ide-scsi driver trouble in ac15

ide-scsi driver trouble in ac15

[safemode]

I'm not entirely sure if this is ac15's fault or the preempt patch acting up. 
But this is very ide-scsi centric so i'm leaning towards ac15.  I burned a cd 
using my ide writer and it worked fine.  Then i went to burn another and the 
drive went into an infinite reset loop.  like this.
	SCSI bus is being reset for host 0 channel 0.
	scsi0 : channel 0 target 0 lun 0 request sense failed, performing reset.

reloading the modules does nothing but report this error. 
	SCSI subsystem driver Revision: 1.00
	scsi0 : SCSI host adapter emulation for IDE ATAPI devices
	scsi0 : channel 0 target 0 lun 0 request sense failed, performing reset.
	SCSI bus is being reset for host 0 channel 0.

Even though the modules were removed, the drive led is still blinking like it 
was writing.  If anyone needs some more info i'll try and get it. 
the cdr did detect and work correctly at boot. 

hardware:
    Promise ide controller : 
	PDC20262: chipset revision 1
	PDC20262: not 100% native mode: will probe irqs later
	PDC20262: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode.
    CDR: 
	hde: CREATIVE CD-RW RW8438E, ATAPI CD/DVD-ROM drive
	SCSI subsystem driver Revision: 1.00
	scsi0 : SCSI host adapter emulation for IDE ATAPI devices
  	Vendor: CREATIVE  Model:  CD-RW RW8438E    Rev: FC03
  	Type:   CD-ROM                             ANSI SCSI revision: 02
software:
    Cdrecord 1.10 (i686-pc-linux-gnu) Copyright (C) 1995-2001 Jörg Schilling
    linux-2.4.9-ac15-preempt-fix
     

Re: ide-scsi driver trouble in ac15

[Jorge Nerín]

safemode wrote:

>I'm not entirely sure if this is ac15's fault or the preempt patch acting up. 
>But this is very ide-scsi centric so i'm leaning towards ac15.  I burned a cd 
>using my ide writer and it worked fine.  Then i went to burn another and the 
>drive went into an infinite reset loop.  like this.
>	SCSI bus is being reset for host 0 channel 0.
>	scsi0 : channel 0 target 0 lun 0 request sense failed, performing reset.
>
>reloading the modules does nothing but report this error. 
>	SCSI subsystem driver Revision: 1.00
>	scsi0 : SCSI host adapter emulation for IDE ATAPI devices
>	scsi0 : channel 0 target 0 lun 0 request sense failed, performing reset.
>	SCSI bus is being reset for host 0 channel 0.
>
>Even though the modules were removed, the drive led is still blinking like it 
>was writing.  If anyone needs some more info i'll try and get it. 
>the cdr did detect and work correctly at boot. 
>
>hardware:
>    Promise ide controller : 
>	PDC20262: chipset revision 1
>	PDC20262: not 100% native mode: will probe irqs later
>	PDC20262: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode.
>    CDR: 
>	hde: CREATIVE CD-RW RW8438E, ATAPI CD/DVD-ROM drive
>	SCSI subsystem driver Revision: 1.00
>	scsi0 : SCSI host adapter emulation for IDE ATAPI devices
>  	Vendor: CREATIVE  Model:  CD-RW RW8438E    Rev: FC03
>  	Type:   CD-ROM                             ANSI SCSI revision: 02
>software:
>    Cdrecord 1.10 (i686-pc-linux-gnu) Copyright (C) 1995-2001 Jörg Schilling
>    linux-2.4.9-ac15-preempt-fix
>
It also happened to me with ac10, ide-scsi, CD-RW is a Samsung 8x, and I 
was writing a audio cd, when it finished writing the track 8 of 18 it 
entered the loop, since then I couldn't eject the cd, neither eject 
/dev/hdb, nor cdrecord -eject, nor the eject button, I had to reboot.

My system is a 2x200mmx smp all ide.

-- 
Jorge Nerin
<comandante@zaralinux.com>

Re: ide-scsi driver trouble in ac15

[safemode]

On Friday 28 September 2001 08:15, Jorge Nerín wrote:
> safemode wrote:
> >I'm not entirely sure if this is ac15's fault or the preempt patch acting
> > up. But this is very ide-scsi centric so i'm leaning towards ac15.  I
> > burned a cd using my ide writer and it worked fine.  Then i went to burn
> > another and the drive went into an infinite reset loop.  like this.
> >	SCSI bus is being reset for host 0 channel 0.
> >	scsi0 : channel 0 target 0 lun 0 request sense failed, performing reset.
> >
> >reloading the modules does nothing but report this error.
> >	SCSI subsystem driver Revision: 1.00
> >	scsi0 : SCSI host adapter emulation for IDE ATAPI devices
> >	scsi0 : channel 0 target 0 lun 0 request sense failed, performing reset.
> >	SCSI bus is being reset for host 0 channel 0.
> >
> >Even though the modules were removed, the drive led is still blinking like
> > it was writing.  If anyone needs some more info i'll try and get it. the
> > cdr did detect and work correctly at boot.
> >
> >hardware:
> >    Promise ide controller :
> >	PDC20262: chipset revision 1
> >	PDC20262: not 100% native mode: will probe irqs later
> >	PDC20262: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode.
> >    CDR:
> >	hde: CREATIVE CD-RW RW8438E, ATAPI CD/DVD-ROM drive
> >	SCSI subsystem driver Revision: 1.00
> >	scsi0 : SCSI host adapter emulation for IDE ATAPI devices
> >  	Vendor: CREATIVE  Model:  CD-RW RW8438E    Rev: FC03
> >  	Type:   CD-ROM                             ANSI SCSI revision: 02
> >software:
> >    Cdrecord 1.10 (i686-pc-linux-gnu) Copyright (C) 1995-2001 Jörg
> > Schilling linux-2.4.9-ac15-preempt-fix
>
> It also happened to me with ac10, ide-scsi, CD-RW is a Samsung 8x, and I
> was writing a audio cd, when it finished writing the track 8 of 18 it
> entered the loop, since then I couldn't eject the cd, neither eject
> /dev/hdb, nor cdrecord -eject, nor the eject button, I had to reboot.
>
> My system is a 2x200mmx smp all ide.
Seems to be an interesting coincidence, i had just written an audio cd and 
was writing another when it happened. Only it happened to me when just 
beginning the cd.  Had to reboot. The cd was fine, it never actually got to 
writing, so i used it after i  had rebooted the system and it worked fine.  

Re: ide-scsi driver trouble in ac15

[bill davidsen]

In article <3BB469E1.9090205@juridicas.com> jnerin@juridicas.com wrote:

	[ ide-scsi problens ]

>It also happened to me with ac10, ide-scsi, CD-RW is a Samsung 8x, and =
>I=20
>was writing a audio cd, when it finished writing the track 8 of 18 it=20
>entered the loop, since then I couldn't eject the cd, neither eject=20
>/dev/hdb, nor cdrecord -eject, nor the eject button, I had to reboot.
>
>My system is a 2x200mmx smp all ide.

Don't see it on a P-II-400 (Dell Dimension 400). The Yamaha on-board
sound doesn't work, but it never did, it just thinks it is, sound apps
work fine but never produce output.

I do note that the sound modules noted in modules.conf didn't load and
need to be hand loaded...

-- 
bill davidsen <davidsen@tmr.com>
 "If I were a diplomat, in the best case I'd go hungry.  In the worst
  case, people would die."
		-- Robert Lipe