From: "Måns Rullgård" <mans@mansr.com>
To: Felix Fietkau <nbd@nbd.name>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>,
David Miller <davem@davemloft.net>,
Netdev <netdev@vger.kernel.org>,
WireGuard mailing list <wireguard@lists.zx2c4.com>,
LKML <linux-kernel@vger.kernel.org>,
linux-mips@linux-mips.org
Subject: Re: Misalignment, MIPS, and ip_hdr(skb)->version
Date: Sat, 10 Dec 2016 20:32:44 +0000 [thread overview]
Message-ID: <yw1xy3znwmmr.fsf@unicorn.mansr.com> (raw)
In-Reply-To: <7f8ba817-73ef-e1e1-4fdf-b9178e922008@nbd.name> (Felix Fietkau's message of "Sat, 10 Dec 2016 21:09:57 +0100")
Felix Fietkau <nbd@nbd.name> writes:
> On 2016-12-10 14:25, Måns Rullgård wrote:
>> Felix Fietkau <nbd@nbd.name> writes:
>>
>>> On 2016-12-07 19:54, Jason A. Donenfeld wrote:
>>>> On Wed, Dec 7, 2016 at 7:51 PM, David Miller <davem@davemloft.net> wrote:
>>>>> It's so much better to analyze properly where the misalignment comes from
>>>>> and address it at the source, as we have for various cases that trip up
>>>>> Sparc too.
>>>>
>>>> That's sort of my attitude too, hence starting this thread. Any
>>>> pointers you have about this would be most welcome, so as not to
>>>> perpetuate what already seems like an issue in other parts of the
>>>> stack.
>>> Hi Jason,
>>>
>>> I'm the author of that hackish LEDE/OpenWrt patch that works around the
>>> misalignment issues. Here's some context regarding that patch:
>>>
>>> I intentionally put it in the target specific patches for only one of
>>> our MIPS targets. There are a few ar71xx devices where the misalignment
>>> cannot be fixed, because the Ethernet MAC has a 4-byte DMA alignment
>>> requirement, and does not support inserting 2 bytes of padding to
>>> correct the IP header misalignment.
>>>
>>> With these limitations the choice was between this ugly network stack
>>> patch or inserting a very expensive memmove in the data path (which is
>>> better than taking the mis-alignment traps, but still hurts routing
>>> performance significantly).
>>
>> I solved this problem in an Ethernet driver by copying the initial part
>> of the packet to an aligned skb and appending the remainder using
>> skb_add_rx_frag(). The kernel network stack only cares about the
>> headers, so the alignment of the packet payload doesn't matter.
>
> I considered that as well, but it's bad for routing performance if the
> ethernet MAC does not support scatter/gather for xmit.
> Unfortunately that limitation is quite common on embedded hardware.
Yes, I can see that being an issue. However, if you're doing zero-copy
routing, the header part of the original buffer should still be there,
unused, so you could presumably copy the header of the outgoing packet
there and then do dma as usual. Maybe there's something in the network
stack that makes this impossible though.
--
Måns Rullgård
next prev parent reply other threads:[~2016-12-10 20:32 UTC|newest]
Thread overview: 27+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-12-07 18:35 Jason A. Donenfeld
2016-12-07 18:47 ` Dave Taht
2016-12-07 18:51 ` David Miller
2016-12-07 18:54 ` Jason A. Donenfeld
2016-12-07 19:52 ` David Miller
2016-12-08 0:29 ` Jason A. Donenfeld
2016-12-08 0:37 ` David Miller
2016-12-08 22:20 ` Jason A. Donenfeld
2016-12-08 23:14 ` David Miller
2016-12-11 8:07 ` Willy Tarreau
2016-12-11 10:47 ` Måns Rullgård
2016-12-10 12:25 ` Felix Fietkau
2016-12-10 13:25 ` Måns Rullgård
2016-12-10 20:09 ` Felix Fietkau
2016-12-10 20:32 ` Måns Rullgård [this message]
2016-12-10 20:36 ` Felix Fietkau
2016-12-12 16:19 ` David Laight
2016-12-12 16:31 ` Måns Rullgård
2016-12-08 0:30 ` Hannes Frederic Sowa
2016-12-08 4:34 ` Daniel Kahn Gillmor
2016-12-09 11:26 ` Jiri Benc
2016-12-10 22:18 ` Dan Lüdtke
2016-12-11 7:15 ` Greg KH
2016-12-11 14:50 ` Jason A. Donenfeld
2016-12-11 15:30 ` Andrew Lunn
2016-12-11 15:37 ` Jason A. Donenfeld
2016-12-11 16:44 ` Willy Tarreau
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=yw1xy3znwmmr.fsf@unicorn.mansr.com \
--to=mans@mansr.com \
--cc=Jason@zx2c4.com \
--cc=davem@davemloft.net \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mips@linux-mips.org \
--cc=nbd@nbd.name \
--cc=netdev@vger.kernel.org \
--cc=wireguard@lists.zx2c4.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®