From: Lee Jones <lee.jones@linaro.org>
To: linux-kernel@vger.kernel.org, broonie@opensource.wolfsonmicro.com
Cc: Bengt Jonsson <bengt.g.jonsson@stericsson.com>,
Lee Jones <lee.jones@linaro.org>
Subject: [PATCH 09/73] ARM: ux500: regulators: Add mask for configuration
Date: Mon, 4 Feb 2013 11:53:24 +0000 [thread overview]
Message-ID: <1359978868-28736-10-git-send-email-lee.jones@linaro.org> (raw)
In-Reply-To: <1359978868-28736-1-git-send-email-lee.jones@linaro.org>
From: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
There is already before a register mask in the regulator driver
to allow some bits of a register to be initialized. The register
value is defined in the board configuration. This patch puts a
mask in the board configuration to specify which bits should
actually be altered. The purpose with this patch is to avoid
future mistakes when updating the allowed bits in the regulator
driver.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Tested-by: Jonas ABERG <jonas.aberg@stericsson.com>
---
arch/arm/mach-ux500/board-mop500-regulators.c | 72 ++++++++++++-------------
drivers/regulator/ab8500.c | 36 +++++--------
include/linux/regulator/ab8500.h | 10 ++--
3 files changed, 56 insertions(+), 62 deletions(-)
diff --git a/arch/arm/mach-ux500/board-mop500-regulators.c b/arch/arm/mach-ux500/board-mop500-regulators.c
index 556eba5..ac512bc 100644
--- a/arch/arm/mach-ux500/board-mop500-regulators.c
+++ b/arch/arm/mach-ux500/board-mop500-regulators.c
@@ -129,19 +129,19 @@ ab8500_regulator_reg_init[AB8500_NUM_REGULATOR_REGISTERS] = {
* VpllRequestCtrl = HP/LP depending on VxRequest
* VextSupply1RequestCtrl = HP/LP depending on VxRequest
*/
- INIT_REGULATOR_REGISTER(AB8500_REGUREQUESTCTRL2, 0x00),
+ INIT_REGULATOR_REGISTER(AB8500_REGUREQUESTCTRL2, 0xfc, 0x00),
/*
* VextSupply2RequestCtrl = HP/LP depending on VxRequest
* VextSupply3RequestCtrl = HP/LP depending on VxRequest
* Vaux1RequestCtrl = HP/LP depending on VxRequest
* Vaux2RequestCtrl = HP/LP depending on VxRequest
*/
- INIT_REGULATOR_REGISTER(AB8500_REGUREQUESTCTRL3, 0x00),
+ INIT_REGULATOR_REGISTER(AB8500_REGUREQUESTCTRL3, 0xff, 0x00),
/*
* Vaux3RequestCtrl = HP/LP depending on VxRequest
* SwHPReq = Control through SWValid disabled
*/
- INIT_REGULATOR_REGISTER(AB8500_REGUREQUESTCTRL4, 0x00),
+ INIT_REGULATOR_REGISTER(AB8500_REGUREQUESTCTRL4, 0x07, 0x00),
/*
* Vsmps1SysClkReq1HPValid = enabled
* Vsmps2SysClkReq1HPValid = enabled
@@ -152,44 +152,44 @@ ab8500_regulator_reg_init[AB8500_NUM_REGULATOR_REGISTERS] = {
* Vaux2SysClkReq1HPValid = disabled
* Vaux3SysClkReq1HPValid = disabled
*/
- INIT_REGULATOR_REGISTER(AB8500_REGUSYSCLKREQ1HPVALID1, 0x17),
+ INIT_REGULATOR_REGISTER(AB8500_REGUSYSCLKREQ1HPVALID1, 0xff, 0x17),
/*
* VextSupply1SysClkReq1HPValid = disabled
* VextSupply2SysClkReq1HPValid = disabled
* VextSupply3SysClkReq1HPValid = SysClkReq1 controlled
*/
- INIT_REGULATOR_REGISTER(AB8500_REGUSYSCLKREQ1HPVALID2, 0x40),
+ INIT_REGULATOR_REGISTER(AB8500_REGUSYSCLKREQ1HPVALID2, 0x70, 0x40),
/*
* VanaHwHPReq1Valid = disabled
* Vaux1HwHPreq1Valid = disabled
* Vaux2HwHPReq1Valid = disabled
* Vaux3HwHPReqValid = disabled
*/
- INIT_REGULATOR_REGISTER(AB8500_REGUHWHPREQ1VALID1, 0x00),
+ INIT_REGULATOR_REGISTER(AB8500_REGUHWHPREQ1VALID1, 0xe8, 0x00),
/*
* VextSupply1HwHPReq1Valid = disabled
* VextSupply2HwHPReq1Valid = disabled
* VextSupply3HwHPReq1Valid = disabled
*/
- INIT_REGULATOR_REGISTER(AB8500_REGUHWHPREQ1VALID2, 0x00),
+ INIT_REGULATOR_REGISTER(AB8500_REGUHWHPREQ1VALID2, 0x07, 0x00),
/*
* VanaHwHPReq2Valid = disabled
* Vaux1HwHPReq2Valid = disabled
* Vaux2HwHPReq2Valid = disabled
* Vaux3HwHPReq2Valid = disabled
*/
- INIT_REGULATOR_REGISTER(AB8500_REGUHWHPREQ2VALID1, 0x00),
+ INIT_REGULATOR_REGISTER(AB8500_REGUHWHPREQ2VALID1, 0xe8, 0x00),
/*
* VextSupply1HwHPReq2Valid = disabled
* VextSupply2HwHPReq2Valid = disabled
* VextSupply3HwHPReq2Valid = HWReq2 controlled
*/
- INIT_REGULATOR_REGISTER(AB8500_REGUHWHPREQ2VALID2, 0x04),
+ INIT_REGULATOR_REGISTER(AB8500_REGUHWHPREQ2VALID2, 0x07, 0x04),
/*
* VanaSwHPReqValid = disabled
* Vaux1SwHPReqValid = disabled
*/
- INIT_REGULATOR_REGISTER(AB8500_REGUSWHPREQVALID1, 0x00),
+ INIT_REGULATOR_REGISTER(AB8500_REGUSWHPREQVALID1, 0xa0, 0x00),
/*
* Vaux2SwHPReqValid = disabled
* Vaux3SwHPReqValid = disabled
@@ -197,7 +197,7 @@ ab8500_regulator_reg_init[AB8500_NUM_REGULATOR_REGISTERS] = {
* VextSupply2SwHPReqValid = disabled
* VextSupply3SwHPReqValid = disabled
*/
- INIT_REGULATOR_REGISTER(AB8500_REGUSWHPREQVALID2, 0x00),
+ INIT_REGULATOR_REGISTER(AB8500_REGUSWHPREQVALID2, 0x1f, 0x00),
/*
* SysClkReq2Valid1 = SysClkReq2 controlled
* SysClkReq3Valid1 = disabled
@@ -207,7 +207,7 @@ ab8500_regulator_reg_init[AB8500_NUM_REGULATOR_REGISTERS] = {
* SysClkReq7Valid1 = disabled
* SysClkReq8Valid1 = disabled
*/
- INIT_REGULATOR_REGISTER(AB8500_REGUSYSCLKREQVALID1, 0x2a),
+ INIT_REGULATOR_REGISTER(AB8500_REGUSYSCLKREQVALID1, 0xfe, 0x2a),
/*
* SysClkReq2Valid2 = disabled
* SysClkReq3Valid2 = disabled
@@ -217,7 +217,7 @@ ab8500_regulator_reg_init[AB8500_NUM_REGULATOR_REGISTERS] = {
* SysClkReq7Valid2 = disabled
* SysClkReq8Valid2 = disabled
*/
- INIT_REGULATOR_REGISTER(AB8500_REGUSYSCLKREQVALID2, 0x20),
+ INIT_REGULATOR_REGISTER(AB8500_REGUSYSCLKREQVALID2, 0xfe, 0x20),
/*
* VTVoutEna = disabled
* Vintcore12Ena = disabled
@@ -225,73 +225,73 @@ ab8500_regulator_reg_init[AB8500_NUM_REGULATOR_REGISTERS] = {
* Vintcore12LP = inactive (HP)
* VTVoutLP = inactive (HP)
*/
- INIT_REGULATOR_REGISTER(AB8500_REGUMISC1, 0x10),
+ INIT_REGULATOR_REGISTER(AB8500_REGUMISC1, 0xfe, 0x10),
/*
* VaudioEna = disabled
* VdmicEna = disabled
* Vamic1Ena = disabled
* Vamic2Ena = disabled
*/
- INIT_REGULATOR_REGISTER(AB8500_VAUDIOSUPPLY, 0x00),
+ INIT_REGULATOR_REGISTER(AB8500_VAUDIOSUPPLY, 0x1e, 0x00),
/*
* Vamic1_dzout = high-Z when Vamic1 is disabled
* Vamic2_dzout = high-Z when Vamic2 is disabled
*/
- INIT_REGULATOR_REGISTER(AB8500_REGUCTRL1VAMIC, 0x00),
+ INIT_REGULATOR_REGISTER(AB8500_REGUCTRL1VAMIC, 0x03, 0x00),
/*
* VBBN = force OFF
* VBBP = force OFF
* NOTE! PRCMU register
*/
- INIT_REGULATOR_REGISTER(AB8500_ARMREGU2, 0x00),
+ INIT_REGULATOR_REGISTER(AB8500_ARMREGU2, 0x0f, 0x00),
/*
* VBBNSel1 = VBBP = VBBPFB
* VBBPSel1 = 0 V
* NOTE! PRCMU register
*/
- INIT_REGULATOR_REGISTER(AB8500_VBBSEL1, 0x00),
+ INIT_REGULATOR_REGISTER(AB8500_VBBSEL1, 0x0f, 0x00),
/*
* VBBNSel2 = VBBP = VBBPFB
* VBBPSel2 = 0 V
* NOTE! PRCMU register
*/
- INIT_REGULATOR_REGISTER(AB8500_VBBSEL2, 0x00),
+ INIT_REGULATOR_REGISTER(AB8500_VBBSEL2, 0x0f, 0x00),
/*
* Vsmps1Regu = HW control
* Vsmps1SelCtrl = Vsmps1 voltage defined by Vsmsp1Sel2
*/
- INIT_REGULATOR_REGISTER(AB8500_VSMPS1REGU, 0x06),
+ INIT_REGULATOR_REGISTER(AB8500_VSMPS1REGU, 0x0f, 0x06),
/*
* Vsmps2Regu = HW control
* Vsmps2SelCtrl = Vsmps2 voltage defined by Vsmsp2Sel2
*/
- INIT_REGULATOR_REGISTER(AB8500_VSMPS2REGU, 0x06),
+ INIT_REGULATOR_REGISTER(AB8500_VSMPS2REGU, 0x0f, 0x06),
/*
* Vsmps3Sel2 = 1.2125 V
* NOTE! PRCMU register
*/
- INIT_REGULATOR_REGISTER(AB8500_VSMPS3SEL2, 0x29),
+ INIT_REGULATOR_REGISTER(AB8500_VSMPS3SEL2, 0x7f, 0x29),
/*
* Vsmps3Regu = HW control
* Vsmps3SelCtrl = Vsmps3 voltage defined by Vsmps3Sel2
* NOTE! PRCMU register
*/
- INIT_REGULATOR_REGISTER(AB8500_VSMPS3REGU, 0x06),
+ INIT_REGULATOR_REGISTER(AB8500_VSMPS3REGU, 0x0f, 0x06),
/*
* Vsmps3Sel1 = 0.9 V
* NOTE! PRCMU register
*/
- INIT_REGULATOR_REGISTER(AB8500_VSMPS3SEL1, 0x10),
+ INIT_REGULATOR_REGISTER(AB8500_VSMPS3SEL1, 0x7f, 0x10),
/*
* VPll = Hw controlled
* VanaRegu = force off
*/
- INIT_REGULATOR_REGISTER(AB8500_VPLLVANAREGU, 0x02),
+ INIT_REGULATOR_REGISTER(AB8500_VPLLVANAREGU, 0x0f, 0x02),
/*
* VrefDDREna = disabled
* VrefDDRSleepMode = inactive (no pulldown)
*/
- INIT_REGULATOR_REGISTER(AB8500_VREFDDR, 0x00),
+ INIT_REGULATOR_REGISTER(AB8500_VREFDDR, 0x03, 0x00),
/*
* VextSupply1Regu = HW control
* VextSupply2Regu = HW control
@@ -299,37 +299,37 @@ ab8500_regulator_reg_init[AB8500_NUM_REGULATOR_REGISTERS] = {
* ExtSupply2Bypass = ExtSupply12LPn ball is 0 when Ena is 0
* ExtSupply3Bypass = ExtSupply3LPn ball is 0 when Ena is 0
*/
- INIT_REGULATOR_REGISTER(AB8500_EXTSUPPLYREGU, 0x2a),
+ INIT_REGULATOR_REGISTER(AB8500_EXTSUPPLYREGU, 0xff, 0x1a),
/*
* Vaux1Regu = force HP
* Vaux2Regu = force off
*/
- INIT_REGULATOR_REGISTER(AB8500_VAUX12REGU, 0x01),
+ INIT_REGULATOR_REGISTER(AB8500_VAUX12REGU, 0x0f, 0x01),
/*
* Vrf1Regu = HW control
* Vaux3Regu = force off
*/
- INIT_REGULATOR_REGISTER(AB8500_VRF1VAUX3REGU, 0x08),
+ INIT_REGULATOR_REGISTER(AB8500_VRF1VAUX3REGU, 0x0f, 0x08),
/*
* Vsmps1 = 1.15V
*/
- INIT_REGULATOR_REGISTER(AB8500_VSMPS1SEL1, 0x24),
+ INIT_REGULATOR_REGISTER(AB8500_VSMPS1SEL1, 0x3f, 0x24),
/*
* Vaux1Sel = 2.5 V
*/
- INIT_REGULATOR_REGISTER(AB8500_VAUX1SEL, 0x08),
+ INIT_REGULATOR_REGISTER(AB8500_VAUX1SEL, 0x0f, 0x08),
/*
* Vaux2Sel = 2.9 V
*/
- INIT_REGULATOR_REGISTER(AB8500_VAUX2SEL, 0x0d),
+ INIT_REGULATOR_REGISTER(AB8500_VAUX2SEL, 0x0f, 0x0d),
/*
* Vaux3Sel = 2.91 V
*/
- INIT_REGULATOR_REGISTER(AB8500_VRF1VAUX3SEL, 0x07),
+ INIT_REGULATOR_REGISTER(AB8500_VRF1VAUX3SEL, 0x07, 0x07),
/*
* VextSupply12LP = disabled (no LP)
*/
- INIT_REGULATOR_REGISTER(AB8500_REGUCTRL2SPARE, 0x00),
+ INIT_REGULATOR_REGISTER(AB8500_REGUCTRL2SPARE, 0x01, 0x00),
/*
* Vaux1Disch = short discharge time
* Vaux2Disch = short discharge time
@@ -338,13 +338,13 @@ ab8500_regulator_reg_init[AB8500_NUM_REGULATOR_REGISTERS] = {
* VTVoutDisch = short discharge time
* VaudioDisch = short discharge time
*/
- INIT_REGULATOR_REGISTER(AB8500_REGUCTRLDISCH, 0x00),
+ INIT_REGULATOR_REGISTER(AB8500_REGUCTRLDISCH, 0xfc, 0x00),
/*
* VanaDisch = short discharge time
* VdmicPullDownEna = pulldown disabled when Vdmic is disabled
* VdmicDisch = short discharge time
*/
- INIT_REGULATOR_REGISTER(AB8500_REGUCTRLDISCH2, 0x00),
+ INIT_REGULATOR_REGISTER(AB8500_REGUCTRLDISCH2, 0x16, 0x00),
};
/* AB8500 regulators */
diff --git a/drivers/regulator/ab8500.c b/drivers/regulator/ab8500.c
index d0ce436..7b7dd20 100644
--- a/drivers/regulator/ab8500.c
+++ b/drivers/regulator/ab8500.c
@@ -826,23 +826,20 @@ static struct ab8500_reg_init ab8500_reg_init[] = {
REG_INIT(AB8500_REGUCTRLDISCH2, 0x04, 0x44, 0x16),
};
-static int
-ab8500_regulator_init_registers(struct platform_device *pdev, int id, int value)
+static int ab8500_regulator_init_registers(struct platform_device *pdev,
+ int id, int mask, int value)
{
int err;
- if (value & ~ab8500_reg_init[id].mask) {
- dev_err(&pdev->dev,
- "Configuration error: value outside mask.\n");
- return -EINVAL;
- }
+ BUG_ON(value & ~mask);
+ BUG_ON(mask & ~ab8500_reg_init[id].mask);
+ /* initialize register */
err = abx500_mask_and_set_register_interruptible(
&pdev->dev,
ab8500_reg_init[id].bank,
ab8500_reg_init[id].addr,
- ab8500_reg_init[id].mask,
- value);
+ mask, value);
if (err < 0) {
dev_err(&pdev->dev,
"Failed to initialize 0x%02x, 0x%02x.\n",
@@ -850,13 +847,11 @@ ab8500_regulator_init_registers(struct platform_device *pdev, int id, int value)
ab8500_reg_init[id].addr);
return err;
}
-
dev_vdbg(&pdev->dev,
- "init: 0x%02x, 0x%02x, 0x%02x, 0x%02x\n",
- ab8500_reg_init[id].bank,
- ab8500_reg_init[id].addr,
- ab8500_reg_init[id].mask,
- value);
+ " init: 0x%02x, 0x%02x, 0x%02x, 0x%02x\n",
+ ab8500_reg_init[id].bank,
+ ab8500_reg_init[id].addr,
+ mask, value);
return 0;
}
@@ -975,19 +970,16 @@ static int ab8500_regulator_probe(struct platform_device *pdev)
/* initialize registers */
for (i = 0; i < pdata->num_regulator_reg_init; i++) {
- int id, value;
+ int id, mask, value;
id = pdata->regulator_reg_init[i].id;
+ mask = pdata->regulator_reg_init[i].mask;
value = pdata->regulator_reg_init[i].value;
/* check for configuration errors */
- if (id >= AB8500_NUM_REGULATOR_REGISTERS) {
- dev_err(&pdev->dev,
- "Configuration error: id outside range.\n");
- return -EINVAL;
- }
+ BUG_ON(id >= AB8500_NUM_REGULATOR_REGISTERS);
- err = ab8500_regulator_init_registers(pdev, id, value);
+ err = ab8500_regulator_init_registers(pdev, id, mask, value);
if (err < 0)
return err;
}
diff --git a/include/linux/regulator/ab8500.h b/include/linux/regulator/ab8500.h
index 2c6c962..a1d245f 100644
--- a/include/linux/regulator/ab8500.h
+++ b/include/linux/regulator/ab8500.h
@@ -48,13 +48,15 @@ enum ab9540_regulator_id {
/* AB8500 and AB9540 register initialization */
struct ab8500_regulator_reg_init {
int id;
+ u8 mask;
u8 value;
};
-#define INIT_REGULATOR_REGISTER(_id, _value) \
- { \
- .id = _id, \
- .value = _value, \
+#define INIT_REGULATOR_REGISTER(_id, _mask, _value) \
+ { \
+ .id = _id, \
+ .mask = _mask, \
+ .value = _value, \
}
/* AB8500 registers */
--
1.7.9.5
next prev parent reply other threads:[~2013-02-04 11:56 UTC|newest]
Thread overview: 85+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-02-04 11:53 [PATCH 00/73 v2] Regulators: Bring the AB8500 into the 20th century Lee Jones
2013-02-04 11:53 ` [PATCH 01/73] regulator: ab8500: Remove VBB from suspend force Lee Jones
2013-02-04 11:53 ` [PATCH 02/73] regulator: ab8500: Initialize Vrf1 regulator Lee Jones
2013-02-04 11:53 ` [PATCH 03/73] regulator: ab8500: Add init values for vsmps1/2 Lee Jones
2013-02-04 11:53 ` [PATCH 04/73] regulator: ab8500: Added SysClkReq1 control of Vpll Lee Jones
2013-02-04 11:53 ` [PATCH 05/73] ARM: ux500: Vsmps3 controlled by SysClkReq1 Lee Jones
2013-02-04 19:37 ` Mark Brown
2013-02-04 21:21 ` Linus Walleij
2013-02-05 12:01 ` Mark Brown
2013-02-05 13:03 ` Lee Jones
2013-02-26 9:44 ` Lee Jones
2013-02-26 10:16 ` Bengt Jönsson
2013-02-26 12:50 ` Mark Brown
2013-02-04 11:53 ` [PATCH 06/73] regulator: ab8500: Add set_mode/get_mode support Lee Jones
2013-02-04 11:53 ` [PATCH 07/73] regulator: ab8500: Fix for regulator_set_mode functionality Lee Jones
2013-02-04 19:38 ` Mark Brown
2013-02-04 11:53 ` [PATCH 08/73] regulator: ab8500: Added get_optimum_mode on regulators with idle mode Lee Jones
2013-02-04 11:53 ` Lee Jones [this message]
2013-02-04 11:53 ` [PATCH 10/73] regulator: ab8500: Added more configurable bits Lee Jones
2013-02-04 11:53 ` [PATCH 11/73] regulator: ab8500: Removed initialization of body biasing Lee Jones
2013-02-04 11:53 ` [PATCH 12/73] regulator: core: Show consumers that hold a regulator in Sysfs Lee Jones
2013-02-04 19:41 ` Mark Brown
2013-02-04 11:53 ` [PATCH 13/73] regulator: ab8500: Separate regulator and MFD platform data Lee Jones
2013-02-04 11:53 ` [PATCH 14/73] regulator: ab8500: Add support of low voltage battery Lee Jones
2013-02-04 11:53 ` [PATCH 15/73] ARM: ux500: Update displays in vaux1 consumer list Lee Jones
2013-02-04 11:53 ` [PATCH 16/73] regulator: ab8500-ext: Cosmetic changes Lee Jones
2013-02-04 11:53 ` [PATCH 17/73] regulator: ab8500-ext: Add HW request support Lee Jones
2013-02-04 11:53 ` [PATCH 18/73] regulator: ab8500-ext: Add suspend support Lee Jones
2013-02-04 11:53 ` [PATCH 19/73] regulator: ab8500-ext: Add regulator_set_mode/get_mode Lee Jones
2013-02-04 11:53 ` [PATCH 20/73] regulator: ab8500-ext: Add VextSupply1 regulator Lee Jones
2013-02-04 11:53 ` [PATCH 21/73] regulator: ab8500-ext: Add VextSupply2 regulator Lee Jones
2013-02-04 11:53 ` [PATCH 22/73] regulator: ab8500: Remove USB regulator Lee Jones
2013-02-04 11:53 ` [PATCH 23/73] regulator: ab8500: Init debug from regulator driver Lee Jones
2013-02-04 11:53 ` [PATCH 24/73] ARM: ux500: Add supply for the L3G4200D Gyroscope Lee Jones
2013-02-04 11:53 ` [PATCH 25/73] ARM: ux500: Add supply for the Proximity and Hal sensor Lee Jones
2013-02-04 11:53 ` [PATCH 26/73] ARM: ux500: Add supply for the Ambient light sensor device Lee Jones
2013-02-04 11:53 ` [PATCH 27/73] ARM: ux500: Add supply for the Pressure sensor Lee Jones
2013-02-04 11:53 ` [PATCH 28/73] ARM: ux500: Add supply for the Cypress TrueTouch Touchscreen Lee Jones
2013-02-04 11:53 ` [PATCH 29/73] ARM: ux500: Add supply for the MMIO Camera Lee Jones
2013-02-04 11:53 ` [PATCH 30/73] regulator: ab8500: Remove Vsafe voltage settings Lee Jones
2013-02-04 11:53 ` [PATCH 31/73] regulator: ab8500: Remove Vsafe settings Lee Jones
2013-02-04 11:53 ` [PATCH 32/73] regulator: ab8500: Clean out SoC registers Lee Jones
2013-02-04 11:53 ` [PATCH 33/73] regulator: ab8500: Add support for the AB9540 Lee Jones
2013-02-04 11:53 ` [PATCH 34/73] regulator: ab8500: Correct TVOUT regulator start-up delay Lee Jones
2013-02-04 11:53 ` [PATCH 35/73] regulator: ab8500-ext: Add support for AB8505/AB9540 Lee Jones
2013-02-04 11:53 ` [PATCH 36/73] ARM: ux500: Partially revert changes surrounding audio regulators Lee Jones
2013-02-04 11:53 ` [PATCH 37/73] regulator: ab8500: add support for ab8505 Lee Jones
2013-02-04 11:53 ` [PATCH 38/73] ARM: ux500: regulator: Use device IDs instead of device names Lee Jones
2013-02-04 11:53 ` [PATCH 39/73] regulator: ab8500-ext: Add support for AB9540 regulators Lee Jones
2013-02-04 11:53 ` [PATCH 40/73] regulator: ab8500: Add AB8505 register initialization Lee Jones
2013-02-04 11:53 ` [PATCH 41/73] regulator: ab8500: Provide full settings for AB8540 regulators Lee Jones
2013-02-04 11:53 ` [PATCH 42/73] regulator: ab8500: Correct init mask for AB8540 Lee Jones
2013-02-04 11:53 ` [PATCH 43/73] regulator: ab8500: Add VSDIO definition for the AB8540 Lee Jones
2013-02-04 11:53 ` [PATCH 44/73] regulator: ab8500: Vaux5/6 cannot be disabled on " Lee Jones
2013-02-04 11:54 ` [PATCH 45/73] regulator: ab8500: Update voltage handling for fixed voltage regulators Lee Jones
2013-02-04 11:54 ` [PATCH 46/73] regulator: ab8500: Delete useless fixed_uV field Lee Jones
2013-02-04 11:54 ` [PATCH 47/73] regulator: ab8500: Update AB9540 init masks Lee Jones
2013-02-04 11:54 ` [PATCH 48/73] regulator: ab8500: Use regulator_list_voltage_table() Lee Jones
2013-02-04 11:54 ` [PATCH 49/73] regulator: ab8500: Fix vsdio parameters for AB8540 based platforms Lee Jones
2013-02-04 11:54 ` [PATCH 50/73] regulator: ab8500: Correct regulator id values Lee Jones
2013-02-04 11:54 ` [PATCH 51/73] regulator: ab8500: Regulator vaux8 not declared using correct name Lee Jones
2013-02-04 11:54 ` [PATCH 52/73] ARM ux500: Remove external regulators from AB8505 init data Lee Jones
2013-02-05 15:22 ` Linus Walleij
2013-02-04 11:54 ` [PATCH 53/73] regulator: ab8500: Don't register external regulators on AB8505 Lee Jones
2013-02-04 11:54 ` [PATCH 54/73] regulator: ab8500: Add voltage selection for AUDIO and ANA " Lee Jones
2013-02-04 11:54 ` [PATCH 55/73] regulator: ab8500: Provide ExtSupply register init values for AB8505 Lee Jones
2013-02-04 11:54 ` [PATCH 56/73] regulator: ab8500: Also check for AB8505 based platforms Lee Jones
2013-02-04 11:54 ` [PATCH 57/73] regulator: ab8500: Remove surplus include of id.h Lee Jones
2013-02-04 11:54 ` [PATCH 58/73] regulator: ab8500: Add new operations for Vaux3 Lee Jones
2013-02-04 11:54 ` [PATCH 59/73] regulator: ab8500: Change mode fix for LDO USB Lee Jones
2013-02-04 11:54 ` [PATCH 60/73] ARM: ux500: regulators: Add LDO USB consumer Lee Jones
2013-02-05 15:21 ` Linus Walleij
2013-02-04 11:54 ` [PATCH 61/73] regulator: ab8500: Default value on LDO USB to HP Lee Jones
2013-02-04 11:54 ` [PATCH 62/73] regulator: ab8500: Remove vusb from AB8540 regulator framework Lee Jones
2013-02-04 11:54 ` [PATCH 63/73] regulator: ab8500: Add mode operation for v-amic Lee Jones
2013-02-04 11:54 ` [PATCH 64/73] regulator: ab8500: Update vdmic, vamic[1|2] parameters for AB8540 Lee Jones
2013-02-04 11:54 ` [PATCH 65/73] regulator: ab8500: Update VAna supply management for the AB9540 Lee Jones
2013-02-04 11:54 ` [PATCH 66/73] regulator: ab8500-ext: Adapt regulator registration for newly changed API Lee Jones
2013-02-04 11:54 ` [PATCH 67/73] regulator: ab8500: Use a struct to select the good regulator configuration Lee Jones
2013-02-04 11:54 ` [PATCH 68/73] regulator: ab8500: Provide DT support for additional platforms Lee Jones
2013-02-04 11:54 ` [PATCH 69/73] regulator: ab8500: Introduce aux5, aux6 regulators for AB8540 Lee Jones
2013-02-04 11:54 ` [PATCH 70/73] regulator: ab8500: Set enable enable_time in regulator_desc Lee Jones
2013-02-04 11:54 ` [PATCH 71/73] regulator: ab8500: Remove the need for a 'delay' property Lee Jones
2013-02-04 11:54 ` [PATCH 72/73] regulator: ab8500: Use regulator_list_voltage_table() to look-up voltages Lee Jones
2013-02-04 11:54 ` [PATCH 73/73] ARM: ux500: Pass regulator platform data using the new format Lee Jones
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1359978868-28736-10-git-send-email-lee.jones@linaro.org \
--to=lee.jones@linaro.org \
--cc=bengt.g.jonsson@stericsson.com \
--cc=broonie@opensource.wolfsonmicro.com \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®