Re: [PATCH 3/5] ARM: dts: add dts files for bcmbca soc 47622

[Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>]

On 11/04/2022 19:28, William Zhang wrote:
> Add dts for ARMv7 based broadband SoC BCM47622. bcm47622.dtsi is the
> SoC description dts header and bcm947622.dts is a simple dts file for
> Broadcom BCM947622 Reference board that only enable the UART port.
> 


Thank you for your patch. There is something to discuss/improve.

> + */
> +
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +
> +/ {
> +	compatible = "brcm,bcm47622";

This does not match your bindings. Even if it is not used.

> +	#address-cells = <1>;
> +	#size-cells = <1>;
> +
> +	interrupt-parent = <&gic>;
> +
> +	cpus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		CA7_0: cpu@0 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a7";
> +			reg = <0x0>;
> +			next-level-cache = <&L2_0>;
> +			enable-method = "psci";
> +		};
> +
> +		CA7_1: cpu@1 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a7";
> +			reg = <0x1>;
> +			next-level-cache = <&L2_0>;
> +			enable-method = "psci";
> +		};
> +		CA7_2: cpu@2 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a7";
> +			reg = <0x2>;
> +			next-level-cache = <&L2_0>;
> +			enable-method = "psci";
> +		};
> +		CA7_3: cpu@3 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a7";
> +			reg = <0x3>;
> +			next-level-cache = <&L2_0>;
> +			enable-method = "psci";
> +		};
> +		L2_0: l2-cache0 {
> +			compatible = "cache";
> +		};
> +	};
> +
> +	timer {
> +		compatible = "arm,armv7-timer";
> +		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> +			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> +			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> +			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
> +		arm,cpu-registers-not-fw-configured;
> +	};
> +
> +	pmu: pmu {
> +		compatible = "arm,cortex-a7-pmu";
> +		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
> +			<GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
> +			<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
> +			<GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
> +		interrupt-affinity = <&CA7_0>, <&CA7_1>,
> +			<&CA7_2>, <&CA7_3>;
> +	};
> +
> +	clocks: clocks {
> +		periph_clk: periph_clk {

No underscores in node names.

> +			compatible = "fixed-clock";
> +			#clock-cells = <0>;
> +			clock-frequency = <200000000>;
> +		};
> +		uart_clk: uart_clk {
> +			compatible = "fixed-factor-clock";
> +			#clock-cells = <0>;
> +			clocks = <&periph_clk>;
> +			clock-div = <4>;
> +			clock-mult = <1>;
> +		};
> +	};
> +
> +	psci {
> +		compatible = "arm,psci-0.2";
> +		method = "smc";
> +		cpu_off = <1>;
> +		cpu_on = <2>;
> +	};
> +
> +	axi@81000000 {
> +		compatible = "simple-bus";
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges = <0 0x81000000 0x818000>;
> +
> +		gic: interrupt-controller@1000 {
> +			compatible = "arm,cortex-a7-gic";
> +			#interrupt-cells = <3>;
> +			#address-cells = <0>;
> +			interrupt-controller;
> +			reg = <0x1000 0x1000>,
> +				<0x2000 0x2000>;
> +		};
> +	};
> +
> +	periph-bus@ff800000 {

just "bus" to be generic?



Best regards,
Krzysztof