[PATCH 0/6] hisi_sas: Some misc patches

[PATCH 0/6] hisi_sas: Some misc patches

[John Garry]

The patchset contains some misc patches for the driver, including:
- Workaround for acute scenario of SMP/internal IO timeout and reset racing
- Clear Affiliation for STP target port (from Luo Jiaxing and Xiang Chen)
- Fix PHY negotiated linkrate value for when PHY down
- Some init reg config changes
- Add support to coalesce and print PHY errors
- A tidy-up patch

John Garry (1):
  scsi: hisi_sas: Set PHY linkrate when disconnected

Xiang Chen (4):
  scsi: hisi_sas: Change return variable type in phy_up_v3_hw()
  scsi: hisi_sas: Fix a timeout race of driver internal and SMP IO
  scsi: hisi_sas: Send HARD RESET to clear the previous affiliation of
    STP target port
  scsi: hisi_sas: Change SERDES_CFG init value to increase reliability
    of HiLink

Xiaofei Tan (1):
  scsi: hisi_sas: print PHY RX errors count for later revision of v3 hw

 drivers/scsi/hisi_sas/hisi_sas.h       |  8 +++
 drivers/scsi/hisi_sas/hisi_sas_main.c  | 57 +++++++++++++++--
 drivers/scsi/hisi_sas/hisi_sas_v2_hw.c |  1 +
 drivers/scsi/hisi_sas/hisi_sas_v3_hw.c | 89 ++++++++++++++++++--------
 4 files changed, 125 insertions(+), 30 deletions(-)

-- 
2.17.1

[PATCH 1/6] scsi: hisi_sas: Change return variable type in phy_up_v3_hw()

[John Garry]

From: Xiang Chen <chenxiang66@hisilicon.com>

According to the tool fortify, phy_up_v3_hw() returns signed
value, while it should return an unsigned value.

So change variable "res" from int to irq_return_t.

Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
---
 drivers/scsi/hisi_sas/hisi_sas_v3_hw.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/scsi/hisi_sas/hisi_sas_v3_hw.c b/drivers/scsi/hisi_sas/hisi_sas_v3_hw.c
index 00738d0673fe..151a102c4cc7 100644
--- a/drivers/scsi/hisi_sas/hisi_sas_v3_hw.c
+++ b/drivers/scsi/hisi_sas/hisi_sas_v3_hw.c
@@ -1344,7 +1344,8 @@ static void prep_abort_v3_hw(struct hisi_hba *hisi_hba,
 
 static irqreturn_t phy_up_v3_hw(int phy_no, struct hisi_hba *hisi_hba)
 {
-	int i, res;
+	int i;
+	irqreturn_t res;
 	u32 context, port_id, link_rate;
 	struct hisi_sas_phy *phy = &hisi_hba->phy[phy_no];
 	struct asd_sas_phy *sas_phy = &phy->sas_phy;
-- 
2.17.1

[PATCH 2/6] scsi: hisi_sas: Fix a timeout race of driver internal and SMP IO

[John Garry]

From: Xiang Chen <chenxiang66@hisilicon.com>

For internal IO and SMP IO, there is a time-out timer for them. In the
timer handler, it checks whether IO is done according to the flag
task->task_state_lock.

There is an issue which may cause system suspended: internal IO or SMP IO
is sent, but at that time because of hardware exception (such as inject
2Bit ECC error), so IO is not completed and also not timeout. But, at that
time, the SAS controller reset occurs to recover system. It will release
the resource and set the status of IO to be SAS_TASK_STATE_DONE, so when
IO timeout, it will never complete the completion of IO and wait for ever.

[  729.123632] Call trace:
[  729.126791] [<ffff00000808655c>] __switch_to+0x94/0xa8
[  729.133106] [<ffff000008d96e98>] __schedule+0x1e8/0x7fc
[  729.138975] [<ffff000008d974e0>] schedule+0x34/0x8c
[  729.144401] [<ffff000008d9b000>] schedule_timeout+0x1d8/0x3cc
[  729.150690] [<ffff000008d98218>] wait_for_common+0xdc/0x1a0
[  729.157101] [<ffff000008d98304>] wait_for_completion+0x28/0x34
[  729.165973] [<ffff000000dcefb4>] hisi_sas_internal_task_abort+0x2a0/0x424 [hisi_sas_test_main]
[  729.176447] [<ffff000000dd18f4>] hisi_sas_abort_task+0x244/0x2d8 [hisi_sas_test_main]
[  729.185258] [<ffff000008971714>] sas_eh_handle_sas_errors+0x1c8/0x7b8
[  729.192391] [<ffff000008972774>] sas_scsi_recover_host+0x130/0x398
[  729.199237] [<ffff00000894d8a8>] scsi_error_handler+0x148/0x5c0
[  729.206009] [<ffff0000080f4118>] kthread+0x10c/0x138
[  729.211563] [<ffff0000080855dc>] ret_from_fork+0x10/0x18

To solve the issue, callback function task_done of those IOs need to be
called when on SAS controller reset.

Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
---
 drivers/scsi/hisi_sas/hisi_sas_main.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/scsi/hisi_sas/hisi_sas_main.c b/drivers/scsi/hisi_sas/hisi_sas_main.c
index 923296653ed7..dd03dcbd3786 100644
--- a/drivers/scsi/hisi_sas/hisi_sas_main.c
+++ b/drivers/scsi/hisi_sas/hisi_sas_main.c
@@ -980,7 +980,8 @@ static void hisi_sas_do_release_task(struct hisi_hba *hisi_hba, struct sas_task
 		spin_lock_irqsave(&task->task_state_lock, flags);
 		task->task_state_flags &=
 			~(SAS_TASK_STATE_PENDING | SAS_TASK_AT_INITIATOR);
-		task->task_state_flags |= SAS_TASK_STATE_DONE;
+		if (!slot->is_internal && task->task_proto != SAS_PROTOCOL_SMP)
+			task->task_state_flags |= SAS_TASK_STATE_DONE;
 		spin_unlock_irqrestore(&task->task_state_lock, flags);
 	}
 
-- 
2.17.1

[PATCH 3/6] scsi: hisi_sas: print PHY RX errors count for later revision of v3 hw

[John Garry]

From: Xiaofei Tan <tanxiaofei@huawei.com>

The later revision of v3 hw has added an function of interrupt coalesce
according to time for PHY RX errors. We set the coalesce time to 1s.
Then we print PHY RX errors count when PHY RX errors happen, and don't
need to worry that there may be too much log prints.

Besides, we use hisi_sas_phy.lock to protect error count value. Because
we update them by calling phy_get_events_v3_hw(), which is also used by
core driver (for get PHY events function).

We relocate phy_get_events_v3_hw() to avoid a further declaration.

Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
---
 drivers/scsi/hisi_sas/hisi_sas.h       |  1 +
 drivers/scsi/hisi_sas/hisi_sas_v3_hw.c | 84 ++++++++++++++++++--------
 2 files changed, 60 insertions(+), 25 deletions(-)

diff --git a/drivers/scsi/hisi_sas/hisi_sas.h b/drivers/scsi/hisi_sas/hisi_sas.h
index 6c87bd34509a..515aee9318a4 100644
--- a/drivers/scsi/hisi_sas/hisi_sas.h
+++ b/drivers/scsi/hisi_sas/hisi_sas.h
@@ -161,6 +161,7 @@ struct hisi_sas_phy {
 	u8		in_reset;
 	u8		reserved[2];
 	u32		phy_type;
+	u32		code_violation_err_count;
 	enum sas_linkrate	minimum_linkrate;
 	enum sas_linkrate	maximum_linkrate;
 };
diff --git a/drivers/scsi/hisi_sas/hisi_sas_v3_hw.c b/drivers/scsi/hisi_sas/hisi_sas_v3_hw.c
index 151a102c4cc7..720721196b12 100644
--- a/drivers/scsi/hisi_sas/hisi_sas_v3_hw.c
+++ b/drivers/scsi/hisi_sas/hisi_sas_v3_hw.c
@@ -181,6 +181,8 @@
 #define CHL_INT1_DMAC_RX_AXI_RD_ERR_OFF	22
 #define CHL_INT2			(PORT_BASE + 0x1bc)
 #define CHL_INT2_SL_IDAF_TOUT_CONF_OFF	0
+#define CHL_INT2_RX_DISP_ERR_OFF	28
+#define CHL_INT2_RX_CODE_ERR_OFF	29
 #define CHL_INT2_RX_INVLD_DW_OFF	30
 #define CHL_INT2_STP_LINK_TIMEOUT_OFF	31
 #define CHL_INT0_MSK			(PORT_BASE + 0x1c0)
@@ -544,6 +546,8 @@ static void init_reg_v3_hw(struct hisi_hba *hisi_hba)
 		hisi_sas_phy_write32(hisi_hba, i, STP_LINK_TIMER, 0x7f7a120);
 		hisi_sas_phy_write32(hisi_hba, i, CON_CFG_DRIVER, 0x2a0a01);
 		hisi_sas_phy_write32(hisi_hba, i, SAS_SSP_CON_TIMER_CFG, 0x32);
+		hisi_sas_phy_write32(hisi_hba, i, SAS_EC_INT_COAL_TIME,
+				     0x30f4240);
 		/* used for 12G negotiate */
 		hisi_sas_phy_write32(hisi_hba, i, COARSETUNE_TIME, 0x1e);
 		hisi_sas_phy_write32(hisi_hba, i, AIP_LIMIT, 0x2ffff);
@@ -1576,6 +1580,39 @@ static void handle_chl_int1_v3_hw(struct hisi_hba *hisi_hba, int phy_no)
 	hisi_sas_phy_write32(hisi_hba, phy_no, CHL_INT1, irq_value);
 }
 
+static void phy_get_events_v3_hw(struct hisi_hba *hisi_hba, int phy_no)
+{
+	struct hisi_sas_phy *phy = &hisi_hba->phy[phy_no];
+	struct asd_sas_phy *sas_phy = &phy->sas_phy;
+	struct sas_phy *sphy = sas_phy->phy;
+	unsigned long flags;
+	u32 reg_value;
+
+	spin_lock_irqsave(&phy->lock, flags);
+
+	/* loss dword sync */
+	reg_value = hisi_sas_phy_read32(hisi_hba, phy_no, ERR_CNT_DWS_LOST);
+	sphy->loss_of_dword_sync_count += reg_value;
+
+	/* phy reset problem */
+	reg_value = hisi_sas_phy_read32(hisi_hba, phy_no, ERR_CNT_RESET_PROB);
+	sphy->phy_reset_problem_count += reg_value;
+
+	/* invalid dword */
+	reg_value = hisi_sas_phy_read32(hisi_hba, phy_no, ERR_CNT_INVLD_DW);
+	sphy->invalid_dword_count += reg_value;
+
+	/* disparity err */
+	reg_value = hisi_sas_phy_read32(hisi_hba, phy_no, ERR_CNT_DISP_ERR);
+	sphy->running_disparity_error_count += reg_value;
+
+	/* code violation error */
+	reg_value = hisi_sas_phy_read32(hisi_hba, phy_no, ERR_CNT_CODE_ERR);
+	phy->code_violation_err_count += reg_value;
+
+	spin_unlock_irqrestore(&phy->lock, flags);
+}
+
 static void handle_chl_int2_v3_hw(struct hisi_hba *hisi_hba, int phy_no)
 {
 	u32 irq_msk = hisi_sas_phy_read32(hisi_hba, phy_no, CHL_INT2_MSK);
@@ -1583,6 +1620,9 @@ static void handle_chl_int2_v3_hw(struct hisi_hba *hisi_hba, int phy_no)
 	struct hisi_sas_phy *phy = &hisi_hba->phy[phy_no];
 	struct pci_dev *pci_dev = hisi_hba->pci_dev;
 	struct device *dev = hisi_hba->dev;
+	static const u32 msk = BIT(CHL_INT2_RX_DISP_ERR_OFF) |
+			BIT(CHL_INT2_RX_CODE_ERR_OFF) |
+			BIT(CHL_INT2_RX_INVLD_DW_OFF);
 
 	irq_value &= ~irq_msk;
 	if (!irq_value)
@@ -1603,6 +1643,25 @@ static void handle_chl_int2_v3_hw(struct hisi_hba *hisi_hba, int phy_no)
 			hisi_sas_notify_phy_event(phy, HISI_PHYE_LINK_RESET);
 	}
 
+	if (pci_dev->revision > 0x20 && (irq_value & msk)) {
+		struct asd_sas_phy *sas_phy = &phy->sas_phy;
+		struct sas_phy *sphy = sas_phy->phy;
+
+		phy_get_events_v3_hw(hisi_hba, phy_no);
+
+		if (irq_value & BIT(CHL_INT2_RX_INVLD_DW_OFF))
+			dev_info(dev, "phy%d invalid dword cnt:   %u\n", phy_no,
+				 sphy->invalid_dword_count);
+
+		if (irq_value & BIT(CHL_INT2_RX_CODE_ERR_OFF))
+			dev_info(dev, "phy%d code violation cnt:  %u\n", phy_no,
+				 phy->code_violation_err_count);
+
+		if (irq_value & BIT(CHL_INT2_RX_DISP_ERR_OFF))
+			dev_info(dev, "phy%d disparity error cnt: %u\n", phy_no,
+				 sphy->running_disparity_error_count);
+	}
+
 	if ((irq_value & BIT(CHL_INT2_RX_INVLD_DW_OFF)) &&
 	    (pci_dev->revision == 0x20)) {
 		u32 reg_value;
@@ -2231,31 +2290,6 @@ static u32 get_phys_state_v3_hw(struct hisi_hba *hisi_hba)
 	return hisi_sas_read32(hisi_hba, PHY_STATE);
 }
 
-static void phy_get_events_v3_hw(struct hisi_hba *hisi_hba, int phy_no)
-{
-	struct hisi_sas_phy *phy = &hisi_hba->phy[phy_no];
-	struct asd_sas_phy *sas_phy = &phy->sas_phy;
-	struct sas_phy *sphy = sas_phy->phy;
-	u32 reg_value;
-
-	/* loss dword sync */
-	reg_value = hisi_sas_phy_read32(hisi_hba, phy_no, ERR_CNT_DWS_LOST);
-	sphy->loss_of_dword_sync_count += reg_value;
-
-	/* phy reset problem */
-	reg_value = hisi_sas_phy_read32(hisi_hba, phy_no, ERR_CNT_RESET_PROB);
-	sphy->phy_reset_problem_count += reg_value;
-
-	/* invalid dword */
-	reg_value = hisi_sas_phy_read32(hisi_hba, phy_no, ERR_CNT_INVLD_DW);
-	sphy->invalid_dword_count += reg_value;
-
-	/* disparity err */
-	reg_value = hisi_sas_phy_read32(hisi_hba, phy_no, ERR_CNT_DISP_ERR);
-	sphy->running_disparity_error_count += reg_value;
-
-}
-
 static int disable_host_v3_hw(struct hisi_hba *hisi_hba)
 {
 	struct device *dev = hisi_hba->dev;
-- 
2.17.1

[PATCH 4/6] scsi: hisi_sas: Set PHY linkrate when disconnected

[John Garry]

When the PHY comes down, we currently do not set the negotiated linkrate:
root@(none)$ pwd
/sys/class/sas_phy/phy-0:0
root@(none)$ more enable
1
root@(none)$ more negotiated_linkrate
12.0 Gbit
root@(none)$ echo 0 > enable
root@(none)$ more negotiated_linkrate
12.0 Gbit
root@(none)$

This patch fixes the driver code to set it properly when the PHY comes
down.

If the PHY had been enabled, then set unknown; otherwise, flag as
disabled.

The logical place to set the negotiated linkrate for this scenario is PHY
down routine, which is called from the PHY down ISR.

However, it is not possible to know if the PHY comes down due to PHY
disable or loss of link, as sas_phy.enabled member is not set until after
the transport disable routine is complete, which races with the PHY down
ISR.

As an imperfect solution, use sas_phy_data.enable as the flag to know if
the PHY is down due to disable. It's imperfect, as sas_phy_data is
internal to libsas.

I can't see another way without adding a new field to hisi_sas_phy and
managing it, or changing SCSI SAS transport.

Signed-off-by: John Garry <john.garry@huawei.com>
---
 drivers/scsi/hisi_sas/hisi_sas_main.c | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/drivers/scsi/hisi_sas/hisi_sas_main.c b/drivers/scsi/hisi_sas/hisi_sas_main.c
index dd03dcbd3786..d8204bc3931b 100644
--- a/drivers/scsi/hisi_sas/hisi_sas_main.c
+++ b/drivers/scsi/hisi_sas/hisi_sas_main.c
@@ -10,6 +10,7 @@
  */
 
 #include "hisi_sas.h"
+#include "../libsas/sas_internal.h"
 #define DRV_NAME "hisi_sas"
 
 #define DEV_IS_GONE(dev) \
@@ -2126,9 +2127,18 @@ static int hisi_sas_write_gpio(struct sas_ha_struct *sha, u8 reg_type,
 
 static void hisi_sas_phy_disconnected(struct hisi_sas_phy *phy)
 {
+	struct asd_sas_phy *sas_phy = &phy->sas_phy;
+	struct sas_phy *sphy = sas_phy->phy;
+	struct sas_phy_data *d = sphy->hostdata;
+
 	phy->phy_attached = 0;
 	phy->phy_type = 0;
 	phy->port = NULL;
+
+	if (d->enable)
+		sphy->negotiated_linkrate = SAS_LINK_RATE_UNKNOWN;
+	else
+		sphy->negotiated_linkrate = SAS_PHY_DISABLED;
 }
 
 void hisi_sas_phy_down(struct hisi_hba *hisi_hba, int phy_no, int rdy)
-- 
2.17.1

[PATCH 5/6] scsi: hisi_sas: Send HARD RESET to clear the previous affiliation of STP target port

[John Garry]

From: Xiang Chen <chenxiang66@hisilicon.com>

If we exchange SAS expander from one SAS controller to other SAS
controller without powering it down, the STP target port will maintain
previous affiliation and reject all subsequent connection requests from
other STP initiator ports with OPEN_REJECT (STP RESOURCES BUSY).

To solve this issue, send HARD RESET to clear the previous affiliation of
STP target port according to SPL (chapter 6.19.4).

We (re-)introduce dev status flag to know if to sleep in NEXUS reset code
or not for remote PHYs. The idea is that if the device is being
initialised, we don't require the delay, and caller would wait for link to
be established, cf. sas_ata_hard_reset().

Co-developed-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
---
 drivers/scsi/hisi_sas/hisi_sas.h       |  7 ++++
 drivers/scsi/hisi_sas/hisi_sas_main.c  | 44 ++++++++++++++++++++++++--
 drivers/scsi/hisi_sas/hisi_sas_v2_hw.c |  1 +
 3 files changed, 49 insertions(+), 3 deletions(-)

diff --git a/drivers/scsi/hisi_sas/hisi_sas.h b/drivers/scsi/hisi_sas/hisi_sas.h
index 515aee9318a4..9bfa9f12d81e 100644
--- a/drivers/scsi/hisi_sas/hisi_sas.h
+++ b/drivers/scsi/hisi_sas/hisi_sas.h
@@ -18,6 +18,7 @@
 #include <linux/dmapool.h>
 #include <linux/iopoll.h>
 #include <linux/lcm.h>
+#include <linux/libata.h>
 #include <linux/mfd/syscon.h>
 #include <linux/module.h>
 #include <linux/of_address.h>
@@ -94,6 +95,11 @@ enum {
 	PORT_TYPE_SATA = (1U << 0),
 };
 
+enum dev_status {
+	HISI_SAS_DEV_INIT,
+	HISI_SAS_DEV_NORMAL,
+};
+
 enum {
 	HISI_SAS_INT_ABT_CMD = 0,
 	HISI_SAS_INT_ABT_DEV = 1,
@@ -195,6 +201,7 @@ struct hisi_sas_device {
 	struct hisi_sas_dq	*dq;
 	struct list_head	list;
 	enum sas_device_type	dev_type;
+	enum dev_status dev_status;
 	int device_id;
 	int sata_idx;
 	spinlock_t lock; /* For protecting slots */
diff --git a/drivers/scsi/hisi_sas/hisi_sas_main.c b/drivers/scsi/hisi_sas/hisi_sas_main.c
index d8204bc3931b..d12924256964 100644
--- a/drivers/scsi/hisi_sas/hisi_sas_main.c
+++ b/drivers/scsi/hisi_sas/hisi_sas_main.c
@@ -708,6 +708,7 @@ static struct hisi_sas_device *hisi_sas_alloc_dev(struct domain_device *device)
 
 			hisi_hba->devices[i].device_id = i;
 			sas_dev = &hisi_hba->devices[i];
+			sas_dev->dev_status = HISI_SAS_DEV_INIT;
 			sas_dev->dev_type = device->dev_type;
 			sas_dev->hisi_hba = hisi_hba;
 			sas_dev->sas_device = device;
@@ -732,6 +733,8 @@ static int hisi_sas_init_device(struct domain_device *device)
 	struct hisi_sas_tmf_task tmf_task;
 	int retry = HISI_SAS_SRST_ATA_DISK_CNT;
 	struct hisi_hba *hisi_hba = dev_to_hisi_hba(device);
+	struct device *dev = hisi_hba->dev;
+	struct sas_phy *local_phy;
 
 	switch (device->dev_type) {
 	case SAS_END_DEVICE:
@@ -747,6 +750,31 @@ static int hisi_sas_init_device(struct domain_device *device)
 	case SAS_SATA_PM:
 	case SAS_SATA_PM_PORT:
 	case SAS_SATA_PENDING:
+		/*
+		 * send HARD RESET to clear previous affiliation of
+		 * STP target port
+		 */
+		local_phy = sas_get_local_phy(device);
+		if (!scsi_is_sas_phy_local(local_phy)) {
+			unsigned long deadline = ata_deadline(jiffies, 20000);
+			struct sata_device *sata_dev = &device->sata_dev;
+			struct ata_host *ata_host = sata_dev->ata_host;
+			struct ata_port_operations *ops = ata_host->ops;
+			struct ata_port *ap = sata_dev->ap;
+			struct ata_link *link;
+			unsigned int classes;
+
+			ata_for_each_link(link, ap, EDGE)
+				rc = ops->hardreset(link, &classes,
+						    deadline);
+		}
+		sas_put_local_phy(local_phy);
+		if (rc) {
+			dev_warn(dev, "SATA disk hardreset fail: 0x%x\n",
+				 rc);
+			return rc;
+		}
+
 		while (retry-- > 0) {
 			rc = hisi_sas_softreset_ata_disk(device);
 			if (!rc)
@@ -809,6 +837,7 @@ static int hisi_sas_dev_found(struct domain_device *device)
 	rc = hisi_sas_init_device(device);
 	if (rc)
 		goto err_out;
+	sas_dev->dev_status = HISI_SAS_DEV_NORMAL;
 	return 0;
 
 err_out:
@@ -1715,20 +1744,23 @@ static int hisi_sas_clear_aca(struct domain_device *device, u8 *lun)
 static int hisi_sas_debug_I_T_nexus_reset(struct domain_device *device)
 {
 	struct sas_phy *local_phy = sas_get_local_phy(device);
-	int rc, reset_type = (device->dev_type == SAS_SATA_DEV ||
-			(device->tproto & SAS_PROTOCOL_STP)) ? 0 : 1;
+	struct hisi_sas_device *sas_dev = device->lldd_dev;
 	struct hisi_hba *hisi_hba = dev_to_hisi_hba(device);
 	struct sas_ha_struct *sas_ha = &hisi_hba->sha;
 	struct asd_sas_phy *sas_phy = sas_ha->sas_phy[local_phy->number];
 	struct hisi_sas_phy *phy = container_of(sas_phy,
 			struct hisi_sas_phy, sas_phy);
 	DECLARE_COMPLETION_ONSTACK(phyreset);
+	int rc, reset_type;
 
 	if (scsi_is_sas_phy_local(local_phy)) {
 		phy->in_reset = 1;
 		phy->reset_completion = &phyreset;
 	}
 
+	reset_type = (sas_dev->dev_status == HISI_SAS_DEV_INIT ||
+		      !dev_is_sata(device)) ? 1 : 0;
+
 	rc = sas_phy_reset(local_phy, reset_type);
 	sas_put_local_phy(local_phy);
 
@@ -1744,8 +1776,13 @@ static int hisi_sas_debug_I_T_nexus_reset(struct domain_device *device)
 		/* report PHY down if timed out */
 		if (!ret)
 			hisi_sas_phy_down(hisi_hba, sas_phy->id, 0);
-	} else
+	} else if (sas_dev->dev_status != HISI_SAS_DEV_INIT) {
+		/*
+		 * If in init state, we rely on caller to wait for link to be
+		 * ready; otherwise, delay.
+		 */
 		msleep(2000);
+	}
 
 	return rc;
 }
@@ -2264,6 +2301,7 @@ int hisi_sas_alloc(struct hisi_hba *hisi_hba)
 	for (i = 0; i < HISI_SAS_MAX_DEVICES; i++) {
 		hisi_hba->devices[i].dev_type = SAS_PHY_UNUSED;
 		hisi_hba->devices[i].device_id = i;
+		hisi_hba->devices[i].dev_status = HISI_SAS_DEV_INIT;
 	}
 
 	for (i = 0; i < hisi_hba->queue_count; i++) {
diff --git a/drivers/scsi/hisi_sas/hisi_sas_v2_hw.c b/drivers/scsi/hisi_sas/hisi_sas_v2_hw.c
index e40cc6b3b67b..89160ab3efb0 100644
--- a/drivers/scsi/hisi_sas/hisi_sas_v2_hw.c
+++ b/drivers/scsi/hisi_sas/hisi_sas_v2_hw.c
@@ -868,6 +868,7 @@ hisi_sas_device *alloc_dev_quirk_v2_hw(struct domain_device *device)
 
 			hisi_hba->devices[i].device_id = i;
 			sas_dev = &hisi_hba->devices[i];
+			sas_dev->dev_status = HISI_SAS_DEV_INIT;
 			sas_dev->dev_type = device->dev_type;
 			sas_dev->hisi_hba = hisi_hba;
 			sas_dev->sas_device = device;
-- 
2.17.1

[PATCH 6/6] scsi: hisi_sas: Change SERDES_CFG init value to increase reliability of HiLink

[John Garry]

From: Xiang Chen <chenxiang66@hisilicon.com>

With default value of register SERDES_CFG, the link is not stable for some
special disks when running IO. According to HW guys' suggestion, need to
make the bit10~19 value of register SERDES_CFG the max value to increase
the reliability of the HiLink.

Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Yupeng Zhou <zhouyupeng1@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
---
 drivers/scsi/hisi_sas/hisi_sas_v3_hw.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/scsi/hisi_sas/hisi_sas_v3_hw.c b/drivers/scsi/hisi_sas/hisi_sas_v3_hw.c
index 720721196b12..e2f2c04355b9 100644
--- a/drivers/scsi/hisi_sas/hisi_sas_v3_hw.c
+++ b/drivers/scsi/hisi_sas/hisi_sas_v3_hw.c
@@ -129,6 +129,7 @@
 #define PHY_CTRL_RESET_MSK		(0x1 << PHY_CTRL_RESET_OFF)
 #define CMD_HDR_PIR_OFF			8
 #define CMD_HDR_PIR_MSK			(0x1 << CMD_HDR_PIR_OFF)
+#define SERDES_CFG			(PORT_BASE + 0x1c)
 #define SL_CFG				(PORT_BASE + 0x84)
 #define AIP_LIMIT			(PORT_BASE + 0x90)
 #define SL_CONTROL			(PORT_BASE + 0x94)
@@ -525,6 +526,7 @@ static void init_reg_v3_hw(struct hisi_hba *hisi_hba)
 		}
 		hisi_sas_phy_write32(hisi_hba, i, PROG_PHY_LINK_RATE,
 			prog_phy_link_rate);
+		hisi_sas_phy_write32(hisi_hba, i, SERDES_CFG, 0xffc00);
 		hisi_sas_phy_write32(hisi_hba, i, SAS_RX_TRAIN_TIMER, 0x13e80);
 		hisi_sas_phy_write32(hisi_hba, i, CHL_INT0, 0xffffffff);
 		hisi_sas_phy_write32(hisi_hba, i, CHL_INT1, 0xffffffff);
-- 
2.17.1

Re: [PATCH 0/6] hisi_sas: Some misc patches

[Martin K. Petersen]

John,

> The patchset contains some misc patches for the driver, including:
> - Workaround for acute scenario of SMP/internal IO timeout and reset racing
> - Clear Affiliation for STP target port (from Luo Jiaxing and Xiang Chen)
> - Fix PHY negotiated linkrate value for when PHY down
> - Some init reg config changes
> - Add support to coalesce and print PHY errors
> - A tidy-up patch

Applied to 5.1/scsi-queue, thanks!

-- 
Martin K. Petersen	Oracle Linux Engineering