TXC_DLY
    layout (Andrew Lunn's review).
  - 8/8: document the new struct rtl8365mb members in the kernel-doc
    comment (sds_lock, sds_relatch, sds_relatch_count,
    sds_misc_target_val), which fixes the kernel-doc warnings.
  - 1/8, 3/8, 5/8, 6/8, 7/8: no changes.

v1: https://lore.kernel.org/netdev/84fc7483-b22d-45ea-a3b8-3285dc357265@yahoo.com/

Mieczyslaw Nalewaj (9):
  dt-bindings: net: dsa: realtek: add RTL8367S-VB
  net: dsa: realtek: rtl8365mb: add chip family infrastructure
  net: dsa: realtek: rtl8365mb: set speed for family D
  net: dsa: realtek: rtl8365mb: set RGMII mode for family D
  net: dsa: realtek: rtl8365mb: set and get vlan 4k for family D
  net: dsa: realtek: rtl8365mb: use raw VID for PVID on family D
  net: dsa: realtek: rtl8365mb: add family D SDS13 PCS support
  net: dsa: realtek: rtl8365mb: re-latch the family D SerDes
  net: dsa: realtek: rtl8365mb: add support for RTL8367S-VB

 .../devicetree/bindings/net/dsa/realtek.yaml  |   2 +-
 drivers/net/dsa/realtek/rtl8365mb.h           |  14 +
 drivers/net/dsa/realtek/rtl8365mb_main.c      | 603 ++++++++++++++++--
 drivers/net/dsa/realtek/rtl8365mb_vlan.c      | 342 ++++++++--
 4 files changed, 844 insertions(+), 117 deletions(-)
 create mode 100644 drivers/net/dsa/realtek/rtl8365mb.h

-- 
2.53.0

[PATCH net-next v3 1/9] dt-bindings: net: dsa: realtek: add RTL8367S-VB

[Mieczyslaw Nalewaj]

The RTL8367S-VB (chip ID 0x6642) is supported by the rtl8365mb driver.
Like the other models in the family, it is identified by its chip ID
register, so it does not need a compatible string of its own. List it
under realtek,rtl8365mb.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
---
 Documentation/devicetree/bindings/net/dsa/realtek.yaml | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/net/dsa/realtek.yaml b/Documentation/devicetree/bindings/net/dsa/realtek.yaml
index 473facd..ca775f6 100644
--- a/Documentation/devicetree/bindings/net/dsa/realtek.yaml
+++ b/Documentation/devicetree/bindings/net/dsa/realtek.yaml
@@ -43,7 +43,7 @@ properties:
       realtek,rtl8365mb:
         Use with models RTL8363NB, RTL8363NB-VB, RTL8363SC, RTL8363SC-VB,
         RTL8364NB, RTL8364NB-VB, RTL8365MB, RTL8366SC, RTL8367RB-VB, RTL8367S,
-        RTL8367SB, RTL8370MB, RTL8310SR
+        RTL8367S-VB, RTL8367SB, RTL8370MB, RTL8310SR
       realtek,rtl8366rb:
         Use with models RTL8366RB, RTL8366S
 
-- 
2.53.0

[PATCH net-next v3 2/9] net: dsa: realtek: rtl8365mb: add chip family infrastructure

[Mieczyslaw Nalewaj]

Add enum rtl8365mb_family and a family member to struct
rtl8365mb_chip_info, together with rtl8365mb_get_family() declared in a
new rtl8365mb.h so that the VLAN code can use it too. Tag all existing
chips as RTL8365MB_FAMILY_C.

RTL8365MB_FAMILY_D is defined here but no chip uses it yet; it is needed
by the following patches, which add family D handling for chips whose
register layout differs from the existing ones.

No functional change.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
---
 drivers/net/dsa/realtek/rtl8365mb.h      | 14 ++++++++++++++
 drivers/net/dsa/realtek/rtl8365mb_main.c | 14 ++++++++++++++
 2 files changed, 28 insertions(+)
 create mode 100644 drivers/net/dsa/realtek/rtl8365mb.h

diff --git a/drivers/net/dsa/realtek/rtl8365mb.h b/drivers/net/dsa/realtek/rtl8365mb.h
new file mode 100644
index 0000000..315de4c
--- /dev/null
+++ b/drivers/net/dsa/realtek/rtl8365mb.h
@@ -0,0 +1,14 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _RTL8365MB_H
+#define _RTL8365MB_H
+
+#include "realtek.h"
+
+enum rtl8365mb_family {
+	RTL8365MB_FAMILY_C,
+	RTL8365MB_FAMILY_D,
+};
+
+enum rtl8365mb_family rtl8365mb_get_family(struct realtek_priv *priv);
+
+#endif /* _RTL8365MB_H */
diff --git a/drivers/net/dsa/realtek/rtl8365mb_main.c b/drivers/net/dsa/realtek/rtl8365mb_main.c
index da06f95..840db5a 100644
--- a/drivers/net/dsa/realtek/rtl8365mb_main.c
+++ b/drivers/net/dsa/realtek/rtl8365mb_main.c
@@ -110,6 +110,7 @@
 #include "rtl83xx.h"
 #include "rtl8365mb_l2.h"
 #include "rtl8365mb_vlan.h"
+#include "rtl8365mb.h"
 
 /* Family-specific data and limits */
 #define RTL8365MB_PHYADDRMAX		7
@@ -707,6 +708,7 @@ struct rtl8365mb_extint {
  * @name: human-readable chip name
  * @chip_id: chip identifier
  * @chip_ver: chip silicon revision
+ * @family: chip family
  * @extints: available external interfaces
  * @jam_table: chip-specific initialization jam table
  * @jam_size: size of the chip's jam table
@@ -719,6 +721,7 @@ struct rtl8365mb_chip_info {
 	const char *name;
 	u32 chip_id;
 	u32 chip_ver;
+	enum rtl8365mb_family family;
 	const struct rtl8365mb_extint extints[RTL8365MB_MAX_NUM_EXTINTS];
 	const struct rtl8365mb_jam_tbl_entry *jam_table;
 	size_t jam_size;
@@ -731,6 +734,7 @@ static const struct rtl8365mb_chip_info rtl8365mb_chip_infos[] = {
 		.name = "RTL8365MB-VC",
 		.chip_id = 0x6367,
 		.chip_ver = 0x0040,
+		.family = RTL8365MB_FAMILY_C,
 		.extints = {
 			{ 6, 1, PHY_INTF(MII) | PHY_INTF(TMII) |
 				PHY_INTF(RMII) | PHY_INTF(RGMII) },
@@ -742,6 +746,7 @@ static const struct rtl8365mb_chip_info rtl8365mb_chip_infos[] = {
 		.name = "RTL8367S",
 		.chip_id = 0x6367,
 		.chip_ver = 0x00A0,
+		.family = RTL8365MB_FAMILY_C,
 		.extints = {
 			{ 6, 1, PHY_INTF(SGMII) | PHY_INTF(HSGMII) },
 			{ 7, 2, PHY_INTF(MII) | PHY_INTF(TMII) |
@@ -754,6 +759,7 @@ static const struct rtl8365mb_chip_info rtl8365mb_chip_infos[] = {
 		.name = "RTL8367SB",
 		.chip_id = 0x6367,
 		.chip_ver = 0x0010,
+		.family = RTL8365MB_FAMILY_C,
 		.extints = {
 			{ 6, 1, PHY_INTF(MII) | PHY_INTF(TMII) |
 				PHY_INTF(RMII) | PHY_INTF(RGMII) |
@@ -768,6 +774,7 @@ static const struct rtl8365mb_chip_info rtl8365mb_chip_infos[] = {
 		.name = "RTL8367RB-VB",
 		.chip_id = 0x6367,
 		.chip_ver = 0x0020,
+		.family = RTL8365MB_FAMILY_C,
 		.extints = {
 			{ 6, 1, PHY_INTF(MII) | PHY_INTF(TMII) |
 				PHY_INTF(RMII) | PHY_INTF(RGMII) },
@@ -874,6 +881,13 @@ struct rtl8365mb {
 
 #define pcs_to_rtl8365mb(_pcs) container_of((_pcs), struct rtl8365mb, pcs)
 
+enum rtl8365mb_family rtl8365mb_get_family(struct realtek_priv *priv)
+{
+	struct rtl8365mb *mb = priv->chip_data;
+
+	return mb->chip_info->family;
+}
+
 static int rtl8365mb_phy_poll_busy(struct realtek_priv *priv)
 {
 	u32 val;
-- 
2.53.0

[PATCH net-next v3 3/9] net: dsa: realtek: rtl8365mb: set speed for family D

[Mieczyslaw Nalewaj]

On family C hardware, forcing a 2.5 Gbps link speed requires relying
strictly on the HSGMII SerDes configuration block, while forcing a dummy
1 Gbps value inside the standard digital interface register. Family D
introduces a dedicated hardware link speed value (5) for 2500M. The speed
bitfield width has been expanded to 3 bits, splitting the most significant
bit into a new separate register field (FORCE_SPEED2), which maps directly
to a distinct per-port digital interface force layout.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
---
 drivers/net/dsa/realtek/rtl8365mb_main.c | 75 ++++++++++++++++++++----
 1 file changed, 62 insertions(+), 13 deletions(-)

diff --git a/drivers/net/dsa/realtek/rtl8365mb_main.c b/drivers/net/dsa/realtek/rtl8365mb_main.c
index 840db5a..8f3295c 100644
--- a/drivers/net/dsa/realtek/rtl8365mb_main.c
+++ b/drivers/net/dsa/realtek/rtl8365mb_main.c
@@ -344,6 +344,7 @@
 #define RTL8365MB_PORT_SPEED_10M	0
 #define RTL8365MB_PORT_SPEED_100M	1
 #define RTL8365MB_PORT_SPEED_1000M	2
+#define RTL8365MB_D_PORT_SPEED_2500M	5
 
 /* External interface force configuration registers 0~2 */
 #define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG0		0x1310 /* EXT0 */
@@ -361,6 +362,21 @@
 #define   RTL8365MB_DIGITAL_INTERFACE_FORCE_LINK_MASK		BIT(4)
 #define   RTL8365MB_DIGITAL_INTERFACE_FORCE_DUPLEX_MASK		BIT(2)
 #define   RTL8365MB_DIGITAL_INTERFACE_FORCE_SPEED_MASK		GENMASK(1, 0)
+/* Width of the FORCE_SPEED field, bits[1:0] */
+#define   RTL8365MB_DIGITAL_INTERFACE_FORCE_SPEED_WIDTH		2
+
+/* bits[13:12]; bit 13 reserved, no defined speed value uses it yet */
+#define   RTL8365MB_D_DIGITAL_INTERFACE_FORCE_SPEED2_MASK	GENMASK(13, 12)
+
+#define RTL8365MB_D_DIGITAL_INTERFACE_FORCE_REG_BASE		0x12c0
+#define RTL8365MB_D_DIGITAL_INTERFACE_FORCE_REG(_port) \
+		(RTL8365MB_D_DIGITAL_INTERFACE_FORCE_REG_BASE + (_port))
+
+#define RTL8365MB_D_DIGITAL_INTERFACE_FORCE_EN_BASE		0x12c8
+#define RTL8365MB_D_DIGITAL_INTERFACE_FORCE_REG_EN(_port) \
+		(RTL8365MB_D_DIGITAL_INTERFACE_FORCE_EN_BASE + (_port))
+
+#define RTL8365MB_D_DIGITAL_INTERFACE_FORCE_EN_ALL_MASK	GENMASK(15, 0)
 
 /* CPU port mask register - controls which ports are treated as CPU ports */
 #define RTL8365MB_CPU_PORT_MASK_REG	0x1219
@@ -1646,23 +1662,32 @@ static int rtl8365mb_ext_config_forcemode(struct realtek_priv *priv, int port,
 	u32 r_duplex;
 	u32 r_speed;
 	u32 r_link;
+	bool is_d;
 	int val;
 	int ret;
 
 	if (!extint)
 		return -ENODEV;
 
+	is_d = rtl8365mb_get_family(priv) == RTL8365MB_FAMILY_D;
 	if (link) {
 		/* Force the link up with the desired configuration */
 		r_link = 1;
 		r_rx_pause = rx_pause ? 1 : 0;
 		r_tx_pause = tx_pause ? 1 : 0;
 
-		/* The speed field has no value for 2.5 Gbps: the rate is
-		 * determined by the HSGMII SerDes configuration, and the
-		 * vendor driver programs the 1 Gbps value here.
-		 */
-		if (speed == SPEED_2500 || speed == SPEED_1000) {
+		if (speed == SPEED_2500) {
+			if (is_d) {
+				r_speed = RTL8365MB_D_PORT_SPEED_2500M;
+			} else {
+				/* The speed field has no value for 2.5 Gbps:
+				 * the rate is determined by the HSGMII SerDes
+				 * configuration, and the vendor driver programs
+				 * the 1 Gbps value here.
+				 */
+				r_speed = RTL8365MB_PORT_SPEED_1000M;
+			}
+		} else if (speed == SPEED_1000) {
 			r_speed = RTL8365MB_PORT_SPEED_1000M;
 		} else if (speed == SPEED_100) {
 			r_speed = RTL8365MB_PORT_SPEED_100M;
@@ -1692,20 +1717,44 @@ static int rtl8365mb_ext_config_forcemode(struct realtek_priv *priv, int port,
 		r_duplex = 0;
 	}
 
-	val = FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_EN_MASK, 1) |
-	      FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_TXPAUSE_MASK,
+	val = FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_TXPAUSE_MASK,
 			 r_tx_pause) |
 	      FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_RXPAUSE_MASK,
 			 r_rx_pause) |
 	      FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_LINK_MASK, r_link) |
 	      FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_DUPLEX_MASK,
 			 r_duplex) |
-	      FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_SPEED_MASK, r_speed);
-	ret = regmap_write(priv->map,
-			   RTL8365MB_DIGITAL_INTERFACE_FORCE_REG(extint->id),
-			   val);
-	if (ret)
-		return ret;
+	      FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_SPEED_MASK,
+			 r_speed &
+			 RTL8365MB_DIGITAL_INTERFACE_FORCE_SPEED_MASK);
+
+	if (is_d) {
+		/* Speed is 3 bits on family D: bits[1:0] go into FORCE_SPEED,
+		 * bit[2] goes into FORCE_SPEED2 (bit 12); only 2500M sets it,
+		 * bit 13 of the field is unused.
+		 */
+		val |= FIELD_PREP(RTL8365MB_D_DIGITAL_INTERFACE_FORCE_SPEED2_MASK,
+				  r_speed >>
+				  RTL8365MB_DIGITAL_INTERFACE_FORCE_SPEED_WIDTH);
+		ret = regmap_write(priv->map,
+				   RTL8365MB_D_DIGITAL_INTERFACE_FORCE_REG(port),
+				   val);
+		if (ret)
+			return ret;
+
+		ret = regmap_write(priv->map,
+				   RTL8365MB_D_DIGITAL_INTERFACE_FORCE_REG_EN(port),
+				   RTL8365MB_D_DIGITAL_INTERFACE_FORCE_EN_ALL_MASK);
+		if (ret)
+			return ret;
+	} else {
+		val |= FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_EN_MASK, 1);
+		ret = regmap_write(priv->map,
+				   RTL8365MB_DIGITAL_INTERFACE_FORCE_REG(extint->id),
+				   val);
+		if (ret)
+			return ret;
+	}
 
 	return 0;
 }
-- 
2.53.0

[PATCH net-next v3 4/9] net: dsa: realtek: rtl8365mb: set RGMII mode for family D

[Mieczyslaw Nalewaj]

On family D, RGMII on extension interface 1 needs two things that the
other families do not: the EXT1 RGMII TX clock delay field in
EXT_TXC_DLY (0x13f9, bits [5:3]) must be cleared, and the pin mux in
the top-level configuration register must be set up.

The vendor RGMII setup for EXT1 clears the RGMII field of EXT_TXC_DLY
(0x13f9, bits [5:3]) in addition to programming TXDELAY in RGMXF.
Do the same. The init jam table writes 0x0090 to this register, which
leaves the field at 2, so without the clear an extra TX delay would be
applied on top of tx-internal-delay-ps. Clearing it makes
tx-internal-delay-ps the only source of TX delay.

If the internal MAC4 block is not occupying extension 1, bind the
RGMII/MII pins to MAC7. SerDes 1, which shares the pins, is always
disabled.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
---
 drivers/net/dsa/realtek/rtl8365mb_main.c | 50 ++++++++++++++++++++++++
 1 file changed, 50 insertions(+)

diff --git a/drivers/net/dsa/realtek/rtl8365mb_main.c b/drivers/net/dsa/realtek/rtl8365mb_main.c
index 8f3295c..c15b88b 100644
--- a/drivers/net/dsa/realtek/rtl8365mb_main.c
+++ b/drivers/net/dsa/realtek/rtl8365mb_main.c
@@ -332,6 +332,12 @@
 #define   RTL8365MB_SDS_OPTION_ARM_KEY		0x0249
 #define RTL8365MB_SDS_OPTION_REG		0x13C1
 
+#define RTL8365MB_D_SDS_MISC_MODE_FIELD_MASK		GENMASK(4, 0)
+/* Shared "disable" encoding for both SDS_MISC's and SDS1_MISC0's
+ * 5-bit mode fields.
+ */
+#define RTL8365MB_D_PORT_SDS_MODE_DISABLE		0x1f
+
 /* Embedded DW8051 microcontroller control registers. The microcontroller
  * can run firmware to manage the SerDes link, but this driver keeps it in
  * reset and disabled: phylink already performs the link management that
@@ -458,6 +464,20 @@
 #define   RTL8365MB_PORT_MISC_CFG_VLAN_EGRESS_MODE_MASK		GENMASK(5, 4)
 #define   RTL8365MB_PORT_MISC_CFG_CONGESTION_SUSTAIN_TIME_MASK	GENMASK(3, 0)
 
+/* EXT_TXC_DLY holds a 3-bit TX clock delay per external interface, for
+ * RGMII ([2:0] EXT0, [5:3] EXT1, [8:6] EXT2) and separately for GMII.
+ * Only the EXT1 RGMII field is used here, and it is cleared in RGMII
+ * mode so that tx-internal-delay-ps is the only TX delay applied.
+ */
+#define RTL8365MB_D_REG_EXT_TXC_DLY				0x13f9
+#define   RTL8365MB_D_EXT1_RGMII_TX_DLY_MASK			GENMASK(5, 3)
+
+#define RTL8365MB_D_REG_TOP_CON0				0x1d70
+#define   RTL8365MB_D_MAC7_SEL_EXT1_MASK			BIT(13)
+#define   RTL8365MB_D_MAC4_SEL_EXT1_MASK			BIT(12)
+
+#define RTL8365MB_D_REG_SDS1_MISC0				0x1d78
+
 /**
  * enum rtl8365mb_vlan_egress_mode - port VLAN egress mode
  * @RTL8365MB_VLAN_EGRESS_MODE_ORIGINAL: follow untag mask in VLAN4k table entry
@@ -1194,6 +1214,7 @@ static int rtl8365mb_ext_config_rgmii(struct realtek_priv *priv, int port,
 	struct dsa_port *dp;
 	int tx_delay = 0;
 	int rx_delay = 0;
+	u32 data;
 	u32 val;
 	int ret;
 
@@ -1263,6 +1284,35 @@ static int rtl8365mb_ext_config_rgmii(struct realtek_priv *priv, int port,
 	if (ret)
 		return ret;
 
+	if (rtl8365mb_get_family(priv) == RTL8365MB_FAMILY_D &&
+	    extint->id == 1) {
+		ret = regmap_update_bits(priv->map,
+					 RTL8365MB_D_REG_EXT_TXC_DLY,
+					 RTL8365MB_D_EXT1_RGMII_TX_DLY_MASK, 0);
+		if (ret)
+			return ret;
+		/* Configure RGMII/MII mux to port 7 if UTP_PORT4 is not in
+		 * RGMII mode
+		 */
+		ret = regmap_read(priv->map, RTL8365MB_D_REG_TOP_CON0, &data);
+		if (ret)
+			return ret;
+		if ((data & RTL8365MB_D_MAC4_SEL_EXT1_MASK) == 0) {
+			ret = regmap_update_bits(priv->map,
+						 RTL8365MB_D_REG_TOP_CON0,
+						 RTL8365MB_D_MAC7_SEL_EXT1_MASK,
+						 RTL8365MB_D_MAC7_SEL_EXT1_MASK);
+			if (ret)
+				return ret;
+		}
+		ret = regmap_update_bits(priv->map,
+					 RTL8365MB_D_REG_SDS1_MISC0,
+					 RTL8365MB_D_SDS_MISC_MODE_FIELD_MASK,
+					 RTL8365MB_D_PORT_SDS_MODE_DISABLE);
+		if (ret)
+			return ret;
+	}
+
 	return 0;
 }
 
-- 
2.53.0

[PATCH net-next v3 5/9] net: dsa: realtek: rtl8365mb: set and get vlan 4k for family D

[Mieczyslaw Nalewaj]

The hardware structure of 4K VLAN table entries has changed between
silicon families. Family D's CVLAN entry is two 16-bit words rather
than three: there is no third word extending member/untag past bit 7,
and no priority/meter fields at all. The FID field is restricted to a
narrower 2-bit width. The chip itself supports both IVL and SVL, but
this driver always requests IVL for VLAN 4K entries
(rtl8365mb_vlan_4k_port_set() sets ivl_en = true on both families), so
that control bit is forced here to match existing driver behavior,
not a hardware limitation.

Reusing the three-word family C layout unconditionally means the third
word is read from and written back to the register that holds it on
family C, but does not exist as a distinct table word on family D's
die; whatever data happens to be there gets folded into member/untag
bits [10:8] on read, and re-written on every read-modify-write cycle
in rtl8365mb_vlan_4k_port_set(). Give family D its own two-word
pack/unpack instead.

The two-word layout matches the vendor switch API for this chip
family, which writes only 0x0510/0x0511 for a CVLAN entry.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
---
 drivers/net/dsa/realtek/rtl8365mb_vlan.c | 161 ++++++++++++++++-------
 1 file changed, 112 insertions(+), 49 deletions(-)

diff --git a/drivers/net/dsa/realtek/rtl8365mb_vlan.c b/drivers/net/dsa/realtek/rtl8365mb_vlan.c
index 8d49ffa..2c4c5ba 100644
--- a/drivers/net/dsa/realtek/rtl8365mb_vlan.c
+++ b/drivers/net/dsa/realtek/rtl8365mb_vlan.c
@@ -48,12 +48,14 @@
 
 #include "rtl8365mb_vlan.h"
 #include "rtl8365mb_table.h"
+#include "rtl8365mb.h"
 #include <linux/if_bridge.h>
 #include <linux/lockdep.h>
 #include <linux/regmap.h>
 
 /* CVLAN (i.e. VLAN4k) table entry layout, u16[3] */
 #define RTL8365MB_CVLAN_ENTRY_SIZE			3 /* 48-bits */
+#define RTL8365MB_D_CVLAN_ENTRY_SIZE			2 /* 32-bits */
 #define RTL8365MB_CVLAN_ENTRY_D0_MBR_MASK		GENMASK(7, 0)
 #define   RTL8365MB_CVLAN_MBR_LO_MASK			GENMASK(7, 0)
 #define RTL8365MB_CVLAN_ENTRY_D0_UNTAG_MASK		GENMASK(15, 8)
@@ -65,6 +67,10 @@
 #define RTL8365MB_CVLAN_ENTRY_D1_METERIDX_MASK		GENMASK(13, 9)
 #define   RTL8365MB_CVLAN_METERIDX_LO_MASK		GENMASK(4, 0)
 #define RTL8365MB_CVLAN_ENTRY_D1_IVL_SVL_MASK		GENMASK(14, 14)
+#define RTL8365MB_D_CVLAN_ENTRY_D1_SVLAN_CHK_IVL_SVL_MASK \
+							GENMASK(2, 2)
+#define RTL8365MB_D_CVLAN_ENTRY_D1_IVL_EN_MASK		GENMASK(3, 3)
+#define RTL8365MB_D_CVLAN_ENTRY_D1_FID_MASK		GENMASK(1, 0)
 /* extends RTL8365MB_CVLAN_ENTRY_D0_MBR_MASK */
 #define RTL8365MB_CVLAN_ENTRY_D2_MBR_EXT_MASK		GENMASK(2, 0)
 #define   RTL8365MB_CVLAN_MBR_HI_MASK			GENMASK(10, 8)
@@ -185,13 +191,16 @@ struct rtl8365mb_vlanmc {
 static int rtl8365mb_vlan_4k_read(struct realtek_priv *priv, u16 vid,
 				  struct rtl8365mb_vlan4k *vlan4k)
 {
+	bool is_d = rtl8365mb_get_family(priv) == RTL8365MB_FAMILY_D;
+	size_t entry_size = is_d ? RTL8365MB_D_CVLAN_ENTRY_SIZE :
+				   RTL8365MB_CVLAN_ENTRY_SIZE;
 	u16 data[RTL8365MB_CVLAN_ENTRY_SIZE];
 	int val;
 	int ret;
 
 	ret = rtl8365mb_table_query(priv, RTL8365MB_TABLE_CVLAN,
 				    RTL8365MB_TABLE_OP_READ, &vid, 0, 0,
-				    data, ARRAY_SIZE(data));
+				    data, entry_size);
 	if (ret)
 		return ret;
 
@@ -199,33 +208,61 @@ static int rtl8365mb_vlan_4k_read(struct realtek_priv *priv, u16 vid,
 	memset(vlan4k, 0, sizeof(*vlan4k));
 	vlan4k->vid = vid;
 
+	/* member/untag: d0[7:0]/d0[15:8] on both families. Family C
+	 * extends these into data[2] bits [2:0]/[5:3] for its 9th-11th
+	 * ports; family D's die has only 8 ports and no third table
+	 * word, so data[2] does not exist there and must not be read.
+	 */
 	val = FIELD_GET(RTL8365MB_CVLAN_ENTRY_D0_MBR_MASK, data[0]);
 	vlan4k->member = FIELD_PREP(RTL8365MB_CVLAN_MBR_LO_MASK, val);
-	val = FIELD_GET(RTL8365MB_CVLAN_ENTRY_D2_MBR_EXT_MASK, data[2]);
-	vlan4k->member |= FIELD_PREP(RTL8365MB_CVLAN_MBR_HI_MASK, val);
+	if (!is_d) {
+		val = FIELD_GET(RTL8365MB_CVLAN_ENTRY_D2_MBR_EXT_MASK, data[2]);
+		vlan4k->member |= FIELD_PREP(RTL8365MB_CVLAN_MBR_HI_MASK, val);
+	}
 
 	val = FIELD_GET(RTL8365MB_CVLAN_ENTRY_D0_UNTAG_MASK, data[0]);
 	vlan4k->untag = FIELD_PREP(RTL8365MB_CVLAN_UNTAG_LO_MASK, val);
-	val = FIELD_GET(RTL8365MB_CVLAN_ENTRY_D2_UNTAG_EXT_MASK, data[2]);
-	vlan4k->untag |= FIELD_PREP(RTL8365MB_CVLAN_UNTAG_HI_MASK, val);
-
-	vlan4k->fid = FIELD_GET(RTL8365MB_CVLAN_ENTRY_D1_FID_MASK, data[1]);
-	vlan4k->priority_en =
-		FIELD_GET(RTL8365MB_CVLAN_ENTRY_D1_VBPEN_MASK, data[1]);
-	vlan4k->priority =
-		FIELD_GET(RTL8365MB_CVLAN_ENTRY_D1_VBPRI_MASK, data[1]);
-	vlan4k->policing_en =
-		FIELD_GET(RTL8365MB_CVLAN_ENTRY_D1_ENVLANPOL_MASK, data[1]);
-
-	val = FIELD_GET(RTL8365MB_CVLAN_ENTRY_D1_METERIDX_MASK, data[1]);
-	val = FIELD_PREP(RTL8365MB_CVLAN_METERIDX_LO_MASK, val);
-	vlan4k->meteridx = val;
-	val = FIELD_GET(RTL8365MB_CVLAN_ENTRY_D2_METERIDX_EXT_MASK, data[2]);
-	val = FIELD_PREP(RTL8365MB_CVLAN_METERIDX_HI_MASK, val);
-	vlan4k->meteridx |= val;
-
-	vlan4k->ivl_en =
-		FIELD_GET(RTL8365MB_CVLAN_ENTRY_D1_IVL_SVL_MASK, data[1]);
+	if (!is_d) {
+		val = FIELD_GET(RTL8365MB_CVLAN_ENTRY_D2_UNTAG_EXT_MASK,
+				data[2]);
+		vlan4k->untag |= FIELD_PREP(RTL8365MB_CVLAN_UNTAG_HI_MASK, val);
+	}
+
+	if (is_d) {
+		vlan4k->fid = FIELD_GET(RTL8365MB_D_CVLAN_ENTRY_D1_FID_MASK,
+					data[1]);
+		/* Family D has no priority/meter fields in this entry -
+		 * left zeroed by the memset() above.
+		 */
+		vlan4k->ivl_en =
+			FIELD_GET(RTL8365MB_D_CVLAN_ENTRY_D1_IVL_EN_MASK,
+				  data[1]);
+	} else {
+		vlan4k->fid = FIELD_GET(RTL8365MB_CVLAN_ENTRY_D1_FID_MASK,
+					data[1]);
+		vlan4k->priority_en =
+			FIELD_GET(RTL8365MB_CVLAN_ENTRY_D1_VBPEN_MASK,
+				  data[1]);
+		vlan4k->priority =
+			FIELD_GET(RTL8365MB_CVLAN_ENTRY_D1_VBPRI_MASK,
+				  data[1]);
+		vlan4k->policing_en =
+			FIELD_GET(RTL8365MB_CVLAN_ENTRY_D1_ENVLANPOL_MASK,
+				  data[1]);
+
+		val = FIELD_GET(RTL8365MB_CVLAN_ENTRY_D1_METERIDX_MASK,
+				data[1]);
+		val = FIELD_PREP(RTL8365MB_CVLAN_METERIDX_LO_MASK, val);
+		vlan4k->meteridx = val;
+		val = FIELD_GET(RTL8365MB_CVLAN_ENTRY_D2_METERIDX_EXT_MASK,
+				data[2]);
+		val = FIELD_PREP(RTL8365MB_CVLAN_METERIDX_HI_MASK, val);
+		vlan4k->meteridx |= val;
+
+		vlan4k->ivl_en =
+			FIELD_GET(RTL8365MB_CVLAN_ENTRY_D1_IVL_SVL_MASK,
+				  data[1]);
+	}
 
 	return 0;
 }
@@ -233,6 +270,9 @@ static int rtl8365mb_vlan_4k_read(struct realtek_priv *priv, u16 vid,
 static int rtl8365mb_vlan_4k_write(struct realtek_priv *priv,
 				   const struct rtl8365mb_vlan4k *vlan4k)
 {
+	bool is_d = rtl8365mb_get_family(priv) == RTL8365MB_FAMILY_D;
+	size_t entry_size = is_d ? RTL8365MB_D_CVLAN_ENTRY_SIZE :
+				   RTL8365MB_CVLAN_ENTRY_SIZE;
 	u16 data[RTL8365MB_CVLAN_ENTRY_SIZE] = { 0 };
 	u16 vid;
 	int val;
@@ -244,36 +284,59 @@ static int rtl8365mb_vlan_4k_write(struct realtek_priv *priv,
 	val = FIELD_GET(RTL8365MB_CVLAN_UNTAG_LO_MASK, vlan4k->untag);
 	data[0] |= FIELD_PREP(RTL8365MB_CVLAN_ENTRY_D0_UNTAG_MASK, val);
 
-	data[1] |= FIELD_PREP(RTL8365MB_CVLAN_ENTRY_D1_FID_MASK, vlan4k->fid);
-	data[1] |= FIELD_PREP(RTL8365MB_CVLAN_ENTRY_D1_VBPEN_MASK,
-			      vlan4k->priority_en);
-	data[1] |= FIELD_PREP(RTL8365MB_CVLAN_ENTRY_D1_VBPRI_MASK,
-			      vlan4k->priority);
-	data[1] |= FIELD_PREP(RTL8365MB_CVLAN_ENTRY_D1_ENVLANPOL_MASK,
-			      vlan4k->policing_en);
-
-	/* FIELD_* does not play nice with struct bitfield. */
-	val = vlan4k->meteridx;
-	val = FIELD_GET(RTL8365MB_CVLAN_METERIDX_LO_MASK, val);
-	data[1] |= FIELD_PREP(RTL8365MB_CVLAN_ENTRY_D1_METERIDX_MASK, val);
-
-	data[1] |= FIELD_PREP(RTL8365MB_CVLAN_ENTRY_D1_IVL_SVL_MASK,
-			      vlan4k->ivl_en);
-
-	val = FIELD_GET(RTL8365MB_CVLAN_MBR_HI_MASK, vlan4k->member);
-	data[2] |= FIELD_PREP(RTL8365MB_CVLAN_ENTRY_D2_MBR_EXT_MASK, val);
-
-	val = FIELD_GET(RTL8365MB_CVLAN_UNTAG_HI_MASK, vlan4k->untag);
-	data[2] |= FIELD_PREP(RTL8365MB_CVLAN_ENTRY_D2_UNTAG_EXT_MASK, val);
-
-	val = vlan4k->meteridx;
-	val = FIELD_GET(RTL8365MB_CVLAN_METERIDX_HI_MASK, val);
-	data[2] |= FIELD_PREP(RTL8365MB_CVLAN_ENTRY_D2_METERIDX_EXT_MASK, val);
+	if (is_d) {
+		/* The chip supports both IVL and SVL, but the caller (see
+		 * rtl8365mb_vlan_4k_port_set()) never requests SVL, so both
+		 * IVL/SVL selector bits are forced here rather than threaded
+		 * through from vlan4k->ivl_en, which family C does honor.
+		 */
+		data[1] |= FIELD_PREP(RTL8365MB_D_CVLAN_ENTRY_D1_IVL_EN_MASK,
+				      1) |
+			   FIELD_PREP(RTL8365MB_D_CVLAN_ENTRY_D1_SVLAN_CHK_IVL_SVL_MASK,
+				      1);
+		data[1] |= FIELD_PREP(RTL8365MB_D_CVLAN_ENTRY_D1_FID_MASK,
+				      vlan4k->fid);
+		/* No priority/meter/member-untag-extension fields exist in
+		 * family D's 2-word entry - data[1] and data[0] above are
+		 * the whole entry, and data[2] is not part of it at all.
+		 */
+	} else {
+		val = vlan4k->fid;
+		data[1] |= FIELD_PREP(RTL8365MB_CVLAN_ENTRY_D1_FID_MASK, val);
+		data[1] |= FIELD_PREP(RTL8365MB_CVLAN_ENTRY_D1_VBPEN_MASK,
+				      vlan4k->priority_en);
+		data[1] |= FIELD_PREP(RTL8365MB_CVLAN_ENTRY_D1_VBPRI_MASK,
+				      vlan4k->priority);
+		data[1] |= FIELD_PREP(RTL8365MB_CVLAN_ENTRY_D1_ENVLANPOL_MASK,
+				      vlan4k->policing_en);
+
+		/* FIELD_* does not play nice with struct bitfield. */
+		val = vlan4k->meteridx;
+		val = FIELD_GET(RTL8365MB_CVLAN_METERIDX_LO_MASK, val);
+		data[1] |= FIELD_PREP(RTL8365MB_CVLAN_ENTRY_D1_METERIDX_MASK,
+				      val);
+
+		data[1] |= FIELD_PREP(RTL8365MB_CVLAN_ENTRY_D1_IVL_SVL_MASK,
+				      vlan4k->ivl_en);
+
+		val = FIELD_GET(RTL8365MB_CVLAN_MBR_HI_MASK, vlan4k->member);
+		data[2] |= FIELD_PREP(RTL8365MB_CVLAN_ENTRY_D2_MBR_EXT_MASK,
+				      val);
+
+		val = FIELD_GET(RTL8365MB_CVLAN_UNTAG_HI_MASK, vlan4k->untag);
+		data[2] |= FIELD_PREP(RTL8365MB_CVLAN_ENTRY_D2_UNTAG_EXT_MASK,
+				      val);
+
+		val = vlan4k->meteridx;
+		val = FIELD_GET(RTL8365MB_CVLAN_METERIDX_HI_MASK, val);
+		data[2] |= FIELD_PREP(RTL8365MB_CVLAN_ENTRY_D2_METERIDX_EXT_MASK,
+				      val);
+	}
 
 	vid = vlan4k->vid;
 	return rtl8365mb_table_query(priv, RTL8365MB_TABLE_CVLAN,
 				     RTL8365MB_TABLE_OP_WRITE, &vid, 0, 0,
-				     data, ARRAY_SIZE(data));
+				     data, entry_size);
 }
 
 static int
-- 
2.53.0

[PATCH net-next v3 6/9] net: dsa: realtek: rtl8365mb: use raw VID for PVID on family D

[Mieczyslaw Nalewaj]

Family D has no working VLAN member config (MC) table. Its PVID is a
raw 12-bit VID in a per-port register at 0x0700 + port, whereas family C
stores a 5-bit MC table index, two ports per register, at
0x0700 + (port >> 1).

Running the family C code on family D therefore reads an MC table that
does not exist, and writes an MC index into the VID register of port
(port >> 1) instead of the one of the port being configured.

Read the PVID straight from its register in
rtl8365mb_vlan_port_get_pvid(), and make rtl8365mb_vlan_pvid_port_set()
and rtl8365mb_vlan_pvid_port_clear() use direct-VID variants on family D
that skip the MC table. They keep the family C frame filter handling and
rollback on error.

No functional change for family C.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
---
 drivers/net/dsa/realtek/rtl8365mb_vlan.c | 181 ++++++++++++++++++++++-
 1 file changed, 176 insertions(+), 5 deletions(-)

diff --git a/drivers/net/dsa/realtek/rtl8365mb_vlan.c b/drivers/net/dsa/realtek/rtl8365mb_vlan.c
index 2c4c5ba..ccfa764 100644
--- a/drivers/net/dsa/realtek/rtl8365mb_vlan.c
+++ b/drivers/net/dsa/realtek/rtl8365mb_vlan.c
@@ -44,6 +44,10 @@
  *
  * VLANMC index 0 is reserved as a neutral PVID, used for standalone ports.
  *
+ * Everything above describes chips that have a VLAN membership configuration
+ * table. RTL8365MB_FAMILY_D chips do not have one: their PVID is a raw 12-bit
+ * VID in a per-port register, and no VLANMC entries are allocated.
+ *
  */
 
 #include "rtl8365mb_vlan.h"
@@ -119,6 +123,11 @@
 #define   RTL8365MB_VLAN_PVID_CTRL_PORT_MCIDX_MASK(_p) \
 		(0x1F << RTL8365MB_VLAN_PVID_CTRL_PORT_MCIDX_OFFSET(_p))
 
+#define RTL8365MB_D_VLAN_PVID_CTRL_BASE			0x0700
+#define RTL8365MB_D_VLAN_PVID_CTRL_REG(port) \
+	(RTL8365MB_D_VLAN_PVID_CTRL_BASE + (port))
+#define RTL8365MB_D_VLAN_PVID_CTRL_MASK			GENMASK(11, 0)
+
 /* Frame type filtering registers */
 #define RTL8365MB_VLAN_ACCEPT_FRAME_TYPE_BASE	0x07aa
 #define RTL8365MB_VLAN_ACCEPT_FRAME_TYPE_REG(port) \
@@ -170,7 +179,7 @@ struct rtl8365mb_vlan4k {
  * This structure is used to get/set entries in the VLAN membership
  * configuration database. This feature is largely vestigial, but
  * still needed for at least the following features:
- *   - PVID configuration
+ *   - PVID configuration (family C only, family D has no VLAN MC table)
  *   - ACL configuration
  *   - selection of VLAN by the CPU tag when VSEL=1, although the switch
  *     can also select VLAN based on the VLAN tag if VSEL=0
@@ -742,11 +751,25 @@ int rtl8365mb_vlan_port_get_pvid(struct realtek_priv *priv, int port, u16 *pvid)
 	u8 vlanmc_idx;
 	int ret;
 
-	ret = rtl8365mb_vlan_get_pvid_mc(priv, port, &vlanmc_idx, &vlanmc);
-	if (ret)
-		return ret;
+	if (rtl8365mb_get_family(priv) == RTL8365MB_FAMILY_D) {
+		u32 data;
+
+		ret = regmap_read(priv->map,
+				  RTL8365MB_D_VLAN_PVID_CTRL_REG(port),
+				  &data);
+		if (ret)
+			return ret;
+
+		*pvid = data & RTL8365MB_D_VLAN_PVID_CTRL_MASK;
+	} else {
+		ret = rtl8365mb_vlan_get_pvid_mc(priv, port, &vlanmc_idx,
+						 &vlanmc);
+		if (ret)
+			return ret;
+
+		*pvid = vlanmc.evid;
+	}
 
-	*pvid = vlanmc.evid;
 	return 0;
 }
 
@@ -811,6 +834,68 @@ rtl8365mb_vlan_port_set_framefilter(struct realtek_priv *priv,
 				  val);
 }
 
+/*
+ * rtl8365mb_vlan_pvid_port_set_direct() - Configure a port's PVID as a raw
+ * VID written to its dedicated register, for chip families without a
+ * working VLAN MC table (RTL8365MB_FAMILY_D)
+ *
+ * Reads back the previous PVID and frame filter first so both can be
+ * restored if enabling the new PVID fails partway through, matching
+ * the rollback behavior of the family-C implementation below.
+ *
+ * Context: Can sleep. Must be called with &priv->vlan_lock held.
+ * Return: 0 on success, or a negative error code on failure.
+ */
+static int rtl8365mb_vlan_pvid_port_set_direct(struct realtek_priv *priv,
+					       int port, u16 vid)
+{
+	enum rtl8365mb_frame_ingress prev_accepted_frame;
+	u32 prev_pvid;
+	int ret;
+
+	ret = regmap_read(priv->map, RTL8365MB_D_VLAN_PVID_CTRL_REG(port),
+			  &prev_pvid);
+	if (ret) {
+		dev_err(priv->dev, "Failed to read current PVID\n");
+		return ret;
+	}
+	prev_pvid &= RTL8365MB_D_VLAN_PVID_CTRL_MASK;
+
+	ret = rtl8365mb_vlan_port_get_framefilter(priv, port,
+						  &prev_accepted_frame);
+	if (ret) {
+		dev_err(priv->dev, "Failed to get current framefilter\n");
+		return ret;
+	}
+
+	ret = regmap_update_bits(priv->map,
+				 RTL8365MB_D_VLAN_PVID_CTRL_REG(port),
+				 RTL8365MB_D_VLAN_PVID_CTRL_MASK,
+				 vid & RTL8365MB_D_VLAN_PVID_CTRL_MASK);
+	if (ret) {
+		dev_err(priv->dev, "Failed to set port PVID\n");
+		return ret;
+	}
+
+	/* Changing accept frame is what enables PVID (if not enabled before) */
+	ret = rtl8365mb_vlan_port_set_framefilter(priv, port,
+						  RTL8365MB_FRAME_TYPE_ANY_FRAME);
+	if (ret) {
+		dev_err(priv->dev, "Failed to set port frame filter\n");
+		goto undo_pvid_write;
+	}
+
+	return 0;
+
+undo_pvid_write:
+	(void)regmap_update_bits(priv->map,
+				 RTL8365MB_D_VLAN_PVID_CTRL_REG(port),
+				 RTL8365MB_D_VLAN_PVID_CTRL_MASK, prev_pvid);
+	(void)rtl8365mb_vlan_port_set_framefilter(priv, port,
+						  prev_accepted_frame);
+	return ret;
+}
+
 /*
  * rtl8365mb_vlan_pvid_port_set() - Configure a port's PVID and associated
  * VLANMC entry
@@ -823,6 +908,9 @@ rtl8365mb_vlan_port_set_framefilter(struct realtek_priv *priv,
  * PVID. Gracefully unwinds and restores previous configuration if a hardware
  * write operation fails during execution.
  *
+ * On RTL8365MB_FAMILY_D there is no VLANMC table: the VID is written directly
+ * to the port's PVID register and no VLANMC entry is allocated.
+ *
  * Context: Can sleep. Must be called with &priv->vlan_lock held.
  * Takes and releases &priv->map_lock.
  * Return: 0 on success, or a negative error code on failure.
@@ -840,6 +928,13 @@ int rtl8365mb_vlan_pvid_port_set(struct dsa_switch *ds, int port, u16 vid,
 
 	lockdep_assert_held(&priv->vlan_lock);
 
+	/* This chip family has no VLAN MC table - PVID is a raw VID in a
+	 * dedicated per-port register, and there is no separate membership
+	 * table entry to allocate/track.
+	 */
+	if (rtl8365mb_get_family(priv) == RTL8365MB_FAMILY_D)
+		return rtl8365mb_vlan_pvid_port_set_direct(priv, port, vid);
+
 	/* Read the old PVID exclusively to undo in case of error */
 	ret = rtl8365mb_vlan_get_pvid_mc(priv, port, &prev_vlanmc_idx,
 					 &prev_vlanmc);
@@ -919,6 +1014,76 @@ undo_vlan_mc_port_set:
 	return ret;
 }
 
+/*
+ * rtl8365mb_vlan_pvid_port_clear_direct() - Remove a port's raw-VID PVID
+ * configuration, for chip families without a working VLAN MC table
+ * (RTL8365MB_FAMILY_D)
+ *
+ * Reads back the previous frame filter first so it can be restored if
+ * clearing the PVID register fails.
+ *
+ * Context: Can sleep. Must be called with &priv->vlan_lock held.
+ * Return: 0 on success, or a negative error code on failure.
+ */
+static int rtl8365mb_vlan_pvid_port_clear_direct(struct dsa_switch *ds,
+						 int port, u16 vid)
+{
+	enum rtl8365mb_frame_ingress prev_accepted_frame;
+	struct realtek_priv *priv = ds->priv;
+	bool filtering;
+	u32 cur_pvid;
+	int ret;
+
+	ret = regmap_read(priv->map, RTL8365MB_D_VLAN_PVID_CTRL_REG(port),
+			  &cur_pvid);
+	if (ret) {
+		dev_err(priv->dev, "Failed to read current PVID\n");
+		return ret;
+	}
+
+	/* Port is not using this VID as PVID. Nothing to remove. */
+	if ((cur_pvid & RTL8365MB_D_VLAN_PVID_CTRL_MASK) != vid)
+		return 0;
+
+	filtering = dsa_port_is_vlan_filtering(dsa_to_port(ds, port));
+
+	/* Changing accept frame is what really removes PVID. But only do
+	 * that if VLAN filtering is enabled.
+	 */
+	if (filtering) {
+		ret = rtl8365mb_vlan_port_get_framefilter(priv, port,
+							  &prev_accepted_frame);
+		if (ret) {
+			dev_err(priv->dev,
+				"Failed to get current framefilter\n");
+			return ret;
+		}
+
+		ret = rtl8365mb_vlan_port_set_framefilter(
+			priv, port, RTL8365MB_FRAME_TYPE_TAGGED_ONLY);
+		if (ret) {
+			dev_err(priv->dev, "Failed to set port frame filter\n");
+			return ret;
+		}
+	}
+
+	ret = regmap_update_bits(priv->map,
+				 RTL8365MB_D_VLAN_PVID_CTRL_REG(port),
+				 RTL8365MB_D_VLAN_PVID_CTRL_MASK, 0);
+	if (ret) {
+		dev_err(priv->dev, "Failed to set port PVID to 0\n");
+		goto undo_set_framefilter;
+	}
+
+	return 0;
+
+undo_set_framefilter:
+	if (filtering)
+		(void)rtl8365mb_vlan_port_set_framefilter(priv, port,
+							  prev_accepted_frame);
+	return ret;
+}
+
 /*
  * rtl8365mb_vlan_pvid_port_clear() - Remove a port's PVID configuration
  * @ds: dsa switch instance
@@ -928,6 +1093,9 @@ undo_vlan_mc_port_set:
  * Resets the target port's hardware PVID allocation to 0. Cleans up and frees
  * the associated VLANMC entry if no other ports are referencing it.
  *
+ * On RTL8365MB_FAMILY_D the port's PVID register is reset to 0 directly; there
+ * is no VLANMC entry to free.
+ *
  * Context: Can sleep. Must be called with &priv->vlan_lock held.
  * Takes and releases &priv->map_lock.
  * Return: 0 on success, or a negative error code on failure.
@@ -942,6 +1110,9 @@ int rtl8365mb_vlan_pvid_port_clear(struct dsa_switch *ds, int port, u16 vid)
 
 	lockdep_assert_held(&priv->vlan_lock);
 
+	if (rtl8365mb_get_family(priv) == RTL8365MB_FAMILY_D)
+		return rtl8365mb_vlan_pvid_port_clear_direct(ds, port, vid);
+
 	ret = rtl8365mb_vlan_get_pvid_mc(priv, port, &vlanmc_idx,
 					 &vlanmc);
 	if (ret) {
-- 
2.53.0

[PATCH net-next v3 7/9] net: dsa: realtek: rtl8365mb: add family D SDS13 PCS support

[Mieczyslaw Nalewaj]

Extend the existing RTL8367S SGMII/HSGMII PCS implementation in this
driver for family D switches, whose CPU SerDes is reached through the
indexed SDS13 window and whose SDS_MISC fields differ from family C.

The register sequence and tuning tables are derived from the GPL-licensed
Realtek RTL8367D port API distributed in the Mercusys MR80X GPL release.
Keep the existing family C path unchanged and select the new behavior from
the driver's chip-family metadata, making the implementation reusable by
other family D boards.

Co-developed-by: Fabiano Tassotti <fabianotassotti@gmail.com>
Signed-off-by: Fabiano Tassotti <fabianotassotti@gmail.com>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
---
 drivers/net/dsa/realtek/rtl8365mb_main.c | 181 ++++++++++++++++++-----
 1 file changed, 145 insertions(+), 36 deletions(-)

diff --git a/drivers/net/dsa/realtek/rtl8365mb_main.c b/drivers/net/dsa/realtek/rtl8365mb_main.c
index c15b88b..0d3a2a3 100644
--- a/drivers/net/dsa/realtek/rtl8365mb_main.c
+++ b/drivers/net/dsa/realtek/rtl8365mb_main.c
@@ -284,6 +284,7 @@
 #define   RTL8365MB_SDS_INDACS_CMD_BUSY_MASK	BIT(8)
 #define   RTL8365MB_SDS_INDACS_CMD_RUN_MASK	BIT(7)
 #define   RTL8365MB_SDS_INDACS_CMD_WR_MASK	BIT(6)
+#define   RTL8365MB_SDS_INDACS_CMD_INDEX_MASK	GENMASK(5, 0)
 #define RTL8365MB_SDS_INDACS_ADR_REG		0x6601
 #define RTL8365MB_SDS_INDACS_DATA_REG		0x6602
 
@@ -332,7 +333,22 @@
 #define   RTL8365MB_SDS_OPTION_ARM_KEY		0x0249
 #define RTL8365MB_SDS_OPTION_REG		0x13C1
 
+/* Family D uses the SDS13 indirect window for its MAC6 SerDes. */
+#define RTL8365MB_D_SDS_EXT0_INDEX			13
+#define RTL8365MB_D_FIBER_CFG2_REG			0x13E8
+#define   RTL8365MB_D_FIBER_CFG2_RX_DISABLE_MASK	GENMASK(7, 6)
+#define   RTL8365MB_D_FIBER_CFG2_RX_DISABLE_SDS0	BIT(6)
+#define RTL8365MB_D_SDS_MISC_PA33PC_EN			BIT(11)
+#define RTL8365MB_D_SDS_MISC_PA12PC_EN			BIT(10)
+#define RTL8365MB_D_SDS_MISC_MAC6_SEL_SDS0		BIT(9)
 #define RTL8365MB_D_SDS_MISC_MODE_FIELD_MASK		GENMASK(4, 0)
+#define RTL8365MB_D_SDS_MISC_MODE_SGMII			0x02
+#define RTL8365MB_D_SDS_MISC_MODE_HSGMII		0x12
+#define RTL8365MB_D_SDS_MISC_CFG_MASK			\
+	(RTL8365MB_D_SDS_MISC_PA33PC_EN |		\
+	 RTL8365MB_D_SDS_MISC_PA12PC_EN |		\
+	 RTL8365MB_D_SDS_MISC_MAC6_SEL_SDS0 |		\
+	 RTL8365MB_D_SDS_MISC_MODE_FIELD_MASK)
 /* Shared "disable" encoding for both SDS_MISC's and SDS1_MISC0's
  * 5-bit mode fields.
  */
@@ -713,6 +729,21 @@ static const struct rtl8365mb_jam_tbl_entry rtl8365mb_sds_jam_hsgmii[] = {
 	{ 0x0424, 0xD810 }, { 0x0001, 0x0F80 }, { 0x002E, 0x83F2 },
 };
 
+/* Family D tuning tables from the Realtek vendor port API. */
+static const struct rtl8365mb_jam_tbl_entry rtl8365mb_d_sds_jam_sgmii[] = {
+	{ 0x0427, 0x4E0C }, { 0x0428, 0xAA00 }, { 0x0425, 0x5189 },
+	{ 0x0424, 0x8414 }, { 0x0423, 0x1020 }, { 0x0410, 0x0002 },
+	{ 0x0484, 0x011B }, { 0x0421, 0x8E13 }, { 0x0422, 0x1140 },
+	{ 0x0004, 0x074F },
+};
+
+static const struct rtl8365mb_jam_tbl_entry rtl8365mb_d_sds_jam_hsgmii[] = {
+	{ 0x0427, 0x4E0C }, { 0x0428, 0xAA00 }, { 0x0425, 0x5189 },
+	{ 0x0424, 0x8414 }, { 0x0423, 0x1020 }, { 0x0410, 0x0002 },
+	{ 0x0504, 0x051B }, { 0x0421, 0x8E13 }, { 0x0422, 0x1140 },
+	{ 0x0004, 0x074F },
+};
+
 enum rtl8365mb_phy_interface_mode {
 	RTL8365MB_PHY_INTERFACE_MODE_INVAL = 0,
 	RTL8365MB_PHY_INTERFACE_MODE_INTERNAL = BIT(0),
@@ -1316,7 +1347,8 @@ static int rtl8365mb_ext_config_rgmii(struct realtek_priv *priv, int port,
 	return 0;
 }
 
-static int rtl8365mb_sds_write(struct realtek_priv *priv, u16 addr, u16 data)
+static int rtl8365mb_sds_write(struct realtek_priv *priv, u8 index,
+			       u16 addr, u16 data)
 {
 	int ret;
 
@@ -1334,10 +1366,13 @@ static int rtl8365mb_sds_write(struct realtek_priv *priv, u16 addr, u16 data)
 	 */
 	return regmap_write(priv->map, RTL8365MB_SDS_INDACS_CMD_REG,
 			    RTL8365MB_SDS_INDACS_CMD_RUN_MASK |
-			    RTL8365MB_SDS_INDACS_CMD_WR_MASK);
+			    RTL8365MB_SDS_INDACS_CMD_WR_MASK |
+			    FIELD_PREP(RTL8365MB_SDS_INDACS_CMD_INDEX_MASK,
+				       index));
 }
 
-static int rtl8365mb_sds_read(struct realtek_priv *priv, u16 addr, u16 *data)
+static int rtl8365mb_sds_read(struct realtek_priv *priv, u8 index,
+			      u16 addr, u16 *data)
 {
 	u32 val;
 	int ret;
@@ -1347,7 +1382,9 @@ static int rtl8365mb_sds_read(struct realtek_priv *priv, u16 addr, u16 *data)
 		return ret;
 
 	ret = regmap_write(priv->map, RTL8365MB_SDS_INDACS_CMD_REG,
-			   RTL8365MB_SDS_INDACS_CMD_RUN_MASK);
+			   RTL8365MB_SDS_INDACS_CMD_RUN_MASK |
+			   FIELD_PREP(RTL8365MB_SDS_INDACS_CMD_INDEX_MASK,
+				      index));
 	if (ret)
 		return ret;
 
@@ -1387,6 +1424,14 @@ static int rtl8365mb_sds_probe_option(struct realtek_priv *priv)
 	int ret;
 	int i;
 
+	/* Family D has a fixed SDS13 programming model and does not use the
+	 * family C option register to select its tuning table.
+	 */
+	if (rtl8365mb_get_family(priv) == RTL8365MB_FAMILY_D) {
+		mb->sds_supported = true;
+		return 0;
+	}
+
 	/* Nothing to probe if no external interface is wired to the SerDes */
 	for (i = 0; i < RTL8365MB_MAX_NUM_EXTINTS; i++) {
 		extint = &mb->chip_info->extints[i];
@@ -1465,28 +1510,47 @@ static int rtl8365mb_pcs_config(struct phylink_pcs *pcs, unsigned int neg_mode,
 				const unsigned long *advertising,
 				bool permit_pause_to_mac)
 {
-	const struct rtl8365mb_jam_tbl_entry *sds_jam;
 	const int id = RTL8365MB_SDS_EXT_INTERFACE_ID;
+	const struct rtl8365mb_jam_tbl_entry *sds_jam;
 	struct rtl8365mb *mb = pcs_to_rtl8365mb(pcs);
-	struct realtek_priv *priv;
+	struct realtek_priv *priv = mb->priv;
 	size_t sds_jam_size;
-	u32 mode;
+	u32 misc_mask;
+	u32 misc_val;
+	u32 sds_mode;
+	u8 sds_index;
+	bool is_d;
 	u16 val;
 	int ret;
 	int i;
 
-	priv = mb->priv;
+	is_d = rtl8365mb_get_family(priv) == RTL8365MB_FAMILY_D;
 
+	/* Select the appropriate tuning table and SDS mode */
 	if (interface == PHY_INTERFACE_MODE_2500BASEX) {
-		sds_jam = rtl8365mb_sds_jam_hsgmii;
-		sds_jam_size = ARRAY_SIZE(rtl8365mb_sds_jam_hsgmii);
-		mode = RTL8365MB_EXT_PORT_MODE_HSGMII;
+		if (is_d) {
+			sds_jam = rtl8365mb_d_sds_jam_hsgmii;
+			sds_jam_size = ARRAY_SIZE(rtl8365mb_d_sds_jam_hsgmii);
+			sds_mode = RTL8365MB_D_SDS_MISC_MODE_HSGMII;
+		} else {
+			sds_jam = rtl8365mb_sds_jam_hsgmii;
+			sds_jam_size = ARRAY_SIZE(rtl8365mb_sds_jam_hsgmii);
+			sds_mode = RTL8365MB_EXT_PORT_MODE_HSGMII;
+		}
 	} else {
-		sds_jam = rtl8365mb_sds_jam_sgmii;
-		sds_jam_size = ARRAY_SIZE(rtl8365mb_sds_jam_sgmii);
-		mode = RTL8365MB_EXT_PORT_MODE_SGMII;
+		if (is_d) {
+			sds_jam = rtl8365mb_d_sds_jam_sgmii;
+			sds_jam_size = ARRAY_SIZE(rtl8365mb_d_sds_jam_sgmii);
+			sds_mode = RTL8365MB_D_SDS_MISC_MODE_SGMII;
+		} else {
+			sds_jam = rtl8365mb_sds_jam_sgmii;
+			sds_jam_size = ARRAY_SIZE(rtl8365mb_sds_jam_sgmii);
+			sds_mode = RTL8365MB_EXT_PORT_MODE_SGMII;
+		}
 	}
 
+	sds_index = is_d ? RTL8365MB_D_SDS_EXT0_INDEX : 0;
+
 	/* Hold the embedded DW8051 microcontroller in reset and keep it
 	 * disabled. The vendor driver loads firmware into it to manage the
 	 * SerDes link, but the firmware only duplicates work that phylink
@@ -1515,34 +1579,53 @@ static int rtl8365mb_pcs_config(struct phylink_pcs *pcs, unsigned int neg_mode,
 
 	/* Tune the SerDes with vendor-prescribed parameters */
 	for (i = 0; i < sds_jam_size; i++) {
-		ret = rtl8365mb_sds_write(priv, sds_jam[i].reg,
-					  sds_jam[i].val);
+		ret = rtl8365mb_sds_write(priv, sds_index,
+					  sds_jam[i].reg, sds_jam[i].val);
 		if (ret)
 			return ret;
 	}
 
-	/* Mux the SerDes to MAC8 in the requested mode */
+	/* Family-specific post-tuning configuration */
+	if (is_d) {
+		ret = regmap_update_bits(priv->map, RTL8365MB_D_FIBER_CFG2_REG,
+					 RTL8365MB_D_FIBER_CFG2_RX_DISABLE_MASK,
+					 RTL8365MB_D_FIBER_CFG2_RX_DISABLE_SDS0);
+		if (ret)
+			return ret;
+
+		misc_mask = RTL8365MB_D_SDS_MISC_CFG_MASK;
+		misc_val  = RTL8365MB_D_SDS_MISC_PA33PC_EN |
+			    RTL8365MB_D_SDS_MISC_PA12PC_EN |
+			    RTL8365MB_D_SDS_MISC_MAC6_SEL_SDS0 | sds_mode;
+	} else {
+		/* Mux the SerDes to MAC8 in the requested mode */
+		misc_mask = RTL8365MB_SDS_MISC_MAC8_SEL_SGMII_MASK |
+			    RTL8365MB_SDS_MISC_MAC8_SEL_HSGMII_MASK;
+		misc_val  = (sds_mode == RTL8365MB_EXT_PORT_MODE_SGMII) ?
+			    RTL8365MB_SDS_MISC_MAC8_SEL_SGMII_MASK :
+			    RTL8365MB_SDS_MISC_MAC8_SEL_HSGMII_MASK;
+	}
+
 	ret = regmap_update_bits(priv->map, RTL8365MB_SDS_MISC_REG,
-				 RTL8365MB_SDS_MISC_MAC8_SEL_SGMII_MASK |
-					 RTL8365MB_SDS_MISC_MAC8_SEL_HSGMII_MASK,
-				 mode == RTL8365MB_EXT_PORT_MODE_SGMII ?
-					 RTL8365MB_SDS_MISC_MAC8_SEL_SGMII_MASK :
-					 RTL8365MB_SDS_MISC_MAC8_SEL_HSGMII_MASK);
+				 misc_mask, misc_val);
 	if (ret)
 		return ret;
 
-	val = mode << RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_OFFSET(id);
-	ret = regmap_update_bits(priv->map,
-				 RTL8365MB_DIGITAL_INTERFACE_SELECT_REG(id),
-				 RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_MASK(id),
-				 val);
-	if (ret)
-		return ret;
+	if (!is_d) {
+		val = sds_mode << RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_OFFSET(id);
+		ret = regmap_update_bits(priv->map,
+					 RTL8365MB_DIGITAL_INTERFACE_SELECT_REG(id),
+					 RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_MASK(id),
+					 val);
+		if (ret)
+			return ret;
+	}
 
 	/* Take the SerDes out of reset. The vendor driver does this only
 	 * after the SerDes mux and the interface mode are configured.
 	 */
-	ret = rtl8365mb_sds_write(priv, RTL8365MB_SDS_REG_RESET,
+	ret = rtl8365mb_sds_write(priv, sds_index,
+				  RTL8365MB_SDS_REG_RESET,
 				  RTL8365MB_SDS_RESET_DEASSERT);
 	if (ret)
 		return ret;
@@ -1552,12 +1635,14 @@ static int rtl8365mb_pcs_config(struct phylink_pcs *pcs, unsigned int neg_mode,
 	 * This flushes the FIFOs and ensures a clean state for the link,
 	 * preventing silent drops and CRC errors.
 	 */
-	ret = rtl8365mb_sds_write(priv, RTL8365MB_SDS_REG_BMCR,
+	ret = rtl8365mb_sds_write(priv, sds_index,
+				  RTL8365MB_SDS_REG_BMCR,
 				  RTL8365MB_SDS_BMCR_DPRST_PHASE1);
 	if (ret)
 		return ret;
 
-	ret = rtl8365mb_sds_write(priv, RTL8365MB_SDS_REG_BMCR,
+	ret = rtl8365mb_sds_write(priv, sds_index,
+				  RTL8365MB_SDS_REG_BMCR,
 				  RTL8365MB_SDS_BMCR_DPRST_PHASE2);
 	if (ret)
 		return ret;
@@ -1565,14 +1650,16 @@ static int rtl8365mb_pcs_config(struct phylink_pcs *pcs, unsigned int neg_mode,
 	/* Keep SGMII in-band autonegotiation disabled: the link parameters are
 	 * forced from rtl8365mb_pcs_link_up() instead.
 	 */
-	ret = rtl8365mb_sds_read(priv, RTL8365MB_SDS_REG_NWAY, &val);
+	ret = rtl8365mb_sds_read(priv, sds_index,
+				 RTL8365MB_SDS_REG_NWAY, &val);
 	if (ret)
 		return ret;
 
 	val &= ~RTL8365MB_SDS_NWAY_EN_MASK;
 	val |= RTL8365MB_SDS_NWAY_RESTART_MASK;
 
-	return rtl8365mb_sds_write(priv, RTL8365MB_SDS_REG_NWAY, val);
+	return rtl8365mb_sds_write(priv, sds_index,
+				   RTL8365MB_SDS_REG_NWAY, val);
 }
 
 static bool rtl8365mb_interface_is_serdes(phy_interface_t interface)
@@ -1597,10 +1684,14 @@ static void rtl8365mb_pcs_get_state(struct phylink_pcs *pcs,
 {
 	struct rtl8365mb *mb = pcs_to_rtl8365mb(pcs);
 	struct realtek_priv *priv = mb->priv;
+	u8 sds_index = 0;
 	u16 status;
+	bool is_d;
 	u32 val;
 	int ret;
 
+	is_d = rtl8365mb_get_family(priv) == RTL8365MB_FAMILY_D;
+
 	/* In-band autonegotiation is not implemented, so the link parameters are
 	 * forced from rtl8365mb_pcs_link_up(). The real link state must still be
 	 * read from the SerDes itself: the embedded DW8051 microcontroller that
@@ -1608,7 +1699,11 @@ static void rtl8365mb_pcs_get_state(struct phylink_pcs *pcs,
 	 * rtl8365mb_pcs_config()), so the link status register can be read
 	 * directly through the SDS_INDACS window without racing the auto-poll.
 	 */
-	ret = rtl8365mb_sds_read(priv, RTL8365MB_SDS_REG_LINK_STATUS, &status);
+	if (is_d)
+		sds_index = RTL8365MB_D_SDS_EXT0_INDEX;
+
+	ret = rtl8365mb_sds_read(priv, sds_index,
+				 RTL8365MB_SDS_REG_LINK_STATUS, &status);
 	if (ret) {
 		state->link = false;
 		return;
@@ -1619,6 +1714,13 @@ static void rtl8365mb_pcs_get_state(struct phylink_pcs *pcs,
 	if (!state->link)
 		return;
 
+	if (is_d) {
+		state->duplex = DUPLEX_FULL;
+		state->speed = state->interface == PHY_INTERFACE_MODE_2500BASEX ?
+				SPEED_2500 : SPEED_1000;
+		return;
+	}
+
 	/* The speed and duplex are forced; read them back from the values
 	 * programmed into the SerDes MISC register.
 	 */
@@ -1660,6 +1762,12 @@ static void rtl8365mb_pcs_link_up(struct phylink_pcs *pcs,
 	u32 r_speed;
 	int ret;
 
+	/* Family D forces the external MAC ability from mac_link_up(); its
+	 * SDS_MISC fields do not share the family C link-force layout.
+	 */
+	if (rtl8365mb_get_family(priv) == RTL8365MB_FAMILY_D)
+		return;
+
 	/* The speed field has no value for 2.5 Gbps: the rate is determined by
 	 * the HSGMII SerDes configuration, and the vendor driver programs the
 	 * 1 Gbps value here.
@@ -1989,7 +2097,8 @@ static void rtl8365mb_phylink_mac_link_up(struct phylink_config *config,
 		 * rtl8365mb_pcs_link_up() because pcs_link_up() carries no
 		 * pause information.
 		 */
-		if (rtl8365mb_interface_is_serdes(interface)) {
+		if (rtl8365mb_interface_is_serdes(interface) &&
+		    rtl8365mb_get_family(priv) != RTL8365MB_FAMILY_D) {
 			u32 val = 0;
 
 			if (tx_pause)
-- 
2.53.0

[PATCH net-next v3 8/9] net: dsa: realtek: rtl8365mb: re-latch the family D SerDes

[Mieczyslaw Nalewaj]

The family D receiver latches on the DISABLE -> HSGMII edge in SDS_MISC
rather than on the value, and it will not latch until the MAC at the
other end of the trunk has brought its own half of the link up. If it
does not latch, the trunk reports 2.5Gbps/Full on both sides but moves
no frames: the CPU MAC transmits, the switch CPU port counts no octets,
and there are no CRC, alignment or FIFO errors.

The two ends can be seconds apart, e.g. on an IPQ5018 board:

  5.27  rtl8365mb: configuring for fixed/2500base-x   <- pcs_config()
  7.72  ipq5018-gmac-dwmac eth0: configuring for fixed/2500base-x
  8.02  ipq5018-gmac-dwmac eth0: Link is Up - 2.5Gbps/Full
  8.56  SerDes latches

pcs_config() runs seconds before the far-end MAC even starts
configuring, so a single edge driven from there is not enough: the
receiver has nothing to latch onto yet. Neither is pcs_link_up(),
which is seconds early for the same reason. phylink does not help
either - it never calls rtl8365mb_pcs_get_state() for this port in
the first place, since mb->pcs.poll only arms phylink's own poll for
in-band links, and this CPU port is a fixed link.

There is no local signal that predicts when the far-end MAC will
bring up its half of the link (bit 8 of the SDS link-status word
does not change ahead of it), so the work cannot wait for it; it can
only tell afterwards, from the link-status bit, whether an edge took.
Nothing external re-checks this later. So pcs_config() kicks off one
attempt, and the work re-arms itself after each edge; the next run
checks whether the edge took, rather than waiting on a poll that will
not come.

Each attempt (park for 20 ms, then restore the target mode) is
performed by a work item rather than from pcs_config(), because the
attempts have to continue for seconds after pcs_config() has returned.
pcs_config() re-runs cancel the work, so an attempt never interleaves
with a reconfiguration. Before parking, the work reads the link status
itself and does not park if the receiver has already latched, since the
condition that queued it may be stale by the time it runs; it then ends
the episode instead.

Attempts are spaced about 1 s apart and capped at
RTL8365MB_D_SDS_RELATCH_MAX_TRIES (15) per fast episode. After the last
attempt one more run checks whether it took and only then warns that
the SerDes did not latch. The work then keeps driving one edge per
RTL8365MB_D_SDS_HEALTHCHECK_INTERVAL, so a far end that comes up late
or a link that drops again is recovered without a reconfiguration,
at a bounded cost of one 20 ms park per interval.

Once the receiver has latched, the work keeps checking the link every
10 s (RTL8365MB_D_SDS_HEALTHCHECK_INTERVAL). If it finds the link down
outside a reconfiguration, e.g. after the far end reset its PLL, it
logs that and starts a new episode. An episode also starts at every
pcs_config().

For family D, pcs_config() keeps the masked update of SDS_MISC and saves
the value it wrote as the target the work restores. The work parks and
restores with masked updates over the same fields, so other bits are
never touched.

The work reads the SerDes link status through the SDS_INDACS indirect
access window, a multi-register ADR/CMD/DATA sequence that the PCS
callbacks also use, so those sequences are serialized by a new sds_lock.
The SDS_MISC updates need no extra locking: each one is a single regmap
read-modify-write.

The work is only started for 2500base-x, the mode the re-latch edge
was observed with. It is cancelled from pcs_disable(), from
pcs_config() before SDS_MISC is touched, from teardown(), and by a
devres action, so that it never outlives the PCS or the driver data.

Co-developed-by: Oleg Gavrilov <gabonpivovich@gmail.com>
Signed-off-by: Oleg Gavrilov <gabonpivovich@gmail.com>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
---
 drivers/net/dsa/realtek/rtl8365mb_main.c | 264 +++++++++++++++++++++--
 1 file changed, 249 insertions(+), 15 deletions(-)

diff --git a/drivers/net/dsa/realtek/rtl8365mb_main.c b/drivers/net/dsa/realtek/rtl8365mb_main.c
index 0d3a2a3..5d80409 100644
--- a/drivers/net/dsa/realtek/rtl8365mb_main.c
+++ b/drivers/net/dsa/realtek/rtl8365mb_main.c
@@ -97,6 +97,7 @@
 #include <linux/irqdomain.h>
 #include <linux/mii.h>
 #include <linux/mutex.h>
+#include <linux/workqueue.h>
 #include <linux/of_irq.h>
 #include <linux/regmap.h>
 #include <linux/if_bridge.h>
@@ -298,6 +299,28 @@
 #define   RTL8365MB_SDS_MISC_SGMII_SPD_MASK		GENMASK(8, 7)
 #define   RTL8365MB_SDS_MISC_MAC8_SEL_SGMII_MASK	BIT(6)
 
+/* Re-latch retry interval and attempt budget. Each attempt parks the
+ * SerDes for 20 ms, so a far end that never comes up must not be retried
+ * at this rate forever, and the interval must not be so tight that
+ * back-to-back parks starve a link that is about to latch. The count is
+ * reset to 1 by pcs_config() and to 0 whenever the receiver latches;
+ * attempts start at pcs_config(), well before the far end MAC is up, so
+ * with the interval below the budget is roughly RELATCH_MAX_TRIES seconds,
+ * generous enough to outlast a slow conduit.
+ */
+#define RTL8365MB_D_SDS_RELATCH_INTERVAL	(HZ)
+#define RTL8365MB_D_SDS_RELATCH_MAX_TRIES	15
+
+/* The SerDes stays parked until the restore write succeeds, so a failed
+ * write is retried this many times before giving up until the next run.
+ */
+#define RTL8365MB_D_SDS_RESTORE_TRIES		3
+
+/* How often a latched (or out-of-budget) SerDes is checked, and re-latched
+ * if still down. Much slower than the re-latch interval.
+ */
+#define RTL8365MB_D_SDS_HEALTHCHECK_INTERVAL	(10 * HZ)
+
 /* SerDes internal registers, accessed via the SDS_INDACS registers. The BMCR
  * data path reset holds BMCR_ANENABLE | BMCR_ISOLATE while toggling the
  * vendor-specific low bits from phase 1 to phase 2, which triggers a data path
@@ -928,10 +951,16 @@ struct rtl8365mb_port {
  * @chip_info: chip-specific info about the attached switch
  * @cpu: CPU tagging and CPU port configuration for this chip
  * @mib_lock: prevent concurrent reads of MIB counters
+ * @sds_lock: serializes access to the shared SDS_INDACS ADR/CMD/DATA window,
+ *            reachable both from phylink's PCS callbacks and from the
+ *            family D SerDes re-latch work
  * @ports: per-port data
  * @pcs: PCS for the SerDes external interface
  * @sds_supported: SerDes tuning parameters match the chip option, so the
  *                 SerDes interface modes can be advertised
+ * @sds_relatch: re-latch edges and link health check (family D)
+ * @sds_relatch_count: next attempt of the re-latch episode, 0 once latched
+ * @sds_misc_target_val: SDS_MISC_CFG_MASK fields the re-latch work restores
  *
  * Private data for this driver.
  */
@@ -941,9 +970,13 @@ struct rtl8365mb {
 	const struct rtl8365mb_chip_info *chip_info;
 	struct rtl8365mb_cpu cpu;
 	struct mutex mib_lock;
+	struct mutex sds_lock;
 	struct rtl8365mb_port ports[RTL8365MB_MAX_NUM_PORTS];
 	struct phylink_pcs pcs;
 	bool sds_supported;
+	struct delayed_work sds_relatch;
+	unsigned int sds_relatch_count;
+	u32 sds_misc_target_val;
 };
 
 #define pcs_to_rtl8365mb(_pcs) container_of((_pcs), struct rtl8365mb, pcs)
@@ -1350,43 +1383,53 @@ static int rtl8365mb_ext_config_rgmii(struct realtek_priv *priv, int port,
 static int rtl8365mb_sds_write(struct realtek_priv *priv, u8 index,
 			       u16 addr, u16 data)
 {
+	struct rtl8365mb *mb = priv->chip_data;
 	int ret;
 
+	mutex_lock(&mb->sds_lock);
+
 	ret = regmap_write(priv->map, RTL8365MB_SDS_INDACS_DATA_REG, data);
 	if (ret)
-		return ret;
+		goto out_unlock;
 
 	ret = regmap_write(priv->map, RTL8365MB_SDS_INDACS_ADR_REG, addr);
 	if (ret)
-		return ret;
+		goto out_unlock;
 
 	/* The SerDes indirect access engine completes the command within the
 	 * register write transaction, so there is no need to wait or poll for
 	 * completion before the next access, matching the vendor driver.
 	 */
-	return regmap_write(priv->map, RTL8365MB_SDS_INDACS_CMD_REG,
-			    RTL8365MB_SDS_INDACS_CMD_RUN_MASK |
-			    RTL8365MB_SDS_INDACS_CMD_WR_MASK |
-			    FIELD_PREP(RTL8365MB_SDS_INDACS_CMD_INDEX_MASK,
-				       index));
+	ret = regmap_write(priv->map, RTL8365MB_SDS_INDACS_CMD_REG,
+			   RTL8365MB_SDS_INDACS_CMD_RUN_MASK |
+			   RTL8365MB_SDS_INDACS_CMD_WR_MASK |
+			   FIELD_PREP(RTL8365MB_SDS_INDACS_CMD_INDEX_MASK,
+				      index));
+
+out_unlock:
+	mutex_unlock(&mb->sds_lock);
+	return ret;
 }
 
 static int rtl8365mb_sds_read(struct realtek_priv *priv, u8 index,
 			      u16 addr, u16 *data)
 {
+	struct rtl8365mb *mb = priv->chip_data;
 	u32 val;
 	int ret;
 
+	mutex_lock(&mb->sds_lock);
+
 	ret = regmap_write(priv->map, RTL8365MB_SDS_INDACS_ADR_REG, addr);
 	if (ret)
-		return ret;
+		goto out_unlock;
 
 	ret = regmap_write(priv->map, RTL8365MB_SDS_INDACS_CMD_REG,
 			   RTL8365MB_SDS_INDACS_CMD_RUN_MASK |
 			   FIELD_PREP(RTL8365MB_SDS_INDACS_CMD_INDEX_MASK,
 				      index));
 	if (ret)
-		return ret;
+		goto out_unlock;
 
 	/* Wait for the indirect read to complete: the engine clears the BUSY
 	 * bit once the data register holds the result.
@@ -1396,15 +1439,19 @@ static int rtl8365mb_sds_read(struct realtek_priv *priv, u8 index,
 				       !(val & RTL8365MB_SDS_INDACS_CMD_BUSY_MASK),
 				       10, 1000);
 	if (ret)
-		return ret;
+		goto out_unlock;
 
 	ret = regmap_read(priv->map, RTL8365MB_SDS_INDACS_DATA_REG, &val);
 	if (ret)
-		return ret;
+		goto out_unlock;
 
 	*data = val;
 
-	return 0;
+	ret = 0;
+
+out_unlock:
+	mutex_unlock(&mb->sds_lock);
+	return ret;
 }
 
 /* The vendor driver selects between two sets of SerDes tuning parameters based
@@ -1526,6 +1573,13 @@ static int rtl8365mb_pcs_config(struct phylink_pcs *pcs, unsigned int neg_mode,
 
 	is_d = rtl8365mb_get_family(priv) == RTL8365MB_FAMILY_D;
 
+	/* Cancel any in-flight re-latch edge before touching SDS_MISC: the
+	 * work parks SDS_MISC and restores the target value after a sleep, so
+	 * it could otherwise write a stale target over the new configuration.
+	 */
+	if (is_d)
+		cancel_delayed_work_sync(&mb->sds_relatch);
+
 	/* Select the appropriate tuning table and SDS mode */
 	if (interface == PHY_INTERFACE_MODE_2500BASEX) {
 		if (is_d) {
@@ -1611,7 +1665,9 @@ static int rtl8365mb_pcs_config(struct phylink_pcs *pcs, unsigned int neg_mode,
 	if (ret)
 		return ret;
 
-	if (!is_d) {
+	if (is_d) {
+		WRITE_ONCE(mb->sds_misc_target_val, misc_val);
+	} else {
 		val = sds_mode << RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_OFFSET(id);
 		ret = regmap_update_bits(priv->map,
 					 RTL8365MB_DIGITAL_INTERFACE_SELECT_REG(id),
@@ -1658,8 +1714,155 @@ static int rtl8365mb_pcs_config(struct phylink_pcs *pcs, unsigned int neg_mode,
 	val &= ~RTL8365MB_SDS_NWAY_EN_MASK;
 	val |= RTL8365MB_SDS_NWAY_RESTART_MASK;
 
-	return rtl8365mb_sds_write(priv, sds_index,
-				   RTL8365MB_SDS_REG_NWAY, val);
+	ret = rtl8365mb_sds_write(priv, sds_index,
+				  RTL8365MB_SDS_REG_NWAY, val);
+	if (ret)
+		return ret;
+
+	/* The re-latch edge has only been observed with HSGMII, so the work is
+	 * only started for 2500base-x. Start a new episode and kick off the
+	 * first attempt; see rtl8365mb_sds_relatch_work() for why this cannot
+	 * wait for phylink to ask again.
+	 */
+	if (is_d && interface == PHY_INTERFACE_MODE_2500BASEX) {
+		WRITE_ONCE(mb->sds_relatch_count, 1);
+		schedule_delayed_work(&mb->sds_relatch, 0);
+	}
+
+	return 0;
+}
+
+/* The family D receiver latches on a DISABLE -> mode edge in SDS_MISC
+ * rather than on the value, and only once the far-end MAC has brought up
+ * its half of the link. No local signal predicts that (bit 8 of the SDS
+ * link-status word does not change ahead of it), so the work cannot wait
+ * for it, only check afterwards whether an edge took. Nor does phylink
+ * call rtl8365mb_pcs_get_state() for a link without in-band signalling
+ * such as the fixed-link CPU trunk (mb->pcs.poll only arms phylink's own
+ * poll for in-band links), so this cannot rely on being polled at all.
+ * Instead, pcs_config() starts an episode and this work re-arms itself
+ * after every edge, its next run checking whether the edge took.
+ *
+ * An episode is capped at RTL8365MB_D_SDS_RELATCH_MAX_TRIES edges, spaced
+ * RTL8365MB_D_SDS_RELATCH_INTERVAL apart, so that a far end which never
+ * comes up costs a bounded burst of 20 ms parks. The run after the last
+ * edge only checks whether it took and reports failure; from then on one
+ * edge is driven per RTL8365MB_D_SDS_HEALTHCHECK_INTERVAL, so a far end
+ * that comes up late is recovered without a reconfiguration. Once the
+ * receiver has latched the work just polls the link at the same slow
+ * interval; finding it down then starts a new episode, e.g. after the far
+ * end reset its PLL without a reconfiguration.
+ *
+ * sds_relatch_count is the number of the next attempt of the episode: 0
+ * while latched, 1..MAX_TRIES in budget, MAX_TRIES + 1 for the run that
+ * only reports, and above that once out of budget.
+ */
+static void rtl8365mb_sds_relatch_work(struct work_struct *work)
+{
+	struct rtl8365mb *mb = container_of(to_delayed_work(work),
+					    struct rtl8365mb, sds_relatch);
+	struct realtek_priv *priv = mb->priv;
+	u32 park = (READ_ONCE(mb->sds_misc_target_val) &
+		    ~RTL8365MB_D_SDS_MISC_MODE_FIELD_MASK) |
+		   RTL8365MB_D_PORT_SDS_MODE_DISABLE;
+	unsigned long delay = RTL8365MB_D_SDS_RELATCH_INTERVAL;
+	unsigned int attempts;
+	u16 status;
+	int ret;
+	int i;
+
+	/* The condition that queued this work may already be stale by the
+	 * time it runs (e.g. an earlier edge from a prior attempt just
+	 * latched). Parking an already-live link would drop it for no
+	 * reason.
+	 */
+	ret = rtl8365mb_sds_read(priv, RTL8365MB_D_SDS_EXT0_INDEX,
+				 RTL8365MB_SDS_REG_LINK_STATUS, &status);
+	if (ret) {
+		dev_err_ratelimited(priv->dev,
+				    "failed to read SerDes link status: %pe\n",
+				    ERR_PTR(ret));
+		goto rearm;
+	}
+	if (status & RTL8365MB_SDS_LINK_STATUS_LINK_MASK) {
+		/* Latched: end the episode, keep watching for a later loss. */
+		WRITE_ONCE(mb->sds_relatch_count, 0);
+		delay = RTL8365MB_D_SDS_HEALTHCHECK_INTERVAL;
+		goto rearm;
+	}
+
+	attempts = READ_ONCE(mb->sds_relatch_count);
+	if (!attempts) {
+		dev_warn(priv->dev,
+			 "SerDes link lost outside a reconfiguration; re-latching\n");
+		attempts = 1;
+	} else if (attempts == RTL8365MB_D_SDS_RELATCH_MAX_TRIES + 1) {
+		/* This run only checked whether the last in-budget edge
+		 * took. The first out-of-budget edge comes one healthcheck
+		 * interval from now, not on this pass.
+		 */
+		WRITE_ONCE(mb->sds_relatch_count, attempts + 1);
+		dev_warn(priv->dev,
+			 "SerDes did not latch after %u re-latch attempts; still retrying every %d s\n",
+			 RTL8365MB_D_SDS_RELATCH_MAX_TRIES,
+			 RTL8365MB_D_SDS_HEALTHCHECK_INTERVAL / HZ);
+		delay = RTL8365MB_D_SDS_HEALTHCHECK_INTERVAL;
+		goto rearm;
+	}
+
+	if (attempts <= RTL8365MB_D_SDS_RELATCH_MAX_TRIES)
+		WRITE_ONCE(mb->sds_relatch_count, attempts + 1);
+	else
+		/* Past the fast-retry budget. The receiver latches only on a
+		 * DISABLE -> mode edge and nothing re-runs pcs_config() for a
+		 * link without in-band signalling, so keep driving one edge
+		 * per interval.
+		 */
+		delay = RTL8365MB_D_SDS_HEALTHCHECK_INTERVAL;
+
+	ret = regmap_update_bits(priv->map, RTL8365MB_SDS_MISC_REG,
+				 RTL8365MB_D_SDS_MISC_CFG_MASK, park);
+	if (ret) {
+		dev_err_ratelimited(priv->dev,
+				    "failed to park SDS_MISC: %pe\n",
+				    ERR_PTR(ret));
+		goto rearm;
+	}
+
+	usleep_range(20000, 21000);
+
+	for (i = 0; i < RTL8365MB_D_SDS_RESTORE_TRIES; i++) {
+		ret = regmap_update_bits(priv->map, RTL8365MB_SDS_MISC_REG,
+					 RTL8365MB_D_SDS_MISC_CFG_MASK,
+					 READ_ONCE(mb->sds_misc_target_val));
+		if (!ret)
+			break;
+		usleep_range(1000, 2000);
+	}
+	if (ret) {
+		dev_err_ratelimited(priv->dev,
+				    "failed to restore SDS_MISC: %pe\n",
+				    ERR_PTR(ret));
+		/* The SerDes is left parked: come back soon rather than
+		 * at the (possibly 10 s) pace chosen above.
+		 */
+		delay = RTL8365MB_D_SDS_RELATCH_INTERVAL;
+		goto rearm;
+	}
+
+	dev_dbg(priv->dev, "SerDes re-latch edge driven (attempt %u)\n",
+		attempts);
+
+	/* This edge may not have taken either; the next run checks. */
+rearm:
+	schedule_delayed_work(&mb->sds_relatch, delay);
+}
+
+static void rtl8365mb_sds_relatch_cancel(void *data)
+{
+	struct rtl8365mb *mb = data;
+
+	cancel_delayed_work_sync(&mb->sds_relatch);
 }
 
 static bool rtl8365mb_interface_is_serdes(phy_interface_t interface)
@@ -1802,11 +2005,20 @@ static void rtl8365mb_pcs_link_up(struct phylink_pcs *pcs,
 	}
 }
 
+static void rtl8365mb_pcs_disable(struct phylink_pcs *pcs)
+{
+	struct rtl8365mb *mb = pcs_to_rtl8365mb(pcs);
+
+	if (rtl8365mb_get_family(mb->priv) == RTL8365MB_FAMILY_D)
+		cancel_delayed_work_sync(&mb->sds_relatch);
+}
+
 static const struct phylink_pcs_ops rtl8365mb_pcs_ops = {
 	.pcs_inband_caps = rtl8365mb_pcs_inband_caps,
 	.pcs_config = rtl8365mb_pcs_config,
 	.pcs_get_state = rtl8365mb_pcs_get_state,
 	.pcs_link_up = rtl8365mb_pcs_link_up,
+	.pcs_disable = rtl8365mb_pcs_disable,
 };
 
 static int rtl8365mb_ext_config_forcemode(struct realtek_priv *priv, int port,
@@ -3506,6 +3718,10 @@ out_error:
 static void rtl8365mb_teardown(struct dsa_switch *ds)
 {
 	struct realtek_priv *priv = ds->priv;
+	struct rtl8365mb *mb = priv->chip_data;
+
+	if (rtl8365mb_get_family(priv) == RTL8365MB_FAMILY_D)
+		cancel_delayed_work_sync(&mb->sds_relatch);
 
 	rtl8365mb_stats_teardown(priv);
 	rtl8365mb_irq_teardown(priv);
@@ -3572,6 +3788,24 @@ static int rtl8365mb_detect(struct realtek_priv *priv)
 	dev_info(priv->dev, "found an %s switch\n", mb->chip_info->name);
 
 	priv->num_ports = RTL8365MB_MAX_NUM_PORTS;
+
+	ret = devm_mutex_init(priv->dev, &mb->sds_lock);
+	if (ret)
+		return ret;
+
+	if (rtl8365mb_get_family(priv) == RTL8365MB_FAMILY_D) {
+		/* Registered after sds_lock, so on release the work is
+		 * cancelled before the mutex is destroyed.
+		 */
+		INIT_DELAYED_WORK(&mb->sds_relatch,
+				  rtl8365mb_sds_relatch_work);
+		ret = devm_add_action_or_reset(priv->dev,
+					       rtl8365mb_sds_relatch_cancel,
+					       mb);
+		if (ret)
+			return ret;
+	}
+
 	mb->priv = priv;
 	mb->cpu.trap_port = RTL8365MB_MAX_NUM_PORTS;
 	mb->cpu.insert = RTL8365MB_CPU_INSERT_TO_ALL;
-- 
2.53.0

[PATCH net-next v3 9/9] net: dsa: realtek: rtl8365mb: add support for RTL8367S-VB

[Mieczyslaw Nalewaj]

Add the RTL8367S-VB (chip ID 0x6642, version 0x0010) to the chip table.
It is the first chip of family D, whose handling was added in the
preceding patches, so this is the patch that makes it reachable.

The SGMII/HSGMII SerDes of this chip sits on external interface 0
(port 6), and the MII/TMII/RMII/RGMII interface on external interface 1
(port 7), the other way round than on family C chips. The chip reuses the
existing initialization jam table.

The chip has 8 ports, not 11. Cap priv->num_ports at
RTL8365MB_D_MAX_NUM_PORTS for family D. This is a functional change: it
sets ds->num_ports, the IRQ domain size and the bound of every loop over
priv->num_ports.

The L2 learning limit is the same as on family C (2112 entries), as
given by the Realtek rtl8367 common API (rtl8367_common V1.4.2), so
RTL8365MB_LEARN_LIMIT_MAX needs no per-family handling; only its
comment is updated.

Tested on a TP-Link Archer AX55 v1 (RTL8367S-VB, CPU port over HSGMII
to an IPQ5018) with bridge VLAN filtering and per-port PVIDs.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
---
 drivers/net/dsa/realtek/rtl8365mb_main.c | 31 +++++++++++++++++++++---
 1 file changed, 27 insertions(+), 4 deletions(-)

diff --git a/drivers/net/dsa/realtek/rtl8365mb_main.c b/drivers/net/dsa/realtek/rtl8365mb_main.c
index 5d80409..c604560 100644
--- a/drivers/net/dsa/realtek/rtl8365mb_main.c
+++ b/drivers/net/dsa/realtek/rtl8365mb_main.c
@@ -89,6 +89,12 @@
  * things will work out-of-the-box for other chips, and a careful review of the
  * vendor driver may be needed to expand support. The RTL8365MB-VC seems to be
  * one of the simpler chips.
+ *
+ * The RTL8367S-VB (chip ID 0x6642) is not part of the family listed above. It
+ * belongs to a newer generation, which this driver calls family D. Its
+ * registers differ in the VLAN table, the external interface speed and RGMII
+ * configuration and the SerDes, so the code paths specific to it are selected
+ * with rtl8365mb_get_family().
  */
 
 #include <linux/bitfield.h>
@@ -118,9 +124,10 @@
 #define RTL8365MB_NUM_PHYREGS		32
 #define RTL8365MB_PHYREGMAX		(RTL8365MB_NUM_PHYREGS - 1)
 #define RTL8365MB_MAX_NUM_PORTS		11
-/* Valid for the whole family except RTL8370B, which has 4160 entries.
- * RTL8370B is mentioned in vendor code but it might not even belong
- * to the same RTL8367C family.
+#define RTL8365MB_D_MAX_NUM_PORTS	8
+/* Valid for the whole RTL8367C family (and for family D, RTL8367S-VB)
+ * except RTL8370B, which has 4160 entries. RTL8370B is mentioned in
+ * vendor code but it might not even belong to the same RTL8367C family.
  */
 #define RTL8365MB_LEARN_LIMIT_MAX	2112
 #define RTL8365MB_MAX_NUM_EXTINTS	3
@@ -874,6 +881,19 @@ static const struct rtl8365mb_chip_info rtl8365mb_chip_infos[] = {
 		.jam_table = rtl8365mb_init_jam_8365mb_vc,
 		.jam_size = ARRAY_SIZE(rtl8365mb_init_jam_8365mb_vc),
 	},
+	{
+		.name = "RTL8367S-VB",
+		.chip_id = 0x6642,
+		.chip_ver = 0x0010,
+		.family = RTL8365MB_FAMILY_D,
+		.extints = {
+			{ 6, 0, PHY_INTF(SGMII) | PHY_INTF(HSGMII) },
+			{ 7, 1, PHY_INTF(MII) | PHY_INTF(TMII) |
+				PHY_INTF(RMII) | PHY_INTF(RGMII) },
+		},
+		.jam_table = rtl8365mb_init_jam_8365mb_vc,
+		.jam_size = ARRAY_SIZE(rtl8365mb_init_jam_8365mb_vc),
+	},
 };
 
 enum rtl8365mb_stp_state {
@@ -3787,7 +3807,10 @@ static int rtl8365mb_detect(struct realtek_priv *priv)
 
 	dev_info(priv->dev, "found an %s switch\n", mb->chip_info->name);
 
-	priv->num_ports = RTL8365MB_MAX_NUM_PORTS;
+	if (rtl8365mb_get_family(priv) == RTL8365MB_FAMILY_D)
+		priv->num_ports = RTL8365MB_D_MAX_NUM_PORTS;
+	else
+		priv->num_ports = RTL8365MB_MAX_NUM_PORTS;
 
 	ret = devm_mutex_init(priv->dev, &mb->sds_lock);
 	if (ret)
-- 
2.53.0