[PATCH AUTOSEL 6.1 01/47] phy: qcom-snps-femto-v2: keep cfg_ahb_clk enabled during runtime suspend

[PATCH AUTOSEL 6.1 01/47] phy: qcom-snps-femto-v2: keep cfg_ahb_clk enabled during runtime suspend

[Sasha Levin]

From: Adrien Thierry <athierry@redhat.com>

[ Upstream commit 45d89a344eb46db9dce851c28e14f5e3c635c251 ]

In the dwc3 core, both system and runtime suspend end up calling
dwc3_suspend_common(). From there, what happens for the PHYs depends on
the USB mode and whether the controller is entering system or runtime
suspend.

HOST mode:
  (1) system suspend on a non-wakeup-capable controller

  The [1] if branch is taken. dwc3_core_exit() is called, which ends up
  calling phy_power_off() and phy_exit(). Those two functions decrease the
  PM runtime count at some point, so they will trigger the PHY runtime
  sleep (assuming the count is right).

  (2) runtime suspend / system suspend on a wakeup-capable controller

  The [1] branch is not taken. dwc3_suspend_common() calls
  phy_pm_runtime_put_sync(). Assuming the ref count is right, the PHY
  runtime suspend op is called.

DEVICE mode:
  dwc3_core_exit() is called on both runtime and system sleep
  unless the controller is already runtime suspended.

OTG mode:
  (1) system suspend : dwc3_core_exit() is called

  (2) runtime suspend : do nothing

In host mode, the code seems to make a distinction between 1) runtime
sleep / system sleep for wakeup-capable controller, and 2) system sleep
for non-wakeup-capable controller, where phy_power_off() and phy_exit()
are only called for the latter. This suggests the PHY is not supposed to
be in a fully powered-off state for runtime sleep and system sleep for
wakeup-capable controller.

Moreover, downstream, cfg_ahb_clk only gets disabled for system suspend.
The clocks are disabled by phy->set_suspend() [2] which is only called
in the system sleep path through dwc3_core_exit() [3].

With that in mind, don't disable the clocks during the femto PHY runtime
suspend callback. The clocks will only be disabled during system suspend
for non-wakeup-capable controllers, through dwc3_core_exit().

[1] https://elixir.bootlin.com/linux/v6.4/source/drivers/usb/dwc3/core.c#L1988
[2] https://git.codelinaro.org/clo/la/kernel/msm-5.4/-/blob/LV.AU.1.2.1.r2-05300-gen3meta.0/drivers/usb/phy/phy-msm-snps-hs.c#L524
[3] https://git.codelinaro.org/clo/la/kernel/msm-5.4/-/blob/LV.AU.1.2.1.r2-05300-gen3meta.0/drivers/usb/dwc3/core.c#L1915

Signed-off-by: Adrien Thierry <athierry@redhat.com>
Link: https://lore.kernel.org/r/20230629144542.14906-2-athierry@redhat.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c | 9 ---------
 1 file changed, 9 deletions(-)

diff --git a/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c b/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
index a590635962140..1d45029b19cd5 100644
--- a/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
+++ b/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
@@ -165,22 +165,13 @@ static int qcom_snps_hsphy_suspend(struct qcom_snps_hsphy *hsphy)
 					   0, USB2_AUTO_RESUME);
 	}
 
-	clk_disable_unprepare(hsphy->cfg_ahb_clk);
 	return 0;
 }
 
 static int qcom_snps_hsphy_resume(struct qcom_snps_hsphy *hsphy)
 {
-	int ret;
-
 	dev_dbg(&hsphy->phy->dev, "Resume QCOM SNPS PHY, mode\n");
 
-	ret = clk_prepare_enable(hsphy->cfg_ahb_clk);
-	if (ret) {
-		dev_err(&hsphy->phy->dev, "failed to enable cfg ahb clock\n");
-		return ret;
-	}
-
 	return 0;
 }
 
-- 
2.40.1

[PATCH AUTOSEL 6.1 02/47] phy: qcom-snps-femto-v2: use qcom_snps_hsphy_suspend/resume error code

[Sasha Levin]

From: Adrien Thierry <athierry@redhat.com>

[ Upstream commit 8932089b566c24ea19b57e37704c492678de1420 ]

The return value from qcom_snps_hsphy_suspend/resume is not used. Make
sure qcom_snps_hsphy_runtime_suspend/resume return this value as well.

Signed-off-by: Adrien Thierry <athierry@redhat.com>
Link: https://lore.kernel.org/r/20230629144542.14906-4-athierry@redhat.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)

diff --git a/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c b/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
index 1d45029b19cd5..d73c7e2208485 100644
--- a/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
+++ b/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
@@ -182,8 +182,7 @@ static int __maybe_unused qcom_snps_hsphy_runtime_suspend(struct device *dev)
 	if (!hsphy->phy_initialized)
 		return 0;
 
-	qcom_snps_hsphy_suspend(hsphy);
-	return 0;
+	return qcom_snps_hsphy_suspend(hsphy);
 }
 
 static int __maybe_unused qcom_snps_hsphy_runtime_resume(struct device *dev)
@@ -193,8 +192,7 @@ static int __maybe_unused qcom_snps_hsphy_runtime_resume(struct device *dev)
 	if (!hsphy->phy_initialized)
 		return 0;
 
-	qcom_snps_hsphy_resume(hsphy);
-	return 0;
+	return qcom_snps_hsphy_resume(hsphy);
 }
 
 static int qcom_snps_hsphy_set_mode(struct phy *phy, enum phy_mode mode,
-- 
2.40.1

[PATCH AUTOSEL 6.1 03/47] media: amphion: use dev_err_probe

[Sasha Levin]

From: Alexander Stein <alexander.stein@ew.tq-group.com>

[ Upstream commit 517f088385e1b8015606143e6212cb30f8714070 ]

This simplifies the code and silences -517 error messages. Also
the reason is listed in /sys/kernel/debug/devices_deferred.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: ming_qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/platform/amphion/vpu_mbox.c | 9 ++++-----
 1 file changed, 4 insertions(+), 5 deletions(-)

diff --git a/drivers/media/platform/amphion/vpu_mbox.c b/drivers/media/platform/amphion/vpu_mbox.c
index bf759eb2fd46d..b6d5b4844f672 100644
--- a/drivers/media/platform/amphion/vpu_mbox.c
+++ b/drivers/media/platform/amphion/vpu_mbox.c
@@ -46,11 +46,10 @@ static int vpu_mbox_request_channel(struct device *dev, struct vpu_mbox *mbox)
 	cl->rx_callback = vpu_mbox_rx_callback;
 
 	ch = mbox_request_channel_byname(cl, mbox->name);
-	if (IS_ERR(ch)) {
-		dev_err(dev, "Failed to request mbox chan %s, ret : %ld\n",
-			mbox->name, PTR_ERR(ch));
-		return PTR_ERR(ch);
-	}
+	if (IS_ERR(ch))
+		return dev_err_probe(dev, PTR_ERR(ch),
+				     "Failed to request mbox chan %s\n",
+				     mbox->name);
 
 	mbox->ch = ch;
 	return 0;
-- 
2.40.1

[PATCH AUTOSEL 6.1 04/47] media: pulse8-cec: handle possible ping error

[Sasha Levin]

From: Dmitry Antipov <dmantipov@yandex.ru>

[ Upstream commit 92cbf865ea2e0f2997ff97815c6db182eb23df1b ]

Handle (and warn about) possible error waiting for MSGCODE_PING result.

Found by Linux Verification Center (linuxtesting.org) with SVACE.

Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/cec/usb/pulse8/pulse8-cec.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)

diff --git a/drivers/media/cec/usb/pulse8/pulse8-cec.c b/drivers/media/cec/usb/pulse8/pulse8-cec.c
index 04b13cdc38d2c..ba67587bd43ec 100644
--- a/drivers/media/cec/usb/pulse8/pulse8-cec.c
+++ b/drivers/media/cec/usb/pulse8/pulse8-cec.c
@@ -809,8 +809,11 @@ static void pulse8_ping_eeprom_work_handler(struct work_struct *work)
 
 	mutex_lock(&pulse8->lock);
 	cmd = MSGCODE_PING;
-	pulse8_send_and_wait(pulse8, &cmd, 1,
-			     MSGCODE_COMMAND_ACCEPTED, 0);
+	if (pulse8_send_and_wait(pulse8, &cmd, 1,
+				 MSGCODE_COMMAND_ACCEPTED, 0)) {
+		dev_warn(pulse8->dev, "failed to ping EEPROM\n");
+		goto unlock;
+	}
 
 	if (pulse8->vers < 2)
 		goto unlock;
-- 
2.40.1

[PATCH AUTOSEL 6.1 05/47] media: pci: cx23885: fix error handling for cx23885 ATSC boards

[Sasha Levin]

From: Nikolay Burykin <burikin@ivk.ru>

[ Upstream commit 4aaa96b59df5fac41ba891969df6b092061ea9d7 ]

After having been assigned to NULL value at cx23885-dvb.c:1202,
pointer '0' is dereferenced at cx23885-dvb.c:2469.

Found by Linux Verification Center (linuxtesting.org) with SVACE.

Signed-off-by: Nikolay Burykin <burikin@ivk.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/pci/cx23885/cx23885-dvb.c | 12 ------------
 1 file changed, 12 deletions(-)

diff --git a/drivers/media/pci/cx23885/cx23885-dvb.c b/drivers/media/pci/cx23885/cx23885-dvb.c
index 8fd5b6ef24282..7551ca4a322a4 100644
--- a/drivers/media/pci/cx23885/cx23885-dvb.c
+++ b/drivers/media/pci/cx23885/cx23885-dvb.c
@@ -2459,16 +2459,10 @@ static int dvb_register(struct cx23885_tsport *port)
 			request_module("%s", info.type);
 			client_tuner = i2c_new_client_device(&dev->i2c_bus[1].i2c_adap, &info);
 			if (!i2c_client_has_driver(client_tuner)) {
-				module_put(client_demod->dev.driver->owner);
-				i2c_unregister_device(client_demod);
-				port->i2c_client_demod = NULL;
 				goto frontend_detach;
 			}
 			if (!try_module_get(client_tuner->dev.driver->owner)) {
 				i2c_unregister_device(client_tuner);
-				module_put(client_demod->dev.driver->owner);
-				i2c_unregister_device(client_demod);
-				port->i2c_client_demod = NULL;
 				goto frontend_detach;
 			}
 			port->i2c_client_tuner = client_tuner;
@@ -2505,16 +2499,10 @@ static int dvb_register(struct cx23885_tsport *port)
 			request_module("%s", info.type);
 			client_tuner = i2c_new_client_device(&dev->i2c_bus[1].i2c_adap, &info);
 			if (!i2c_client_has_driver(client_tuner)) {
-				module_put(client_demod->dev.driver->owner);
-				i2c_unregister_device(client_demod);
-				port->i2c_client_demod = NULL;
 				goto frontend_detach;
 			}
 			if (!try_module_get(client_tuner->dev.driver->owner)) {
 				i2c_unregister_device(client_tuner);
-				module_put(client_demod->dev.driver->owner);
-				i2c_unregister_device(client_demod);
-				port->i2c_client_demod = NULL;
 				goto frontend_detach;
 			}
 			port->i2c_client_tuner = client_tuner;
-- 
2.40.1

[PATCH AUTOSEL 6.1 06/47] platform/x86: serial-multi-instantiate: Auto detect IRQ resource for CSC3551

[Sasha Levin]

From: David Xu <xuwd1@hotmail.com>

[ Upstream commit 676b7c5ecab36274442887ceadd6dee8248a244f ]

The current code assumes that the CSC3551(multiple cs35l41) always have
its interrupt pin connected to GPIO thus the IRQ can be acquired with
acpi_dev_gpio_irq_get. However on some newer laptop models this is no
longer the case as they have the CSC3551's interrupt pin connected to
APIC. This causes smi_i2c_probe to fail on these machines.

To support these machines, a new macro IRQ_RESOURCE_AUTO was introduced
for cs35l41 smi_node, and smi_get_irq function was modified so it tries
to get GPIO irq resource first and if failed, tries to get
APIC irq resource for cs35l41.

This patch affects only the cs35l41's probing and brings no negative
influence on machines that indeed have the cs35l41's interrupt pin
connected to GPIO.

Signed-off-by: David Xu <xuwd1@hotmail.com>
Link: https://lore.kernel.org/r/SY4P282MB18350CD8288687B87FFD2243E037A@SY4P282MB1835.AUSP282.PROD.OUTLOOK.COM
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 .../platform/x86/serial-multi-instantiate.c   | 21 +++++++++++++++----
 1 file changed, 17 insertions(+), 4 deletions(-)

diff --git a/drivers/platform/x86/serial-multi-instantiate.c b/drivers/platform/x86/serial-multi-instantiate.c
index 5362f1a7b77c5..85c9eabd85c08 100644
--- a/drivers/platform/x86/serial-multi-instantiate.c
+++ b/drivers/platform/x86/serial-multi-instantiate.c
@@ -21,6 +21,7 @@
 #define IRQ_RESOURCE_NONE	0
 #define IRQ_RESOURCE_GPIO	1
 #define IRQ_RESOURCE_APIC	2
+#define IRQ_RESOURCE_AUTO   3
 
 enum smi_bus_type {
 	SMI_I2C,
@@ -52,6 +53,18 @@ static int smi_get_irq(struct platform_device *pdev, struct acpi_device *adev,
 	int ret;
 
 	switch (inst->flags & IRQ_RESOURCE_TYPE) {
+	case IRQ_RESOURCE_AUTO:
+		ret = acpi_dev_gpio_irq_get(adev, inst->irq_idx);
+		if (ret > 0) {
+			dev_dbg(&pdev->dev, "Using gpio irq\n");
+			break;
+		}
+		ret = platform_get_irq(pdev, inst->irq_idx);
+		if (ret > 0) {
+			dev_dbg(&pdev->dev, "Using platform irq\n");
+			break;
+		}
+		break;
 	case IRQ_RESOURCE_GPIO:
 		ret = acpi_dev_gpio_irq_get(adev, inst->irq_idx);
 		break;
@@ -308,10 +321,10 @@ static const struct smi_node int3515_data = {
 
 static const struct smi_node cs35l41_hda = {
 	.instances = {
-		{ "cs35l41-hda", IRQ_RESOURCE_GPIO, 0 },
-		{ "cs35l41-hda", IRQ_RESOURCE_GPIO, 0 },
-		{ "cs35l41-hda", IRQ_RESOURCE_GPIO, 0 },
-		{ "cs35l41-hda", IRQ_RESOURCE_GPIO, 0 },
+		{ "cs35l41-hda", IRQ_RESOURCE_AUTO, 0 },
+		{ "cs35l41-hda", IRQ_RESOURCE_AUTO, 0 },
+		{ "cs35l41-hda", IRQ_RESOURCE_AUTO, 0 },
+		{ "cs35l41-hda", IRQ_RESOURCE_AUTO, 0 },
 		{}
 	},
 	.bus_type = SMI_AUTO_DETECT,
-- 
2.40.1

[PATCH AUTOSEL 6.1 07/47] 9p: virtio: fix unlikely null pointer deref in handle_rerror

[Sasha Levin]

From: Dominique Martinet <asmadeus@codewreck.org>

[ Upstream commit 13ade4ac5c28e8a014fa85278f5a4270b215f906 ]

handle_rerror can dereference the pages pointer, but it is not
necessarily set for small payloads.
In practice these should be filtered out by the size check, but
might as well double-check explicitly.

This fixes the following scan-build warnings:
net/9p/trans_virtio.c:401:24: warning: Dereference of null pointer [core.NullDereference]
                memcpy_from_page(to, *pages++, offs, n);
                                     ^~~~~~~~
net/9p/trans_virtio.c:406:23: warning: Dereference of null pointer (loaded from variable 'pages') [core.NullDereference]
        memcpy_from_page(to, *pages, offs, size);
                             ^~~~~~

Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
Signed-off-by: Eric Van Hensbergen <ericvh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/9p/trans_virtio.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/net/9p/trans_virtio.c b/net/9p/trans_virtio.c
index 3f3eb03cda7d6..6a4a29a2703de 100644
--- a/net/9p/trans_virtio.c
+++ b/net/9p/trans_virtio.c
@@ -385,7 +385,7 @@ static void handle_rerror(struct p9_req_t *req, int in_hdr_len,
 	void *to = req->rc.sdata + in_hdr_len;
 
 	// Fits entirely into the static data?  Nothing to do.
-	if (req->rc.size < in_hdr_len)
+	if (req->rc.size < in_hdr_len || !pages)
 		return;
 
 	// Really long error message?  Tough, truncate the reply.  Might get
-- 
2.40.1

[PATCH AUTOSEL 6.1 08/47] 9p: virtio: make sure 'offs' is initialized in zc_request

[Sasha Levin]

From: Dominique Martinet <asmadeus@codewreck.org>

[ Upstream commit 4a73edab69d3a6623f03817fe950a2d9585f80e4 ]

Similarly to the previous patch: offs can be used in handle_rerrors
without initializing on small payloads; in this case handle_rerrors will
not use it because of the size check, but it doesn't hurt to make sure
it is zero to please scan-build.

This fixes the following warning:
net/9p/trans_virtio.c:539:3: warning: 3rd function call argument is an uninitialized value [core.CallAndMessage]
                handle_rerror(req, in_hdr_len, offs, in_pages);
                ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
Signed-off-by: Eric Van Hensbergen <ericvh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/9p/trans_virtio.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/net/9p/trans_virtio.c b/net/9p/trans_virtio.c
index 6a4a29a2703de..3cf660d8a0a7b 100644
--- a/net/9p/trans_virtio.c
+++ b/net/9p/trans_virtio.c
@@ -429,7 +429,7 @@ p9_virtio_zc_request(struct p9_client *client, struct p9_req_t *req,
 	struct page **in_pages = NULL, **out_pages = NULL;
 	struct virtio_chan *chan = client->trans;
 	struct scatterlist *sgs[4];
-	size_t offs;
+	size_t offs = 0;
 	int need_drop = 0;
 	int kicked = 0;
 
-- 
2.40.1

[PATCH AUTOSEL 6.1 09/47] ksmbd: fix out of bounds in smb3_decrypt_req()

[Sasha Levin]

From: Namjae Jeon <linkinjeon@kernel.org>

[ Upstream commit dc318846f3dd54574a36ae97fc8d8b75dd7cdb1e ]

smb3_decrypt_req() validate if pdu_length is smaller than
smb2_transform_hdr size.

Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-21589
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 fs/smb/server/smb2pdu.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/fs/smb/server/smb2pdu.c b/fs/smb/server/smb2pdu.c
index 26cf73d664f94..c33249393ef36 100644
--- a/fs/smb/server/smb2pdu.c
+++ b/fs/smb/server/smb2pdu.c
@@ -8706,7 +8706,8 @@ int smb3_decrypt_req(struct ksmbd_work *work)
 	struct smb2_transform_hdr *tr_hdr = smb2_get_msg(buf);
 	int rc = 0;
 
-	if (buf_data_size < sizeof(struct smb2_hdr)) {
+	if (pdu_length < sizeof(struct smb2_transform_hdr) ||
+	    buf_data_size < sizeof(struct smb2_hdr)) {
 		pr_err("Transform message is too small (%u)\n",
 		       pdu_length);
 		return -ECONNABORTED;
-- 
2.40.1

[PATCH AUTOSEL 6.1 10/47] ksmbd: validate session id and tree id in compound request

[Sasha Levin]

From: Namjae Jeon <linkinjeon@kernel.org>

[ Upstream commit 3df0411e132ee74a87aa13142dfd2b190275332e ]

`smb2_get_msg()` in smb2_get_ksmbd_tcon() and smb2_check_user_session()
will always return the first request smb2 header in a compound request.
if `SMB2_TREE_CONNECT_HE` is the first command in compound request, will
return 0, i.e. The tree id check is skipped.
This patch use ksmbd_req_buf_next() to get current command in compound.

Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-21506
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 fs/smb/server/smb2pdu.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/fs/smb/server/smb2pdu.c b/fs/smb/server/smb2pdu.c
index c33249393ef36..d2873dc4322d7 100644
--- a/fs/smb/server/smb2pdu.c
+++ b/fs/smb/server/smb2pdu.c
@@ -86,9 +86,9 @@ struct channel *lookup_chann_list(struct ksmbd_session *sess, struct ksmbd_conn
  */
 int smb2_get_ksmbd_tcon(struct ksmbd_work *work)
 {
-	struct smb2_hdr *req_hdr = smb2_get_msg(work->request_buf);
+	struct smb2_hdr *req_hdr = ksmbd_req_buf_next(work);
 	unsigned int cmd = le16_to_cpu(req_hdr->Command);
-	int tree_id;
+	unsigned int tree_id;
 
 	if (cmd == SMB2_TREE_CONNECT_HE ||
 	    cmd ==  SMB2_CANCEL_HE ||
@@ -113,7 +113,7 @@ int smb2_get_ksmbd_tcon(struct ksmbd_work *work)
 			pr_err("The first operation in the compound does not have tcon\n");
 			return -EINVAL;
 		}
-		if (work->tcon->id != tree_id) {
+		if (tree_id != UINT_MAX && work->tcon->id != tree_id) {
 			pr_err("tree id(%u) is different with id(%u) in first operation\n",
 					tree_id, work->tcon->id);
 			return -EINVAL;
@@ -565,9 +565,9 @@ int smb2_allocate_rsp_buf(struct ksmbd_work *work)
  */
 int smb2_check_user_session(struct ksmbd_work *work)
 {
-	struct smb2_hdr *req_hdr = smb2_get_msg(work->request_buf);
+	struct smb2_hdr *req_hdr = ksmbd_req_buf_next(work);
 	struct ksmbd_conn *conn = work->conn;
-	unsigned int cmd = conn->ops->get_cmd_val(work);
+	unsigned int cmd = le16_to_cpu(req_hdr->Command);
 	unsigned long long sess_id;
 
 	/*
@@ -593,7 +593,7 @@ int smb2_check_user_session(struct ksmbd_work *work)
 			pr_err("The first operation in the compound does not have sess\n");
 			return -EINVAL;
 		}
-		if (work->sess->id != sess_id) {
+		if (sess_id != ULLONG_MAX && work->sess->id != sess_id) {
 			pr_err("session id(%llu) is different with the first operation(%lld)\n",
 					sess_id, work->sess->id);
 			return -EINVAL;
-- 
2.40.1

[PATCH AUTOSEL 6.1 11/47] ksmbd: no response from compound read

[Sasha Levin]

From: Namjae Jeon <linkinjeon@kernel.org>

[ Upstream commit e202a1e8634b186da38cbbff85382ea2b9e297cf ]

ksmbd doesn't support compound read. If client send read-read in
compound to ksmbd, there can be memory leak from read buffer.
Windows and linux clients doesn't send it to server yet. For now,
No response from compound read. compound read will be supported soon.

Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-21587, ZDI-CAN-21588
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 fs/smb/server/smb2pdu.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/fs/smb/server/smb2pdu.c b/fs/smb/server/smb2pdu.c
index d2873dc4322d7..29212c1a0eed3 100644
--- a/fs/smb/server/smb2pdu.c
+++ b/fs/smb/server/smb2pdu.c
@@ -6307,6 +6307,11 @@ int smb2_read(struct ksmbd_work *work)
 	unsigned int max_read_size = conn->vals->max_read_size;
 
 	WORK_BUFFERS(work, req, rsp);
+	if (work->next_smb2_rcv_hdr_off) {
+		work->send_no_response = 1;
+		err = -EOPNOTSUPP;
+		goto out;
+	}
 
 	if (test_share_config_flag(work->tcon->share_conf,
 				   KSMBD_SHARE_FLAG_PIPE)) {
-- 
2.40.1

[PATCH AUTOSEL 6.1 12/47] ksmbd: fix out of bounds in init_smb2_rsp_hdr()

[Sasha Levin]

From: Namjae Jeon <linkinjeon@kernel.org>

[ Upstream commit 536bb492d39bb6c080c92f31e8a55fe9934f452b ]

If client send smb2 negotiate request and then send smb1 negotiate
request, init_smb2_rsp_hdr is called for smb1 negotiate request since
need_neg is set to false. This patch ignore smb1 packets after ->need_neg
is set to false.

Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-21541
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 fs/smb/server/server.c     |  7 ++++++-
 fs/smb/server/smb_common.c | 19 +++++++++++--------
 fs/smb/server/smb_common.h |  2 +-
 3 files changed, 18 insertions(+), 10 deletions(-)

diff --git a/fs/smb/server/server.c b/fs/smb/server/server.c
index 847ee62afb8a1..9804cabe72a84 100644
--- a/fs/smb/server/server.c
+++ b/fs/smb/server/server.c
@@ -286,6 +286,7 @@ static void handle_ksmbd_work(struct work_struct *wk)
 static int queue_ksmbd_work(struct ksmbd_conn *conn)
 {
 	struct ksmbd_work *work;
+	int err;
 
 	work = ksmbd_alloc_work_struct();
 	if (!work) {
@@ -297,7 +298,11 @@ static int queue_ksmbd_work(struct ksmbd_conn *conn)
 	work->request_buf = conn->request_buf;
 	conn->request_buf = NULL;
 
-	ksmbd_init_smb_server(work);
+	err = ksmbd_init_smb_server(work);
+	if (err) {
+		ksmbd_free_work_struct(work);
+		return 0;
+	}
 
 	ksmbd_conn_enqueue_request(work);
 	atomic_inc(&conn->r_count);
diff --git a/fs/smb/server/smb_common.c b/fs/smb/server/smb_common.c
index d937e2f45c829..a4421d9458d90 100644
--- a/fs/smb/server/smb_common.c
+++ b/fs/smb/server/smb_common.c
@@ -388,26 +388,29 @@ static struct smb_version_cmds smb1_server_cmds[1] = {
 	[SMB_COM_NEGOTIATE_EX]	= { .proc = smb1_negotiate, },
 };
 
-static void init_smb1_server(struct ksmbd_conn *conn)
+static int init_smb1_server(struct ksmbd_conn *conn)
 {
 	conn->ops = &smb1_server_ops;
 	conn->cmds = smb1_server_cmds;
 	conn->max_cmds = ARRAY_SIZE(smb1_server_cmds);
+	return 0;
 }
 
-void ksmbd_init_smb_server(struct ksmbd_work *work)
+int ksmbd_init_smb_server(struct ksmbd_work *work)
 {
 	struct ksmbd_conn *conn = work->conn;
 	__le32 proto;
 
-	if (conn->need_neg == false)
-		return;
-
 	proto = *(__le32 *)((struct smb_hdr *)work->request_buf)->Protocol;
+	if (conn->need_neg == false) {
+		if (proto == SMB1_PROTO_NUMBER)
+			return -EINVAL;
+		return 0;
+	}
+
 	if (proto == SMB1_PROTO_NUMBER)
-		init_smb1_server(conn);
-	else
-		init_smb3_11_server(conn);
+		return init_smb1_server(conn);
+	return init_smb3_11_server(conn);
 }
 
 int ksmbd_populate_dot_dotdot_entries(struct ksmbd_work *work, int info_level,
diff --git a/fs/smb/server/smb_common.h b/fs/smb/server/smb_common.h
index e63d2a4f466b5..1cbb492cdefec 100644
--- a/fs/smb/server/smb_common.h
+++ b/fs/smb/server/smb_common.h
@@ -427,7 +427,7 @@ bool ksmbd_smb_request(struct ksmbd_conn *conn);
 
 int ksmbd_lookup_dialect_by_id(__le16 *cli_dialects, __le16 dialects_count);
 
-void ksmbd_init_smb_server(struct ksmbd_work *work);
+int ksmbd_init_smb_server(struct ksmbd_work *work);
 
 struct ksmbd_kstat;
 int ksmbd_populate_dot_dotdot_entries(struct ksmbd_work *work,
-- 
2.40.1

[PATCH AUTOSEL 6.1 13/47] ASoC: da7219: Flush pending AAD IRQ when suspending

[Sasha Levin]

From: Dmytro Maluka <dmy@semihalf.com>

[ Upstream commit 91e292917dad64ab8d1d5ca2ab3069ad9dac6f72 ]

da7219_aad_suspend() disables jack detection, which should prevent
generating new interrupts by DA7219 while suspended. However, there is a
theoretical possibility that there is a pending interrupt generated just
before suspending DA7219 and not handled yet, so the IRQ handler may
still run after DA7219 is suspended. To prevent that, wait until the
pending IRQ handling is done.

This patch arose as an attempt to fix the following I2C failure
occurring sometimes during system suspend or resume:

[  355.876211] i2c_designware i2c_designware.3: Transfer while suspended
[  355.876245] WARNING: CPU: 2 PID: 3576 at drivers/i2c/busses/i2c-designware-master.c:570 i2c_dw_xfer+0x411/0x440
...
[  355.876462] Call Trace:
[  355.876468]  <TASK>
[  355.876475]  ? update_load_avg+0x1b3/0x615
[  355.876484]  __i2c_transfer+0x101/0x1d8
[  355.876494]  i2c_transfer+0x74/0x10d
[  355.876504]  regmap_i2c_read+0x6a/0x9c
[  355.876513]  _regmap_raw_read+0x179/0x223
[  355.876521]  regmap_raw_read+0x1e1/0x28e
[  355.876527]  regmap_bulk_read+0x17d/0x1ba
[  355.876532]  ? __wake_up+0xed/0x1bb
[  355.876542]  da7219_aad_irq_thread+0x54/0x2c9 [snd_soc_da7219 5fb8ebb2179cf2fea29af090f3145d68ed8e2184]
[  355.876556]  irq_thread+0x13c/0x231
[  355.876563]  ? irq_forced_thread_fn+0x5f/0x5f
[  355.876570]  ? irq_thread_fn+0x4d/0x4d
[  355.876576]  kthread+0x13a/0x152
[  355.876581]  ? synchronize_irq+0xc3/0xc3
[  355.876587]  ? kthread_blkcg+0x31/0x31
[  355.876592]  ret_from_fork+0x1f/0x30
[  355.876601]  </TASK>

which indicates that the AAD IRQ handler is unexpectedly running when
DA7219 is suspended, and as a result, is trying to read data from DA7219
over I2C and is hitting the I2C driver "Transfer while suspended"
failure.

However, with this patch the above failure is still reproducible. So
this patch does not fix any real observed issue so far, but at least is
useful for confirming that the above issue is not caused by a pending
IRQ but rather looks like a DA7219 hardware issue with an IRQ
unexpectedly generated after jack detection is already disabled.

Signed-off-by: Dmytro Maluka <dmy@semihalf.com>
Link: https://lore.kernel.org/r/20230717193737.161784-2-dmy@semihalf.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/codecs/da7219-aad.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/sound/soc/codecs/da7219-aad.c b/sound/soc/codecs/da7219-aad.c
index bba73c44c219f..49b1622e7bada 100644
--- a/sound/soc/codecs/da7219-aad.c
+++ b/sound/soc/codecs/da7219-aad.c
@@ -863,6 +863,8 @@ void da7219_aad_suspend(struct snd_soc_component *component)
 			}
 		}
 	}
+
+	synchronize_irq(da7219_aad->irq);
 }
 
 void da7219_aad_resume(struct snd_soc_component *component)
-- 
2.40.1

[PATCH AUTOSEL 6.1 14/47] ASoC: da7219: Check for failure reading AAD IRQ events

[Sasha Levin]

From: Dmytro Maluka <dmy@semihalf.com>

[ Upstream commit f0691dc16206f21b13c464434366e2cd632b8ed7 ]

When handling an AAD interrupt, if IRQ events read failed (for example,
due to i2c "Transfer while suspended" failure, i.e. when attempting to
read it while DA7219 is suspended, which may happen due to a spurious
AAD interrupt), the events array contains garbage uninitialized values.
So instead of trying to interprete those values and doing any actions
based on them (potentially resulting in misbehavior, e.g. reporting
bogus events), refuse to handle the interrupt.

Signed-off-by: Dmytro Maluka <dmy@semihalf.com>
Link: https://lore.kernel.org/r/20230717193737.161784-3-dmy@semihalf.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/codecs/da7219-aad.c | 10 +++++++---
 1 file changed, 7 insertions(+), 3 deletions(-)

diff --git a/sound/soc/codecs/da7219-aad.c b/sound/soc/codecs/da7219-aad.c
index 49b1622e7bada..9251490548e8c 100644
--- a/sound/soc/codecs/da7219-aad.c
+++ b/sound/soc/codecs/da7219-aad.c
@@ -353,11 +353,15 @@ static irqreturn_t da7219_aad_irq_thread(int irq, void *data)
 	struct da7219_priv *da7219 = snd_soc_component_get_drvdata(component);
 	u8 events[DA7219_AAD_IRQ_REG_MAX];
 	u8 statusa;
-	int i, report = 0, mask = 0;
+	int i, ret, report = 0, mask = 0;
 
 	/* Read current IRQ events */
-	regmap_bulk_read(da7219->regmap, DA7219_ACCDET_IRQ_EVENT_A,
-			 events, DA7219_AAD_IRQ_REG_MAX);
+	ret = regmap_bulk_read(da7219->regmap, DA7219_ACCDET_IRQ_EVENT_A,
+			       events, DA7219_AAD_IRQ_REG_MAX);
+	if (ret) {
+		dev_warn_ratelimited(component->dev, "Failed to read IRQ events: %d\n", ret);
+		return IRQ_NONE;
+	}
 
 	if (!events[DA7219_AAD_IRQ_REG_A] && !events[DA7219_AAD_IRQ_REG_B])
 		return IRQ_NONE;
-- 
2.40.1

[PATCH AUTOSEL 6.1 15/47] ASoC: nau8821: Add DMI quirk mechanism for active-high jack-detect

[Sasha Levin]

From: Edson Juliano Drosdeck <edson.drosdeck@gmail.com>

[ Upstream commit 1bc40efdaf4a0ccfdb10a1c8e4b458f4764e8e5f ]

Add a quirk mechanism to allow specifying that active-high jack-detection
should be used on platforms where this info is not available in devicetree.

And add an entry for the Positivo CW14Q01P-V2 to the DMI table, so that
jack-detection will work properly on this laptop.

Signed-off-by: Edson Juliano Drosdeck <edson.drosdeck@gmail.com>
Link: https://lore.kernel.org/r/20230719200241.4865-1-edson.drosdeck@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/codecs/nau8821.c | 41 ++++++++++++++++++++++++++++++++++++++
 1 file changed, 41 insertions(+)

diff --git a/sound/soc/codecs/nau8821.c b/sound/soc/codecs/nau8821.c
index 4a72b94e84104..efd92656a060d 100644
--- a/sound/soc/codecs/nau8821.c
+++ b/sound/soc/codecs/nau8821.c
@@ -10,6 +10,7 @@
 #include <linux/acpi.h>
 #include <linux/clk.h>
 #include <linux/delay.h>
+#include <linux/dmi.h>
 #include <linux/init.h>
 #include <linux/i2c.h>
 #include <linux/module.h>
@@ -25,6 +26,13 @@
 #include <sound/tlv.h>
 #include "nau8821.h"
 
+#define NAU8821_JD_ACTIVE_HIGH			BIT(0)
+
+static int nau8821_quirk;
+static int quirk_override = -1;
+module_param_named(quirk, quirk_override, uint, 0444);
+MODULE_PARM_DESC(quirk, "Board-specific quirk override");
+
 #define NAU_FREF_MAX 13500000
 #define NAU_FVCO_MAX 100000000
 #define NAU_FVCO_MIN 90000000
@@ -1696,6 +1704,33 @@ static int nau8821_setup_irq(struct nau8821 *nau8821)
 	return 0;
 }
 
+/* Please keep this list alphabetically sorted */
+static const struct dmi_system_id nau8821_quirk_table[] = {
+	{
+		/* Positivo CW14Q01P-V2 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Positivo Tecnologia SA"),
+			DMI_MATCH(DMI_BOARD_NAME, "CW14Q01P-V2"),
+		},
+		.driver_data = (void *)(NAU8821_JD_ACTIVE_HIGH),
+	},
+	{}
+};
+
+static void nau8821_check_quirks(void)
+{
+	const struct dmi_system_id *dmi_id;
+
+	if (quirk_override != -1) {
+		nau8821_quirk = quirk_override;
+		return;
+	}
+
+	dmi_id = dmi_first_match(nau8821_quirk_table);
+	if (dmi_id)
+		nau8821_quirk = (unsigned long)dmi_id->driver_data;
+}
+
 static int nau8821_i2c_probe(struct i2c_client *i2c)
 {
 	struct device *dev = &i2c->dev;
@@ -1716,6 +1751,12 @@ static int nau8821_i2c_probe(struct i2c_client *i2c)
 
 	nau8821->dev = dev;
 	nau8821->irq = i2c->irq;
+
+	nau8821_check_quirks();
+
+	if (nau8821_quirk & NAU8821_JD_ACTIVE_HIGH)
+		nau8821->jkdet_polarity = 0;
+
 	nau8821_print_device_properties(nau8821);
 
 	nau8821_reset_chip(nau8821->regmap);
-- 
2.40.1

[PATCH AUTOSEL 6.1 16/47] thermal: core: constify params in thermal_zone_device_register

[Sasha Levin]

From: Ahmad Fatoum <a.fatoum@pengutronix.de>

[ Upstream commit 80ddce5f2dbd0e83eadc9f9d373439180d599fe5 ]

Since commit 3d439b1a2ad3 ("thermal/core: Alloc-copy-free the thermal zone
parameters structure"), thermal_zone_device_register() allocates a copy
of the tzp argument and callers need not explicitly manage its lifetime.

This means the function no longer cares about the parameter being
mutable, so constify it.

No functional change.

Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/thermal/thermal_core.c | 4 ++--
 include/linux/thermal.h        | 6 +++---
 2 files changed, 5 insertions(+), 5 deletions(-)

diff --git a/drivers/thermal/thermal_core.c b/drivers/thermal/thermal_core.c
index 1eae4ec719a8f..2d5085488733e 100644
--- a/drivers/thermal/thermal_core.c
+++ b/drivers/thermal/thermal_core.c
@@ -1178,7 +1178,7 @@ static void thermal_set_delay_jiffies(unsigned long *delay_jiffies, int delay_ms
 struct thermal_zone_device *
 thermal_zone_device_register_with_trips(const char *type, struct thermal_trip *trips, int num_trips, int mask,
 					void *devdata, struct thermal_zone_device_ops *ops,
-					struct thermal_zone_params *tzp, int passive_delay,
+					const struct thermal_zone_params *tzp, int passive_delay,
 					int polling_delay)
 {
 	struct thermal_zone_device *tz;
@@ -1335,7 +1335,7 @@ EXPORT_SYMBOL_GPL(thermal_zone_device_register_with_trips);
 
 struct thermal_zone_device *thermal_zone_device_register(const char *type, int ntrips, int mask,
 							 void *devdata, struct thermal_zone_device_ops *ops,
-							 struct thermal_zone_params *tzp, int passive_delay,
+							 const struct thermal_zone_params *tzp, int passive_delay,
 							 int polling_delay)
 {
 	return thermal_zone_device_register_with_trips(type, NULL, ntrips, mask,
diff --git a/include/linux/thermal.h b/include/linux/thermal.h
index 5e093602e8fcd..a339d3af9f9f4 100644
--- a/include/linux/thermal.h
+++ b/include/linux/thermal.h
@@ -337,14 +337,14 @@ static inline void devm_thermal_of_zone_unregister(struct device *dev,
 #ifdef CONFIG_THERMAL
 struct thermal_zone_device *thermal_zone_device_register(const char *, int, int,
 		void *, struct thermal_zone_device_ops *,
-		struct thermal_zone_params *, int, int);
+		const struct thermal_zone_params *, int, int);
 
 void thermal_zone_device_unregister(struct thermal_zone_device *);
 
 struct thermal_zone_device *
 thermal_zone_device_register_with_trips(const char *, struct thermal_trip *, int, int,
 					void *, struct thermal_zone_device_ops *,
-					struct thermal_zone_params *, int, int);
+					const struct thermal_zone_params *, int, int);
 
 int thermal_zone_bind_cooling_device(struct thermal_zone_device *, int,
 				     struct thermal_cooling_device *,
@@ -378,7 +378,7 @@ void thermal_zone_device_critical(struct thermal_zone_device *tz);
 static inline struct thermal_zone_device *thermal_zone_device_register(
 	const char *type, int trips, int mask, void *devdata,
 	struct thermal_zone_device_ops *ops,
-	struct thermal_zone_params *tzp,
+	const struct thermal_zone_params *tzp,
 	int passive_delay, int polling_delay)
 { return ERR_PTR(-ENODEV); }
 static inline void thermal_zone_device_unregister(
-- 
2.40.1

[PATCH AUTOSEL 6.1 17/47] ethernet: atheros: fix return value check in atl1c_tso_csum()

[Sasha Levin]

From: Yuanjun Gong <ruc_gongyuanjun@163.com>

[ Upstream commit 8d01da0a1db237c44c92859ce3612df7af8d3a53 ]

in atl1c_tso_csum, it should check the return value of pskb_trim(),
and return an error code if an unexpected value is returned
by pskb_trim().

Signed-off-by: Yuanjun Gong <ruc_gongyuanjun@163.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/atheros/atl1c/atl1c_main.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/atheros/atl1c/atl1c_main.c b/drivers/net/ethernet/atheros/atl1c/atl1c_main.c
index 40c781695d581..7762e532c6a4f 100644
--- a/drivers/net/ethernet/atheros/atl1c/atl1c_main.c
+++ b/drivers/net/ethernet/atheros/atl1c/atl1c_main.c
@@ -2104,8 +2104,11 @@ static int atl1c_tso_csum(struct atl1c_adapter *adapter,
 			real_len = (((unsigned char *)ip_hdr(skb) - skb->data)
 					+ ntohs(ip_hdr(skb)->tot_len));
 
-			if (real_len < skb->len)
-				pskb_trim(skb, real_len);
+			if (real_len < skb->len) {
+				err = pskb_trim(skb, real_len);
+				if (err)
+					return err;
+			}
 
 			hdr_len = skb_tcp_all_headers(skb);
 			if (unlikely(skb->len == hdr_len)) {
-- 
2.40.1

[PATCH AUTOSEL 6.1 18/47] vxlan: generalize vxlan_parse_gpe_hdr and remove unused args

[Sasha Levin]

From: Jiri Benc <jbenc@redhat.com>

[ Upstream commit 17a0a64448b568442a101de09575f81ffdc45d15 ]

The vxlan_parse_gpe_hdr function extracts the next protocol value from
the GPE header and marks GPE bits as parsed.

In order to be used in the next patch, split the function into protocol
extraction and bit marking. The bit marking is meaningful only in
vxlan_rcv; move it directly there.

Rename the function to vxlan_parse_gpe_proto to reflect what it now
does. Remove unused arguments skb and vxflags. Move the function earlier
in the file to allow it to be called from more places in the next patch.

Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/vxlan/vxlan_core.c | 58 ++++++++++++++++------------------
 1 file changed, 28 insertions(+), 30 deletions(-)

diff --git a/drivers/net/vxlan/vxlan_core.c b/drivers/net/vxlan/vxlan_core.c
index d4be39b19a6be..92635b4541289 100644
--- a/drivers/net/vxlan/vxlan_core.c
+++ b/drivers/net/vxlan/vxlan_core.c
@@ -670,6 +670,32 @@ static int vxlan_fdb_append(struct vxlan_fdb *f,
 	return 1;
 }
 
+static bool vxlan_parse_gpe_proto(struct vxlanhdr *hdr, __be16 *protocol)
+{
+	struct vxlanhdr_gpe *gpe = (struct vxlanhdr_gpe *)hdr;
+
+	/* Need to have Next Protocol set for interfaces in GPE mode. */
+	if (!gpe->np_applied)
+		return false;
+	/* "The initial version is 0. If a receiver does not support the
+	 * version indicated it MUST drop the packet.
+	 */
+	if (gpe->version != 0)
+		return false;
+	/* "When the O bit is set to 1, the packet is an OAM packet and OAM
+	 * processing MUST occur." However, we don't implement OAM
+	 * processing, thus drop the packet.
+	 */
+	if (gpe->oam_flag)
+		return false;
+
+	*protocol = tun_p_to_eth_p(gpe->next_protocol);
+	if (!*protocol)
+		return false;
+
+	return true;
+}
+
 static struct vxlanhdr *vxlan_gro_remcsum(struct sk_buff *skb,
 					  unsigned int off,
 					  struct vxlanhdr *vh, size_t hdrlen,
@@ -1572,35 +1598,6 @@ static void vxlan_parse_gbp_hdr(struct vxlanhdr *unparsed,
 	unparsed->vx_flags &= ~VXLAN_GBP_USED_BITS;
 }
 
-static bool vxlan_parse_gpe_hdr(struct vxlanhdr *unparsed,
-				__be16 *protocol,
-				struct sk_buff *skb, u32 vxflags)
-{
-	struct vxlanhdr_gpe *gpe = (struct vxlanhdr_gpe *)unparsed;
-
-	/* Need to have Next Protocol set for interfaces in GPE mode. */
-	if (!gpe->np_applied)
-		return false;
-	/* "The initial version is 0. If a receiver does not support the
-	 * version indicated it MUST drop the packet.
-	 */
-	if (gpe->version != 0)
-		return false;
-	/* "When the O bit is set to 1, the packet is an OAM packet and OAM
-	 * processing MUST occur." However, we don't implement OAM
-	 * processing, thus drop the packet.
-	 */
-	if (gpe->oam_flag)
-		return false;
-
-	*protocol = tun_p_to_eth_p(gpe->next_protocol);
-	if (!*protocol)
-		return false;
-
-	unparsed->vx_flags &= ~VXLAN_GPE_USED_BITS;
-	return true;
-}
-
 static bool vxlan_set_mac(struct vxlan_dev *vxlan,
 			  struct vxlan_sock *vs,
 			  struct sk_buff *skb, __be32 vni)
@@ -1702,8 +1699,9 @@ static int vxlan_rcv(struct sock *sk, struct sk_buff *skb)
 	 * used by VXLAN extensions if explicitly requested.
 	 */
 	if (vs->flags & VXLAN_F_GPE) {
-		if (!vxlan_parse_gpe_hdr(&unparsed, &protocol, skb, vs->flags))
+		if (!vxlan_parse_gpe_proto(&unparsed, &protocol))
 			goto drop;
+		unparsed.vx_flags &= ~VXLAN_GPE_USED_BITS;
 		raw_proto = true;
 	}
 
-- 
2.40.1

[PATCH AUTOSEL 6.1 19/47] m68k: Fix invalid .section syntax

[Sasha Levin]

From: Ben Hutchings <benh@debian.org>

[ Upstream commit 922a9bd138101e3e5718f0f4d40dba68ef89bb43 ]

gas supports several different forms for .section for ELF targets,
including:
    .section NAME [, "FLAGS"[, @TYPE[,FLAG_SPECIFIC_ARGUMENTS]]]
and:
    .section "NAME"[, #FLAGS...]

In several places we use a mix of these two forms:
    .section NAME, #FLAGS...

A current development snapshot of binutils (2.40.50.20230611) treats
this mixed syntax as an error.

Change to consistently use:
    .section NAME, "FLAGS"
as is used elsewhere in the kernel.

Link: https://buildd.debian.org/status/fetch.php?pkg=linux&arch=m68k&ver=6.4%7Erc6-1%7Eexp1&stamp=1686907300&raw=1
Signed-off-by: Ben Hutchings <benh@debian.org>
Tested-by: Jan-Benedict Glaw <jbglaw@lug-owl.de>
Link: https://lore.kernel.org/r/ZIyBaueWT9jnTwRC@decadent.org.uk
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/m68k/fpsp040/skeleton.S       | 4 ++--
 arch/m68k/ifpsp060/os.S            | 4 ++--
 arch/m68k/kernel/relocate_kernel.S | 4 ++--
 3 files changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/m68k/fpsp040/skeleton.S b/arch/m68k/fpsp040/skeleton.S
index 439395aa6fb42..081922c72daaa 100644
--- a/arch/m68k/fpsp040/skeleton.S
+++ b/arch/m68k/fpsp040/skeleton.S
@@ -499,13 +499,13 @@ in_ea:
 	dbf	%d0,morein
 	rts
 
-	.section .fixup,#alloc,#execinstr
+	.section .fixup,"ax"
 	.even
 1:
 	jbsr	fpsp040_die
 	jbra	.Lnotkern
 
-	.section __ex_table,#alloc
+	.section __ex_table,"a"
 	.align	4
 
 	.long	in_ea,1b
diff --git a/arch/m68k/ifpsp060/os.S b/arch/m68k/ifpsp060/os.S
index 7a0d6e4280665..89e2ec224ab6c 100644
--- a/arch/m68k/ifpsp060/os.S
+++ b/arch/m68k/ifpsp060/os.S
@@ -379,11 +379,11 @@ _060_real_access:
 
 
 | Execption handling for movs access to illegal memory
-	.section .fixup,#alloc,#execinstr
+	.section .fixup,"ax"
 	.even
 1:	moveq		#-1,%d1
 	rts
-.section __ex_table,#alloc
+.section __ex_table,"a"
 	.align 4
 	.long	dmrbuae,1b
 	.long	dmrwuae,1b
diff --git a/arch/m68k/kernel/relocate_kernel.S b/arch/m68k/kernel/relocate_kernel.S
index ab0f1e7d46535..f7667079e08e9 100644
--- a/arch/m68k/kernel/relocate_kernel.S
+++ b/arch/m68k/kernel/relocate_kernel.S
@@ -26,7 +26,7 @@ ENTRY(relocate_new_kernel)
 	lea %pc@(.Lcopy),%a4
 2:	addl #0x00000000,%a4		/* virt_to_phys() */
 
-	.section ".m68k_fixup","aw"
+	.section .m68k_fixup,"aw"
 	.long M68K_FIXUP_MEMOFFSET, 2b+2
 	.previous
 
@@ -49,7 +49,7 @@ ENTRY(relocate_new_kernel)
 	lea %pc@(.Lcont040),%a4
 5:	addl #0x00000000,%a4		/* virt_to_phys() */
 
-	.section ".m68k_fixup","aw"
+	.section .m68k_fixup,"aw"
 	.long M68K_FIXUP_MEMOFFSET, 5b+2
 	.previous
 
-- 
2.40.1

[PATCH AUTOSEL 6.1 20/47] btrfs: remove BUG_ON()'s in add_new_free_space()

[Sasha Levin]

From: Filipe Manana <fdmanana@suse.com>

[ Upstream commit d8ccbd21918fd7fa6ce3226cffc22c444228e8ad ]

At add_new_free_space() we have these BUG_ON()'s that are there to deal
with any failure to add free space to the in memory free space cache.
Such failures are mostly -ENOMEM that should be very rare. However there's
no need to have these BUG_ON()'s, we can just return any error to the
caller and all callers and their upper call chain are already dealing with
errors.

So just make add_new_free_space() return any errors, while removing the
BUG_ON()'s, and returning the total amount of added free space to an
optional u64 pointer argument.

Reported-by: syzbot+3ba856e07b7127889d8c@syzkaller.appspotmail.com
Link: https://lore.kernel.org/linux-btrfs/000000000000e9cb8305ff4e8327@google.com/
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 fs/btrfs/block-group.c     | 51 +++++++++++++++++++++++++-------------
 fs/btrfs/block-group.h     |  4 +--
 fs/btrfs/free-space-tree.c | 24 ++++++++++++------
 3 files changed, 53 insertions(+), 26 deletions(-)

diff --git a/fs/btrfs/block-group.c b/fs/btrfs/block-group.c
index d93e8735ab1f9..d7aad5e8ee377 100644
--- a/fs/btrfs/block-group.c
+++ b/fs/btrfs/block-group.c
@@ -494,12 +494,16 @@ static void fragment_free_space(struct btrfs_block_group *block_group)
  * used yet since their free space will be released as soon as the transaction
  * commits.
  */
-u64 add_new_free_space(struct btrfs_block_group *block_group, u64 start, u64 end)
+int add_new_free_space(struct btrfs_block_group *block_group, u64 start, u64 end,
+		       u64 *total_added_ret)
 {
 	struct btrfs_fs_info *info = block_group->fs_info;
-	u64 extent_start, extent_end, size, total_added = 0;
+	u64 extent_start, extent_end, size;
 	int ret;
 
+	if (total_added_ret)
+		*total_added_ret = 0;
+
 	while (start < end) {
 		ret = find_first_extent_bit(&info->excluded_extents, start,
 					    &extent_start, &extent_end,
@@ -512,10 +516,12 @@ u64 add_new_free_space(struct btrfs_block_group *block_group, u64 start, u64 end
 			start = extent_end + 1;
 		} else if (extent_start > start && extent_start < end) {
 			size = extent_start - start;
-			total_added += size;
 			ret = btrfs_add_free_space_async_trimmed(block_group,
 								 start, size);
-			BUG_ON(ret); /* -ENOMEM or logic error */
+			if (ret)
+				return ret;
+			if (total_added_ret)
+				*total_added_ret += size;
 			start = extent_end + 1;
 		} else {
 			break;
@@ -524,13 +530,15 @@ u64 add_new_free_space(struct btrfs_block_group *block_group, u64 start, u64 end
 
 	if (start < end) {
 		size = end - start;
-		total_added += size;
 		ret = btrfs_add_free_space_async_trimmed(block_group, start,
 							 size);
-		BUG_ON(ret); /* -ENOMEM or logic error */
+		if (ret)
+			return ret;
+		if (total_added_ret)
+			*total_added_ret += size;
 	}
 
-	return total_added;
+	return 0;
 }
 
 static int load_extent_tree_free(struct btrfs_caching_control *caching_ctl)
@@ -637,8 +645,13 @@ static int load_extent_tree_free(struct btrfs_caching_control *caching_ctl)
 
 		if (key.type == BTRFS_EXTENT_ITEM_KEY ||
 		    key.type == BTRFS_METADATA_ITEM_KEY) {
-			total_found += add_new_free_space(block_group, last,
-							  key.objectid);
+			u64 space_added;
+
+			ret = add_new_free_space(block_group, last, key.objectid,
+						 &space_added);
+			if (ret)
+				goto out;
+			total_found += space_added;
 			if (key.type == BTRFS_METADATA_ITEM_KEY)
 				last = key.objectid +
 					fs_info->nodesize;
@@ -653,11 +666,10 @@ static int load_extent_tree_free(struct btrfs_caching_control *caching_ctl)
 		}
 		path->slots[0]++;
 	}
-	ret = 0;
-
-	total_found += add_new_free_space(block_group, last,
-				block_group->start + block_group->length);
 
+	ret = add_new_free_space(block_group, last,
+				 block_group->start + block_group->length,
+				 NULL);
 out:
 	btrfs_free_path(path);
 	return ret;
@@ -2101,9 +2113,11 @@ static int read_one_block_group(struct btrfs_fs_info *info,
 		btrfs_free_excluded_extents(cache);
 	} else if (cache->used == 0) {
 		cache->cached = BTRFS_CACHE_FINISHED;
-		add_new_free_space(cache, cache->start,
-				   cache->start + cache->length);
+		ret = add_new_free_space(cache, cache->start,
+					 cache->start + cache->length, NULL);
 		btrfs_free_excluded_extents(cache);
+		if (ret)
+			goto error;
 	}
 
 	ret = btrfs_add_block_group_cache(info, cache);
@@ -2529,9 +2543,12 @@ struct btrfs_block_group *btrfs_make_block_group(struct btrfs_trans_handle *tran
 		return ERR_PTR(ret);
 	}
 
-	add_new_free_space(cache, chunk_offset, chunk_offset + size);
-
+	ret = add_new_free_space(cache, chunk_offset, chunk_offset + size, NULL);
 	btrfs_free_excluded_extents(cache);
+	if (ret) {
+		btrfs_put_block_group(cache);
+		return ERR_PTR(ret);
+	}
 
 	/*
 	 * Ensure the corresponding space_info object is created and
diff --git a/fs/btrfs/block-group.h b/fs/btrfs/block-group.h
index 8fb14b99a1d1f..0a3d386823583 100644
--- a/fs/btrfs/block-group.h
+++ b/fs/btrfs/block-group.h
@@ -284,8 +284,8 @@ int btrfs_cache_block_group(struct btrfs_block_group *cache, bool wait);
 void btrfs_put_caching_control(struct btrfs_caching_control *ctl);
 struct btrfs_caching_control *btrfs_get_caching_control(
 		struct btrfs_block_group *cache);
-u64 add_new_free_space(struct btrfs_block_group *block_group,
-		       u64 start, u64 end);
+int add_new_free_space(struct btrfs_block_group *block_group,
+		       u64 start, u64 end, u64 *total_added_ret);
 struct btrfs_trans_handle *btrfs_start_trans_remove_block_group(
 				struct btrfs_fs_info *fs_info,
 				const u64 chunk_offset);
diff --git a/fs/btrfs/free-space-tree.c b/fs/btrfs/free-space-tree.c
index a07450f64abb1..a207db9322264 100644
--- a/fs/btrfs/free-space-tree.c
+++ b/fs/btrfs/free-space-tree.c
@@ -1510,9 +1510,13 @@ static int load_free_space_bitmaps(struct btrfs_caching_control *caching_ctl,
 			if (prev_bit == 0 && bit == 1) {
 				extent_start = offset;
 			} else if (prev_bit == 1 && bit == 0) {
-				total_found += add_new_free_space(block_group,
-								  extent_start,
-								  offset);
+				u64 space_added;
+
+				ret = add_new_free_space(block_group, extent_start,
+							 offset, &space_added);
+				if (ret)
+					goto out;
+				total_found += space_added;
 				if (total_found > CACHING_CTL_WAKE_UP) {
 					total_found = 0;
 					wake_up(&caching_ctl->wait);
@@ -1524,8 +1528,9 @@ static int load_free_space_bitmaps(struct btrfs_caching_control *caching_ctl,
 		}
 	}
 	if (prev_bit == 1) {
-		total_found += add_new_free_space(block_group, extent_start,
-						  end);
+		ret = add_new_free_space(block_group, extent_start, end, NULL);
+		if (ret)
+			goto out;
 		extent_count++;
 	}
 
@@ -1564,6 +1569,8 @@ static int load_free_space_extents(struct btrfs_caching_control *caching_ctl,
 	end = block_group->start + block_group->length;
 
 	while (1) {
+		u64 space_added;
+
 		ret = btrfs_next_item(root, path);
 		if (ret < 0)
 			goto out;
@@ -1578,8 +1585,11 @@ static int load_free_space_extents(struct btrfs_caching_control *caching_ctl,
 		ASSERT(key.type == BTRFS_FREE_SPACE_EXTENT_KEY);
 		ASSERT(key.objectid < end && key.objectid + key.offset <= end);
 
-		total_found += add_new_free_space(block_group, key.objectid,
-						  key.objectid + key.offset);
+		ret = add_new_free_space(block_group, key.objectid,
+					 key.objectid + key.offset, &space_added);
+		if (ret)
+			goto out;
+		total_found += space_added;
 		if (total_found > CACHING_CTL_WAKE_UP) {
 			total_found = 0;
 			wake_up(&caching_ctl->wait);
-- 
2.40.1

[PATCH AUTOSEL 6.1 21/47] s390/dasd: use correct number of retries for ERP requests

[Sasha Levin]

From: Stefan Haberland <sth@linux.ibm.com>

[ Upstream commit acea28a6b74f458defda7417d2217b051ba7d444 ]

If a DASD request fails an error recovery procedure (ERP) request might
be built as a copy of the original request to do error recovery.

The ERP request gets a number of retries assigned.
This number is always 256 no matter what other value might have been set
for the original request. This is not what is expected when a user
specifies a certain amount of retries for the device via sysfs.

Correctly use the number of retries of the original request for ERP
requests.

Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Link: https://lore.kernel.org/r/20230721193647.3889634-3-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/s390/block/dasd_3990_erp.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/s390/block/dasd_3990_erp.c b/drivers/s390/block/dasd_3990_erp.c
index 81d283b3cd3bd..b8fa4eba1fe48 100644
--- a/drivers/s390/block/dasd_3990_erp.c
+++ b/drivers/s390/block/dasd_3990_erp.c
@@ -2441,7 +2441,7 @@ static struct dasd_ccw_req *dasd_3990_erp_add_erp(struct dasd_ccw_req *cqr)
 	erp->block    = cqr->block;
 	erp->magic    = cqr->magic;
 	erp->expires  = cqr->expires;
-	erp->retries  = 256;
+	erp->retries  = device->default_retries;
 	erp->buildclk = get_tod_clock();
 	erp->status = DASD_CQR_FILLED;
 
-- 
2.40.1

[PATCH AUTOSEL 6.1 22/47] s390/dasd: fix hanging device after request requeue

[Sasha Levin]

From: Stefan Haberland <sth@linux.ibm.com>

[ Upstream commit 8a2278ce9c25048d999fe1a3561def75d963f471 ]

The DASD device driver has a function to requeue requests to the
blocklayer.
This function is used in various cases when basic settings for the device
have to be changed like High Performance Ficon related parameters or copy
pair settings.

The functions iterates over the device->ccw_queue and also removes the
requests from the block->ccw_queue.
In case the device is started on an alias device instead of the base
device it might be removed from the block->ccw_queue without having it
canceled properly before. This might lead to a hanging device since the
request is no longer on a queue and can not be handled properly.

Fix by iterating over the block->ccw_queue instead of the
device->ccw_queue. This will take care of all blocklayer related requests
and handle them on all associated DASD devices.

Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Link: https://lore.kernel.org/r/20230721193647.3889634-4-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/s390/block/dasd.c | 125 +++++++++++++++-----------------------
 1 file changed, 48 insertions(+), 77 deletions(-)

diff --git a/drivers/s390/block/dasd.c b/drivers/s390/block/dasd.c
index bce3422d85640..04d9b1d4b1ba9 100644
--- a/drivers/s390/block/dasd.c
+++ b/drivers/s390/block/dasd.c
@@ -2926,41 +2926,32 @@ static void _dasd_wake_block_flush_cb(struct dasd_ccw_req *cqr, void *data)
  * Requeue a request back to the block request queue
  * only works for block requests
  */
-static int _dasd_requeue_request(struct dasd_ccw_req *cqr)
+static void _dasd_requeue_request(struct dasd_ccw_req *cqr)
 {
-	struct dasd_block *block = cqr->block;
 	struct request *req;
 
-	if (!block)
-		return -EINVAL;
 	/*
 	 * If the request is an ERP request there is nothing to requeue.
 	 * This will be done with the remaining original request.
 	 */
 	if (cqr->refers)
-		return 0;
+		return;
 	spin_lock_irq(&cqr->dq->lock);
 	req = (struct request *) cqr->callback_data;
 	blk_mq_requeue_request(req, true);
 	spin_unlock_irq(&cqr->dq->lock);
 
-	return 0;
+	return;
 }
 
-/*
- * Go through all request on the dasd_block request queue, cancel them
- * on the respective dasd_device, and return them to the generic
- * block layer.
- */
-static int dasd_flush_block_queue(struct dasd_block *block)
+static int _dasd_requests_to_flushqueue(struct dasd_block *block,
+					struct list_head *flush_queue)
 {
 	struct dasd_ccw_req *cqr, *n;
-	int rc, i;
-	struct list_head flush_queue;
 	unsigned long flags;
+	int rc, i;
 
-	INIT_LIST_HEAD(&flush_queue);
-	spin_lock_bh(&block->queue_lock);
+	spin_lock_irqsave(&block->queue_lock, flags);
 	rc = 0;
 restart:
 	list_for_each_entry_safe(cqr, n, &block->ccw_queue, blocklist) {
@@ -2975,13 +2966,32 @@ static int dasd_flush_block_queue(struct dasd_block *block)
 		 * is returned from the dasd_device layer.
 		 */
 		cqr->callback = _dasd_wake_block_flush_cb;
-		for (i = 0; cqr != NULL; cqr = cqr->refers, i++)
-			list_move_tail(&cqr->blocklist, &flush_queue);
+		for (i = 0; cqr; cqr = cqr->refers, i++)
+			list_move_tail(&cqr->blocklist, flush_queue);
 		if (i > 1)
 			/* moved more than one request - need to restart */
 			goto restart;
 	}
-	spin_unlock_bh(&block->queue_lock);
+	spin_unlock_irqrestore(&block->queue_lock, flags);
+
+	return rc;
+}
+
+/*
+ * Go through all request on the dasd_block request queue, cancel them
+ * on the respective dasd_device, and return them to the generic
+ * block layer.
+ */
+static int dasd_flush_block_queue(struct dasd_block *block)
+{
+	struct dasd_ccw_req *cqr, *n;
+	struct list_head flush_queue;
+	unsigned long flags;
+	int rc;
+
+	INIT_LIST_HEAD(&flush_queue);
+	rc = _dasd_requests_to_flushqueue(block, &flush_queue);
+
 	/* Now call the callback function of flushed requests */
 restart_cb:
 	list_for_each_entry_safe(cqr, n, &flush_queue, blocklist) {
@@ -3864,75 +3874,36 @@ EXPORT_SYMBOL_GPL(dasd_generic_space_avail);
  */
 int dasd_generic_requeue_all_requests(struct dasd_device *device)
 {
+	struct dasd_block *block = device->block;
 	struct list_head requeue_queue;
 	struct dasd_ccw_req *cqr, *n;
-	struct dasd_ccw_req *refers;
 	int rc;
 
-	INIT_LIST_HEAD(&requeue_queue);
-	spin_lock_irq(get_ccwdev_lock(device->cdev));
-	rc = 0;
-	list_for_each_entry_safe(cqr, n, &device->ccw_queue, devlist) {
-		/* Check status and move request to flush_queue */
-		if (cqr->status == DASD_CQR_IN_IO) {
-			rc = device->discipline->term_IO(cqr);
-			if (rc) {
-				/* unable to terminate requeust */
-				dev_err(&device->cdev->dev,
-					"Unable to terminate request %p "
-					"on suspend\n", cqr);
-				spin_unlock_irq(get_ccwdev_lock(device->cdev));
-				dasd_put_device(device);
-				return rc;
-			}
-		}
-		list_move_tail(&cqr->devlist, &requeue_queue);
-	}
-	spin_unlock_irq(get_ccwdev_lock(device->cdev));
-
-	list_for_each_entry_safe(cqr, n, &requeue_queue, devlist) {
-		wait_event(dasd_flush_wq,
-			   (cqr->status != DASD_CQR_CLEAR_PENDING));
+	if (!block)
+		return 0;
 
-		/*
-		 * requeue requests to blocklayer will only work
-		 * for block device requests
-		 */
-		if (_dasd_requeue_request(cqr))
-			continue;
+	INIT_LIST_HEAD(&requeue_queue);
+	rc = _dasd_requests_to_flushqueue(block, &requeue_queue);
 
-		/* remove requests from device and block queue */
-		list_del_init(&cqr->devlist);
-		while (cqr->refers != NULL) {
-			refers = cqr->refers;
-			/* remove the request from the block queue */
-			list_del(&cqr->blocklist);
-			/* free the finished erp request */
-			dasd_free_erp_request(cqr, cqr->memdev);
-			cqr = refers;
+	/* Now call the callback function of flushed requests */
+restart_cb:
+	list_for_each_entry_safe(cqr, n, &requeue_queue, blocklist) {
+		wait_event(dasd_flush_wq, (cqr->status < DASD_CQR_QUEUED));
+		/* Process finished ERP request. */
+		if (cqr->refers) {
+			spin_lock_bh(&block->queue_lock);
+			__dasd_process_erp(block->base, cqr);
+			spin_unlock_bh(&block->queue_lock);
+			/* restart list_for_xx loop since dasd_process_erp
+			 * might remove multiple elements
+			 */
+			goto restart_cb;
 		}
-
-		/*
-		 * _dasd_requeue_request already checked for a valid
-		 * blockdevice, no need to check again
-		 * all erp requests (cqr->refers) have a cqr->block
-		 * pointer copy from the original cqr
-		 */
+		_dasd_requeue_request(cqr);
 		list_del_init(&cqr->blocklist);
 		cqr->block->base->discipline->free_cp(
 			cqr, (struct request *) cqr->callback_data);
 	}
-
-	/*
-	 * if requests remain then they are internal request
-	 * and go back to the device queue
-	 */
-	if (!list_empty(&requeue_queue)) {
-		/* move freeze_queue to start of the ccw_queue */
-		spin_lock_irq(get_ccwdev_lock(device->cdev));
-		list_splice_tail(&requeue_queue, &device->ccw_queue);
-		spin_unlock_irq(get_ccwdev_lock(device->cdev));
-	}
 	dasd_schedule_device_bh(device);
 	return rc;
 }
-- 
2.40.1

[PATCH AUTOSEL 6.1 23/47] fs/nls: make load_nls() take a const parameter

[Sasha Levin]

From: Winston Wen <wentao@uniontech.com>

[ Upstream commit c1ed39ec116272935528ca9b348b8ee79b0791da ]

load_nls() take a char * parameter, use it to find nls module in list or
construct the module name to load it.

This change make load_nls() take a const parameter, so we don't need do
some cast like this:

        ses->local_nls = load_nls((char *)ctx->local_nls->charset);

Suggested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Winston Wen <wentao@uniontech.com>
Reviewed-by: Paulo Alcantara <pc@manguebit.com>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 fs/nls/nls_base.c   | 4 ++--
 include/linux/nls.h | 2 +-
 2 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/fs/nls/nls_base.c b/fs/nls/nls_base.c
index 52ccd34b1e792..a026dbd3593f6 100644
--- a/fs/nls/nls_base.c
+++ b/fs/nls/nls_base.c
@@ -272,7 +272,7 @@ int unregister_nls(struct nls_table * nls)
 	return -EINVAL;
 }
 
-static struct nls_table *find_nls(char *charset)
+static struct nls_table *find_nls(const char *charset)
 {
 	struct nls_table *nls;
 	spin_lock(&nls_lock);
@@ -288,7 +288,7 @@ static struct nls_table *find_nls(char *charset)
 	return nls;
 }
 
-struct nls_table *load_nls(char *charset)
+struct nls_table *load_nls(const char *charset)
 {
 	return try_then_request_module(find_nls(charset), "nls_%s", charset);
 }
diff --git a/include/linux/nls.h b/include/linux/nls.h
index 499e486b3722d..e0bf8367b274a 100644
--- a/include/linux/nls.h
+++ b/include/linux/nls.h
@@ -47,7 +47,7 @@ enum utf16_endian {
 /* nls_base.c */
 extern int __register_nls(struct nls_table *, struct module *);
 extern int unregister_nls(struct nls_table *);
-extern struct nls_table *load_nls(char *);
+extern struct nls_table *load_nls(const char *charset);
 extern void unload_nls(struct nls_table *);
 extern struct nls_table *load_nls_default(void);
 #define register_nls(nls) __register_nls((nls), THIS_MODULE)
-- 
2.40.1

[PATCH AUTOSEL 6.1 24/47] ASoC: rt5682-sdw: fix for JD event handling in ClockStop Mode0

[Sasha Levin]

From: Shuming Fan <shumingf@realtek.com>

[ Upstream commit 02fb23d72720df2b6be3f29fc5787ca018eb92c3 ]

When the system suspends, peripheral Imp-defined interrupt is disabled.
When system level resume is invoked, the peripheral Imp-defined interrupts
should be enabled to handle JD events.

Signed-off-by: Shuming Fan <shumingf@realtek.com>
Reported-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230721090643.128213-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/codecs/rt5682-sdw.c | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)

diff --git a/sound/soc/codecs/rt5682-sdw.c b/sound/soc/codecs/rt5682-sdw.c
index c1a94229dc7e3..868a61c8b0608 100644
--- a/sound/soc/codecs/rt5682-sdw.c
+++ b/sound/soc/codecs/rt5682-sdw.c
@@ -786,8 +786,15 @@ static int __maybe_unused rt5682_dev_resume(struct device *dev)
 	if (!rt5682->first_hw_init)
 		return 0;
 
-	if (!slave->unattach_request)
+	if (!slave->unattach_request) {
+		if (rt5682->disable_irq == true) {
+			mutex_lock(&rt5682->disable_irq_lock);
+			sdw_write_no_pm(slave, SDW_SCP_INTMASK1, SDW_SCP_INT1_IMPL_DEF);
+			rt5682->disable_irq = false;
+			mutex_unlock(&rt5682->disable_irq_lock);
+		}
 		goto regmap_sync;
+	}
 
 	time = wait_for_completion_timeout(&slave->initialization_complete,
 				msecs_to_jiffies(RT5682_PROBE_TIMEOUT));
-- 
2.40.1

[PATCH AUTOSEL 6.1 25/47] ASoc: codecs: ES8316: Fix DMIC config

[Sasha Levin]

From: Edgar <ljijcj@163.com>

[ Upstream commit d20d35d1ad62c6cca36368c1e8f29335a068659e ]

According to the datasheet, the DMIC config should
be changed to { 0, 2 ,3 }

Signed-off-by: Edgar <ljijcj@163.com>
Link: https://lore.kernel.org/r/20230719054722.401954-1-ljijcj@163.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/codecs/es8316.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/sound/soc/codecs/es8316.c b/sound/soc/codecs/es8316.c
index 87775378362e7..c4e4ab93fdb6d 100644
--- a/sound/soc/codecs/es8316.c
+++ b/sound/soc/codecs/es8316.c
@@ -153,7 +153,7 @@ static const char * const es8316_dmic_txt[] = {
 		"dmic data at high level",
 		"dmic data at low level",
 };
-static const unsigned int es8316_dmic_values[] = { 0, 1, 2 };
+static const unsigned int es8316_dmic_values[] = { 0, 2, 3 };
 static const struct soc_enum es8316_dmic_src_enum =
 	SOC_VALUE_ENUM_SINGLE(ES8316_ADC_DMIC, 0, 3,
 			      ARRAY_SIZE(es8316_dmic_txt),
-- 
2.40.1

[PATCH AUTOSEL 6.1 26/47] ASoC: rt711: fix for JD event handling in ClockStop Mode0

[Sasha Levin]

From: Shuming Fan <shumingf@realtek.com>

[ Upstream commit b69de265bd0e877015a00fbba453ef72af162e0f ]

When the system suspends, peripheral Imp-defined interrupt is disabled.
When system level resume is invoked, the peripheral Imp-defined interrupts
should be enabled to handle JD events.

Signed-off-by: Shuming Fan <shumingf@realtek.com>
Reported-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230721090654.128230-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/codecs/rt711-sdw.c | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)

diff --git a/sound/soc/codecs/rt711-sdw.c b/sound/soc/codecs/rt711-sdw.c
index 4fe68bcf2a7c2..9545b8a7eb192 100644
--- a/sound/soc/codecs/rt711-sdw.c
+++ b/sound/soc/codecs/rt711-sdw.c
@@ -541,8 +541,15 @@ static int __maybe_unused rt711_dev_resume(struct device *dev)
 	if (!rt711->first_hw_init)
 		return 0;
 
-	if (!slave->unattach_request)
+	if (!slave->unattach_request) {
+		if (rt711->disable_irq == true) {
+			mutex_lock(&rt711->disable_irq_lock);
+			sdw_write_no_pm(slave, SDW_SCP_INTMASK1, SDW_SCP_INT1_IMPL_DEF);
+			rt711->disable_irq = false;
+			mutex_unlock(&rt711->disable_irq_lock);
+		}
 		goto regmap_sync;
+	}
 
 	time = wait_for_completion_timeout(&slave->initialization_complete,
 				msecs_to_jiffies(RT711_PROBE_TIMEOUT));
-- 
2.40.1

[PATCH AUTOSEL 6.1 27/47] ASoC: rt711-sdca: fix for JD event handling in ClockStop Mode0

[Sasha Levin]

From: Shuming Fan <shumingf@realtek.com>

[ Upstream commit 23adeb7056acd4fd866969f4afb91441776cc4f5 ]

When the system suspends, peripheral SDCA interrupts are disabled.
When system level resume is invoked, the peripheral SDCA interrupts
should be enabled to handle JD events.
Enable SDCA interrupts in resume sequence when ClockStop Mode0 is applied.

Signed-off-by: Shuming Fan <shumingf@realtek.com>
Reported-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230721090711.128247-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/codecs/rt711-sdca-sdw.c | 10 +++++++++-
 1 file changed, 9 insertions(+), 1 deletion(-)

diff --git a/sound/soc/codecs/rt711-sdca-sdw.c b/sound/soc/codecs/rt711-sdca-sdw.c
index e23cec4c457de..487d3010ddc19 100644
--- a/sound/soc/codecs/rt711-sdca-sdw.c
+++ b/sound/soc/codecs/rt711-sdca-sdw.c
@@ -442,8 +442,16 @@ static int __maybe_unused rt711_sdca_dev_resume(struct device *dev)
 	if (!rt711->first_hw_init)
 		return 0;
 
-	if (!slave->unattach_request)
+	if (!slave->unattach_request) {
+		if (rt711->disable_irq == true) {
+			mutex_lock(&rt711->disable_irq_lock);
+			sdw_write_no_pm(slave, SDW_SCP_SDCA_INTMASK1, SDW_SCP_SDCA_INTMASK_SDCA_0);
+			sdw_write_no_pm(slave, SDW_SCP_SDCA_INTMASK2, SDW_SCP_SDCA_INTMASK_SDCA_8);
+			rt711->disable_irq = false;
+			mutex_unlock(&rt711->disable_irq_lock);
+		}
 		goto regmap_sync;
+	}
 
 	time = wait_for_completion_timeout(&slave->initialization_complete,
 				msecs_to_jiffies(RT711_PROBE_TIMEOUT));
-- 
2.40.1

[PATCH AUTOSEL 6.1 28/47] ASoC: atmel: Fix the 8K sample parameter in I2SC master

[Sasha Levin]

From: Guiting Shen <aarongt.shen@gmail.com>

[ Upstream commit f85739c0b2b0d98a32f5ca4fcc5501d2b76df4f6 ]

The 8K sample parameter of 12.288Mhz main system bus clock doesn't work
because the I2SC_MR.IMCKDIV must not be 0 according to the sama5d2
series datasheet(I2SC Mode Register of Register Summary).

So use the 6.144Mhz instead of 12.288Mhz to support 8K sample.

Signed-off-by: Guiting Shen <aarongt.shen@gmail.com>
Link: https://lore.kernel.org/r/20230715030620.62328-1-aarongt.shen@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/soc/atmel/atmel-i2s.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/sound/soc/atmel/atmel-i2s.c b/sound/soc/atmel/atmel-i2s.c
index 425d66edbf867..5e43ff0b537a3 100644
--- a/sound/soc/atmel/atmel-i2s.c
+++ b/sound/soc/atmel/atmel-i2s.c
@@ -163,11 +163,14 @@ struct atmel_i2s_gck_param {
 
 #define I2S_MCK_12M288		12288000UL
 #define I2S_MCK_11M2896		11289600UL
+#define I2S_MCK_6M144		6144000UL
 
 /* mck = (32 * (imckfs+1) / (imckdiv+1)) * fs */
 static const struct atmel_i2s_gck_param gck_params[] = {
+	/* mck = 6.144Mhz */
+	{  8000, I2S_MCK_6M144,  1, 47},	/* mck =  768 fs */
+
 	/* mck = 12.288MHz */
-	{  8000, I2S_MCK_12M288, 0, 47},	/* mck = 1536 fs */
 	{ 16000, I2S_MCK_12M288, 1, 47},	/* mck =  768 fs */
 	{ 24000, I2S_MCK_12M288, 3, 63},	/* mck =  512 fs */
 	{ 32000, I2S_MCK_12M288, 3, 47},	/* mck =  384 fs */
-- 
2.40.1

[PATCH AUTOSEL 6.1 29/47] ALSA: usb-audio: Add quirk for Microsoft Modern Wireless Headset

[Sasha Levin]

From: Takashi Iwai <tiwai@suse.de>

[ Upstream commit 3da435063777f8d861ba5a165344e3f75f839357 ]

Microsoft Modern Wireless Headset (appearing on the host as "Microsoft
USB Link") has a playback and a capture mixer volume/switch, but they
are fairly broken.  The descriptor reports wrong dB ranges for
playback, and the capture volume/switch don't influence on the actual
recording at all.  Moreover, there seem instabilities in the
connection, and at best, we should disable the runtime PM.

So this ended up with a quirk entry for:
- Correct the playback dB range;
  I picked up some reasonable values but it's a guess work
- Disable the capture mixer;
  it's completely useless and confuses PA/PW
- Suppress get-sample-rate, apply the delay for message handling,
  and suppress the auto-suspend

The behavior of the wheel control on the headset is somehow flaky,
too, but it's an issue of HID.

Link: https://bugzilla.suse.com/show_bug.cgi?id=1207129
Link: https://lore.kernel.org/r/20230725092057.15115-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/usb/mixer_maps.c | 14 ++++++++++++++
 sound/usb/quirks.c     |  3 +++
 2 files changed, 17 insertions(+)

diff --git a/sound/usb/mixer_maps.c b/sound/usb/mixer_maps.c
index f4bd1e8ae4b6c..23260aa1919d3 100644
--- a/sound/usb/mixer_maps.c
+++ b/sound/usb/mixer_maps.c
@@ -374,6 +374,15 @@ static const struct usbmix_name_map corsair_virtuoso_map[] = {
 	{ 0 }
 };
 
+/* Microsoft USB Link headset */
+/* a guess work: raw playback volume values are from 2 to 129 */
+static const struct usbmix_dB_map ms_usb_link_dB = { -3225, 0, true };
+static const struct usbmix_name_map ms_usb_link_map[] = {
+	{ 9, NULL, .dB = &ms_usb_link_dB },
+	{ 10, NULL }, /* Headset Capture volume; seems non-working, disabled */
+	{ 0 }   /* terminator */
+};
+
 /* ASUS ROG Zenith II with Realtek ALC1220-VB */
 static const struct usbmix_name_map asus_zenith_ii_map[] = {
 	{ 19, NULL, 12 }, /* FU, Input Gain Pad - broken response, disabled */
@@ -668,6 +677,11 @@ static const struct usbmix_ctl_map usbmix_ctl_maps[] = {
 		.id = USB_ID(0x1395, 0x0025),
 		.map = sennheiser_pc8_map,
 	},
+	{
+		/* Microsoft USB Link headset */
+		.id = USB_ID(0x045e, 0x083c),
+		.map = ms_usb_link_map,
+	},
 	{ 0 } /* terminator */
 };
 
diff --git a/sound/usb/quirks.c b/sound/usb/quirks.c
index 6cf55b7f7a041..d4a7ffef82194 100644
--- a/sound/usb/quirks.c
+++ b/sound/usb/quirks.c
@@ -2011,6 +2011,9 @@ static const struct usb_audio_quirk_flags_table quirk_flags_table[] = {
 		   QUIRK_FLAG_IGNORE_CTL_ERROR),
 	DEVICE_FLG(0x041e, 0x4080, /* Creative Live Cam VF0610 */
 		   QUIRK_FLAG_GET_SAMPLE_RATE),
+	DEVICE_FLG(0x045e, 0x083c, /* MS USB Link headset */
+		   QUIRK_FLAG_GET_SAMPLE_RATE | QUIRK_FLAG_CTL_MSG_DELAY |
+		   QUIRK_FLAG_DISABLE_AUTOSUSPEND),
 	DEVICE_FLG(0x046d, 0x084c, /* Logitech ConferenceCam Connect */
 		   QUIRK_FLAG_GET_SAMPLE_RATE | QUIRK_FLAG_CTL_MSG_DELAY_1M),
 	DEVICE_FLG(0x046d, 0x0991, /* Logitech QuickCam Pro */
-- 
2.40.1

[PATCH AUTOSEL 6.1 30/47] platform/x86/amd/pmf: reduce verbosity of apmf_get_system_params

[Sasha Levin]

From: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>

[ Upstream commit 839e90e75e695b3d9ee17f5a2811e7ee5aea8d4a ]

apmf_get_system_params() failure is not a critical event, reduce its
verbosity from dev_err to dev_dbg.

Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Link: https://lore.kernel.org/r/20230714144435.1239776-1-Shyam-sundar.S-k@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/platform/x86/amd/pmf/acpi.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/platform/x86/amd/pmf/acpi.c b/drivers/platform/x86/amd/pmf/acpi.c
index 081e84e116e79..732b15b392ab9 100644
--- a/drivers/platform/x86/amd/pmf/acpi.c
+++ b/drivers/platform/x86/amd/pmf/acpi.c
@@ -289,7 +289,7 @@ int apmf_acpi_init(struct amd_pmf_dev *pmf_dev)
 
 	ret = apmf_get_system_params(pmf_dev);
 	if (ret) {
-		dev_err(pmf_dev->dev, "APMF apmf_get_system_params failed :%d\n", ret);
+		dev_dbg(pmf_dev->dev, "APMF apmf_get_system_params failed :%d\n", ret);
 		goto out;
 	}
 
-- 
2.40.1

[PATCH AUTOSEL 6.1 31/47] platform/x86/amd/pmf: Notify OS power slider update

[Sasha Levin]

From: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>

[ Upstream commit 33c9ab5b493a0e922b06c12fed4fdcb862212cda ]

APMF fn8 can notify EC about the OS slider position change. Add this
capability to the PMF driver so that it can call the APMF fn8 based on
the changes in the Platform profile events.

Co-developed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Patil Rajesh Reddy <Patil.Reddy@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Link: https://lore.kernel.org/r/20230714144435.1239776-2-Shyam-sundar.S-k@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/platform/x86/amd/pmf/acpi.c | 21 ++++++++
 drivers/platform/x86/amd/pmf/core.c |  9 +++-
 drivers/platform/x86/amd/pmf/pmf.h  | 16 +++++++
 drivers/platform/x86/amd/pmf/sps.c  | 74 +++++++++++++++++++++++++++--
 4 files changed, 114 insertions(+), 6 deletions(-)

diff --git a/drivers/platform/x86/amd/pmf/acpi.c b/drivers/platform/x86/amd/pmf/acpi.c
index 732b15b392ab9..3fc5e4547d9f2 100644
--- a/drivers/platform/x86/amd/pmf/acpi.c
+++ b/drivers/platform/x86/amd/pmf/acpi.c
@@ -106,6 +106,27 @@ int apmf_get_static_slider_granular(struct amd_pmf_dev *pdev,
 									 data, sizeof(*data));
 }
 
+int apmf_os_power_slider_update(struct amd_pmf_dev *pdev, u8 event)
+{
+	struct os_power_slider args;
+	struct acpi_buffer params;
+	union acpi_object *info;
+	int err = 0;
+
+	args.size = sizeof(args);
+	args.slider_event = event;
+
+	params.length = sizeof(args);
+	params.pointer = (void *)&args;
+
+	info = apmf_if_call(pdev, APMF_FUNC_OS_POWER_SLIDER_UPDATE, &params);
+	if (!info)
+		err = -EIO;
+
+	kfree(info);
+	return err;
+}
+
 static void apmf_sbios_heartbeat_notify(struct work_struct *work)
 {
 	struct amd_pmf_dev *dev = container_of(work, struct amd_pmf_dev, heart_beat.work);
diff --git a/drivers/platform/x86/amd/pmf/core.c b/drivers/platform/x86/amd/pmf/core.c
index 73d2357e32f8e..8a38cd94a605d 100644
--- a/drivers/platform/x86/amd/pmf/core.c
+++ b/drivers/platform/x86/amd/pmf/core.c
@@ -71,7 +71,11 @@ static int amd_pmf_pwr_src_notify_call(struct notifier_block *nb, unsigned long
 			return NOTIFY_DONE;
 	}
 
-	amd_pmf_set_sps_power_limits(pmf);
+	if (is_apmf_func_supported(pmf, APMF_FUNC_STATIC_SLIDER_GRANULAR))
+		amd_pmf_set_sps_power_limits(pmf);
+
+	if (is_apmf_func_supported(pmf, APMF_FUNC_OS_POWER_SLIDER_UPDATE))
+		amd_pmf_power_slider_update_event(pmf);
 
 	return NOTIFY_OK;
 }
@@ -295,7 +299,8 @@ static void amd_pmf_init_features(struct amd_pmf_dev *dev)
 	int ret;
 
 	/* Enable Static Slider */
-	if (is_apmf_func_supported(dev, APMF_FUNC_STATIC_SLIDER_GRANULAR)) {
+	if (is_apmf_func_supported(dev, APMF_FUNC_STATIC_SLIDER_GRANULAR) ||
+	    is_apmf_func_supported(dev, APMF_FUNC_OS_POWER_SLIDER_UPDATE)) {
 		amd_pmf_init_sps(dev);
 		dev->pwr_src_notifier.notifier_call = amd_pmf_pwr_src_notify_call;
 		power_supply_reg_notifier(&dev->pwr_src_notifier);
diff --git a/drivers/platform/x86/amd/pmf/pmf.h b/drivers/platform/x86/amd/pmf/pmf.h
index 06c30cdc05733..deba88e6e4c8d 100644
--- a/drivers/platform/x86/amd/pmf/pmf.h
+++ b/drivers/platform/x86/amd/pmf/pmf.h
@@ -21,6 +21,7 @@
 #define APMF_FUNC_SBIOS_HEARTBEAT			4
 #define APMF_FUNC_AUTO_MODE					5
 #define APMF_FUNC_SET_FAN_IDX				7
+#define APMF_FUNC_OS_POWER_SLIDER_UPDATE		8
 #define APMF_FUNC_STATIC_SLIDER_GRANULAR       9
 #define APMF_FUNC_DYN_SLIDER_AC				11
 #define APMF_FUNC_DYN_SLIDER_DC				12
@@ -44,6 +45,14 @@
 #define GET_STT_LIMIT_APU	0x20
 #define GET_STT_LIMIT_HS2	0x21
 
+/* OS slider update notification */
+#define DC_BEST_PERF		0
+#define DC_BETTER_PERF		1
+#define DC_BATTERY_SAVER	3
+#define AC_BEST_PERF		4
+#define AC_BETTER_PERF		5
+#define AC_BETTER_BATTERY	6
+
 /* Fan Index for Auto Mode */
 #define FAN_INDEX_AUTO		0xFFFFFFFF
 
@@ -193,6 +202,11 @@ struct amd_pmf_static_slider_granular {
 	struct apmf_sps_prop_granular prop[POWER_SOURCE_MAX][POWER_MODE_MAX];
 };
 
+struct os_power_slider {
+	u16 size;
+	u8 slider_event;
+} __packed;
+
 struct fan_table_control {
 	bool manual;
 	unsigned long fan_id;
@@ -383,6 +397,7 @@ int amd_pmf_send_cmd(struct amd_pmf_dev *dev, u8 message, bool get, u32 arg, u32
 int amd_pmf_init_metrics_table(struct amd_pmf_dev *dev);
 int amd_pmf_get_power_source(void);
 int apmf_install_handler(struct amd_pmf_dev *pmf_dev);
+int apmf_os_power_slider_update(struct amd_pmf_dev *dev, u8 flag);
 
 /* SPS Layer */
 int amd_pmf_get_pprof_modes(struct amd_pmf_dev *pmf);
@@ -393,6 +408,7 @@ void amd_pmf_deinit_sps(struct amd_pmf_dev *dev);
 int apmf_get_static_slider_granular(struct amd_pmf_dev *pdev,
 				    struct apmf_static_slider_granular_output *output);
 bool is_pprof_balanced(struct amd_pmf_dev *pmf);
+int amd_pmf_power_slider_update_event(struct amd_pmf_dev *dev);
 
 
 int apmf_update_fan_idx(struct amd_pmf_dev *pdev, bool manual, u32 idx);
diff --git a/drivers/platform/x86/amd/pmf/sps.c b/drivers/platform/x86/amd/pmf/sps.c
index bed762d47a14a..fd448844de206 100644
--- a/drivers/platform/x86/amd/pmf/sps.c
+++ b/drivers/platform/x86/amd/pmf/sps.c
@@ -119,14 +119,77 @@ int amd_pmf_get_pprof_modes(struct amd_pmf_dev *pmf)
 	return mode;
 }
 
+int amd_pmf_power_slider_update_event(struct amd_pmf_dev *dev)
+{
+	u8 mode, flag = 0;
+	int src;
+
+	mode = amd_pmf_get_pprof_modes(dev);
+	if (mode < 0)
+		return mode;
+
+	src = amd_pmf_get_power_source();
+
+	if (src == POWER_SOURCE_AC) {
+		switch (mode) {
+		case POWER_MODE_PERFORMANCE:
+			flag |= BIT(AC_BEST_PERF);
+			break;
+		case POWER_MODE_BALANCED_POWER:
+			flag |= BIT(AC_BETTER_PERF);
+			break;
+		case POWER_MODE_POWER_SAVER:
+			flag |= BIT(AC_BETTER_BATTERY);
+			break;
+		default:
+			dev_err(dev->dev, "unsupported platform profile\n");
+			return -EOPNOTSUPP;
+		}
+
+	} else if (src == POWER_SOURCE_DC) {
+		switch (mode) {
+		case POWER_MODE_PERFORMANCE:
+			flag |= BIT(DC_BEST_PERF);
+			break;
+		case POWER_MODE_BALANCED_POWER:
+			flag |= BIT(DC_BETTER_PERF);
+			break;
+		case POWER_MODE_POWER_SAVER:
+			flag |= BIT(DC_BATTERY_SAVER);
+			break;
+		default:
+			dev_err(dev->dev, "unsupported platform profile\n");
+			return -EOPNOTSUPP;
+		}
+	}
+
+	apmf_os_power_slider_update(dev, flag);
+
+	return 0;
+}
+
 static int amd_pmf_profile_set(struct platform_profile_handler *pprof,
 			       enum platform_profile_option profile)
 {
 	struct amd_pmf_dev *pmf = container_of(pprof, struct amd_pmf_dev, pprof);
+	int ret = 0;
 
 	pmf->current_profile = profile;
 
-	return amd_pmf_set_sps_power_limits(pmf);
+	/* Notify EC about the slider position change */
+	if (is_apmf_func_supported(pmf, APMF_FUNC_OS_POWER_SLIDER_UPDATE)) {
+		ret = amd_pmf_power_slider_update_event(pmf);
+		if (ret)
+			return ret;
+	}
+
+	if (is_apmf_func_supported(pmf, APMF_FUNC_STATIC_SLIDER_GRANULAR)) {
+		ret = amd_pmf_set_sps_power_limits(pmf);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
 }
 
 int amd_pmf_init_sps(struct amd_pmf_dev *dev)
@@ -134,10 +197,13 @@ int amd_pmf_init_sps(struct amd_pmf_dev *dev)
 	int err;
 
 	dev->current_profile = PLATFORM_PROFILE_BALANCED;
-	amd_pmf_load_defaults_sps(dev);
 
-	/* update SPS balanced power mode thermals */
-	amd_pmf_set_sps_power_limits(dev);
+	if (is_apmf_func_supported(dev, APMF_FUNC_STATIC_SLIDER_GRANULAR)) {
+		amd_pmf_load_defaults_sps(dev);
+
+		/* update SPS balanced power mode thermals */
+		amd_pmf_set_sps_power_limits(dev);
+	}
 
 	dev->pprof.profile_get = amd_pmf_profile_get;
 	dev->pprof.profile_set = amd_pmf_profile_set;
-- 
2.40.1

[PATCH AUTOSEL 6.1 32/47] platform/x86: intel: hid: Always call BTNL ACPI method

[Sasha Levin]

From: Hans de Goede <hdegoede@redhat.com>

[ Upstream commit e3ab18de2b09361d6f0e4aafb9cfd6d002ce43a1 ]

On a HP Elite Dragonfly G2 the 0xcc and 0xcd events for SW_TABLET_MODE
are only send after the BTNL ACPI method has been called.

Likely more devices need this, so make the BTNL ACPI method unconditional
instead of only doing it on devices with a 5 button array.

Note this also makes the intel_button_array_enable() call in probe()
unconditional, that function does its own priv->array check. This makes
the intel_button_array_enable() call in probe() consistent with the calls
done on suspend/resume which also rely on the priv->array check inside
the function.

Reported-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Closes: https://lore.kernel.org/platform-driver-x86/20230712175023.31651-1-maxtram95@gmail.com/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230715181516.5173-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/platform/x86/intel/hid.c | 21 +++++++++------------
 1 file changed, 9 insertions(+), 12 deletions(-)

diff --git a/drivers/platform/x86/intel/hid.c b/drivers/platform/x86/intel/hid.c
index b6313ecd190c0..df533b277b999 100644
--- a/drivers/platform/x86/intel/hid.c
+++ b/drivers/platform/x86/intel/hid.c
@@ -601,7 +601,7 @@ static bool button_array_present(struct platform_device *device)
 static int intel_hid_probe(struct platform_device *device)
 {
 	acpi_handle handle = ACPI_HANDLE(&device->dev);
-	unsigned long long mode;
+	unsigned long long mode, dummy;
 	struct intel_hid_priv *priv;
 	acpi_status status;
 	int err;
@@ -666,18 +666,15 @@ static int intel_hid_probe(struct platform_device *device)
 	if (err)
 		goto err_remove_notify;
 
-	if (priv->array) {
-		unsigned long long dummy;
+	intel_button_array_enable(&device->dev, true);
 
-		intel_button_array_enable(&device->dev, true);
-
-		/* Call button load method to enable HID power button */
-		if (!intel_hid_evaluate_method(handle, INTEL_HID_DSM_BTNL_FN,
-					       &dummy)) {
-			dev_warn(&device->dev,
-				 "failed to enable HID power button\n");
-		}
-	}
+	/*
+	 * Call button load method to enable HID power button
+	 * Always do this since it activates events on some devices without
+	 * a button array too.
+	 */
+	if (!intel_hid_evaluate_method(handle, INTEL_HID_DSM_BTNL_FN, &dummy))
+		dev_warn(&device->dev, "failed to enable HID power button\n");
 
 	device_init_wakeup(&device->dev, true);
 	/*
-- 
2.40.1

[PATCH AUTOSEL 6.1 33/47] platform/x86/intel/hid: Add HP Dragonfly G2 to VGBS DMI quirks

[Sasha Levin]

From: Maxim Mikityanskiy <maxtram95@gmail.com>

[ Upstream commit 7783e97f8558ad7a4d1748922461bc88483fbcdf ]

HP Elite Dragonfly G2 (a convertible laptop/tablet) has a reliable VGBS
method. If VGBS is not called on boot, the firmware sends an initial
0xcd event shortly after calling the BTNL method, but only if the device
is booted in the laptop mode. However, if the device is booted in the
tablet mode and VGBS is not called, there is no initial 0xcc event, and
the input device for SW_TABLET_MODE is not registered up until the user
turns the device into the laptop mode.

Call VGBS on boot on this device to get the initial state of
SW_TABLET_MODE in a reliable way.

Tested with BIOS 1.13.1.

Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Link: https://lore.kernel.org/r/20230716183213.64173-1-maxtram95@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/platform/x86/intel/hid.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/drivers/platform/x86/intel/hid.c b/drivers/platform/x86/intel/hid.c
index df533b277b999..b96ef0eb82aff 100644
--- a/drivers/platform/x86/intel/hid.c
+++ b/drivers/platform/x86/intel/hid.c
@@ -131,6 +131,12 @@ static const struct dmi_system_id dmi_vgbs_allow_list[] = {
 			DMI_MATCH(DMI_PRODUCT_NAME, "Surface Go"),
 		},
 	},
+	{
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "HP"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "HP Elite Dragonfly G2 Notebook PC"),
+		},
+	},
 	{ }
 };
 
-- 
2.40.1

[PATCH AUTOSEL 6.1 34/47] platform/x86: think-lmi: Use kfree_sensitive instead of kfree

[Sasha Levin]

From: Wang Ming <machel@vivo.com>

[ Upstream commit 1da0893aed2e48e2bdf37c29b029f2e060d25927 ]

key might contain private part of the key, so better use
kfree_sensitive to free it.

Signed-off-by: Wang Ming <machel@vivo.com>
Link: https://lore.kernel.org/r/20230717101114.18966-1-machel@vivo.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/platform/x86/think-lmi.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/platform/x86/think-lmi.c b/drivers/platform/x86/think-lmi.c
index 3cbb92b6c5215..f6290221d139d 100644
--- a/drivers/platform/x86/think-lmi.c
+++ b/drivers/platform/x86/think-lmi.c
@@ -719,12 +719,12 @@ static ssize_t cert_to_password_store(struct kobject *kobj,
 	/* Format: 'Password,Signature' */
 	auth_str = kasprintf(GFP_KERNEL, "%s,%s", passwd, setting->signature);
 	if (!auth_str) {
-		kfree(passwd);
+		kfree_sensitive(passwd);
 		return -ENOMEM;
 	}
 	ret = tlmi_simple_call(LENOVO_CERT_TO_PASSWORD_GUID, auth_str);
 	kfree(auth_str);
-	kfree(passwd);
+	kfree_sensitive(passwd);
 
 	return ret ?: count;
 }
-- 
2.40.1

[PATCH AUTOSEL 6.1 35/47] platform/x86: asus-wmi: Fix setting RGB mode on some TUF laptops

[Sasha Levin]

From: Kristian Angelov <kristiana2000@abv.bg>

[ Upstream commit 6a758a3e831ce1a84c9c209ac6dc755f4c8ce77a ]

This patch fixes setting the cmd values to 0xb3 and 0xb4.
This is necessary on some TUF laptops in order to set the RGB mode.

Closes: https://lore.kernel.org/platform-driver-x86/443078148.491022.1677576298133@nm83.abv.bg
Signed-off-by: Kristian Angelov <kristiana2000@abv.bg>
Reviewed-by: Luke D. Jones <luke@ljones.dev>
Link: https://lore.kernel.org/r/ZLlS7o6UdTUBkyqa@wyvern.localdomain
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/platform/x86/asus-wmi.c | 14 ++++++++++++--
 1 file changed, 12 insertions(+), 2 deletions(-)

diff --git a/drivers/platform/x86/asus-wmi.c b/drivers/platform/x86/asus-wmi.c
index 02bf286924183..36effe04c6f33 100644
--- a/drivers/platform/x86/asus-wmi.c
+++ b/drivers/platform/x86/asus-wmi.c
@@ -738,13 +738,23 @@ static ssize_t kbd_rgb_mode_store(struct device *dev,
 				 struct device_attribute *attr,
 				 const char *buf, size_t count)
 {
-	u32 cmd, mode, r, g,  b,  speed;
+	u32 cmd, mode, r, g, b, speed;
 	int err;
 
 	if (sscanf(buf, "%d %d %d %d %d %d", &cmd, &mode, &r, &g, &b, &speed) != 6)
 		return -EINVAL;
 
-	cmd = !!cmd;
+	/* B3 is set and B4 is save to BIOS */
+	switch (cmd) {
+	case 0:
+		cmd = 0xb3;
+		break;
+	case 1:
+		cmd = 0xb4;
+		break;
+	default:
+		return -EINVAL;
+	}
 
 	/* These are the known usable modes across all TUF/ROG */
 	if (mode >= 12 || mode == 9)
-- 
2.40.1

[PATCH AUTOSEL 6.1 36/47] platform/x86: huawei-wmi: Silence ambient light sensor

[Sasha Levin]

From: Konstantin Shelekhin <k.shelekhin@ftml.net>

[ Upstream commit c21733754cd6ecbca346f2adf9b17d4cfa50504f ]

Currently huawei-wmi causes a lot of spam in dmesg on my
Huawei MateBook X Pro 2022:

  ...
  [36409.328463] input input9: Unknown key pressed, code: 0x02c1
  [36411.335104] input input9: Unknown key pressed, code: 0x02c1
  [36412.338674] input input9: Unknown key pressed, code: 0x02c1
  [36414.848564] input input9: Unknown key pressed, code: 0x02c1
  [36416.858706] input input9: Unknown key pressed, code: 0x02c1
  ...

Fix that by ignoring events generated by ambient light sensor.

This issue was reported on GitHub and resolved with the following merge
request:

  https://github.com/aymanbagabas/Huawei-WMI/pull/70

I've contacted the mainter of this repo and he gave me the "go ahead" to
send this patch to the maling list.

Signed-off-by: Konstantin Shelekhin <k.shelekhin@ftml.net>
Link: https://lore.kernel.org/r/20230722155922.173856-1-k.shelekhin@ftml.net
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/platform/x86/huawei-wmi.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/platform/x86/huawei-wmi.c b/drivers/platform/x86/huawei-wmi.c
index b85050e4a0d65..ae5daecff1771 100644
--- a/drivers/platform/x86/huawei-wmi.c
+++ b/drivers/platform/x86/huawei-wmi.c
@@ -86,6 +86,8 @@ static const struct key_entry huawei_wmi_keymap[] = {
 	{ KE_IGNORE, 0x293, { KEY_KBDILLUMTOGGLE } },
 	{ KE_IGNORE, 0x294, { KEY_KBDILLUMUP } },
 	{ KE_IGNORE, 0x295, { KEY_KBDILLUMUP } },
+	// Ignore Ambient Light Sensoring
+	{ KE_KEY,    0x2c1, { KEY_RESERVED } },
 	{ KE_END,	 0 }
 };
 
-- 
2.40.1

[PATCH AUTOSEL 6.1 37/47] drm/amd/smu: use AverageGfxclkFrequency* to replace previous GFX Curr Clock

[Sasha Levin]

From: Jane Jian <Jane.Jian@amd.com>

[ Upstream commit 4a37c55b859a69f429bfa7fab4fc43ee470b60ed ]

Report current GFX clock also from average clock value as the original
CurrClock data is not valid/accurate any more as per FW team

Signed-off-by: Jane Jian <Jane.Jian@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/gpu/drm/amd/pm/swsmu/smu13/smu_v13_0_0_ppt.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/amd/pm/swsmu/smu13/smu_v13_0_0_ppt.c b/drivers/gpu/drm/amd/pm/swsmu/smu13/smu_v13_0_0_ppt.c
index f7ac488a3da20..503e844baede2 100644
--- a/drivers/gpu/drm/amd/pm/swsmu/smu13/smu_v13_0_0_ppt.c
+++ b/drivers/gpu/drm/amd/pm/swsmu/smu13/smu_v13_0_0_ppt.c
@@ -1305,7 +1305,7 @@ static ssize_t smu_v13_0_0_get_gpu_metrics(struct smu_context *smu,
 	gpu_metrics->average_vclk1_frequency = metrics->AverageVclk1Frequency;
 	gpu_metrics->average_dclk1_frequency = metrics->AverageDclk1Frequency;
 
-	gpu_metrics->current_gfxclk = metrics->CurrClock[PPCLK_GFXCLK];
+	gpu_metrics->current_gfxclk = gpu_metrics->average_gfxclk_frequency;
 	gpu_metrics->current_socclk = metrics->CurrClock[PPCLK_SOCCLK];
 	gpu_metrics->current_uclk = metrics->CurrClock[PPCLK_UCLK];
 	gpu_metrics->current_vclk0 = metrics->CurrClock[PPCLK_VCLK_0];
-- 
2.40.1

[PATCH AUTOSEL 6.1 38/47] drm/amd/display: Guard DCN31 PHYD32CLK logic against chip family

[Sasha Levin]

From: George Shen <george.shen@amd.com>

[ Upstream commit 25b054c3c89cb6a7106a7982f0f70e83d0797dab ]

[Why]
Current yellow carp B0 PHYD32CLK logic is incorrectly applied to other
ASICs.

[How]
Add guard to check chip family is yellow carp before applying logic.

Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/gpu/drm/amd/display/dc/dcn31/dcn31_dccg.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/amd/display/dc/dcn31/dcn31_dccg.c b/drivers/gpu/drm/amd/display/dc/dcn31/dcn31_dccg.c
index 7d2b982506fd7..0cc510e16d9d5 100644
--- a/drivers/gpu/drm/amd/display/dc/dcn31/dcn31_dccg.c
+++ b/drivers/gpu/drm/amd/display/dc/dcn31/dcn31_dccg.c
@@ -76,7 +76,8 @@ static enum phyd32clk_clock_source get_phy_mux_symclk(
 		struct dcn_dccg *dccg_dcn,
 		enum phyd32clk_clock_source src)
 {
-	if (dccg_dcn->base.ctx->asic_id.hw_internal_rev == YELLOW_CARP_B0) {
+	if (dccg_dcn->base.ctx->asic_id.chip_family == FAMILY_YELLOW_CARP &&
+			dccg_dcn->base.ctx->asic_id.hw_internal_rev == YELLOW_CARP_B0) {
 		if (src == PHYD32CLKC)
 			src = PHYD32CLKF;
 		if (src == PHYD32CLKD)
-- 
2.40.1

[PATCH AUTOSEL 6.1 39/47] drm/amd/display: Exit idle optimizations before attempt to access PHY

[Sasha Levin]

From: Leo Chen <sancchen@amd.com>

[ Upstream commit de612738e9771bd66aeb20044486c457c512f684 ]

[Why & How]
DMUB may hang when powering down pixel clocks due to no dprefclk.

It is fixed by exiting idle optimization before the attempt to access PHY.

Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Leo Chen <sancchen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.c b/drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.c
index d260eaa1509ed..9378c98d02cfe 100644
--- a/drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.c
+++ b/drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.c
@@ -1813,10 +1813,13 @@ void dce110_enable_accelerated_mode(struct dc *dc, struct dc_state *context)
 			hws->funcs.edp_backlight_control(edp_link_with_sink, false);
 		}
 		/*resume from S3, no vbios posting, no need to power down again*/
+		clk_mgr_exit_optimized_pwr_state(dc, dc->clk_mgr);
+
 		power_down_all_hw_blocks(dc);
 		disable_vga_and_power_gate_all_controllers(dc);
 		if (edp_link_with_sink && !keep_edp_vdd_on)
 			dc->hwss.edp_power_control(edp_link_with_sink, false);
+		clk_mgr_optimize_pwr_state(dc, dc->clk_mgr);
 	}
 	bios_set_scratch_acc_mode_change(dc->ctx->dc_bios, 1);
 }
-- 
2.40.1

[PATCH AUTOSEL 6.1 40/47] ovl: Always reevaluate the file signature for IMA

[Sasha Levin]

From: Eric Snowberg <eric.snowberg@oracle.com>

[ Upstream commit 18b44bc5a67275641fb26f2c54ba7eef80ac5950 ]

Commit db1d1e8b9867 ("IMA: use vfs_getattr_nosec to get the i_version")
partially closed an IMA integrity issue when directly modifying a file
on the lower filesystem.  If the overlay file is first opened by a user
and later the lower backing file is modified by root, but the extended
attribute is NOT updated, the signature validation succeeds with the old
original signature.

Update the super_block s_iflags to SB_I_IMA_UNVERIFIABLE_SIGNATURE to
force signature reevaluation on every file access until a fine grained
solution can be found.

Signed-off-by: Eric Snowberg <eric.snowberg@oracle.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 fs/overlayfs/super.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/fs/overlayfs/super.c b/fs/overlayfs/super.c
index 51eec4a8e82b2..08d3a1f34ac6c 100644
--- a/fs/overlayfs/super.c
+++ b/fs/overlayfs/super.c
@@ -2155,7 +2155,7 @@ static int ovl_fill_super(struct super_block *sb, void *data, int silent)
 		ovl_trusted_xattr_handlers;
 	sb->s_fs_info = ofs;
 	sb->s_flags |= SB_POSIXACL;
-	sb->s_iflags |= SB_I_SKIP_SYNC;
+	sb->s_iflags |= SB_I_SKIP_SYNC | SB_I_IMA_UNVERIFIABLE_SIGNATURE;
 
 	err = -ENOMEM;
 	root_dentry = ovl_get_root(sb, upperpath.dentry, oe);
-- 
2.40.1

[PATCH AUTOSEL 6.1 41/47] ata: pata_arasan_cf: Use dev_err_probe() instead dev_err() in data_xfer()

[Sasha Levin]

From: Minjie Du <duminjie@vivo.com>

[ Upstream commit 4139f992c49356391fb086c0c8ce51f66c26d623 ]

It is possible for dma_request_chan() to return EPROBE_DEFER, which
means acdev->host->dev is not ready yet. At this point dev_err() will
have no output. Use dev_err_probe() instead.

Signed-off-by: Minjie Du <duminjie@vivo.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/ata/pata_arasan_cf.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/ata/pata_arasan_cf.c b/drivers/ata/pata_arasan_cf.c
index e89617ed9175b..46588fc829432 100644
--- a/drivers/ata/pata_arasan_cf.c
+++ b/drivers/ata/pata_arasan_cf.c
@@ -529,7 +529,8 @@ static void data_xfer(struct work_struct *work)
 	/* dma_request_channel may sleep, so calling from process context */
 	acdev->dma_chan = dma_request_chan(acdev->host->dev, "data");
 	if (IS_ERR(acdev->dma_chan)) {
-		dev_err(acdev->host->dev, "Unable to get dma_chan\n");
+		dev_err_probe(acdev->host->dev, PTR_ERR(acdev->dma_chan),
+			      "Unable to get dma_chan\n");
 		acdev->dma_chan = NULL;
 		goto chan_request_fail;
 	}
-- 
2.40.1

[PATCH AUTOSEL 6.1 42/47] rbd: make get_lock_owner_info() return a single locker or NULL

[Sasha Levin]

From: Ilya Dryomov <idryomov@gmail.com>

[ Upstream commit f38cb9d9c2045dad16eead4a2e1aedfddd94603b ]

Make the "num_lockers can be only 0 or 1" assumption explicit and
simplify the API by getting rid of output parameters in preparation
for calling get_lock_owner_info() twice before blocklisting.

Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Dongsheng Yang <dongsheng.yang@easystack.cn>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/block/rbd.c | 84 +++++++++++++++++++++++++++------------------
 1 file changed, 51 insertions(+), 33 deletions(-)

diff --git a/drivers/block/rbd.c b/drivers/block/rbd.c
index e009f480675d2..523a903d6ae5f 100644
--- a/drivers/block/rbd.c
+++ b/drivers/block/rbd.c
@@ -3850,10 +3850,17 @@ static void wake_lock_waiters(struct rbd_device *rbd_dev, int result)
 	list_splice_tail_init(&rbd_dev->acquiring_list, &rbd_dev->running_list);
 }
 
-static int get_lock_owner_info(struct rbd_device *rbd_dev,
-			       struct ceph_locker **lockers, u32 *num_lockers)
+static void free_locker(struct ceph_locker *locker)
+{
+	if (locker)
+		ceph_free_lockers(locker, 1);
+}
+
+static struct ceph_locker *get_lock_owner_info(struct rbd_device *rbd_dev)
 {
 	struct ceph_osd_client *osdc = &rbd_dev->rbd_client->client->osdc;
+	struct ceph_locker *lockers;
+	u32 num_lockers;
 	u8 lock_type;
 	char *lock_tag;
 	int ret;
@@ -3862,39 +3869,45 @@ static int get_lock_owner_info(struct rbd_device *rbd_dev,
 
 	ret = ceph_cls_lock_info(osdc, &rbd_dev->header_oid,
 				 &rbd_dev->header_oloc, RBD_LOCK_NAME,
-				 &lock_type, &lock_tag, lockers, num_lockers);
-	if (ret)
-		return ret;
+				 &lock_type, &lock_tag, &lockers, &num_lockers);
+	if (ret) {
+		rbd_warn(rbd_dev, "failed to retrieve lockers: %d", ret);
+		return ERR_PTR(ret);
+	}
 
-	if (*num_lockers == 0) {
+	if (num_lockers == 0) {
 		dout("%s rbd_dev %p no lockers detected\n", __func__, rbd_dev);
+		lockers = NULL;
 		goto out;
 	}
 
 	if (strcmp(lock_tag, RBD_LOCK_TAG)) {
 		rbd_warn(rbd_dev, "locked by external mechanism, tag %s",
 			 lock_tag);
-		ret = -EBUSY;
-		goto out;
+		goto err_busy;
 	}
 
 	if (lock_type == CEPH_CLS_LOCK_SHARED) {
 		rbd_warn(rbd_dev, "shared lock type detected");
-		ret = -EBUSY;
-		goto out;
+		goto err_busy;
 	}
 
-	if (strncmp((*lockers)[0].id.cookie, RBD_LOCK_COOKIE_PREFIX,
+	WARN_ON(num_lockers != 1);
+	if (strncmp(lockers[0].id.cookie, RBD_LOCK_COOKIE_PREFIX,
 		    strlen(RBD_LOCK_COOKIE_PREFIX))) {
 		rbd_warn(rbd_dev, "locked by external mechanism, cookie %s",
-			 (*lockers)[0].id.cookie);
-		ret = -EBUSY;
-		goto out;
+			 lockers[0].id.cookie);
+		goto err_busy;
 	}
 
 out:
 	kfree(lock_tag);
-	return ret;
+	return lockers;
+
+err_busy:
+	kfree(lock_tag);
+	ceph_free_lockers(lockers, num_lockers);
+	return ERR_PTR(-EBUSY);
 }
 
 static int find_watcher(struct rbd_device *rbd_dev,
@@ -3948,51 +3961,56 @@ static int find_watcher(struct rbd_device *rbd_dev,
 static int rbd_try_lock(struct rbd_device *rbd_dev)
 {
 	struct ceph_client *client = rbd_dev->rbd_client->client;
-	struct ceph_locker *lockers;
-	u32 num_lockers;
+	struct ceph_locker *locker;
 	int ret;
 
 	for (;;) {
+		locker = NULL;
+
 		ret = rbd_lock(rbd_dev);
 		if (ret != -EBUSY)
-			return ret;
+			goto out;
 
 		/* determine if the current lock holder is still alive */
-		ret = get_lock_owner_info(rbd_dev, &lockers, &num_lockers);
-		if (ret)
-			return ret;
-
-		if (num_lockers == 0)
+		locker = get_lock_owner_info(rbd_dev);
+		if (IS_ERR(locker)) {
+			ret = PTR_ERR(locker);
+			locker = NULL;
+			goto out;
+		}
+		if (!locker)
 			goto again;
 
-		ret = find_watcher(rbd_dev, lockers);
+		ret = find_watcher(rbd_dev, locker);
 		if (ret)
 			goto out; /* request lock or error */
 
 		rbd_warn(rbd_dev, "breaking header lock owned by %s%llu",
-			 ENTITY_NAME(lockers[0].id.name));
+			 ENTITY_NAME(locker->id.name));
 
 		ret = ceph_monc_blocklist_add(&client->monc,
-					      &lockers[0].info.addr);
+					      &locker->info.addr);
 		if (ret) {
-			rbd_warn(rbd_dev, "blocklist of %s%llu failed: %d",
-				 ENTITY_NAME(lockers[0].id.name), ret);
+			rbd_warn(rbd_dev, "failed to blocklist %s%llu: %d",
+				 ENTITY_NAME(locker->id.name), ret);
 			goto out;
 		}
 
 		ret = ceph_cls_break_lock(&client->osdc, &rbd_dev->header_oid,
 					  &rbd_dev->header_oloc, RBD_LOCK_NAME,
-					  lockers[0].id.cookie,
-					  &lockers[0].id.name);
-		if (ret && ret != -ENOENT)
+					  locker->id.cookie, &locker->id.name);
+		if (ret && ret != -ENOENT) {
+			rbd_warn(rbd_dev, "failed to break header lock: %d",
+				 ret);
 			goto out;
+		}
 
 again:
-		ceph_free_lockers(lockers, num_lockers);
+		free_locker(locker);
 	}
 
 out:
-	ceph_free_lockers(lockers, num_lockers);
+	free_locker(locker);
 	return ret;
 }
 
-- 
2.40.1

[PATCH AUTOSEL 6.1 43/47] rbd: harden get_lock_owner_info() a bit

[Sasha Levin]

From: Ilya Dryomov <idryomov@gmail.com>

[ Upstream commit 8ff2c64c9765446c3cef804fb99da04916603e27 ]

- we want the exclusive lock type, so test for it directly
- use sscanf() to actually parse the lock cookie and avoid admitting
  invalid handles
- bail if locker has a blank address

Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Dongsheng Yang <dongsheng.yang@easystack.cn>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/block/rbd.c  | 21 +++++++++++++++------
 net/ceph/messenger.c |  1 +
 2 files changed, 16 insertions(+), 6 deletions(-)

diff --git a/drivers/block/rbd.c b/drivers/block/rbd.c
index 523a903d6ae5f..2615ab99eb9aa 100644
--- a/drivers/block/rbd.c
+++ b/drivers/block/rbd.c
@@ -3863,10 +3863,9 @@ static struct ceph_locker *get_lock_owner_info(struct rbd_device *rbd_dev)
 	u32 num_lockers;
 	u8 lock_type;
 	char *lock_tag;
+	u64 handle;
 	int ret;
 
-	dout("%s rbd_dev %p\n", __func__, rbd_dev);
-
 	ret = ceph_cls_lock_info(osdc, &rbd_dev->header_oid,
 				 &rbd_dev->header_oloc, RBD_LOCK_NAME,
 				 &lock_type, &lock_tag, &lockers, &num_lockers);
@@ -3887,18 +3886,28 @@ static struct ceph_locker *get_lock_owner_info(struct rbd_device *rbd_dev)
 		goto err_busy;
 	}
 
-	if (lock_type == CEPH_CLS_LOCK_SHARED) {
-		rbd_warn(rbd_dev, "shared lock type detected");
+	if (lock_type != CEPH_CLS_LOCK_EXCLUSIVE) {
+		rbd_warn(rbd_dev, "incompatible lock type detected");
 		goto err_busy;
 	}
 
 	WARN_ON(num_lockers != 1);
-	if (strncmp(lockers[0].id.cookie, RBD_LOCK_COOKIE_PREFIX,
-		    strlen(RBD_LOCK_COOKIE_PREFIX))) {
+	ret = sscanf(lockers[0].id.cookie, RBD_LOCK_COOKIE_PREFIX " %llu",
+		     &handle);
+	if (ret != 1) {
 		rbd_warn(rbd_dev, "locked by external mechanism, cookie %s",
 			 lockers[0].id.cookie);
 		goto err_busy;
 	}
+	if (ceph_addr_is_blank(&lockers[0].info.addr)) {
+		rbd_warn(rbd_dev, "locker has a blank address");
+		goto err_busy;
+	}
+
+	dout("%s rbd_dev %p got locker %s%llu@%pISpc/%u handle %llu\n",
+	     __func__, rbd_dev, ENTITY_NAME(lockers[0].id.name),
+	     &lockers[0].info.addr.in_addr,
+	     le32_to_cpu(lockers[0].info.addr.nonce), handle);
 
 out:
 	kfree(lock_tag);
diff --git a/net/ceph/messenger.c b/net/ceph/messenger.c
index dfa237fbd5a32..09feb3f1fcaa3 100644
--- a/net/ceph/messenger.c
+++ b/net/ceph/messenger.c
@@ -1118,6 +1118,7 @@ bool ceph_addr_is_blank(const struct ceph_entity_addr *addr)
 		return true;
 	}
 }
+EXPORT_SYMBOL(ceph_addr_is_blank);
 
 int ceph_addr_port(const struct ceph_entity_addr *addr)
 {
-- 
2.40.1

[PATCH AUTOSEL 6.1 44/47] ALSA: usb-audio: Update for native DSD support quirks

[Sasha Levin]

From: Jussi Laako <jussi@sonarnerd.net>

[ Upstream commit f7fea075edfa085c25eb34c44ceacf3602537f98 ]

Maintenance patch for native DSD support.

Remove incorrect T+A device quirks. Move set of device quirks to vendor
quirks. Add set of missing device and vendor quirks.

Signed-off-by: Jussi Laako <jussi@sonarnerd.net>
Link: https://lore.kernel.org/r/20230726165645.404311-1-jussi@sonarnerd.net
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/usb/quirks.c | 34 ++++++++++++++++++++++++++++------
 1 file changed, 28 insertions(+), 6 deletions(-)

diff --git a/sound/usb/quirks.c b/sound/usb/quirks.c
index d4a7ffef82194..4667d543f7481 100644
--- a/sound/usb/quirks.c
+++ b/sound/usb/quirks.c
@@ -1874,8 +1874,10 @@ u64 snd_usb_interface_dsd_format_quirks(struct snd_usb_audio *chip,
 
 	/* XMOS based USB DACs */
 	switch (chip->usb_id) {
-	case USB_ID(0x1511, 0x0037): /* AURALiC VEGA */
-	case USB_ID(0x21ed, 0xd75a): /* Accuphase DAC-60 option card */
+	case USB_ID(0x139f, 0x5504): /* Nagra DAC */
+	case USB_ID(0x20b1, 0x3089): /* Mola-Mola DAC */
+	case USB_ID(0x2522, 0x0007): /* LH Labs Geek Out 1V5 */
+	case USB_ID(0x2522, 0x0009): /* LH Labs Geek Pulse X Inifinity 2V0 */
 	case USB_ID(0x2522, 0x0012): /* LH Labs VI DAC Infinity */
 	case USB_ID(0x2772, 0x0230): /* Pro-Ject Pre Box S2 Digital */
 		if (fp->altsetting == 2)
@@ -1885,14 +1887,18 @@ u64 snd_usb_interface_dsd_format_quirks(struct snd_usb_audio *chip,
 	case USB_ID(0x0d8c, 0x0316): /* Hegel HD12 DSD */
 	case USB_ID(0x10cb, 0x0103): /* The Bit Opus #3; with fp->dsd_raw */
 	case USB_ID(0x16d0, 0x06b2): /* NuPrime DAC-10 */
-	case USB_ID(0x16d0, 0x09dd): /* Encore mDSD */
+	case USB_ID(0x16d0, 0x06b4): /* NuPrime Audio HD-AVP/AVA */
 	case USB_ID(0x16d0, 0x0733): /* Furutech ADL Stratos */
+	case USB_ID(0x16d0, 0x09d8): /* NuPrime IDA-8 */
 	case USB_ID(0x16d0, 0x09db): /* NuPrime Audio DAC-9 */
+	case USB_ID(0x16d0, 0x09dd): /* Encore mDSD */
 	case USB_ID(0x1db5, 0x0003): /* Bryston BDA3 */
+	case USB_ID(0x20a0, 0x4143): /* WaveIO USB Audio 2.0 */
 	case USB_ID(0x22e1, 0xca01): /* HDTA Serenade DSD */
 	case USB_ID(0x249c, 0x9326): /* M2Tech Young MkIII */
 	case USB_ID(0x2616, 0x0106): /* PS Audio NuWave DAC */
 	case USB_ID(0x2622, 0x0041): /* Audiolab M-DAC+ */
+	case USB_ID(0x278b, 0x5100): /* Rotel RC-1590 */
 	case USB_ID(0x27f7, 0x3002): /* W4S DAC-2v2SE */
 	case USB_ID(0x29a2, 0x0086): /* Mutec MC3+ USB */
 	case USB_ID(0x6b42, 0x0042): /* MSB Technology */
@@ -1902,9 +1908,6 @@ u64 snd_usb_interface_dsd_format_quirks(struct snd_usb_audio *chip,
 
 	/* Amanero Combo384 USB based DACs with native DSD support */
 	case USB_ID(0x16d0, 0x071a):  /* Amanero - Combo384 */
-	case USB_ID(0x2ab6, 0x0004):  /* T+A DAC8DSD-V2.0, MP1000E-V2.0, MP2000R-V2.0, MP2500R-V2.0, MP3100HV-V2.0 */
-	case USB_ID(0x2ab6, 0x0005):  /* T+A USB HD Audio 1 */
-	case USB_ID(0x2ab6, 0x0006):  /* T+A USB HD Audio 2 */
 		if (fp->altsetting == 2) {
 			switch (le16_to_cpu(chip->dev->descriptor.bcdDevice)) {
 			case 0x199:
@@ -2049,6 +2052,9 @@ static const struct usb_audio_quirk_flags_table quirk_flags_table[] = {
 		   QUIRK_FLAG_IFACE_DELAY),
 	DEVICE_FLG(0x0644, 0x805f, /* TEAC Model 12 */
 		   QUIRK_FLAG_FORCE_IFACE_RESET),
+	DEVICE_FLG(0x0644, 0x806b, /* TEAC UD-701 */
+		   QUIRK_FLAG_ITF_USB_DSD_DAC | QUIRK_FLAG_CTL_MSG_DELAY |
+		   QUIRK_FLAG_IFACE_DELAY),
 	DEVICE_FLG(0x06f8, 0xb000, /* Hercules DJ Console (Windows Edition) */
 		   QUIRK_FLAG_IGNORE_CTL_ERROR),
 	DEVICE_FLG(0x06f8, 0xd002, /* Hercules DJ Console (Macintosh Edition) */
@@ -2087,6 +2093,8 @@ static const struct usb_audio_quirk_flags_table quirk_flags_table[] = {
 		   QUIRK_FLAG_ITF_USB_DSD_DAC | QUIRK_FLAG_CTL_MSG_DELAY),
 	DEVICE_FLG(0x154e, 0x3006, /* Marantz SA-14S1 */
 		   QUIRK_FLAG_ITF_USB_DSD_DAC | QUIRK_FLAG_CTL_MSG_DELAY),
+	DEVICE_FLG(0x154e, 0x300b, /* Marantz SA-KI RUBY / SA-12 */
+		   QUIRK_FLAG_DSD_RAW),
 	DEVICE_FLG(0x154e, 0x500e, /* Denon DN-X1600 */
 		   QUIRK_FLAG_IGNORE_CLOCK_SOURCE),
 	DEVICE_FLG(0x1686, 0x00dd, /* Zoom R16/24 */
@@ -2131,6 +2139,10 @@ static const struct usb_audio_quirk_flags_table quirk_flags_table[] = {
 		   QUIRK_FLAG_SHARE_MEDIA_DEVICE | QUIRK_FLAG_ALIGN_TRANSFER),
 	DEVICE_FLG(0x21b4, 0x0081, /* AudioQuest DragonFly */
 		   QUIRK_FLAG_GET_SAMPLE_RATE),
+	DEVICE_FLG(0x21b4, 0x0230, /* Ayre QB-9 Twenty */
+		   QUIRK_FLAG_DSD_RAW),
+	DEVICE_FLG(0x21b4, 0x0232, /* Ayre QX-5 Twenty */
+		   QUIRK_FLAG_DSD_RAW),
 	DEVICE_FLG(0x2522, 0x0007, /* LH Labs Geek Out HD Audio 1V5 */
 		   QUIRK_FLAG_SET_IFACE_FIRST),
 	DEVICE_FLG(0x2708, 0x0002, /* Audient iD14 */
@@ -2173,12 +2185,18 @@ static const struct usb_audio_quirk_flags_table quirk_flags_table[] = {
 		   QUIRK_FLAG_VALIDATE_RATES),
 	VENDOR_FLG(0x1235, /* Focusrite Novation */
 		   QUIRK_FLAG_VALIDATE_RATES),
+	VENDOR_FLG(0x1511, /* AURALiC */
+		   QUIRK_FLAG_DSD_RAW),
 	VENDOR_FLG(0x152a, /* Thesycon devices */
 		   QUIRK_FLAG_DSD_RAW),
+	VENDOR_FLG(0x18d1, /* iBasso devices */
+		   QUIRK_FLAG_DSD_RAW),
 	VENDOR_FLG(0x1de7, /* Phoenix Audio */
 		   QUIRK_FLAG_GET_SAMPLE_RATE),
 	VENDOR_FLG(0x20b1, /* XMOS based devices */
 		   QUIRK_FLAG_DSD_RAW),
+	VENDOR_FLG(0x21ed, /* Accuphase Laboratory */
+		   QUIRK_FLAG_DSD_RAW),
 	VENDOR_FLG(0x22d9, /* Oppo */
 		   QUIRK_FLAG_DSD_RAW),
 	VENDOR_FLG(0x23ba, /* Playback Design */
@@ -2194,10 +2212,14 @@ static const struct usb_audio_quirk_flags_table quirk_flags_table[] = {
 		   QUIRK_FLAG_DSD_RAW),
 	VENDOR_FLG(0x2ab6, /* T+A devices */
 		   QUIRK_FLAG_DSD_RAW),
+	VENDOR_FLG(0x2d87, /* Cayin device */
+		   QUIRK_FLAG_DSD_RAW),
 	VENDOR_FLG(0x3336, /* HEM devices */
 		   QUIRK_FLAG_DSD_RAW),
 	VENDOR_FLG(0x3353, /* Khadas devices */
 		   QUIRK_FLAG_DSD_RAW),
+	VENDOR_FLG(0x35f4, /* MSB Technology */
+		   QUIRK_FLAG_DSD_RAW),
 	VENDOR_FLG(0x3842, /* EVGA */
 		   QUIRK_FLAG_DSD_RAW),
 	VENDOR_FLG(0xc502, /* HiBy devices */
-- 
2.40.1

[PATCH AUTOSEL 6.1 45/47] staging: fbtft: ili9341: use macro FBTFT_REGISTER_SPI_DRIVER

[Sasha Levin]

From: Raphael Gallais-Pou <rgallaispou@gmail.com>

[ Upstream commit 4912649e1cf0317bf563f91655e04a303cacaf8d ]

Using FBTFT_REGISTER_DRIVER resolves to a NULL struct spi_device_id. This
ultimately causes a warning when the module probes. Fixes it.

Signed-off-by: Raphael Gallais-Pou <rgallaispou@gmail.com>
Link: https://lore.kernel.org/r/20230718172024.67488-1-rgallaispou@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/staging/fbtft/fb_ili9341.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/staging/fbtft/fb_ili9341.c b/drivers/staging/fbtft/fb_ili9341.c
index 9ccd0823c3ab3..47e72b87d76d9 100644
--- a/drivers/staging/fbtft/fb_ili9341.c
+++ b/drivers/staging/fbtft/fb_ili9341.c
@@ -145,7 +145,7 @@ static struct fbtft_display display = {
 	},
 };
 
-FBTFT_REGISTER_DRIVER(DRVNAME, "ilitek,ili9341", &display);
+FBTFT_REGISTER_SPI_DRIVER(DRVNAME, "ilitek", "ili9341", &display);
 
 MODULE_ALIAS("spi:" DRVNAME);
 MODULE_ALIAS("platform:" DRVNAME);
-- 
2.40.1

[PATCH AUTOSEL 6.1 46/47] security: keys: perform capable check only on privileged operations

[Sasha Levin]

From: Christian Göttsche <cgzones@googlemail.com>

[ Upstream commit 2d7f105edbb3b2be5ffa4d833abbf9b6965e9ce7 ]

If the current task fails the check for the queried capability via
`capable(CAP_SYS_ADMIN)` LSMs like SELinux generate a denial message.
Issuing such denial messages unnecessarily can lead to a policy author
granting more privileges to a subject than needed to silence them.

Reorder CAP_SYS_ADMIN checks after the check whether the operation is
actually privileged.

Signed-off-by: Christian Göttsche <cgzones@googlemail.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 security/keys/keyctl.c | 11 ++++++++---
 1 file changed, 8 insertions(+), 3 deletions(-)

diff --git a/security/keys/keyctl.c b/security/keys/keyctl.c
index d54f73c558f72..19be69fa4d052 100644
--- a/security/keys/keyctl.c
+++ b/security/keys/keyctl.c
@@ -980,14 +980,19 @@ long keyctl_chown_key(key_serial_t id, uid_t user, gid_t group)
 	ret = -EACCES;
 	down_write(&key->sem);
 
-	if (!capable(CAP_SYS_ADMIN)) {
+	{
+		bool is_privileged_op = false;
+
 		/* only the sysadmin can chown a key to some other UID */
 		if (user != (uid_t) -1 && !uid_eq(key->uid, uid))
-			goto error_put;
+			is_privileged_op = true;
 
 		/* only the sysadmin can set the key's GID to a group other
 		 * than one of those that the current process subscribes to */
 		if (group != (gid_t) -1 && !gid_eq(gid, key->gid) && !in_group_p(gid))
+			is_privileged_op = true;
+
+		if (is_privileged_op && !capable(CAP_SYS_ADMIN))
 			goto error_put;
 	}
 
@@ -1088,7 +1093,7 @@ long keyctl_setperm_key(key_serial_t id, key_perm_t perm)
 	down_write(&key->sem);
 
 	/* if we're not the sysadmin, we can only change a key that we own */
-	if (capable(CAP_SYS_ADMIN) || uid_eq(key->uid, current_fsuid())) {
+	if (uid_eq(key->uid, current_fsuid()) || capable(CAP_SYS_ADMIN)) {
 		key->perm = perm;
 		notify_key(key, NOTIFY_KEY_SETATTR, 0);
 		ret = 0;
-- 
2.40.1

[PATCH AUTOSEL 6.1 47/47] kprobes: Prohibit probing on CFI preamble symbol

[Sasha Levin]

From: "Masami Hiramatsu (Google)" <mhiramat@kernel.org>

[ Upstream commit de02f2ac5d8cfb311f44f2bf144cc20002f1fbbd ]

Do not allow to probe on "__cfi_" or "__pfx_" started symbol, because those
are used for CFI and not executed. Probing it will break the CFI.

Link: https://lore.kernel.org/all/168904024679.116016.18089228029322008512.stgit@devnote2/

Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 kernel/kprobes.c | 14 +++++++++++++-
 1 file changed, 13 insertions(+), 1 deletion(-)

diff --git a/kernel/kprobes.c b/kernel/kprobes.c
index 00e177de91ccd..3da9726232ff9 100644
--- a/kernel/kprobes.c
+++ b/kernel/kprobes.c
@@ -1545,6 +1545,17 @@ static int check_ftrace_location(struct kprobe *p)
 	return 0;
 }
 
+static bool is_cfi_preamble_symbol(unsigned long addr)
+{
+	char symbuf[KSYM_NAME_LEN];
+
+	if (lookup_symbol_name(addr, symbuf))
+		return false;
+
+	return str_has_prefix("__cfi_", symbuf) ||
+		str_has_prefix("__pfx_", symbuf);
+}
+
 static int check_kprobe_address_safe(struct kprobe *p,
 				     struct module **probed_mod)
 {
@@ -1563,7 +1574,8 @@ static int check_kprobe_address_safe(struct kprobe *p,
 	    within_kprobe_blacklist((unsigned long) p->addr) ||
 	    jump_label_text_reserved(p->addr, p->addr) ||
 	    static_call_text_reserved(p->addr, p->addr) ||
-	    find_bug((unsigned long)p->addr)) {
+	    find_bug((unsigned long)p->addr) ||
+	    is_cfi_preamble_symbol((unsigned long)p->addr)) {
 		ret = -EINVAL;
 		goto out;
 	}
-- 
2.40.1