* [PATCH v2 0/6] dts: qcom: Introduce SM8750 device trees
@ 2024-11-12 0:49 Melody Olvera
2024-11-12 0:49 ` [PATCH v2 1/6] dt-bindings: arm: qcom: Document sm8750 SoC and boards Melody Olvera
` (5 more replies)
0 siblings, 6 replies; 12+ messages in thread
From: Melody Olvera @ 2024-11-12 0:49 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Catalin Marinas, Will Deacon, Geert Uytterhoeven,
Dmitry Baryshkov, Neil Armstrong, Arnd Bergmann,
Nícolas F . R . A . Prado, Trilok Soni,
Satya Durga Srinivasu Prabhala
Cc: linux-arm-msm, devicetree, linux-kernel, linux-arm-kernel, Melody Olvera
This series adds the initial device tree support for the SM8750 SoCs
needed to boot to shell. This specifically adds support for clocks,
pinctrl, rpmhpd, regulators, interconnects, and SoC and board
compatibles.
The Qualcomm Technologies, Inc. SM8750 SoC is the latest in the line of
consumer mobile device SoCs. See more at:
https://www.qualcomm.com/content/dam/qcomm-martech/dm-assets/images/company/news-media/media-center/press-kits/snapdragon-summit-2024/day-1/documents/Snapdragon8EliteProductBrief.pdf
Dependencies:
clks: https://lore.kernel.org/all/20241112002807.2804021-1-quic_molvera@quicinc.com/
interconnects: https://lore.kernel.org/all/20241112003017.2805670-1-quic_molvera@quicinc.com/
pinctrl: https://lore.kernel.org/all/20241112002843.2804490-1-quic_molvera@quicinc.com/
regulators: https://lore.kernel.org/all/20241112002645.2803506-1-quic_molvera@quicinc.com/
power domains: https://lore.kernel.org/all/20241112002444.2802092-1-quic_molvera@quicinc.com/
misc bindings:
- https://lore.kernel.org/all/20241112003544.2807368-1-quic_molvera@quicinc.com/
- https://lore.kernel.org/all/20241112003217.2806556-1-quic_molvera@quicinc.com/
- https://lore.kernel.org/all/20241021230500.2632527-1-quic_molvera@quicinc.com/
- https://lore.kernel.org/all/20241021230439.2632480-1-quic_molvera@quicinc.com/
applied bindings:
- https://lore.kernel.org/all/20241021230427.2632466-1-quic_molvera@quicinc.com/
Changes in V2:
- split dts and dtsi patches into separate patches
- changed eusb-repeater to phy
- removed empty chosen node
- lowercased phandles in dtsi
- added system-wide domain idle state
- added leading zeroes to applicable regs
- corrected gpio ranges
- removed some unnecessary comments
- updated timer size cells
- separated pmics & thermal zones into their own file
- added chassis type to board files
- added reserved tlmm nodes to board files
- corrected regulator-0 supplies in board files
Jishnu Prakash (1):
arm64: dts: qcom: Add pmd8028 and pmih0108 PMICs
Melody Olvera (5):
dt-bindings: arm: qcom: Document sm8750 SoC and boards
arm64: dts: qcom: Add base SM8750 dtsi
arm64: dts: qcom: sm8750: Add pmic dtsi
arm64: dts: qcom: Add SM8750 MTP and QRD boards
arm64: defconfig: Enable SM8750 SoC base configs
.../devicetree/bindings/arm/qcom.yaml | 7 +
arch/arm64/boot/dts/qcom/Makefile | 2 +
arch/arm64/boot/dts/qcom/pmd8028.dtsi | 56 +
arch/arm64/boot/dts/qcom/pmih0108.dtsi | 62 +
arch/arm64/boot/dts/qcom/sm8750-mtp.dts | 794 +++++
arch/arm64/boot/dts/qcom/sm8750-pmics.dtsi | 188 ++
arch/arm64/boot/dts/qcom/sm8750-qrd.dts | 792 +++++
arch/arm64/boot/dts/qcom/sm8750.dtsi | 2917 +++++++++++++++++
arch/arm64/configs/defconfig | 4 +
9 files changed, 4822 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/pmd8028.dtsi
create mode 100644 arch/arm64/boot/dts/qcom/pmih0108.dtsi
create mode 100644 arch/arm64/boot/dts/qcom/sm8750-mtp.dts
create mode 100644 arch/arm64/boot/dts/qcom/sm8750-pmics.dtsi
create mode 100644 arch/arm64/boot/dts/qcom/sm8750-qrd.dts
create mode 100644 arch/arm64/boot/dts/qcom/sm8750.dtsi
base-commit: 6d59cab07b8d74d0f0422b750038123334f6ecc2
--
2.46.1
^ permalink raw reply [flat|nested] 12+ messages in thread* [PATCH v2 1/6] dt-bindings: arm: qcom: Document sm8750 SoC and boards 2024-11-12 0:49 [PATCH v2 0/6] dts: qcom: Introduce SM8750 device trees Melody Olvera @ 2024-11-12 0:49 ` Melody Olvera 2024-11-15 14:49 ` Dmitry Baryshkov 2024-11-12 0:49 ` [PATCH v2 2/6] arm64: dts: qcom: Add pmd8028 and pmih0108 PMICs Melody Olvera ` (4 subsequent siblings) 5 siblings, 1 reply; 12+ messages in thread From: Melody Olvera @ 2024-11-12 0:49 UTC (permalink / raw) To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Catalin Marinas, Will Deacon, Geert Uytterhoeven, Dmitry Baryshkov, Neil Armstrong, Arnd Bergmann, Nícolas F . R . A . Prado, Trilok Soni, Satya Durga Srinivasu Prabhala Cc: linux-arm-msm, devicetree, linux-kernel, linux-arm-kernel, Melody Olvera, Krzysztof Kozlowski Document the SM8750 SoC binding and the boards which use it. Signed-off-by: Melody Olvera <quic_molvera@quicinc.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> --- Documentation/devicetree/bindings/arm/qcom.yaml | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml index 7c8c3a97506a..f4e8f8821405 100644 --- a/Documentation/devicetree/bindings/arm/qcom.yaml +++ b/Documentation/devicetree/bindings/arm/qcom.yaml @@ -86,6 +86,7 @@ description: | sm8450 sm8550 sm8650 + sm8750 x1e80100 There are many devices in the list below that run the standard ChromeOS @@ -1077,6 +1078,12 @@ properties: - qcom,sm8650-qrd - const: qcom,sm8650 + - items: + - enum: + - qcom,sm8750-mtp + - qcom,sm8750-qrd + - const: qcom,sm8750 + - items: - enum: - qcom,x1e001de-devkit -- 2.46.1 ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v2 1/6] dt-bindings: arm: qcom: Document sm8750 SoC and boards 2024-11-12 0:49 ` [PATCH v2 1/6] dt-bindings: arm: qcom: Document sm8750 SoC and boards Melody Olvera @ 2024-11-15 14:49 ` Dmitry Baryshkov 2024-11-18 22:08 ` Melody Olvera 0 siblings, 1 reply; 12+ messages in thread From: Dmitry Baryshkov @ 2024-11-15 14:49 UTC (permalink / raw) To: Melody Olvera Cc: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Catalin Marinas, Will Deacon, Geert Uytterhoeven, Neil Armstrong, Arnd Bergmann, Nícolas F . R . A . Prado, Trilok Soni, Satya Durga Srinivasu Prabhala, linux-arm-msm, devicetree, linux-kernel, linux-arm-kernel, Krzysztof Kozlowski On Mon, Nov 11, 2024 at 04:49:31PM -0800, Melody Olvera wrote: > Document the SM8750 SoC binding and the boards which use it. Nit: In subject you have 'sm8750'. Please use single style for all SoC names (I think it's preferred to use uppercase). > > Signed-off-by: Melody Olvera <quic_molvera@quicinc.com> > Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> > --- > Documentation/devicetree/bindings/arm/qcom.yaml | 7 +++++++ > 1 file changed, 7 insertions(+) > > diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml > index 7c8c3a97506a..f4e8f8821405 100644 > --- a/Documentation/devicetree/bindings/arm/qcom.yaml > +++ b/Documentation/devicetree/bindings/arm/qcom.yaml > @@ -86,6 +86,7 @@ description: | > sm8450 > sm8550 > sm8650 > + sm8750 > x1e80100 > > There are many devices in the list below that run the standard ChromeOS > @@ -1077,6 +1078,12 @@ properties: > - qcom,sm8650-qrd > - const: qcom,sm8650 > > + - items: > + - enum: > + - qcom,sm8750-mtp > + - qcom,sm8750-qrd > + - const: qcom,sm8750 > + > - items: > - enum: > - qcom,x1e001de-devkit > -- > 2.46.1 > -- With best wishes Dmitry ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v2 1/6] dt-bindings: arm: qcom: Document sm8750 SoC and boards 2024-11-15 14:49 ` Dmitry Baryshkov @ 2024-11-18 22:08 ` Melody Olvera 0 siblings, 0 replies; 12+ messages in thread From: Melody Olvera @ 2024-11-18 22:08 UTC (permalink / raw) To: Dmitry Baryshkov Cc: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Catalin Marinas, Will Deacon, Geert Uytterhoeven, Neil Armstrong, Arnd Bergmann, Nícolas F . R . A . Prado, Trilok Soni, Satya Durga Srinivasu Prabhala, linux-arm-msm, devicetree, linux-kernel, linux-arm-kernel, Krzysztof Kozlowski On 11/15/2024 6:49 AM, Dmitry Baryshkov wrote: > On Mon, Nov 11, 2024 at 04:49:31PM -0800, Melody Olvera wrote: >> Document the SM8750 SoC binding and the boards which use it. > Nit: In subject you have 'sm8750'. Please use single style for all SoC > names (I think it's preferred to use uppercase). Sure thing. Will use upper case. Thanks, Melody > >> Signed-off-by: Melody Olvera <quic_molvera@quicinc.com> >> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> >> --- >> Documentation/devicetree/bindings/arm/qcom.yaml | 7 +++++++ >> 1 file changed, 7 insertions(+) >> >> diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml >> index 7c8c3a97506a..f4e8f8821405 100644 >> --- a/Documentation/devicetree/bindings/arm/qcom.yaml >> +++ b/Documentation/devicetree/bindings/arm/qcom.yaml >> @@ -86,6 +86,7 @@ description: | >> sm8450 >> sm8550 >> sm8650 >> + sm8750 >> x1e80100 >> >> There are many devices in the list below that run the standard ChromeOS >> @@ -1077,6 +1078,12 @@ properties: >> - qcom,sm8650-qrd >> - const: qcom,sm8650 >> >> + - items: >> + - enum: >> + - qcom,sm8750-mtp >> + - qcom,sm8750-qrd >> + - const: qcom,sm8750 >> + >> - items: >> - enum: >> - qcom,x1e001de-devkit >> -- >> 2.46.1 >> ^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v2 2/6] arm64: dts: qcom: Add pmd8028 and pmih0108 PMICs 2024-11-12 0:49 [PATCH v2 0/6] dts: qcom: Introduce SM8750 device trees Melody Olvera 2024-11-12 0:49 ` [PATCH v2 1/6] dt-bindings: arm: qcom: Document sm8750 SoC and boards Melody Olvera @ 2024-11-12 0:49 ` Melody Olvera 2024-11-15 14:58 ` Dmitry Baryshkov 2024-11-12 0:49 ` [PATCH v2 3/6] arm64: dts: qcom: Add base SM8750 dtsi Melody Olvera ` (3 subsequent siblings) 5 siblings, 1 reply; 12+ messages in thread From: Melody Olvera @ 2024-11-12 0:49 UTC (permalink / raw) To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Catalin Marinas, Will Deacon, Geert Uytterhoeven, Dmitry Baryshkov, Neil Armstrong, Arnd Bergmann, Nícolas F . R . A . Prado, Trilok Soni, Satya Durga Srinivasu Prabhala Cc: linux-arm-msm, devicetree, linux-kernel, linux-arm-kernel, Jishnu Prakash, Melody Olvera From: Jishnu Prakash <quic_jprakash@quicinc.com> Add descriptions of pmd8028 and pmih0108 PMICs used on SM8750 platforms. Signed-off-by: Jishnu Prakash <quic_jprakash@quicinc.com> Signed-off-by: Melody Olvera <quic_molvera@quicinc.com> --- arch/arm64/boot/dts/qcom/pmd8028.dtsi | 56 +++++++++++++++++++++++ arch/arm64/boot/dts/qcom/pmih0108.dtsi | 62 ++++++++++++++++++++++++++ 2 files changed, 118 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/pmd8028.dtsi create mode 100644 arch/arm64/boot/dts/qcom/pmih0108.dtsi diff --git a/arch/arm64/boot/dts/qcom/pmd8028.dtsi b/arch/arm64/boot/dts/qcom/pmd8028.dtsi new file mode 100644 index 000000000000..f8ef8e133854 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/pmd8028.dtsi @@ -0,0 +1,56 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved. + */ + +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/spmi/spmi.h> + +/ { + thermal-zones { + pmd8028-thermal { + polling-delay-passive = <100>; + thermal-sensors = <&pmd8028_temp_alarm>; + + trips { + pmd8028_trip0: trip0 { + temperature = <95000>; + hysteresis = <0>; + type = "passive"; + }; + + pmd8028_trip1: trip1 { + temperature = <115000>; + hysteresis = <0>; + type = "hot"; + }; + }; + }; + }; +}; + +&spmi_bus { + pmd8028: pmic@4 { + compatible = "qcom,pmd8028", "qcom,spmi-pmic"; + reg = <0x4 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pmd8028_temp_alarm: temp-alarm@a00 { + compatible = "qcom,spmi-temp-alarm"; + reg = <0xa00>; + interrupts = <0x4 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; + #thermal-sensor-cells = <0>; + }; + + pmd8028_gpios: gpio@8800 { + compatible = "qcom,pmd8028-gpio", "qcom,spmi-gpio"; + reg = <0x8800>; + gpio-controller; + gpio-ranges = <&pmd8028_gpios 0 0 4>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/pmih0108.dtsi b/arch/arm64/boot/dts/qcom/pmih0108.dtsi new file mode 100644 index 000000000000..3907d8fbcf78 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/pmih0108.dtsi @@ -0,0 +1,62 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved. + */ + +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/spmi/spmi.h> + +/ { + thermal-zones { + pmih0108-thermal { + polling-delay-passive = <100>; + thermal-sensors = <&pmih0108_temp_alarm>; + + trips { + trip0 { + temperature = <95000>; + hysteresis = <0>; + type = "passive"; + }; + + trip1 { + temperature = <115000>; + hysteresis = <0>; + type = "hot"; + }; + }; + }; + }; +}; + +&spmi_bus { + pmih0108: pmic@7 { + compatible = "qcom,pmih0108", "qcom,spmi-pmic"; + reg = <0x7 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pmih0108_temp_alarm: temp-alarm@a00 { + compatible = "qcom,spmi-temp-alarm"; + reg = <0xa00>; + interrupts = <0x7 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; + #thermal-sensor-cells = <0>; + }; + + pmih0108_gpios: gpio@8800 { + compatible = "qcom,pmih0108-gpio", "qcom,spmi-gpio"; + reg = <0x8800>; + gpio-controller; + gpio-ranges = <&pmih0108_gpios 0 0 18>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + pmih0108_eusb2_repeater: phy@fd00 { + compatible = "qcom,pm8550b-eusb2-repeater"; + reg = <0xfd00>; + #phy-cells = <0>; + }; + }; +}; -- 2.46.1 ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v2 2/6] arm64: dts: qcom: Add pmd8028 and pmih0108 PMICs 2024-11-12 0:49 ` [PATCH v2 2/6] arm64: dts: qcom: Add pmd8028 and pmih0108 PMICs Melody Olvera @ 2024-11-15 14:58 ` Dmitry Baryshkov 2024-11-18 22:16 ` Melody Olvera 0 siblings, 1 reply; 12+ messages in thread From: Dmitry Baryshkov @ 2024-11-15 14:58 UTC (permalink / raw) To: Melody Olvera Cc: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Catalin Marinas, Will Deacon, Geert Uytterhoeven, Neil Armstrong, Arnd Bergmann, Nícolas F . R . A . Prado, Trilok Soni, Satya Durga Srinivasu Prabhala, linux-arm-msm, devicetree, linux-kernel, linux-arm-kernel, Jishnu Prakash On Mon, Nov 11, 2024 at 04:49:32PM -0800, Melody Olvera wrote: > From: Jishnu Prakash <quic_jprakash@quicinc.com> > > Add descriptions of pmd8028 and pmih0108 PMICs used on SM8750 > platforms. Up/lower case? > > Signed-off-by: Jishnu Prakash <quic_jprakash@quicinc.com> > Signed-off-by: Melody Olvera <quic_molvera@quicinc.com> > --- > arch/arm64/boot/dts/qcom/pmd8028.dtsi | 56 +++++++++++++++++++++++ > arch/arm64/boot/dts/qcom/pmih0108.dtsi | 62 ++++++++++++++++++++++++++ Those two are independent changes. Please use two separate patches. > 2 files changed, 118 insertions(+) > create mode 100644 arch/arm64/boot/dts/qcom/pmd8028.dtsi > create mode 100644 arch/arm64/boot/dts/qcom/pmih0108.dtsi > > diff --git a/arch/arm64/boot/dts/qcom/pmd8028.dtsi b/arch/arm64/boot/dts/qcom/pmd8028.dtsi > new file mode 100644 > index 000000000000..f8ef8e133854 > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/pmd8028.dtsi > @@ -0,0 +1,56 @@ > +// SPDX-License-Identifier: BSD-3-Clause > +/* > + * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved. > + */ > + > +#include <dt-bindings/interrupt-controller/irq.h> > +#include <dt-bindings/spmi/spmi.h> > + > +/ { > + thermal-zones { > + pmd8028-thermal { > + polling-delay-passive = <100>; > + thermal-sensors = <&pmd8028_temp_alarm>; > + > + trips { > + pmd8028_trip0: trip0 { > + temperature = <95000>; > + hysteresis = <0>; > + type = "passive"; > + }; > + > + pmd8028_trip1: trip1 { > + temperature = <115000>; > + hysteresis = <0>; > + type = "hot"; "critical" ? > + }; > + }; > + }; > + }; > +}; > + > +&spmi_bus { > + pmd8028: pmic@4 { > + compatible = "qcom,pmd8028", "qcom,spmi-pmic"; > + reg = <0x4 SPMI_USID>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + pmd8028_temp_alarm: temp-alarm@a00 { > + compatible = "qcom,spmi-temp-alarm"; > + reg = <0xa00>; > + interrupts = <0x4 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; > + #thermal-sensor-cells = <0>; > + }; > + > + pmd8028_gpios: gpio@8800 { > + compatible = "qcom,pmd8028-gpio", "qcom,spmi-gpio"; > + reg = <0x8800>; > + gpio-controller; > + gpio-ranges = <&pmd8028_gpios 0 0 4>; > + #gpio-cells = <2>; > + interrupt-controller; > + #interrupt-cells = <2>; > + }; > + }; > +}; > diff --git a/arch/arm64/boot/dts/qcom/pmih0108.dtsi b/arch/arm64/boot/dts/qcom/pmih0108.dtsi > new file mode 100644 > index 000000000000..3907d8fbcf78 > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/pmih0108.dtsi > @@ -0,0 +1,62 @@ > +// SPDX-License-Identifier: BSD-3-Clause > +/* > + * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved. > + */ > + > +#include <dt-bindings/interrupt-controller/irq.h> > +#include <dt-bindings/spmi/spmi.h> > + > +/ { > + thermal-zones { > + pmih0108-thermal { > + polling-delay-passive = <100>; > + thermal-sensors = <&pmih0108_temp_alarm>; > + > + trips { > + trip0 { > + temperature = <95000>; > + hysteresis = <0>; > + type = "passive"; > + }; > + > + trip1 { > + temperature = <115000>; > + hysteresis = <0>; > + type = "hot"; "critical" ? > + }; > + }; > + }; > + }; > +}; > + > +&spmi_bus { > + pmih0108: pmic@7 { > + compatible = "qcom,pmih0108", "qcom,spmi-pmic"; > + reg = <0x7 SPMI_USID>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + pmih0108_temp_alarm: temp-alarm@a00 { > + compatible = "qcom,spmi-temp-alarm"; > + reg = <0xa00>; > + interrupts = <0x7 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; > + #thermal-sensor-cells = <0>; > + }; > + > + pmih0108_gpios: gpio@8800 { > + compatible = "qcom,pmih0108-gpio", "qcom,spmi-gpio"; > + reg = <0x8800>; > + gpio-controller; > + gpio-ranges = <&pmih0108_gpios 0 0 18>; > + #gpio-cells = <2>; > + interrupt-controller; > + #interrupt-cells = <2>; > + }; > + > + pmih0108_eusb2_repeater: phy@fd00 { > + compatible = "qcom,pm8550b-eusb2-repeater"; > + reg = <0xfd00>; > + #phy-cells = <0>; > + }; > + }; > +}; > -- > 2.46.1 > -- With best wishes Dmitry ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v2 2/6] arm64: dts: qcom: Add pmd8028 and pmih0108 PMICs 2024-11-15 14:58 ` Dmitry Baryshkov @ 2024-11-18 22:16 ` Melody Olvera 0 siblings, 0 replies; 12+ messages in thread From: Melody Olvera @ 2024-11-18 22:16 UTC (permalink / raw) To: Dmitry Baryshkov Cc: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Catalin Marinas, Will Deacon, Geert Uytterhoeven, Neil Armstrong, Arnd Bergmann, Nícolas F . R . A . Prado, Trilok Soni, Satya Durga Srinivasu Prabhala, linux-arm-msm, devicetree, linux-kernel, linux-arm-kernel, Jishnu Prakash On 11/15/2024 6:58 AM, Dmitry Baryshkov wrote: > On Mon, Nov 11, 2024 at 04:49:32PM -0800, Melody Olvera wrote: >> From: Jishnu Prakash <quic_jprakash@quicinc.com> >> >> Add descriptions of pmd8028 and pmih0108 PMICs used on SM8750 >> platforms. > Up/lower case? Up; will change. > >> Signed-off-by: Jishnu Prakash <quic_jprakash@quicinc.com> >> Signed-off-by: Melody Olvera <quic_molvera@quicinc.com> >> --- >> arch/arm64/boot/dts/qcom/pmd8028.dtsi | 56 +++++++++++++++++++++++ >> arch/arm64/boot/dts/qcom/pmih0108.dtsi | 62 ++++++++++++++++++++++++++ > Those two are independent changes. Please use two separate patches. Sure thing. Will split. > >> 2 files changed, 118 insertions(+) >> create mode 100644 arch/arm64/boot/dts/qcom/pmd8028.dtsi >> create mode 100644 arch/arm64/boot/dts/qcom/pmih0108.dtsi >> >> diff --git a/arch/arm64/boot/dts/qcom/pmd8028.dtsi b/arch/arm64/boot/dts/qcom/pmd8028.dtsi >> new file mode 100644 >> index 000000000000..f8ef8e133854 >> --- /dev/null >> +++ b/arch/arm64/boot/dts/qcom/pmd8028.dtsi >> @@ -0,0 +1,56 @@ >> +// SPDX-License-Identifier: BSD-3-Clause >> +/* >> + * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved. >> + */ >> + >> +#include <dt-bindings/interrupt-controller/irq.h> >> +#include <dt-bindings/spmi/spmi.h> >> + >> +/ { >> + thermal-zones { >> + pmd8028-thermal { >> + polling-delay-passive = <100>; >> + thermal-sensors = <&pmd8028_temp_alarm>; >> + >> + trips { >> + pmd8028_trip0: trip0 { >> + temperature = <95000>; >> + hysteresis = <0>; >> + type = "passive"; >> + }; >> + >> + pmd8028_trip1: trip1 { >> + temperature = <115000>; >> + hysteresis = <0>; >> + type = "hot"; > "critical" ? Will add. > >> + }; >> + }; >> + }; >> + }; >> +}; >> + >> +&spmi_bus { >> + pmd8028: pmic@4 { >> + compatible = "qcom,pmd8028", "qcom,spmi-pmic"; >> + reg = <0x4 SPMI_USID>; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + pmd8028_temp_alarm: temp-alarm@a00 { >> + compatible = "qcom,spmi-temp-alarm"; >> + reg = <0xa00>; >> + interrupts = <0x4 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; >> + #thermal-sensor-cells = <0>; >> + }; >> + >> + pmd8028_gpios: gpio@8800 { >> + compatible = "qcom,pmd8028-gpio", "qcom,spmi-gpio"; >> + reg = <0x8800>; >> + gpio-controller; >> + gpio-ranges = <&pmd8028_gpios 0 0 4>; >> + #gpio-cells = <2>; >> + interrupt-controller; >> + #interrupt-cells = <2>; >> + }; >> + }; >> +}; >> diff --git a/arch/arm64/boot/dts/qcom/pmih0108.dtsi b/arch/arm64/boot/dts/qcom/pmih0108.dtsi >> new file mode 100644 >> index 000000000000..3907d8fbcf78 >> --- /dev/null >> +++ b/arch/arm64/boot/dts/qcom/pmih0108.dtsi >> @@ -0,0 +1,62 @@ >> +// SPDX-License-Identifier: BSD-3-Clause >> +/* >> + * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved. >> + */ >> + >> +#include <dt-bindings/interrupt-controller/irq.h> >> +#include <dt-bindings/spmi/spmi.h> >> + >> +/ { >> + thermal-zones { >> + pmih0108-thermal { >> + polling-delay-passive = <100>; >> + thermal-sensors = <&pmih0108_temp_alarm>; >> + >> + trips { >> + trip0 { >> + temperature = <95000>; >> + hysteresis = <0>; >> + type = "passive"; >> + }; >> + >> + trip1 { >> + temperature = <115000>; >> + hysteresis = <0>; >> + type = "hot"; > "critical" ? Will add. Thanks, Melody > >> + }; >> + }; >> + }; >> + }; >> +}; >> +[...] ^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v2 3/6] arm64: dts: qcom: Add base SM8750 dtsi 2024-11-12 0:49 [PATCH v2 0/6] dts: qcom: Introduce SM8750 device trees Melody Olvera 2024-11-12 0:49 ` [PATCH v2 1/6] dt-bindings: arm: qcom: Document sm8750 SoC and boards Melody Olvera 2024-11-12 0:49 ` [PATCH v2 2/6] arm64: dts: qcom: Add pmd8028 and pmih0108 PMICs Melody Olvera @ 2024-11-12 0:49 ` Melody Olvera 2024-11-15 20:26 ` Konrad Dybcio 2024-11-12 0:49 ` [PATCH v2 4/6] arm64: dts: qcom: sm8750: Add pmic dtsi Melody Olvera ` (2 subsequent siblings) 5 siblings, 1 reply; 12+ messages in thread From: Melody Olvera @ 2024-11-12 0:49 UTC (permalink / raw) To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Catalin Marinas, Will Deacon, Geert Uytterhoeven, Dmitry Baryshkov, Neil Armstrong, Arnd Bergmann, Nícolas F . R . A . Prado, Trilok Soni, Satya Durga Srinivasu Prabhala Cc: linux-arm-msm, devicetree, linux-kernel, linux-arm-kernel, Melody Olvera, Taniya Das, Jishnu Prakash, Raviteja Laggyshetty Add the base dtsi for the SM8750 SoC describing the CPUs, GCC and RPMHCC clock controllers, geni UART, interrupt controller, TLMM, reserved memory, interconnects, and SMMU. Co-developed-by: Taniya Das <quic_tdas@quicinc.com> Signed-off-by: Taniya Das <quic_tdas@quicinc.com> Co-developed-by: Jishnu Prakash <quic_jprakash@quicinc.com> Signed-off-by: Jishnu Prakash <quic_jprakash@quicinc.com> Co-developed-by: Raviteja Laggyshetty <quic_rlaggysh@quicinc.com> Signed-off-by: Raviteja Laggyshetty <quic_rlaggysh@quicinc.com> Signed-off-by: Melody Olvera <quic_molvera@quicinc.com> --- arch/arm64/boot/dts/qcom/sm8750.dtsi | 2917 ++++++++++++++++++++++++++ 1 file changed, 2917 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sm8750.dtsi diff --git a/arch/arm64/boot/dts/qcom/sm8750.dtsi b/arch/arm64/boot/dts/qcom/sm8750.dtsi new file mode 100644 index 000000000000..b63112e5130b --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sm8750.dtsi @@ -0,0 +1,2917 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved. + */ + +#include <dt-bindings/clock/qcom,rpmh.h> +#include <dt-bindings/clock/qcom,sm8750-gcc.h> +#include <dt-bindings/clock/qcom,sm8750-tcsr.h> +#include <dt-bindings/dma/qcom-gpi.h> +#include <dt-bindings/interconnect/qcom,icc.h> +#include <dt-bindings/interconnect/qcom,sm8750-rpmh.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/power/qcom,rpmhpd.h> +#include <dt-bindings/power/qcom-rpmpd.h> +#include <dt-bindings/soc/qcom,rpmh-rsc.h> + +/ { + interrupt-parent = <&intc>; + + #address-cells = <2>; + #size-cells = <2>; + + cpus { + #address-cells = <2>; + #size-cells = <0>; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "qcom,oryon"; + reg = <0x0 0x0>; + enable-method = "psci"; + next-level-cache = <&l2_0>; + power-domains = <&cpu_pd0>; + power-domain-names = "psci"; + cpu-idle-states = <&cluster0_c4>; + + l2_0: l2-cache { + compatible = "cache"; + cache-level = <2>; + cache-unified; + }; + }; + + cpu1: cpu@100 { + device_type = "cpu"; + compatible = "qcom,oryon"; + reg = <0x0 0x100>; + enable-method = "psci"; + next-level-cache = <&l2_0>; + power-domains = <&cpu_pd1>; + power-domain-names = "psci"; + cpu-idle-states = <&cluster0_c4>; + }; + + cpu2: cpu@200 { + device_type = "cpu"; + compatible = "qcom,oryon"; + reg = <0x0 0x200>; + enable-method = "psci"; + next-level-cache = <&l2_0>; + power-domains = <&cpu_pd2>; + power-domain-names = "psci"; + cpu-idle-states = <&cluster0_c4>; + }; + + cpu3: cpu@300 { + device_type = "cpu"; + compatible = "qcom,oryon"; + reg = <0x0 0x300>; + enable-method = "psci"; + next-level-cache = <&l2_0>; + power-domains = <&cpu_pd3>; + power-domain-names = "psci"; + cpu-idle-states = <&cluster0_c4>; + }; + + cpu4: cpu@400 { + device_type = "cpu"; + compatible = "qcom,oryon"; + reg = <0x0 0x400>; + enable-method = "psci"; + next-level-cache = <&l2_0>; + power-domains = <&cpu_pd4>; + power-domain-names = "psci"; + cpu-idle-states = <&cluster0_c4>; + }; + + cpu5: cpu@500 { + device_type = "cpu"; + compatible = "qcom,oryon"; + reg = <0x0 0x500>; + enable-method = "psci"; + next-level-cache = <&l2_0>; + power-domains = <&cpu_pd5>; + power-domain-names = "psci"; + cpu-idle-states = <&cluster0_c4>; + }; + + cpu6: cpu@10000 { + device_type = "cpu"; + compatible = "qcom,oryon"; + reg = <0x0 0x10000>; + enable-method = "psci"; + next-level-cache = <&L2_1>; + power-domains = <&cpu_pd6>; + power-domain-names = "psci"; + cpu-idle-states = <&cluster1_c4>; + + L2_1: l2-cache { + compatible = "cache"; + cache-level = <2>; + cache-unified; + }; + }; + + cpu7: cpu@10100 { + device_type = "cpu"; + compatible = "qcom,oryon"; + reg = <0x0 0x10100>; + enable-method = "psci"; + next-level-cache = <&L2_1>; + power-domains = <&cpu_pd7>; + power-domain-names = "psci"; + cpu-idle-states = <&cluster1_c4>; + }; + + cpu-map { + cluster0 { + core0 { + cpu = <&cpu0>; + }; + + core1 { + cpu = <&cpu1>; + }; + + core2 { + cpu = <&cpu2>; + }; + + core3 { + cpu = <&cpu3>; + }; + + core4 { + cpu = <&cpu4>; + }; + + core5 { + cpu = <&cpu5>; + }; + }; + + cluster1 { + core0 { + cpu = <&cpu6>; + }; + + core1 { + cpu = <&cpu7>; + }; + }; + }; + + idle-states { + entry-method = "psci"; + + cluster0_c4: cpu-sleep-0 { + compatible = "arm,idle-state"; + idle-state-name = "ret"; + arm,psci-suspend-param = <0x00000004>; + entry-latency-us = <93>; + exit-latency-us = <129>; + min-residency-us = <560>; + }; + + cluster1_c4: cpu-sleep-1 { + compatible = "arm,idle-state"; + idle-state-name = "ret"; + arm,psci-suspend-param = <0x00000004>; + entry-latency-us = <172>; + exit-latency-us = <130>; + min-residency-us = <686>; + }; + + }; + + domain-idle-states { + cluster_cl5: cluster-sleep-0 { + compatible = "domain-idle-state"; + arm,psci-suspend-param = <0x01000054>; + entry-latency-us = <2150>; + exit-latency-us = <1983>; + min-residency-us = <9144>; + }; + + domain_ss3: domain-sleep-0 { + compatible = "domain-idle-state"; + arm,psci-suspend-param = <0x0200c354>; + entry-latency-us = <2800>; + exit-latency-us = <4400>; + min-residency-us = <10150>; + }; + }; + }; + + firmware { + scm: scm { + compatible = "qcom,scm-sm8750", "qcom,scm"; + interconnects = <&aggre2_noc MASTER_CRYPTO QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + }; + }; + + clk_virt: interconnect-0 { + compatible = "qcom,sm8750-clk-virt"; + #interconnect-cells = <2>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + mc_virt: interconnect-1 { + compatible = "qcom,sm8750-mc-virt"; + #interconnect-cells = <2>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + memory@a0000000 { + device_type = "memory"; + /* We expect the bootloader to fill in the size */ + reg = <0x0 0xa0000000 0x0 0x0>; + }; + + pmu { + compatible = "arm,armv8-pmuv3"; + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_LOW>; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + + cpu_pd0: power-domain-cpu0 { + #power-domain-cells = <0>; + power-domains = <&cluster_pd0>; + }; + + cpu_pd1: power-domain-cpu1 { + #power-domain-cells = <0>; + power-domains = <&cluster_pd0>; + }; + + cpu_pd2: power-domain-cpu2 { + #power-domain-cells = <0>; + power-domains = <&cluster_pd0>; + }; + + cpu_pd3: power-domain-cpu3 { + #power-domain-cells = <0>; + power-domains = <&cluster_pd0>; + }; + + cpu_pd4: power-domain-cpu4 { + #power-domain-cells = <0>; + power-domains = <&cluster_pd0>; + }; + + cpu_pd5: power-domain-cpu5 { + #power-domain-cells = <0>; + power-domains = <&cluster_pd0>; + }; + + cpu_pd6: power-domain-cpu6 { + #power-domain-cells = <0>; + power-domains = <&cluster_pd1>; + }; + + cpu_pd7: power-domain-cpu7 { + #power-domain-cells = <0>; + power-domains = <&cluster_pd1>; + }; + + cluster_pd0: power-domain-cpu-cluster0 { + #power-domain-cells = <0>; + domain-idle-states = <&cluster_cl5>; + power-domains = <&system_pd>; + }; + + cluster_pd1: power-domain-cpu-cluster1 { + #power-domain-cells = <0>; + domain-idle-states = <&cluster_cl5>; + power-domains = <&system_pd>; + }; + + system_pd: power-domain-system { + #power-domain-cells = <0>; + domain-idle-states = <&domain_ss3>; + }; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + gunyah_hyp_mem: gunyah-hyp@80000000 { + reg = <0x0 0x80000000 0x0 0xe00000>; + no-map; + }; + + cpusys_vm_mem: cpusys-vm-mem@80e00000 { + reg = <0x0 0x80e00000 0x0 0x40000>; + no-map; + }; + + cpucp_mem: cpucp@81200000 { + reg = <0x0 0x81200000 0x0 0x200000>; + no-map; + }; + + xbl_dtlog_mem: xbl-dtlog@81a00000 { + reg = <0x0 0x81a00000 0x0 0x40000>; + no-map; + }; + + aop_image_mem: aop-image@81c00000 { + reg = <0x0 0x81c00000 0x0 0x60000>; + no-map; + }; + + aop_cmd_db_mem: aop-cmd-db@81c60000 { + compatible = "qcom,cmd-db"; + reg = <0x0 0x81c60000 0x0 0x20000>; + no-map; + }; + + /* Merged aop_config, tme_crash_dump, tme_log and uefi_log regions */ + aop_tme_uefi_merged_mem: aop-tme-uefi-merged@81c80000 { + reg = <0x0 0x81c80000 0x0 0x74000>; + no-map; + }; + + /* Secdata region can be reused by apps */ + + smem_mem: smem@81d00000 { + compatible = "qcom,smem"; + reg = <0x0 0x81d00000 0x0 0x200000>; + hwlocks = <&tcsr_mutex 3>; + no-map; + }; + + pdp_ns_shared_mem: pdp-ns-shared@81f00000 { + reg = <0x0 0x81f00000 0x0 0x100000>; + no-map; + }; + + cpucp_scandump_mem: cpucp-scandump@82000000 { + reg = <0x0 0x82000000 0x0 0x380000>; + no-map; + }; + + adsp_mhi_mem: adsp-mhi@82380000 { + reg = <0x0 0x82380000 0x0 0x20000>; + no-map; + }; + + soccp_sdi_mem: soccp-sdi@823a0000 { + reg = <0x0 0x823a0000 0x0 0x40000>; + no-map; + }; + + pmic_minii_dump_mem: pmic-minii-dump@823e0000 { + reg = <0x0 0x823e0000 0x0 0x80000>; + no-map; + }; + + pvmfw_mem: pvmfw@824a0000 { + reg = <0x0 0x824a0000 0x0 0x100000>; + no-map; + }; + + global_sync_mem: global-sync@82600000 { + reg = <0x0 0x82600000 0x0 0x100000>; + no-map; + }; + + tz_stat_mem: tz-stat@82700000 { + reg = <0x0 0x82700000 0x0 0x100000>; + no-map; + }; + + qdss_mem: qdss@82800000 { + reg = <0x0 0x82800000 0x0 0x2000000>; + no-map; + }; + + dsm_partition_1_mem: dsm-partition-1@84a00000 { + reg = <0x0 0x84a00000 0x0 0x4900000>; + no-map; + }; + + dsm_partition_2_mem: dsm-partition-2@89300000 { + reg = <0x0 0x89300000 0x0 0xa80000>; + no-map; + }; + + mpss_mem: mpss@8ba00000 { + reg = <0x0 0x8ba00000 0x0 0xf600000>; + no-map; + }; + + q6_mpss_dtb_mem: q6-mpss-dtb@9b000000 { + reg = <0x0 0x9b000000 0x0 0x80000>; + no-map; + }; + + ipa_fw_mem: ipa-fw@9b080000 { + reg = <0x0 0x9b080000 0x0 0x10000>; + no-map; + }; + + ipa_gsi_mem: ipa-gsi@9b090000 { + reg = <0x0 0x9b090000 0x0 0xa000>; + no-map; + }; + + gpu_micro_code_mem: gpu-micro-code@9b09a000 { + reg = <0x0 0x9b09a000 0x0 0x2000>; + no-map; + }; + + spss_region_mem: spss@9b0a0000 { + reg = <0x0 0x9b0a0000 0x0 0x1e0000>; + no-map; + }; + + /* First part of the "SPU secure shared memory" region */ + spu_tz_shared_mem: spu-tz-shared@9b280000 { + reg = <0x0 0x9b280000 0x0 0x40000>; + no-map; + }; + + /* Second part of the "SPU secure shared memory" region */ + spu_modem_shared_mem: spu-modem-shared@9b2c0000 { + reg = <0x0 0x9b2c0000 0x0 0x40000>; + no-map; + }; + + camera_mem: camera@9b300000 { + reg = <0x0 0x9b300000 0x0 0x800000>; + no-map; + }; + + camera_2_mem: camera-2@9bb00000 { + reg = <0x0 0x9bb00000 0x0 0x800000>; + no-map; + }; + + video_mem: video@9c300000 { + reg = <0x0 0x9c300000 0x0 0x800000>; + no-map; + }; + + cvp_mem: cvp@9cb00000 { + reg = <0x0 0x9cb00000 0x0 0x700000>; + no-map; + }; + + cdsp_mem: cdsp@9d200000 { + reg = <0x0 0x9d200000 0x0 0x1900000>; + no-map; + }; + + q6_cdsp_dtb_mem: q6-cdsp-dtb@9eb00000 { + reg = <0x0 0x9eb00000 0x0 0x80000>; + no-map; + }; + + soccp_mem: soccp@9ec00000 { + reg = <0x0 0x9ec00000 0x0 0x180000>; + no-map; + }; + + q6_adsp_dtb_mem: q6-adsp-dtb@9ed80000 { + reg = <0x0 0x9ed80000 0x0 0x80000>; + no-map; + }; + + adspslpi_mem: adspslpi@9ee00000 { + reg = <0x0 0x9ee00000 0x0 0x3a80000>; + no-map; + }; + + xbl_ramdump_mem: xbl-ramdump@b8000000 { + reg = <0x0 0xb8000000 0x0 0x1c0000>; + no-map; + }; + + hwfence_shbuf: hwfence-shbuf@d4e23000 { + no-map; + reg = <0x0 0xd4e23000 0x0 0x2dd000>; + }; + + /* Merged tz_reserved, xbl_sc, and qtee regions */ + tz_merged_mem: tz-merged@d8000000 { + reg = <0x0 0xd8000000 0x0 0x600000>; + no-map; + }; + + trust_ui_vm_mem: trust-ui-vm@f3800000 { + reg = <0x0 0xf3800000 0x0 0x4400000>; + no-map; + }; + + oem_vm_mem: oem-vm@f7c00000 { + reg = <0x0 0xf7c00000 0x0 0x4c00000>; + no-map; + }; + + llcc_lpi_mem: llcc-lpi@ff800000 { + reg = <0x0 0xff800000 0x0 0x800000>; + no-map; + }; + }; + + soc: soc@0 { + compatible = "simple-bus"; + + #address-cells = <2>; + #size-cells = <2>; + dma-ranges = <0 0 0 0 0x10 0>; + ranges = <0 0 0 0 0x10 0>; + + gcc: clock-controller@100000 { + compatible = "qcom,sm8750-gcc"; + reg = <0x0 0x00100000 0x0 0x1f4200>; + + clocks = <&bi_tcxo_div2>, + <&sleep_clk>, + <0>, + <0>, + <0>, + <0>, + <0>, + <0>, + <0>, + <0>; + + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + }; + + gpi_dma2: dma-controller@800000 { + compatible = "qcom,sm8750-gpi-dma", "qcom,sm6350-gpi-dma"; + reg = <0x0 0x00800000 0x0 0x60000>; + + interrupts = <GIC_SPI 588 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 589 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 590 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 591 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 592 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 593 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 594 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 595 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 596 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 597 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 598 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 599 IRQ_TYPE_LEVEL_HIGH>; + + dma-channels = <12>; + dma-channel-mask = <0x1e>; + #dma-cells = <3>; + + iommus = <&apps_smmu 0x436 0x0>; + + status = "disabled"; + }; + + qupv3_2: geniqup@8c0000 { + compatible = "qcom,geni-se-qup"; + reg = <0x0 0x008c0000 0x0 0x2000>; + + clocks = <&gcc GCC_QUPV3_WRAP_2_M_AHB_CLK>, + <&gcc GCC_QUPV3_WRAP_2_S_AHB_CLK>; + clock-names = "m-ahb", + "s-ahb"; + + iommus = <&apps_smmu 0x423 0x0>; + + #address-cells = <2>; + #size-cells = <2>; + ranges; + + status = "disabled"; + + i2c8: i2c@880000 { + compatible = "qcom,geni-i2c"; + reg = <0x0 0x00880000 0x0 0x4000>; + + interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>; + clock-names = "se"; + + interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>, + <&aggre2_noc MASTER_QUP_2 QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config", + "qup-memory"; + + dmas = <&gpi_dma2 0 0 QCOM_GPI_I2C>, + <&gpi_dma2 1 0 QCOM_GPI_I2C>; + dma-names = "tx", + "rx"; + + pinctrl-0 = <&qup_i2c8_data_clk>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + spi8: spi@880000 { + compatible = "qcom,geni-spi"; + reg = <0x0 0x00880000 0x0 0x4000>; + + interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>; + clock-names = "se"; + + interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>, + <&aggre2_noc MASTER_QUP_2 QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config", + "qup-memory"; + + dmas = <&gpi_dma2 0 0 QCOM_GPI_SPI>, + <&gpi_dma2 1 0 QCOM_GPI_SPI>; + dma-names = "tx", + "rx"; + + pinctrl-0 = <&qup_spi8_data_clk>, <&qup_spi8_cs>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + i2c9: i2c@884000 { + compatible = "qcom,geni-i2c"; + reg = <0x0 0x00884000 0x0 0x4000>; + + interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>; + clock-names = "se"; + + interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>, + <&aggre2_noc MASTER_QUP_2 QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config", + "qup-memory"; + + dmas = <&gpi_dma2 0 1 QCOM_GPI_I2C>, + <&gpi_dma2 1 1 QCOM_GPI_I2C>; + dma-names = "tx", + "rx"; + + pinctrl-0 = <&qup_i2c9_data_clk>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + spi9: spi@884000 { + compatible = "qcom,geni-spi"; + reg = <0x0 0x00884000 0x0 0x4000>; + + interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>; + clock-names = "se"; + + interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>, + <&aggre2_noc MASTER_QUP_2 QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config", + "qup-memory"; + + dmas = <&gpi_dma2 0 1 QCOM_GPI_SPI>, + <&gpi_dma2 1 1 QCOM_GPI_SPI>; + dma-names = "tx", + "rx"; + + pinctrl-0 = <&qup_spi9_data_clk>, <&qup_spi9_cs>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + i2c10: i2c@888000 { + compatible = "qcom,geni-i2c"; + reg = <0x0 0x00888000 0x0 0x4000>; + + interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>; + clock-names = "se"; + + interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>, + <&aggre2_noc MASTER_QUP_2 QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config", + "qup-memory"; + + dmas = <&gpi_dma2 0 2 QCOM_GPI_I2C>, + <&gpi_dma2 1 2 QCOM_GPI_I2C>; + dma-names = "tx", + "rx"; + + pinctrl-0 = <&qup_i2c10_data_clk>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + spi10: spi@888000 { + compatible = "qcom,geni-spi"; + reg = <0x0 0x00888000 0x0 0x4000>; + + interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>; + clock-names = "se"; + + interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>, + <&aggre2_noc MASTER_QUP_2 QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config", + "qup-memory"; + + dmas = <&gpi_dma2 0 2 QCOM_GPI_SPI>, + <&gpi_dma2 1 2 QCOM_GPI_SPI>; + dma-names = "tx", + "rx"; + + pinctrl-0 = <&qup_spi10_data_clk>, <&qup_spi10_cs>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + i2c11: i2c@88c000 { + compatible = "qcom,geni-i2c"; + reg = <0x0 0x0088c000 0x0 0x4000>; + + interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>; + clock-names = "se"; + + interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>, + <&aggre2_noc MASTER_QUP_2 QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config", + "qup-memory"; + + dmas = <&gpi_dma2 0 3 QCOM_GPI_I2C>, + <&gpi_dma2 1 3 QCOM_GPI_I2C>; + dma-names = "tx", + "rx"; + + pinctrl-0 = <&qup_i2c11_data_clk>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + spi11: spi@88c000 { + compatible = "qcom,geni-spi"; + reg = <0x0 0x0088c000 0x0 0x4000>; + + interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>; + clock-names = "se"; + + interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>, + <&aggre2_noc MASTER_QUP_2 QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config", + "qup-memory"; + + dmas = <&gpi_dma2 0 3 QCOM_GPI_SPI>, + <&gpi_dma2 1 3 QCOM_GPI_SPI>; + dma-names = "tx", + "rx"; + + pinctrl-0 = <&qup_spi11_data_clk>, <&qup_spi11_cs>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + i2c12: i2c@890000 { + compatible = "qcom,geni-i2c"; + reg = <0x0 0x00890000 0x0 0x4000>; + + interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>; + clock-names = "se"; + + interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>, + <&aggre2_noc MASTER_QUP_2 QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config", + "qup-memory"; + + dmas = <&gpi_dma2 0 4 QCOM_GPI_I2C>, + <&gpi_dma2 1 4 QCOM_GPI_I2C>; + dma-names = "tx", + "rx"; + + pinctrl-0 = <&qup_i2c12_data_clk>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + spi12: spi@890000 { + compatible = "qcom,geni-spi"; + reg = <0x0 0x00890000 0x0 0x4000>; + + interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>; + clock-names = "se"; + + interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>, + <&aggre2_noc MASTER_QUP_2 QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config", + "qup-memory"; + + dmas = <&gpi_dma2 0 4 QCOM_GPI_SPI>, + <&gpi_dma2 1 4 QCOM_GPI_SPI>; + dma-names = "tx", + "rx"; + + pinctrl-0 = <&qup_spi12_data_clk>, <&qup_spi12_cs>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + i2c13: i2c@894000 { + compatible = "qcom,geni-i2c"; + reg = <0x0 0x00894000 0x0 0x4000>; + + interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>; + clock-names = "se"; + + interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>, + <&aggre2_noc MASTER_QUP_2 QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config", + "qup-memory"; + + dmas = <&gpi_dma2 0 5 QCOM_GPI_I2C>, + <&gpi_dma2 1 5 QCOM_GPI_I2C>; + dma-names = "tx", + "rx"; + + pinctrl-0 = <&qup_i2c13_data_clk>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + spi13: spi@894000 { + compatible = "qcom,geni-spi"; + reg = <0x0 0x00894000 0x0 0x4000>; + + interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>; + clock-names = "se"; + + interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>, + <&aggre2_noc MASTER_QUP_2 QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config", + "qup-memory"; + + dmas = <&gpi_dma2 0 5 QCOM_GPI_SPI>, + <&gpi_dma2 1 5 QCOM_GPI_SPI>; + dma-names = "tx", + "rx"; + + pinctrl-0 = <&qup_spi13_data_clk>, <&qup_spi13_cs>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + uart14: serial@898000 { + compatible = "qcom,geni-uart"; + reg = <0x0 0x00898000 0x0 0x4000>; + + interrupts = <GIC_SPI 461 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>; + clock-names = "se"; + + interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config"; + + pinctrl-0 = <&qup_uart14_default>; + pinctrl-names = "default"; + + status = "disabled"; + }; + + i2c15: i2c@89c000 { + compatible = "qcom,geni-i2c"; + reg = <0x0 0x0089c000 0x0 0x4000>; + + interrupts = <GIC_SPI 462 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_WRAP2_S7_CLK>; + clock-names = "se"; + + interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>, + <&aggre2_noc MASTER_QUP_2 QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config", + "qup-memory"; + + dmas = <&gpi_dma2 0 7 QCOM_GPI_I2C>, + <&gpi_dma2 1 7 QCOM_GPI_I2C>; + dma-names = "tx", + "rx"; + + pinctrl-0 = <&qup_i2c15_data_clk>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + spi15: spi@89c000 { + compatible = "qcom,geni-spi"; + reg = <0x0 0x0089c000 0x0 0x4000>; + + interrupts = <GIC_SPI 462 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_WRAP2_S7_CLK>; + clock-names = "se"; + + interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>, + <&aggre2_noc MASTER_QUP_2 QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config", + "qup-memory"; + + dmas = <&gpi_dma2 0 7 QCOM_GPI_SPI>, + <&gpi_dma2 1 7 QCOM_GPI_SPI>; + dma-names = "tx", + "rx"; + + pinctrl-0 = <&qup_spi15_data_clk>, <&qup_spi15_cs>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + }; + + i2c_master_hub_0: geniqup@9c0000 { + compatible = "qcom,geni-se-i2c-master-hub"; + reg = <0x0 0x009c0000 0x0 0x2000>; + + clocks = <&gcc GCC_QUPV3_I2C_S_AHB_CLK>; + clock-names = "s-ahb"; + + #address-cells = <2>; + #size-cells = <2>; + ranges; + + status = "disabled"; + + i2c_hub_0: i2c@980000 { + compatible = "qcom,geni-i2c-master-hub"; + reg = <0x0 0x00980000 0x0 0x4000>; + + interrupts = <GIC_SPI 464 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_I2C_S0_CLK>, + <&gcc GCC_QUPV3_I2C_CORE_CLK>; + clock-names = "se", + "core"; + + interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_I2C QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config"; + + pinctrl-0 = <&hub_i2c0_data_clk>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + i2c_hub_1: i2c@984000 { + compatible = "qcom,geni-i2c-master-hub"; + reg = <0x0 0x00984000 0x0 0x4000>; + + interrupts = <GIC_SPI 465 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_I2C_S1_CLK>, + <&gcc GCC_QUPV3_I2C_CORE_CLK>; + clock-names = "se", + "core"; + + interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_I2C QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config"; + + pinctrl-0 = <&hub_i2c1_data_clk>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + i2c_hub_2: i2c@988000 { + compatible = "qcom,geni-i2c-master-hub"; + reg = <0x0 0x00988000 0x0 0x4000>; + + interrupts = <GIC_SPI 466 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_I2C_S2_CLK>, + <&gcc GCC_QUPV3_I2C_CORE_CLK>; + clock-names = "se", + "core"; + + interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_I2C QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config"; + + pinctrl-0 = <&hub_i2c2_data_clk>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + i2c_hub_3: i2c@98c000 { + compatible = "qcom,geni-i2c-master-hub"; + reg = <0x0 0x0098c000 0x0 0x4000>; + + interrupts = <GIC_SPI 467 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_I2C_S3_CLK>, + <&gcc GCC_QUPV3_I2C_CORE_CLK>; + clock-names = "se", + "core"; + + interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_I2C QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config"; + + pinctrl-0 = <&hub_i2c3_data_clk>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + i2c_hub_4: i2c@990000 { + compatible = "qcom,geni-i2c-master-hub"; + reg = <0x0 0x00990000 0x0 0x4000>; + + interrupts = <GIC_SPI 468 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_I2C_S4_CLK>, + <&gcc GCC_QUPV3_I2C_CORE_CLK>; + clock-names = "se", + "core"; + + interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_I2C QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config"; + + pinctrl-0 = <&hub_i2c4_data_clk>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + i2c_hub_5: i2c@994000 { + compatible = "qcom,geni-i2c-master-hub"; + reg = <0x0 0x00994000 0x0 0x4000>; + + interrupts = <GIC_SPI 469 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_I2C_S5_CLK>, + <&gcc GCC_QUPV3_I2C_CORE_CLK>; + clock-names = "se", + "core"; + + interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_I2C QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config"; + + pinctrl-0 = <&hub_i2c5_data_clk>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + i2c_hub_6: i2c@998000 { + compatible = "qcom,geni-i2c-master-hub"; + reg = <0x0 0x00998000 0x0 0x4000>; + + interrupts = <GIC_SPI 470 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_I2C_S6_CLK>, + <&gcc GCC_QUPV3_I2C_CORE_CLK>; + clock-names = "se", + "core"; + + interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_I2C QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config"; + + pinctrl-0 = <&hub_i2c6_data_clk>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + i2c_hub_7: i2c@99c000 { + compatible = "qcom,geni-i2c-master-hub"; + reg = <0x0 0x0099c000 0x0 0x4000>; + + interrupts = <GIC_SPI 471 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_I2C_S7_CLK>, + <&gcc GCC_QUPV3_I2C_CORE_CLK>; + clock-names = "se", + "core"; + + interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_I2C QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config"; + + pinctrl-0 = <&hub_i2c7_data_clk>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + i2c_hub_8: i2c@9a0000 { + compatible = "qcom,geni-i2c-master-hub"; + reg = <0x0 0x009a0000 0x0 0x4000>; + + interrupts = <GIC_SPI 472 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_I2C_S8_CLK>, + <&gcc GCC_QUPV3_I2C_CORE_CLK>; + clock-names = "se", + "core"; + + interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_I2C QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config"; + + pinctrl-0 = <&hub_i2c8_data_clk>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + i2c_hub_9: i2c@9a4000 { + compatible = "qcom,geni-i2c-master-hub"; + reg = <0x0 0x009a4000 0x0 0x4000>; + + interrupts = <GIC_SPI 473 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_I2C_S9_CLK>, + <&gcc GCC_QUPV3_I2C_CORE_CLK>; + clock-names = "se", + "core"; + + interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_I2C QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config"; + + pinctrl-0 = <&hub_i2c9_data_clk>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + }; + + gpi_dma1: dma-controller@a00000 { + compatible = "qcom,sm8750-gpi-dma", "qcom,sm6350-gpi-dma"; + reg = <0x0 0x00a00000 0x0 0x60000>; + + interrupts = <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 294 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>; + + dma-channels = <12>; + dma-channel-mask = <0x1e>; + #dma-cells = <3>; + + iommus = <&apps_smmu 0xb6 0x0>; + + status = "disabled"; + }; + + qupv3_1: geniqup@ac0000 { + compatible = "qcom,geni-se-qup"; + reg = <0x0 0x00ac0000 0x0 0x2000>; + + clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>, + <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>; + clock-names = "m-ahb", + "s-ahb"; + + iommus = <&apps_smmu 0xa3 0x0>; + + #address-cells = <2>; + #size-cells = <2>; + ranges; + + status = "disabled"; + + i2c0: i2c@a80000 { + compatible = "qcom,geni-i2c"; + reg = <0x0 0x00a80000 0x0 0x4000>; + + interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>; + clock-names = "se"; + + interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>, + <&aggre1_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config", + "qup-memory"; + + dmas = <&gpi_dma1 0 0 QCOM_GPI_I2C>, + <&gpi_dma1 1 0 QCOM_GPI_I2C>; + dma-names = "tx", + "rx"; + + pinctrl-0 = <&qup_i2c0_data_clk>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + spi0: spi@a80000 { + compatible = "qcom,geni-spi"; + reg = <0x0 0x00a80000 0x0 0x4000>; + + interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>; + clock-names = "se"; + + interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>, + <&aggre1_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config", + "qup-memory"; + + dmas = <&gpi_dma1 0 0 QCOM_GPI_SPI>, + <&gpi_dma1 1 0 QCOM_GPI_SPI>; + dma-names = "tx", + "rx"; + + pinctrl-0 = <&qup_spi0_data_clk>, <&qup_spi0_cs>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + i2c1: i2c@a84000 { + compatible = "qcom,geni-i2c"; + reg = <0x0 0x00a84000 0x0 0x4000>; + + interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>; + clock-names = "se"; + + interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>, + <&aggre1_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config", + "qup-memory"; + + dmas = <&gpi_dma1 0 1 QCOM_GPI_I2C>, + <&gpi_dma1 1 1 QCOM_GPI_I2C>; + dma-names = "tx", + "rx"; + + pinctrl-0 = <&qup_i2c1_data_clk>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + spi1: spi@a84000 { + compatible = "qcom,geni-spi"; + reg = <0x0 0x00a84000 0x0 0x4000>; + + interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>; + clock-names = "se"; + + interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>, + <&aggre1_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config", + "qup-memory"; + + dmas = <&gpi_dma1 0 1 QCOM_GPI_SPI>, + <&gpi_dma1 1 1 QCOM_GPI_SPI>; + dma-names = "tx", + "rx"; + + pinctrl-0 = <&qup_spi1_data_clk>, <&qup_spi1_cs>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + i2c2: i2c@a88000 { + compatible = "qcom,geni-i2c"; + reg = <0x0 0x00a88000 0x0 0x4000>; + + interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>; + clock-names = "se"; + + interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>, + <&aggre1_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config", + "qup-memory"; + + dmas = <&gpi_dma1 0 2 QCOM_GPI_I2C>, + <&gpi_dma1 1 2 QCOM_GPI_I2C>; + dma-names = "tx", + "rx"; + + pinctrl-0 = <&qup_i2c2_data_clk>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + spi2: spi@a88000 { + compatible = "qcom,geni-spi"; + reg = <0x0 0x00a88000 0x0 0x4000>; + + interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>; + clock-names = "se"; + + interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>, + <&aggre1_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config", + "qup-memory"; + + dmas = <&gpi_dma1 0 2 QCOM_GPI_SPI>, + <&gpi_dma1 1 2 QCOM_GPI_SPI>; + dma-names = "tx", + "rx"; + + pinctrl-0 = <&qup_spi2_data_clk>, <&qup_spi2_cs>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + i2c3: i2c@a8c000 { + compatible = "qcom,geni-i2c"; + reg = <0x0 0x00a8c000 0x0 0x4000>; + + interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>; + clock-names = "se"; + + interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>, + <&aggre1_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config", + "qup-memory"; + + dmas = <&gpi_dma1 0 3 QCOM_GPI_I2C>, + <&gpi_dma1 1 3 QCOM_GPI_I2C>; + dma-names = "tx", + "rx"; + + pinctrl-0 = <&qup_i2c3_data_clk>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + spi3: spi@a8c000 { + compatible = "qcom,geni-spi"; + reg = <0x0 0x00a8c000 0x0 0x4000>; + + interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>; + clock-names = "se"; + + interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>, + <&aggre1_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config", + "qup-memory"; + + dmas = <&gpi_dma1 0 3 QCOM_GPI_SPI>, + <&gpi_dma1 1 3 QCOM_GPI_SPI>; + dma-names = "tx", + "rx"; + + pinctrl-0 = <&qup_spi3_data_clk>, <&qup_spi3_cs>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + i2c4: i2c@a90000 { + compatible = "qcom,geni-i2c"; + reg = <0x0 0x00a90000 0x0 0x4000>; + + interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>; + clock-names = "se"; + + interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>, + <&aggre1_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config", + "qup-memory"; + + dmas = <&gpi_dma1 0 4 QCOM_GPI_I2C>, + <&gpi_dma1 1 4 QCOM_GPI_I2C>; + dma-names = "tx", + "rx"; + + pinctrl-0 = <&qup_i2c4_data_clk>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + spi4: spi@a90000 { + compatible = "qcom,geni-spi"; + reg = <0x0 0x00a90000 0x0 0x4000>; + + interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>; + clock-names = "se"; + + interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>, + <&aggre1_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config", + "qup-memory"; + + dmas = <&gpi_dma1 0 4 QCOM_GPI_SPI>, + <&gpi_dma1 1 4 QCOM_GPI_SPI>; + dma-names = "tx", + "rx"; + + pinctrl-0 = <&qup_spi4_data_clk>, <&qup_spi4_cs>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + i2c5: i2c@a94000 { + compatible = "qcom,geni-i2c"; + reg = <0x0 0x00a94000 0x0 0x4000>; + + interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>; + clock-names = "se"; + + interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>, + <&aggre1_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config", + "qup-memory"; + + dmas = <&gpi_dma1 0 5 QCOM_GPI_I2C>, + <&gpi_dma1 1 5 QCOM_GPI_I2C>; + dma-names = "tx", + "rx"; + + pinctrl-0 = <&qup_i2c5_data_clk>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + spi5: spi@a94000 { + compatible = "qcom,geni-spi"; + reg = <0x0 0x00a94000 0x0 0x4000>; + + interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>; + clock-names = "se"; + + interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>, + <&aggre1_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config", + "qup-memory"; + + dmas = <&gpi_dma1 0 5 QCOM_GPI_SPI>, + <&gpi_dma1 1 5 QCOM_GPI_SPI>; + dma-names = "tx", + "rx"; + + pinctrl-0 = <&qup_spi5_data_clk>, <&qup_spi5_cs>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + i2c6: i2c@a98000 { + compatible = "qcom,geni-i2c"; + reg = <0x0 0x00a98000 0x0 0x4000>; + + interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>; + clock-names = "se"; + + interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>, + <&aggre1_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config", + "qup-memory"; + + dmas = <&gpi_dma1 0 6 QCOM_GPI_I2C>, + <&gpi_dma1 1 6 QCOM_GPI_I2C>; + dma-names = "tx", + "rx"; + + pinctrl-0 = <&qup_i2c6_data_clk>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + spi6: spi@a98000 { + compatible = "qcom,geni-spi"; + reg = <0x0 0x00a98000 0x0 0x4000>; + + interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>; + clock-names = "se"; + + interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>, + <&aggre1_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config", + "qup-memory"; + + dmas = <&gpi_dma1 0 6 QCOM_GPI_SPI>, + <&gpi_dma1 1 6 QCOM_GPI_SPI>; + dma-names = "tx", + "rx"; + + pinctrl-0 = <&qup_spi6_data_clk>, <&qup_spi6_cs>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + + uart7: serial@a9c000 { + compatible = "qcom,geni-debug-uart"; + reg = <0x0 0x00a9c000 0x0 0x4000>; + + interrupts = <GIC_SPI 579 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>; + clock-names = "se"; + + interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS + &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>, + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS + &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>; + interconnect-names = "qup-core", + "qup-config"; + + + pinctrl-0 = <&qup_uart7_default>; + pinctrl-names = "default"; + + status = "disabled"; + }; + }; + + cnoc_main: interconnect@1500000 { + compatible = "qcom,sm8750-cnoc-main"; + reg = <0x0 0x01500000 0x0 0x16080>; + qcom,bcm-voters = <&apps_bcm_voter>; + #interconnect-cells = <2>; + }; + + config_noc: interconnect@1600000 { + compatible = "qcom,sm8750-config-noc"; + reg = <0x0 0x01600000 0x0 0x6200>; + qcom,bcm-voters = <&apps_bcm_voter>; + #interconnect-cells = <2>; + }; + + system_noc: interconnect@1680000 { + compatible = "qcom,sm8750-system-noc"; + reg = <0x0 0x01680000 0x0 0x1d080>; + qcom,bcm-voters = <&apps_bcm_voter>; + #interconnect-cells = <2>; + }; + + pcie_noc: interconnect@16c0000 { + compatible = "qcom,sm8750-pcie-anoc"; + reg = <0x0 0x016c0000 0x0 0x11400>; + qcom,bcm-voters = <&apps_bcm_voter>; + #interconnect-cells = <2>; + clocks = <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>, + <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>; + + }; + + aggre1_noc: interconnect@16e0000 { + compatible = "qcom,sm8750-aggre1-noc"; + reg = <0x0 0x016e0000 0x0 0x16400>; + qcom,bcm-voters = <&apps_bcm_voter>; + #interconnect-cells = <2>; + clocks = <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>, + <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>; + + }; + + aggre2_noc: interconnect@1700000 { + compatible = "qcom,sm8750-aggre2-noc"; + reg = <0x0 0x01700000 0x0 0x1f400>; + qcom,bcm-voters = <&apps_bcm_voter>; + #interconnect-cells = <2>; + clocks = <&rpmhcc RPMH_IPA_CLK>; + }; + + mmss_noc: interconnect@1780000 { + compatible = "qcom,sm8750-mmss-noc"; + reg = <0x0 0x01780000 0x0 0x5b800>; + qcom,bcm-voters = <&apps_bcm_voter>; + #interconnect-cells = <2>; + }; + + tcsr_mutex: hwlock@1f40000 { + compatible = "qcom,tcsr-mutex"; + reg = <0x0 0x01f40000 0x0 0x20000>; + #hwlock-cells = <1>; + }; + + lpass_ag_noc: interconnect@7e40000 { + compatible = "qcom,sm8750-lpass-ag-noc"; + reg = <0x0 0x07e40000 0x0 0xe080>; + qcom,bcm-voters = <&apps_bcm_voter>; + #interconnect-cells = <2>; + }; + + lpass_lpiaon_noc: interconnect@7400000 { + compatible = "qcom,sm8750-lpass-lpiaon-noc"; + reg = <0x0 0x07400000 0x0 0x19080>; + qcom,bcm-voters = <&apps_bcm_voter>; + #interconnect-cells = <2>; + }; + + lpass_lpicx_noc: interconnect@7420000 { + compatible = "qcom,sm8750-lpass-lpicx-noc"; + reg = <0x0 0x07420000 0x0 0x44080>; + qcom,bcm-voters = <&apps_bcm_voter>; + #interconnect-cells = <2>; + }; + + pdc: interrupt-controller@b220000 { + compatible = "qcom,sm8750-pdc", "qcom,pdc"; + reg = <0x0 0x0b220000 0x0 0x10000>, <0x0 0x164400f0 0x0 0x64>; + + qcom,pdc-ranges = <0 745 51>, <51 527 47>, + <98 609 32>, <130 717 12>, + <142 251 5>, <147 796 16>; + #interrupt-cells = <2>; + interrupt-parent = <&intc>; + interrupt-controller; + }; + + spmi_bus: spmi@c400000 { + compatible = "qcom,spmi-pmic-arb"; + reg = <0x0 0x0c400000 0x0 0x3000>, + <0x0 0x0c500000 0x0 0x400000>, + <0x0 0x0c440000 0x0 0x80000>, + <0x0 0x0c4c0000 0x0 0x10000>, + <0x0 0x0c42d000 0x0 0x4000>; + reg-names = "core", + "chnls", + "obsrvr", + "intr", + "cnfg"; + + interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "periph_irq"; + + qcom,ee = <0>; + qcom,channel = <0>; + qcom,bus-id = <0>; + + interrupt-controller; + #interrupt-cells = <4>; + + #address-cells = <2>; + #size-cells = <0>; + }; + + tlmm: pinctrl@f100000 { + compatible = "qcom,sm8750-tlmm"; + reg = <0x0 0x0f100000 0x0 0x102000>; + + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + + gpio-ranges = <&tlmm 0 0 216>; + wakeup-parent = <&pdc>; + + hub_i2c0_data_clk: hub-i2c0-data-clk-state { + /* SDA, SCL */ + pins = "gpio64", "gpio65"; + function = "i2chub0_se0"; + drive-strength = <2>; + bias-pull-up; + }; + + hub_i2c1_data_clk: hub-i2c1-data-clk-state { + /* SDA, SCL */ + pins = "gpio66", "gpio67"; + function = "i2chub0_se1"; + drive-strength = <2>; + bias-pull-up; + }; + + hub_i2c2_data_clk: hub-i2c2-data-clk-state { + /* SDA, SCL */ + pins = "gpio68", "gpio69"; + function = "i2chub0_se2"; + drive-strength = <2>; + bias-pull-up; + }; + + hub_i2c3_data_clk: hub-i2c3-data-clk-state { + /* SDA, SCL */ + pins = "gpio70", "gpio71"; + function = "i2chub0_se3"; + drive-strength = <2>; + bias-pull-up; + }; + + hub_i2c4_data_clk: hub-i2c4-data-clk-state { + /* SDA, SCL */ + pins = "gpio72", "gpio73"; + function = "i2chub0_se4"; + drive-strength = <2>; + bias-pull-up; + }; + + hub_i2c5_data_clk: hub-i2c5-data-clk-state { + /* SDA, SCL */ + pins = "gpio74", "gpio75"; + function = "i2chub0_se5"; + drive-strength = <2>; + bias-pull-up; + }; + + hub_i2c6_data_clk: hub-i2c6-data-clk-state { + /* SDA, SCL */ + pins = "gpio76", "gpio77"; + function = "i2chub0_se6"; + drive-strength = <2>; + bias-pull-up; + }; + + hub_i2c7_data_clk: hub-i2c7-data-clk-state { + /* SDA, SCL */ + pins = "gpio82", "gpio83"; + function = "i2chub0_se7"; + drive-strength = <2>; + bias-pull-up; + }; + + hub_i2c8_data_clk: hub-i2c8-data-clk-state { + /* SDA, SCL */ + pins = "gpio206", "gpio207"; + function = "i2chub0_se8"; + drive-strength = <2>; + bias-pull-up; + }; + + hub_i2c9_data_clk: hub-i2c9-data-clk-state { + /* SDA, SCL */ + pins = "gpio80", "gpio81"; + function = "i2chub0_se9"; + drive-strength = <2>; + bias-pull-up; + }; + + pcie0_default_state: pcie0-default-state { + perst-pins { + pins = "gpio102"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + }; + + clkreq-pins { + pins = "gpio103"; + function = "pcie0_clk_req_n"; + drive-strength = <2>; + bias-pull-up; + }; + + wake-pins { + pins = "gpio104"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + qup_i2c0_data_clk: qup-i2c0-data-clk-state { + /* SDA, SCL */ + pins = "gpio32", "gpio33"; + function = "qup1_se0"; + drive-strength = <2>; + bias-pull-up; + }; + + qup_i2c1_data_clk: qup-i2c1-data-clk-state { + /* SDA, SCL */ + pins = "gpio36", "gpio37"; + function = "qup1_se1"; + drive-strength = <2>; + bias-pull-up; + }; + + qup_i2c2_data_clk: qup-i2c2-data-clk-state { + /* SDA, SCL */ + pins = "gpio40", "gpio41"; + function = "qup1_se2"; + drive-strength = <2>; + bias-pull-up; + }; + + qup_i2c3_data_clk: qup-i2c3-data-clk-state { + /* SDA, SCL */ + pins = "gpio44", "gpio45"; + function = "qup1_se3"; + drive-strength = <2>; + bias-pull-up; + }; + + qup_i2c4_data_clk: qup-i2c4-data-clk-state { + /* SDA, SCL */ + pins = "gpio48", "gpio49"; + function = "qup1_se4"; + drive-strength = <2>; + bias-pull-up; + }; + + qup_i2c5_data_clk: qup-i2c5-data-clk-state { + /* SDA, SCL */ + pins = "gpio52", "gpio53"; + function = "qup1_se5"; + drive-strength = <2>; + bias-pull-up; + }; + + qup_i2c6_data_clk: qup-i2c6-data-clk-state { + /* SDA, SCL */ + pins = "gpio56", "gpio57"; + function = "qup1_se6"; + drive-strength = <2>; + bias-pull-up; + }; + + qup_i2c8_data_clk: qup-i2c8-data-clk-state { + /* SDA, SCL */ + pins = "gpio0", "gpio1"; + function = "qup2_se0"; + drive-strength = <2>; + bias-pull-up; + }; + + qup_i2c9_data_clk: qup-i2c9-data-clk-state { + /* SDA, SCL */ + pins = "gpio4", "gpio5"; + function = "qup2_se1"; + drive-strength = <2>; + bias-pull-up; + }; + + qup_i2c10_data_clk: qup-i2c10-data-clk-state { + /* SDA, SCL */ + pins = "gpio8", "gpio9"; + function = "qup2_se2"; + drive-strength = <2>; + bias-pull-up; + }; + + qup_i2c11_data_clk: qup-i2c11-data-clk-state { + /* SDA, SCL */ + pins = "gpio12", "gpio13"; + function = "qup2_se3"; + drive-strength = <2>; + bias-pull-up; + }; + + qup_i2c12_data_clk: qup-i2c12-data-clk-state { + /* SDA, SCL */ + pins = "gpio16", "gpio17"; + function = "qup2_se4"; + drive-strength = <2>; + bias-pull-up; + }; + + qup_i2c13_data_clk: qup-i2c13-data-clk-state { + /* SDA, SCL */ + pins = "gpio20", "gpio21"; + function = "qup2_se5"; + drive-strength = <2>; + bias-pull-up; + }; + + qup_i2c15_data_clk: qup-i2c15-data-clk-state { + /* SDA, SCL */ + pins = "gpio28", "gpio29"; + function = "qup2_se7"; + drive-strength = <2>; + bias-pull-up; + }; + + qup_spi0_cs: qup-spi0-cs-state { + pins = "gpio35"; + function = "qup1_se0"; + drive-strength = <6>; + bias-disable; + }; + + qup_spi0_data_clk: qup-spi0-data-clk-state { + /* MISO, MOSI, CLK */ + pins = "gpio32", "gpio33", "gpio34"; + function = "qup1_se0"; + drive-strength = <6>; + bias-disable; + }; + + qup_spi1_cs: qup-spi1-cs-state { + pins = "gpio39"; + function = "qup1_se1"; + drive-strength = <6>; + bias-disable; + }; + + qup_spi1_data_clk: qup-spi1-data-clk-state { + /* MISO, MOSI, CLK */ + pins = "gpio36", "gpio37", "gpio38"; + function = "qup1_se1"; + drive-strength = <6>; + bias-disable; + }; + + qup_spi2_cs: qup-spi2-cs-state { + pins = "gpio43"; + function = "qup1_se2"; + drive-strength = <6>; + bias-disable; + }; + + qup_spi2_data_clk: qup-spi2-data-clk-state { + /* MISO, MOSI, CLK */ + pins = "gpio40", "gpio41", "gpio42"; + function = "qup1_se2"; + drive-strength = <6>; + bias-disable; + }; + + qup_spi3_cs: qup-spi3-cs-state { + pins = "gpio47"; + function = "qup1_se3"; + drive-strength = <6>; + bias-disable; + }; + + qup_spi3_data_clk: qup-spi3-data-clk-state { + /* MISO, MOSI, CLK */ + pins = "gpio44", "gpio45", "gpio46"; + function = "qup1_se3"; + drive-strength = <6>; + bias-disable; + }; + + qup_spi4_cs: qup-spi4-cs-state { + pins = "gpio51"; + function = "qup1_se4"; + drive-strength = <6>; + bias-disable; + }; + + qup_spi4_data_clk: qup-spi4-data-clk-state { + /* MISO, MOSI, CLK */ + pins = "gpio48", "gpio49", "gpio50"; + function = "qup1_se4"; + drive-strength = <6>; + bias-disable; + }; + + qup_spi5_cs: qup-spi5-cs-state { + pins = "gpio55"; + function = "qup1_se5"; + drive-strength = <6>; + bias-disable; + }; + + qup_spi5_data_clk: qup-spi5-data-clk-state { + /* MISO, MOSI, CLK */ + pins = "gpio52", "gpio53", "gpio54"; + function = "qup1_se5"; + drive-strength = <6>; + bias-disable; + }; + + qup_spi6_cs: qup-spi6-cs-state { + pins = "gpio59"; + function = "qup1_se6"; + drive-strength = <6>; + bias-disable; + }; + + qup_spi6_data_clk: qup-spi6-data-clk-state { + /* MISO, MOSI, CLK */ + pins = "gpio56", "gpio57", "gpio58"; + function = "qup1_se6"; + drive-strength = <6>; + bias-disable; + }; + + qup_spi8_cs: qup-spi8-cs-state { + pins = "gpio3"; + function = "qup2_se0"; + drive-strength = <6>; + bias-disable; + }; + + qup_spi8_data_clk: qup-spi8-data-clk-state { + /* MISO, MOSI, CLK */ + pins = "gpio0", "gpio1", "gpio2"; + function = "qup2_se0"; + drive-strength = <6>; + bias-disable; + }; + + qup_spi9_cs: qup-spi9-cs-state { + pins = "gpio7"; + function = "qup2_se1"; + drive-strength = <6>; + bias-disable; + }; + + qup_spi9_data_clk: qup-spi9-data-clk-state { + /* MISO, MOSI, CLK */ + pins = "gpio4", "gpio5", "gpio6"; + function = "qup2_se1"; + drive-strength = <6>; + bias-disable; + }; + + qup_spi10_cs: qup-spi10-cs-state { + pins = "gpio11"; + function = "qup2_se2"; + drive-strength = <6>; + bias-disable; + }; + + qup_spi10_data_clk: qup-spi10-data-clk-state { + /* MISO, MOSI, CLK */ + pins = "gpio8", "gpio9", "gpio10"; + function = "qup2_se2"; + drive-strength = <6>; + bias-disable; + }; + + qup_spi11_cs: qup-spi11-cs-state { + pins = "gpio15"; + function = "qup2_se3"; + drive-strength = <6>; + bias-disable; + }; + + qup_spi11_data_clk: qup-spi11-data-clk-state { + /* MISO, MOSI, CLK */ + pins = "gpio12", "gpio13", "gpio14"; + function = "qup2_se3"; + drive-strength = <6>; + bias-disable; + }; + + qup_spi12_cs: qup-spi12-cs-state { + pins = "gpio19"; + function = "qup2_se4"; + drive-strength = <6>; + bias-disable; + }; + + qup_spi12_data_clk: qup-spi12-data-clk-state { + /* MISO, MOSI, CLK */ + pins = "gpio16", "gpio17", "gpio18"; + function = "qup2_se4"; + drive-strength = <6>; + bias-disable; + }; + + qup_spi13_cs: qup-spi13-cs-state { + pins = "gpio23"; + function = "qup2_se5"; + drive-strength = <6>; + bias-pull-up; + }; + + qup_spi13_data_clk: qup-spi13-data-clk-state { + /* MISO, MOSI, CLK */ + pins = "gpio20", "gpio21", "gpio22"; + function = "qup2_se5"; + drive-strength = <6>; + bias-disable; + }; + + qup_spi15_cs: qup-spi15-cs-state { + pins = "gpio31"; + function = "qup2_se7"; + drive-strength = <6>; + bias-disable; + }; + + qup_spi15_data_clk: qup-spi15-data-clk-state { + /* MISO, MOSI, CLK */ + pins = "gpio28", "gpio29", "gpio30"; + function = "qup2_se7"; + drive-strength = <6>; + bias-disable; + }; + + qup_uart7_default: qup-uart7-default-state { + /* TX, RX */ + pins = "gpio62", "gpio63"; + function = "qup1_se7"; + drive-strength = <2>; + bias-disable; + }; + + qup_uart14_default: qup-uart14-default-state { + /* TX, RX */ + pins = "gpio26", "gpio27"; + function = "qup2_se6"; + drive-strength = <2>; + bias-pull-up; + }; + + qup_uart14_cts_rts: qup-uart14-cts-rts-state { + /* CTS, RTS */ + pins = "gpio24", "gpio25"; + function = "qup2_se6"; + drive-strength = <2>; + bias-pull-down; + }; + + sdc2_sleep: sdc2-sleep-state { + clk-pins { + pins = "sdc2_clk"; + drive-strength = <2>; + bias-disable; + }; + + cmd-pins { + pins = "sdc2_cmd"; + drive-strength = <2>; + bias-pull-up; + }; + + data-pins { + pins = "sdc2_data"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + sdc2_default: sdc2-default-state { + clk-pins { + pins = "sdc2_clk"; + drive-strength = <16>; + bias-disable; + }; + + cmd-pins { + pins = "sdc2_cmd"; + drive-strength = <10>; + bias-pull-up; + }; + + data-pins { + pins = "sdc2_data"; + drive-strength = <10>; + bias-pull-up; + }; + }; + }; + + tcsrcc: clock-controller@f204008 { + compatible = "qcom,sm8750-tcsr", "syscon"; + reg = <0x0 0x0f204008 0x0 0x3004>; + + clocks = <&rpmhcc RPMH_CXO_CLK>; + + #clock-cells = <1>; + #reset-cells = <1>; + }; + + apps_smmu: iommu@15000000 { + compatible = "qcom,sm8750-smmu-500", "qcom,smmu-500", "arm,mmu-500"; + reg = <0x0 0x15000000 0x0 0x100000>; + + interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 409 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 412 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 707 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 690 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 691 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 692 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 693 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 694 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 695 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 696 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 697 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 410 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 488 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 489 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 490 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 491 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 492 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 493 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 494 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 495 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 496 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 497 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 498 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 499 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 500 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 501 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 502 IRQ_TYPE_LEVEL_HIGH>; + + #iommu-cells = <2>; + #global-interrupts = <1>; + + dma-coherent; + }; + + intc: interrupt-controller@16000000 { + compatible = "arm,gic-v3"; + reg = <0x0 0x16000000 0x0 0x10000>, + <0x0 0x16080000 0x0 0x200000>; + + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; + + #interrupt-cells = <3>; + interrupt-controller; + + #redistributor-regions = <1>; + redistributor-stride = <0x0 0x40000>; + + #address-cells = <2>; + #size-cells = <2>; + ranges; + + gic_its: msi-controller@16040000 { + compatible = "arm,gic-v3-its"; + reg = <0x0 0x16040000 0x0 0x20000>; + + msi-controller; + #msi-cells = <1>; + + status = "disabled"; + }; + }; + + apps_rsc: rsc@16500000 { + compatible = "qcom,rpmh-rsc"; + reg = <0x0 0x16500000 0x0 0x10000>, + <0x0 0x16510000 0x0 0x10000>, + <0x0 0x16520000 0x0 0x10000>; + reg-names = "drv-0", + "drv-1", + "drv-2"; + + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; + qcom,tcs-offset = <0xd00>; + qcom,drv-id = <2>; + qcom,tcs-config = <ACTIVE_TCS 3>, <SLEEP_TCS 2>, + <WAKE_TCS 2>, <CONTROL_TCS 0>; + + label = "apps_rsc"; + + power-domains = <&system_pd>; + + apps_bcm_voter: bcm-voter { + compatible = "qcom,bcm-voter"; + }; + + rpmhcc: clock-controller { + compatible = "qcom,sm8750-rpmh-clk"; + + clocks = <&xo_board>; + clock-names = "xo"; + + #clock-cells = <1>; + }; + + rpmhpd: power-controller { + compatible = "qcom,sm8750-rpmhpd"; + + operating-points-v2 = <&rpmhpd_opp_table>; + + #power-domain-cells = <1>; + + rpmhpd_opp_table: opp-table { + compatible = "operating-points-v2"; + + rpmhpd_opp_ret: opp-16 { + opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>; + }; + + rpmhpd_opp_min_svs: opp-48 { + opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>; + }; + + rpmhpd_opp_low_svs_d3: opp-50 { + opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS_D3>; + }; + + rpmhpd_opp_low_svs_d2: opp-52 { + opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS_D2>; + }; + + rpmhpd_opp_low_svs_d1: opp-56 { + opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS_D1>; + }; + + rpmhpd_opp_low_svs_d0: opp-60 { + opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS_D0>; + }; + + rpmhpd_opp_low_svs: opp-64 { + opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>; + }; + + rpmhpd_opp_low_svs_l1: opp-80 { + opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS_L1>; + }; + + rpmhpd_opp_svs: opp-128 { + opp-level = <RPMH_REGULATOR_LEVEL_SVS>; + }; + + rpmhpd_opp_svs_l0: opp-144 { + opp-level = <RPMH_REGULATOR_LEVEL_SVS_L0>; + }; + + rpmhpd_opp_svs_l1: opp-192 { + opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>; + }; + + rpmhpd_opp_svs_l2: opp-224 { + opp-level = <RPMH_REGULATOR_LEVEL_SVS_L2>; + }; + + rpmhpd_opp_nom: opp-256 { + opp-level = <RPMH_REGULATOR_LEVEL_NOM>; + }; + + rpmhpd_opp_nom_l1: opp-320 { + opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>; + }; + + rpmhpd_opp_nom_l2: opp-336 { + opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>; + }; + + rpmhpd_opp_turbo: opp-384 { + opp-level = <RPMH_REGULATOR_LEVEL_TURBO>; + }; + + rpmhpd_opp_turbo_l1: opp-416 { + opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>; + }; + + rpmhpd_opp_turbo_l2: opp-432 { + opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L2>; + }; + + rpmhpd_opp_turbo_l3: opp-448 { + opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L3>; + }; + + rpmhpd_opp_turbo_l4: opp-452 { + opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L4>; + }; + + rpmhpd_opp_super_turbo_no_cpr: opp-480 { + opp-level = + <RPMH_REGULATOR_LEVEL_SUPER_TURBO_NO_CPR>; + }; + }; + }; + }; + + timer@16800000 { + compatible = "arm,armv7-timer-mem"; + reg = <0x0 0x16800000 0x0 0x1000>; + + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0 0 0x20000000>; + + frame@16801000 { + reg = <0x0 0x16801000 0x1000>, + <0x0 0x16802000 0x1000>; + + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; + + frame-number = <0>; + }; + + frame@16803000 { + reg = <0x0 0x16803000 0x1000>; + + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; + + frame-number = <1>; + + status = "disabled"; + }; + + frame@16805000 { + reg = <0x0 0x16805000 0x1000>; + + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + + frame-number = <2>; + + status = "disabled"; + }; + + frame@16807000 { + reg = <0x0 0x16807000 0x1000>; + + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + + frame-number = <3>; + + status = "disabled"; + }; + + frame@16809000 { + reg = <0x0 0x16809000 0x1000>; + + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + + frame-number = <4>; + + status = "disabled"; + }; + + frame@1680b000 { + reg = <0x0 0x1680b000 0x1000>; + + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + + frame-number = <5>; + + status = "disabled"; + }; + + frame@1680d000 { + reg = <0x0 0x1680d000 0x1000>; + + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + + frame-number = <6>; + + status = "disabled"; + }; + }; + + gem_noc: interconnect@24100000 { + compatible = "qcom,sm8750-gem-noc"; + reg = <0x0 0x24100000 0x0 0x14b080>; + qcom,bcm-voters = <&apps_bcm_voter>; + #interconnect-cells = <2>; + }; + + nsp_noc: interconnect@320c0000 { + compatible = "qcom,sm8750-nsp-noc"; + reg = <0x0 0x320c0000 0x0 0x13080>; + qcom,bcm-voters = <&apps_bcm_voter>; + #interconnect-cells = <2>; + }; + }; + + timer { + compatible = "arm,armv8-timer"; + + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, + <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, + <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, + <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; + }; +}; -- 2.46.1 ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v2 3/6] arm64: dts: qcom: Add base SM8750 dtsi 2024-11-12 0:49 ` [PATCH v2 3/6] arm64: dts: qcom: Add base SM8750 dtsi Melody Olvera @ 2024-11-15 20:26 ` Konrad Dybcio 0 siblings, 0 replies; 12+ messages in thread From: Konrad Dybcio @ 2024-11-15 20:26 UTC (permalink / raw) To: Melody Olvera, Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Catalin Marinas, Will Deacon, Geert Uytterhoeven, Dmitry Baryshkov, Neil Armstrong, Arnd Bergmann, Nícolas F . R . A . Prado, Trilok Soni, Satya Durga Srinivasu Prabhala Cc: linux-arm-msm, devicetree, linux-kernel, linux-arm-kernel, Taniya Das, Jishnu Prakash, Raviteja Laggyshetty On 12.11.2024 1:49 AM, Melody Olvera wrote: > Add the base dtsi for the SM8750 SoC describing the CPUs, GCC and > RPMHCC clock controllers, geni UART, interrupt controller, TLMM, > reserved memory, interconnects, and SMMU. > > Co-developed-by: Taniya Das <quic_tdas@quicinc.com> > Signed-off-by: Taniya Das <quic_tdas@quicinc.com> > Co-developed-by: Jishnu Prakash <quic_jprakash@quicinc.com> > Signed-off-by: Jishnu Prakash <quic_jprakash@quicinc.com> > Co-developed-by: Raviteja Laggyshetty <quic_rlaggysh@quicinc.com> > Signed-off-by: Raviteja Laggyshetty <quic_rlaggysh@quicinc.com> > Signed-off-by: Melody Olvera <quic_molvera@quicinc.com> > --- [...] > + power-domain-names = "psci"; > + cpu-idle-states = <&cluster0_c4>; So here and on x1 we use cpu-idle-states instead of putting the idle state under domain-idle-states in CPU_PDn like on other PSCI OSI mode-supporting SoCs. IIUC it works out to be the same thing, but maybe we should stick to the latter for consistency [...] > + > + gic_its: msi-controller@16040000 { > + compatible = "arm,gic-v3-its"; > + reg = <0x0 0x16040000 0x0 0x20000>; > + > + msi-controller; > + #msi-cells = <1>; > + > + status = "disabled"; > + }; Any reason it's disabled? LGTM otherwise Konrad ^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v2 4/6] arm64: dts: qcom: sm8750: Add pmic dtsi 2024-11-12 0:49 [PATCH v2 0/6] dts: qcom: Introduce SM8750 device trees Melody Olvera ` (2 preceding siblings ...) 2024-11-12 0:49 ` [PATCH v2 3/6] arm64: dts: qcom: Add base SM8750 dtsi Melody Olvera @ 2024-11-12 0:49 ` Melody Olvera 2024-11-12 0:49 ` [PATCH v2 5/6] arm64: dts: qcom: Add SM8750 MTP and QRD boards Melody Olvera 2024-11-12 0:49 ` [PATCH v2 6/6] arm64: defconfig: Enable SM8750 SoC base configs Melody Olvera 5 siblings, 0 replies; 12+ messages in thread From: Melody Olvera @ 2024-11-12 0:49 UTC (permalink / raw) To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Catalin Marinas, Will Deacon, Geert Uytterhoeven, Dmitry Baryshkov, Neil Armstrong, Arnd Bergmann, Nícolas F . R . A . Prado, Trilok Soni, Satya Durga Srinivasu Prabhala Cc: linux-arm-msm, devicetree, linux-kernel, linux-arm-kernel, Melody Olvera Add pmic dtsi file for SM8750 SoC describing the pmics and their thermal zones. Signed-off-by: Melody Olvera <quic_molvera@quicinc.com> --- arch/arm64/boot/dts/qcom/sm8750-pmics.dtsi | 188 +++++++++++++++++++++ 1 file changed, 188 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sm8750-pmics.dtsi diff --git a/arch/arm64/boot/dts/qcom/sm8750-pmics.dtsi b/arch/arm64/boot/dts/qcom/sm8750-pmics.dtsi new file mode 100644 index 000000000000..6eb8d78937c3 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sm8750-pmics.dtsi @@ -0,0 +1,188 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved. + */ + +/ { + thermal-zones { + pm8550ve-d-thermal { + polling-delay-passive = <100>; + + thermal-sensors = <&pm8550ve_d_temp_alarm>; + + trips { + trip0 { + temperature = <95000>; + hysteresis = <0>; + type = "passive"; + }; + + trip1 { + temperature = <115000>; + hysteresis = <0>; + type = "hot"; + }; + }; + }; + + pm8550ve-f-thermal { + polling-delay-passive = <100>; + + thermal-sensors = <&pm8550ve_f_temp_alarm>; + + trips { + trip0 { + temperature = <95000>; + hysteresis = <0>; + type = "passive"; + }; + + trip1 { + temperature = <115000>; + hysteresis = <0>; + type = "hot"; + }; + }; + }; + + pm8550ve-g-thermal { + polling-delay-passive = <100>; + + thermal-sensors = <&pm8550ve_g_temp_alarm>; + + trips { + trip0 { + temperature = <95000>; + hysteresis = <0>; + type = "passive"; + }; + + trip1 { + temperature = <115000>; + hysteresis = <0>; + type = "hot"; + }; + }; + }; + + pm8550vs-j-thermal { + polling-delay-passive = <100>; + + thermal-sensors = <&pm8550vs_j_temp_alarm>; + + trips { + trip0 { + temperature = <95000>; + hysteresis = <0>; + type = "passive"; + }; + + trip1 { + temperature = <115000>; + hysteresis = <0>; + type = "hot"; + }; + }; + }; + }; +}; + +&spmi_bus { + /* PM8550VE */ + pm8550ve_d: pmic@3 { + compatible = "qcom,pm8550ve", "qcom,spmi-pmic"; + reg = <0x3 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pm8550ve_d_temp_alarm: temp-alarm@a00 { + compatible = "qcom,spmi-temp-alarm"; + reg = <0xa00>; + interrupts = <0x3 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; + #thermal-sensor-cells = <0>; + }; + + pm8550ve_d_gpios: gpio@8800 { + compatible = "qcom,pm8550ve-gpio", "qcom,spmi-gpio"; + reg = <0x8800>; + gpio-controller; + gpio-ranges = <&pm8550ve_d_gpios 0 0 8>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + + pm8550ve_f: pmic@5 { + compatible = "qcom,pm8550ve", "qcom,spmi-pmic"; + reg = <0x5 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pm8550ve_f_temp_alarm: temp-alarm@a00 { + compatible = "qcom,spmi-temp-alarm"; + reg = <0xa00>; + interrupts = <0x5 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; + #thermal-sensor-cells = <0>; + }; + + pm8550ve_f_gpios: gpio@8800 { + compatible = "qcom,pm8550ve-gpio", "qcom,spmi-gpio"; + reg = <0x8800>; + gpio-controller; + gpio-ranges = <&pm8550ve_f_gpios 0 0 6>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + + pm8550ve_g: pmic@6 { + compatible = "qcom,pm8550ve", "qcom,spmi-pmic"; + reg = <0x6 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pm8550ve_g_temp_alarm: temp-alarm@a00 { + compatible = "qcom,spmi-temp-alarm"; + reg = <0xa00>; + interrupts = <0x6 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; + #thermal-sensor-cells = <0>; + }; + + pm8550ve_g_gpios: gpio@8800 { + compatible = "qcom,pm8550ve-gpio", "qcom,spmi-gpio"; + reg = <0x8800>; + gpio-controller; + gpio-ranges = <&pm8550ve_g_gpios 0 0 8>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + + /* PM8550VS */ + pm8550vs_j: pmic@9 { + compatible = "qcom,pm8550vs", "qcom,spmi-pmic"; + reg = <0x9 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pm8550vs_j_temp_alarm: temp-alarm@a00 { + compatible = "qcom,spmi-temp-alarm"; + reg = <0xa00>; + interrupts = <0x9 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; + #thermal-sensor-cells = <0>; + }; + + pm8550vs_j_gpios: gpio@8800 { + compatible = "qcom,pm8550vs-gpio", "qcom,spmi-gpio"; + reg = <0x8800>; + gpio-controller; + gpio-ranges = <&pm8550vs_j_gpios 0 0 6>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; +}; -- 2.46.1 ^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v2 5/6] arm64: dts: qcom: Add SM8750 MTP and QRD boards 2024-11-12 0:49 [PATCH v2 0/6] dts: qcom: Introduce SM8750 device trees Melody Olvera ` (3 preceding siblings ...) 2024-11-12 0:49 ` [PATCH v2 4/6] arm64: dts: qcom: sm8750: Add pmic dtsi Melody Olvera @ 2024-11-12 0:49 ` Melody Olvera 2024-11-12 0:49 ` [PATCH v2 6/6] arm64: defconfig: Enable SM8750 SoC base configs Melody Olvera 5 siblings, 0 replies; 12+ messages in thread From: Melody Olvera @ 2024-11-12 0:49 UTC (permalink / raw) To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Catalin Marinas, Will Deacon, Geert Uytterhoeven, Dmitry Baryshkov, Neil Armstrong, Arnd Bergmann, Nícolas F . R . A . Prado, Trilok Soni, Satya Durga Srinivasu Prabhala Cc: linux-arm-msm, devicetree, linux-kernel, linux-arm-kernel, Melody Olvera Add MTP and QRD dts files for SM8750 describing board clocks, regulators, gpio keys, etc. Signed-off-by: Melody Olvera <quic_molvera@quicinc.com> --- arch/arm64/boot/dts/qcom/Makefile | 2 + arch/arm64/boot/dts/qcom/sm8750-mtp.dts | 794 ++++++++++++++++++++++++ arch/arm64/boot/dts/qcom/sm8750-qrd.dts | 792 +++++++++++++++++++++++ 3 files changed, 1588 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sm8750-mtp.dts create mode 100644 arch/arm64/boot/dts/qcom/sm8750-qrd.dts diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index 9bb8b191aeb5..0019e2351232 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -281,6 +281,8 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8650-hdk-display-card.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8650-hdk.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8650-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8650-qrd.dtb +dtb-$(CONFIG_ARCH_QCOM) += sm8750-mtp.dtb +dtb-$(CONFIG_ARCH_QCOM) += sm8750-qrd.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e001de-devkit.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e78100-lenovo-thinkpad-t14s.dtb dtb-$(CONFIG_ARCH_QCOM) += x1e80100-asus-vivobook-s15.dtb diff --git a/arch/arm64/boot/dts/qcom/sm8750-mtp.dts b/arch/arm64/boot/dts/qcom/sm8750-mtp.dts new file mode 100644 index 000000000000..9e3aacad7bda --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sm8750-mtp.dts @@ -0,0 +1,794 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved. + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> +#include "sm8750.dtsi" +#include "pm8010.dtsi" +#include "pm8550.dtsi" +#define PMK8550VE_SID 8 +#include "pm8550ve.dtsi" +#include "pmd8028.dtsi" +#include "pmih0108.dtsi" +#include "pmk8550.dtsi" +#include "pmr735d_a.dtsi" +#include "sm8750-pmics.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. SM8750 MTP"; + compatible = "qcom,sm8750-mtp", "qcom,sm8750"; + chassis-type = "handset"; + + + aliases { + serial0 = &uart7; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + clocks { + xo_board: xo-board { + compatible = "fixed-clock"; + clock-frequency = <76800000>; + #clock-cells = <0>; + }; + + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + clock-frequency = <32000>; + #clock-cells = <0>; + }; + + bi_tcxo_div2: bi-tcxo-div2-clk { + compatible = "fixed-factor-clock"; + #clock-cells = <0>; + + clocks = <&rpmhcc RPMH_CXO_CLK>; + clock-mult = <1>; + clock-div = <2>; + }; + + bi_tcxo_ao_div2: bi-tcxo-ao-div2-clk { + compatible = "fixed-factor-clock"; + #clock-cells = <0>; + + clocks = <&rpmhcc RPMH_CXO_CLK_A>; + clock-mult = <1>; + clock-div = <2>; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-0 = <&volume_up_n>; + pinctrl-names = "default"; + + key-volume-up { + label = "Volume Up"; + linux,code = <KEY_VOLUMEUP>; + gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>; + debounce-interval = <15>; + linux,can-disable; + wakeup-source; + }; + }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + + regulator-always-on; + regulator-boot-on; + }; +}; + +&apps_rsc { + regulators-0 { + compatible = "qcom,pm8550-rpmh-regulators"; + + vdd-bob1-supply = <&vph_pwr>; + vdd-bob2-supply = <&vph_pwr>; + vdd-l1-l4-l10-supply = <&vreg_s3g_1p8>; + vdd-l2-l13-l14-supply = <&vreg_bob1>; + vdd-l3-supply = <&vreg_s7i_1p2>; + vdd-l5-l16-supply = <&vreg_bob1>; + vdd-l6-l7-supply = <&vreg_bob1>; + vdd-l8-l9-supply = <&vreg_bob1>; + vdd-l11-supply = <&vreg_s7i_1p2>; + vdd-l12-supply = <&vreg_s3g_1p8>; + vdd-l15-supply = <&vreg_s3g_1p8>; + vdd-l17-supply = <&vreg_bob2>; + + qcom,pmic-id = "b"; + + vreg_bob1: bob1 { + regulator-name = "vreg_bob1"; + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <4000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_bob2: bob2 { + regulator-name = "vreg_bob2"; + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1b_1p8: ldo1 { + regulator-name = "vreg_l1b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2b_3p0: ldo2 { + regulator-name = "vreg_l2b_3p0"; + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3048000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l4b_1p8: ldo4 { + regulator-name = "vreg_l4b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l5b_3p1: ldo5 { + regulator-name = "vreg_l5b_3p1"; + regulator-min-microvolt = <3100000>; + regulator-max-microvolt = <3148000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6b_1p8: ldo6 { + regulator-name = "vreg_l6b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7b_1p8: ldo7 { + regulator-name = "vreg_l7b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + + }; + + vreg_l8b_1p8: ldo8 { + regulator-name = "vreg_l8b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9b_2p9: ldo9 { + regulator-name = "vreg_l9b_2p9"; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l10b_1p8: ldo10 { + regulator-name = "vreg_l10b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l11b_1p0: ldo11 { + regulator-name = "vreg_l11b_1p0"; + regulator-min-microvolt = <1064000>; + regulator-max-microvolt = <1292000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l12b_1p8: ldo12 { + regulator-name = "vreg_l12b_1p8"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l13b_3p0: ldo13 { + regulator-name = "vreg_l13b_3p0"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l14b_3p2: ldo14 { + regulator-name = "vreg_l14b_3p2"; + regulator-min-microvolt = <3200000>; + regulator-max-microvolt = <3200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l15b_1p8: ldo15 { + regulator-name = "vreg_l15b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l16b_2p8: ldo16 { + regulator-name = "vreg_l16b_2p8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l17b_2p5: ldo17 { + regulator-name = "vreg_l17b_2p5"; + regulator-min-microvolt = <2504000>; + regulator-max-microvolt = <2504000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-1 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + + vdd-l1-supply = <&vreg_s7i_1p2>; + vdd-l2-supply = <&vreg_s1d_0p97>; + vdd-l3-supply = <&vreg_s1d_0p97>; + vdd-s1-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + + qcom,pmic-id = "d"; + + vreg_s1d_0p97: smps1 { + regulator-name = "vreg_s1d_0p97"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <1100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s3d_1p2: smps3 { + regulator-name = "vreg_s3d_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1300000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s4d_0p85: smps4 { + regulator-name = "vreg_s4d_0p85"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1036000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1d_1p2: ldo1 { + regulator-name = "vreg_l1d_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2d_0p88: ldo2 { + regulator-name = "vreg_l2d_0p88"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3d_0p88: ldo3 { + regulator-name = "vreg_l3d_0p88"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-2 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + + vdd-l1-supply = <&vreg_s1d_0p97>; + vdd-l2-supply = <&vreg_s7i_1p2>; + vdd-l3-supply = <&vreg_s3g_1p8>; + vdd-s5-supply = <&vph_pwr>; + + qcom,pmic-id = "f"; + + vreg_s5f_0p5: smps5 { + regulator-name = "vreg_s5f_0p5"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1f_0p88: ldo1 { + regulator-name = "vreg_l1f_0p88"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2f_1p2: ldo2 { + regulator-name = "vreg_l2f_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3f_1p8: ldo3 { + regulator-name = "vreg_l3f_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + }; + + regulators-3 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + + vdd-l1-supply = <&vreg_s1d_0p97>; + vdd-l2-supply = <&vreg_s3g_1p8>; + vdd-l3-supply = <&vreg_s7i_1p2>; + vdd-s1-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + + qcom,pmic-id = "g"; + + vreg_s1g_0p5: smps1 { + regulator-name = "vreg_s1g_0p5"; + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <700000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s3g_1p8: smps3 { + regulator-name = "vreg_s3g_1p8"; + regulator-min-microvolt = <1856000>; + regulator-max-microvolt = <2000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s4g_0p75: smps4 { + regulator-name = "vreg_s4g_0p75"; + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <900000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1g_0p91: ldo1 { + regulator-name = "vreg_l1g_0p91"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <936000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2g_1p8: ldo2 { + regulator-name = "vreg_l2g_1p8"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1860000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3g_1p2: ldo3 { + regulator-name = "vreg_l3g_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1256000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-4 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + + vdd-l1-supply = <&vreg_s7i_1p2>; + vdd-l2-supply = <&vreg_s7i_1p2>; + vdd-l3-supply = <&vreg_s1d_0p97>; + vdd-s7-supply = <&vph_pwr>; + vdd-s8-supply = <&vph_pwr>; + + qcom,pmic-id = "i"; + + vreg_s7i_1p2: smps7 { + regulator-name = "vreg_s7i_1p2"; + regulator-min-microvolt = <1224000>; + regulator-max-microvolt = <1340000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s8i_0p9: smps8 { + regulator-name = "vreg_s8i_0p9"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <972000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1i_1p2: ldo1 { + regulator-name = "vreg_l1i_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2i_1p2: ldo2 { + regulator-name = "vreg_l2i_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3i_0p88: ldo3 { + regulator-name = "vreg_l3i_0p88"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-5 { + compatible = "qcom,pm8550vs-rpmh-regulators"; + + vdd-l1-supply = <&vreg_s1d_0p97>; + vdd-l2-supply = <&vreg_s7i_1p2>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + + qcom,pmic-id = "j"; + + vreg_s2j_1p1: smps2 { + regulator-name = "vreg_s2j_1p1"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s3j_1p1: smps3 { + regulator-name = "vreg_s3j_1p1"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1j_0p91: ldo1 { + regulator-name = "vreg_l1j_0p91"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2j_1p2: ldo2 { + regulator-name = "vreg_l2j_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-6 { + compatible = "qcom,pm8010-rpmh-regulators"; + qcom,pmic-id = "m"; + + vdd-l1-l2-supply = <&vreg_s7i_1p2>; + vdd-l3-l4-supply = <&vreg_bob2>; + vdd-l5-supply = <&vreg_s3g_1p8>; + vdd-l6-supply = <&vreg_bob1>; + vdd-l7-supply = <&vreg_bob1>; + + vreg_l1m_1p1: ldo1 { + regulator-name = "vreg_l1m_1p1"; + regulator-min-microvolt = <1104000>; + regulator-max-microvolt = <1104000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2m_1p056: ldo2 { + regulator-name = "vreg_l2m_1p056"; + regulator-min-microvolt = <1056000>; + regulator-max-microvolt = <1056000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3m_2p8: ldo3 { + regulator-name = "vreg_l3m_2p8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l4m_2p8: ldo4 { + regulator-name = "vreg_l4m_2p8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l5m_1p8: ldo5 { + regulator-name = "vreg_l5m_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6m_2p8: ldo6 { + regulator-name = "vreg_l6m_2p8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7m_2p96: ldo7 { + regulator-name = "vreg_l7m_2p96"; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-7 { + compatible = "qcom,pm8010-rpmh-regulators"; + qcom,pmic-id = "n"; + + vdd-l1-l2-supply = <&vreg_s7i_1p2>; + vdd-l3-l4-supply = <&vreg_s3g_1p8>; + vdd-l5-supply = <&vreg_bob2>; + vdd-l6-supply = <&vreg_bob2>; + vdd-l7-supply = <&vreg_bob1>; + + vreg_l1n_1p1: ldo1 { + regulator-name = "vreg_l1n_1p1"; + regulator-min-microvolt = <1104000>; + regulator-max-microvolt = <1104000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2n_1p1: ldo2 { + regulator-name = "vreg_l2n_1p1"; + regulator-min-microvolt = <1104000>; + regulator-max-microvolt = <1104000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3n_1p8: ldo3 { + regulator-name = "vreg_l3n_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l4n_1p8: ldo4 { + regulator-name = "vreg_l4n_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l5n_2p8: ldo5 { + regulator-name = "vreg_l5n_2p8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6n_2p8: ldo6 { + regulator-name = "vreg_l6n_2p8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7n_3p3: ldo7 { + regulator-name = "vreg_l7n_3p3"; + regulator-min-microvolt = <3304000>; + regulator-max-microvolt = <3304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; +}; + +&pm8550_flash { + status = "okay"; + + led-0 { + function = LED_FUNCTION_FLASH; + color = <LED_COLOR_ID_YELLOW>; + led-sources = <1>, <4>; + led-max-microamp = <500000>; + flash-max-microamp = <2000000>; + flash-max-timeout-us = <1280000>; + function-enumerator = <0>; + }; + + led-1 { + function = LED_FUNCTION_FLASH; + color = <LED_COLOR_ID_WHITE>; + led-sources = <2>, <3>; + led-max-microamp = <500000>; + flash-max-microamp = <2000000>; + flash-max-timeout-us = <1280000>; + function-enumerator = <1>; + }; +}; + +&pm8550_gpios { + volume_up_n: volume-up-n-state { + pins = "gpio6"; + function = "normal"; + bias-pull-up; + input-enable; + power-source = <1>; + }; +}; + +&pm8550_pwm { + status = "okay"; + + multi-led { + color = <LED_COLOR_ID_RGB>; + function = LED_FUNCTION_STATUS; + + #address-cells = <1>; + #size-cells = <0>; + + led@1 { + reg = <1>; + color = <LED_COLOR_ID_RED>; + }; + + led@2 { + reg = <2>; + color = <LED_COLOR_ID_GREEN>; + }; + + led@3 { + reg = <3>; + color = <LED_COLOR_ID_BLUE>; + }; + }; +}; + +&pon_pwrkey { + status = "okay"; +}; + +&pon_resin { + linux,code = <KEY_VOLUMEDOWN>; + + status = "okay"; +}; + +&pmih0108_eusb2_repeater { + status = "okay"; + + vdd18-supply = <&vreg_l15b_1p8>; + vdd3-supply = <&vreg_l5b_3p1>; +}; + +&qupv3_1 { + status = "okay"; +}; + +&tlmm { + /* reserved for secure world */ + gpio-reserved-ranges = <36 4>, <74 1>; +}; + +&uart7 { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/qcom/sm8750-qrd.dts b/arch/arm64/boot/dts/qcom/sm8750-qrd.dts new file mode 100644 index 000000000000..f77efab0aef9 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sm8750-qrd.dts @@ -0,0 +1,792 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved. + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> +#include "sm8750.dtsi" +#include "pm8010.dtsi" +#include "pm8550.dtsi" +#define PMK8550VE_SID 8 +#include "pm8550ve.dtsi" +#include "pmd8028.dtsi" +#include "pmih0108.dtsi" +#include "pmk8550.dtsi" +#include "pmr735d_a.dtsi" +#include "sm8750-pmics.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. SM8750 QRD"; + compatible = "qcom,sm8750-qrd", "qcom,sm8750"; + chassis-type = "handset"; + + aliases { + serial0 = &uart7; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + clocks { + xo_board: xo-board { + compatible = "fixed-clock"; + clock-frequency = <76800000>; + #clock-cells = <0>; + }; + + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + clock-frequency = <32000>; + #clock-cells = <0>; + }; + + bi_tcxo_div2: bi-tcxo-div2-clk { + compatible = "fixed-factor-clock"; + #clock-cells = <0>; + + clocks = <&rpmhcc RPMH_CXO_CLK>; + clock-mult = <1>; + clock-div = <2>; + }; + + bi_tcxo_ao_div2: bi-tcxo-ao-div2-clk { + compatible = "fixed-factor-clock"; + #clock-cells = <0>; + + clocks = <&rpmhcc RPMH_CXO_CLK_A>; + clock-mult = <1>; + clock-div = <2>; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-0 = <&volume_up_n>; + pinctrl-names = "default"; + + key-volume-up { + label = "Volume Up"; + linux,code = <KEY_VOLUMEUP>; + gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>; + debounce-interval = <15>; + linux,can-disable; + wakeup-source; + }; + }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + + regulator-always-on; + regulator-boot-on; + }; +}; + +&apps_rsc { + regulators-0 { + compatible = "qcom,pm8550-rpmh-regulators"; + + vdd-bob1-supply = <&vph_pwr>; + vdd-bob2-supply = <&vph_pwr>; + vdd-l1-l4-l10-supply = <&vreg_s3g_1p8>; + vdd-l2-l13-l14-supply = <&vreg_bob1>; + vdd-l3-supply = <&vreg_s7i_1p2>; + vdd-l5-l16-supply = <&vreg_bob1>; + vdd-l6-l7-supply = <&vreg_bob1>; + vdd-l8-l9-supply = <&vreg_bob1>; + vdd-l11-supply = <&vreg_s7i_1p2>; + vdd-l12-supply = <&vreg_s3g_1p8>; + vdd-l15-supply = <&vreg_s3g_1p8>; + vdd-l17-supply = <&vreg_bob2>; + + qcom,pmic-id = "b"; + + vreg_bob1: bob1 { + regulator-name = "vreg_bob1"; + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <4000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_bob2: bob2 { + regulator-name = "vreg_bob2"; + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1b_1p8: ldo1 { + regulator-name = "vreg_l1b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2b_3p0: ldo2 { + regulator-name = "vreg_l2b_3p0"; + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3048000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l4b_1p8: ldo4 { + regulator-name = "vreg_l4b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l5b_3p1: ldo5 { + regulator-name = "vreg_l5b_3p1"; + regulator-min-microvolt = <3100000>; + regulator-max-microvolt = <3148000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6b_1p8: ldo6 { + regulator-name = "vreg_l6b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7b_1p8: ldo7 { + regulator-name = "vreg_l7b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8b_1p8: ldo8 { + regulator-name = "vreg_l8b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9b_2p9: ldo9 { + regulator-name = "vreg_l9b_2p9"; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l10b_1p8: ldo10 { + regulator-name = "vreg_l10b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l11b_1p0: ldo11 { + regulator-name = "vreg_l11b_1p0"; + regulator-min-microvolt = <1064000>; + regulator-max-microvolt = <1292000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l12b_1p8: ldo12 { + regulator-name = "vreg_l12b_1p8"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l13b_3p0: ldo13 { + regulator-name = "vreg_l13b_3p0"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l14b_3p2: ldo14 { + regulator-name = "vreg_l14b_3p2"; + regulator-min-microvolt = <3200000>; + regulator-max-microvolt = <3200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l15b_1p8: ldo15 { + regulator-name = "vreg_l15b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l16b_2p8: ldo16 { + regulator-name = "vreg_l16b_2p8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l17b_2p5: ldo17 { + regulator-name = "vreg_l17b_2p5"; + regulator-min-microvolt = <2504000>; + regulator-max-microvolt = <2504000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-1 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + + vdd-l1-supply = <&vreg_s7i_1p2>; + vdd-l2-supply = <&vreg_s1d_0p97>; + vdd-l3-supply = <&vreg_s1d_0p97>; + vdd-s1-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + + qcom,pmic-id = "d"; + + vreg_s1d_0p97: smps1 { + regulator-name = "vreg_s1d_0p97"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <1100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s3d_1p2: smps3 { + regulator-name = "vreg_s3d_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1300000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s4d_0p85: smps4 { + regulator-name = "vreg_s4d_0p85"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1036000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1d_1p2: ldo1 { + regulator-name = "vreg_l1d_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2d_0p88: ldo2 { + regulator-name = "vreg_l2d_0p88"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3d_0p88: ldo3 { + regulator-name = "vreg_l3d_0p88"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-2 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + + vdd-l1-supply = <&vreg_s1d_0p97>; + vdd-l2-supply = <&vreg_s7i_1p2>; + vdd-l3-supply = <&vreg_s3g_1p8>; + vdd-s5-supply = <&vph_pwr>; + + qcom,pmic-id = "f"; + + vreg_s5f_0p5: smps5 { + regulator-name = "vreg_s5f_0p5"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1f_0p88: ldo1 { + regulator-name = "vreg_l1f_0p88"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2f_1p2: ldo2 { + regulator-name = "vreg_l2f_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3f_1p8: ldo3 { + regulator-name = "vreg_l3f_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + }; + + regulators-3 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + + vdd-l1-supply = <&vreg_s1d_0p97>; + vdd-l2-supply = <&vreg_s3g_1p8>; + vdd-l3-supply = <&vreg_s7i_1p2>; + vdd-s1-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + + qcom,pmic-id = "g"; + + vreg_s1g_0p5: smps1 { + regulator-name = "vreg_s1g_0p5"; + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <700000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s3g_1p8: smps3 { + regulator-name = "vreg_s3g_1p8"; + regulator-min-microvolt = <1856000>; + regulator-max-microvolt = <2000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s4g_0p75: smps4 { + regulator-name = "vreg_s4g_0p75"; + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <900000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1g_0p91: ldo1 { + regulator-name = "vreg_l1g_0p91"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <936000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2g_1p8: ldo2 { + regulator-name = "vreg_l2g_1p8"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1860000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3g_1p2: ldo3 { + regulator-name = "vreg_l3g_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1256000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-4 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + + vdd-l1-supply = <&vreg_s7i_1p2>; + vdd-l2-supply = <&vreg_s7i_1p2>; + vdd-l3-supply = <&vreg_s1d_0p97>; + vdd-s7-supply = <&vph_pwr>; + vdd-s8-supply = <&vph_pwr>; + + qcom,pmic-id = "i"; + + vreg_s7i_1p2: smps7 { + regulator-name = "vreg_s7i_1p2"; + regulator-min-microvolt = <1224000>; + regulator-max-microvolt = <1340000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s8i_0p9: smps8 { + regulator-name = "vreg_s8i_0p9"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <972000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1i_1p2: ldo1 { + regulator-name = "vreg_l1i_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2i_1p2: ldo2 { + regulator-name = "vreg_l2i_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3i_0p88: ldo3 { + regulator-name = "vreg_l3i_0p88"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-5 { + compatible = "qcom,pm8550vs-rpmh-regulators"; + + vdd-l1-supply = <&vreg_s1d_0p97>; + vdd-l2-supply = <&vreg_s7i_1p2>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + + qcom,pmic-id = "j"; + + vreg_s2j_1p1: smps2 { + regulator-name = "vreg_s2j_1p1"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s3j_1p1: smps3 { + regulator-name = "vreg_s3j_1p1"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + + vreg_l1j_0p91: ldo1 { + regulator-name = "vreg_l1j_0p91"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2j_1p2: ldo2 { + regulator-name = "vreg_l2j_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-6 { + compatible = "qcom,pm8010-rpmh-regulators"; + qcom,pmic-id = "m"; + + vdd-l1-l2-supply = <&vreg_s7i_1p2>; + vdd-l3-l4-supply = <&vreg_s3g_1p8>; + vdd-l5-supply = <&vreg_s3g_1p8>; + vdd-l6-supply = <&vreg_bob1>; + vdd-l7-supply = <&vreg_bob1>; + + vreg_l1m_1p1: ldo1 { + regulator-name = "vreg_l1m_1p1"; + regulator-min-microvolt = <1104000>; + regulator-max-microvolt = <1104000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2m_1p056: ldo2 { + regulator-name = "vreg_l2m_1p056"; + regulator-min-microvolt = <1056000>; + regulator-max-microvolt = <1056000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3m_2p8: ldo3 { + regulator-name = "vreg_l3m_2p8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l4m_2p8: ldo4 { + regulator-name = "vreg_l4m_2p8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l5m_1p8: ldo5 { + regulator-name = "vreg_l5m_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6m_2p8: ldo6 { + regulator-name = "vreg_l6m_2p8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7m_2p96: ldo7 { + regulator-name = "vreg_l7m_2p96"; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-7 { + compatible = "qcom,pm8010-rpmh-regulators"; + qcom,pmic-id = "n"; + + vdd-l1-l2-supply = <&vreg_s7i_1p2>; + vdd-l3-l4-supply = <&vreg_s7i_1p2>; + vdd-l5-supply = <&vreg_bob2>; + vdd-l6-supply = <&vreg_bob2>; + vdd-l7-supply = <&vreg_bob1>; + + vreg_l1n_1p1: ldo1 { + regulator-name = "vreg_l1n_1p1"; + regulator-min-microvolt = <1104000>; + regulator-max-microvolt = <1104000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2n_1p1: ldo2 { + regulator-name = "vreg_l2n_1p1"; + regulator-min-microvolt = <1104000>; + regulator-max-microvolt = <1104000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM + RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3n_1p8: ldo3 { + regulator-name = "vreg_l3n_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l4n_1p8: ldo4 { + regulator-name = "vreg_l4n_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l5n_2p8: ldo5 { + regulator-name = "vreg_l5n_2p8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6n_2p8: ldo6 { + regulator-name = "vreg_l6n_2p8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7n_3p3: ldo7 { + regulator-name = "vreg_l7n_3p3"; + regulator-min-microvolt = <3304000>; + regulator-max-microvolt = <3304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; +}; + +&pm8550_flash { + status = "okay"; + + led-0 { + function = LED_FUNCTION_FLASH; + color = <LED_COLOR_ID_YELLOW>; + led-sources = <1>, <4>; + led-max-microamp = <500000>; + flash-max-microamp = <2000000>; + flash-max-timeout-us = <1280000>; + function-enumerator = <0>; + }; + + led-1 { + function = LED_FUNCTION_FLASH; + color = <LED_COLOR_ID_WHITE>; + led-sources = <2>, <3>; + led-max-microamp = <500000>; + flash-max-microamp = <2000000>; + flash-max-timeout-us = <1280000>; + function-enumerator = <1>; + }; +}; + +&pm8550_gpios { + volume_up_n: volume-up-n-state { + pins = "gpio6"; + function = "normal"; + bias-pull-up; + input-enable; + power-source = <1>; + }; +}; + +&pm8550_pwm { + status = "okay"; + + multi-led { + color = <LED_COLOR_ID_RGB>; + function = LED_FUNCTION_STATUS; + + #address-cells = <1>; + #size-cells = <0>; + + led@1 { + reg = <1>; + color = <LED_COLOR_ID_RED>; + }; + + led@2 { + reg = <2>; + color = <LED_COLOR_ID_GREEN>; + }; + + led@3 { + reg = <3>; + color = <LED_COLOR_ID_BLUE>; + }; + }; +}; + +&pon_pwrkey { + status = "okay"; +}; + +&pon_resin { + linux,code = <KEY_VOLUMEDOWN>; + + status = "okay"; +}; + +&pmih0108_eusb2_repeater { + status = "okay"; + + vdd18-supply = <&vreg_l15b_1p8>; + vdd3-supply = <&vreg_l5b_3p1>; +}; + +&qupv3_1 { + status = "okay"; +}; + +&tlmm { + /* reserved for secure world */ + gpio-reserved-ranges = <36 4>, <74 1>; +}; + +&uart7 { + status = "okay"; +}; -- 2.46.1 ^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v2 6/6] arm64: defconfig: Enable SM8750 SoC base configs 2024-11-12 0:49 [PATCH v2 0/6] dts: qcom: Introduce SM8750 device trees Melody Olvera ` (4 preceding siblings ...) 2024-11-12 0:49 ` [PATCH v2 5/6] arm64: dts: qcom: Add SM8750 MTP and QRD boards Melody Olvera @ 2024-11-12 0:49 ` Melody Olvera 5 siblings, 0 replies; 12+ messages in thread From: Melody Olvera @ 2024-11-12 0:49 UTC (permalink / raw) To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Catalin Marinas, Will Deacon, Geert Uytterhoeven, Dmitry Baryshkov, Neil Armstrong, Arnd Bergmann, Nícolas F . R . A . Prado, Trilok Soni, Satya Durga Srinivasu Prabhala Cc: linux-arm-msm, devicetree, linux-kernel, linux-arm-kernel, Melody Olvera, Raviteja Laggyshetty, Krzysztof Kozlowski Enable GCC, TCSRCC, Pinctrl and Interconnect configs for Qualcomm's SM8750 SoC which is required to boot SM8750 MTP/QRD boards to a console shell. The configs are required to be marked as builtin and not modules due to the console driver dependencies. Co-developed-by: Raviteja Laggyshetty <quic_rlaggysh@quicinc.com> Signed-off-by: Raviteja Laggyshetty <quic_rlaggysh@quicinc.com> Signed-off-by: Melody Olvera <quic_molvera@quicinc.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> --- arch/arm64/configs/defconfig | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig index d13218d0c30f..ee8c7fc184e8 100644 --- a/arch/arm64/configs/defconfig +++ b/arch/arm64/configs/defconfig @@ -630,6 +630,7 @@ CONFIG_PINCTRL_SM8350=y CONFIG_PINCTRL_SM8450=y CONFIG_PINCTRL_SM8550=y CONFIG_PINCTRL_SM8650=y +CONFIG_PINCTRL_SM8750=y CONFIG_PINCTRL_X1E80100=y CONFIG_PINCTRL_QCOM_SPMI_PMIC=y CONFIG_PINCTRL_LPASS_LPI=m @@ -1361,6 +1362,7 @@ CONFIG_SM_GCC_8350=y CONFIG_SM_GCC_8450=y CONFIG_SM_GCC_8550=y CONFIG_SM_GCC_8650=y +CONFIG_SM_GCC_8750=y CONFIG_SM_GPUCC_6115=m CONFIG_SM_GPUCC_8150=y CONFIG_SM_GPUCC_8250=y @@ -1370,6 +1372,7 @@ CONFIG_SM_GPUCC_8550=m CONFIG_SM_GPUCC_8650=m CONFIG_SM_TCSRCC_8550=y CONFIG_SM_TCSRCC_8650=y +CONFIG_SM_TCSRCC_8750=y CONFIG_SM_VIDEOCC_8250=y CONFIG_QCOM_HFPLL=y CONFIG_CLK_GFM_LPASS_SM8250=m @@ -1649,6 +1652,7 @@ CONFIG_INTERCONNECT_QCOM_SM8350=y CONFIG_INTERCONNECT_QCOM_SM8450=y CONFIG_INTERCONNECT_QCOM_SM8550=y CONFIG_INTERCONNECT_QCOM_SM8650=y +CONFIG_INTERCONNECT_QCOM_SM8750=y CONFIG_INTERCONNECT_QCOM_X1E80100=y CONFIG_COUNTER=m CONFIG_RZ_MTU3_CNT=m -- 2.46.1 ^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2024-11-18 22:16 UTC | newest] Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2024-11-12 0:49 [PATCH v2 0/6] dts: qcom: Introduce SM8750 device trees Melody Olvera 2024-11-12 0:49 ` [PATCH v2 1/6] dt-bindings: arm: qcom: Document sm8750 SoC and boards Melody Olvera 2024-11-15 14:49 ` Dmitry Baryshkov 2024-11-18 22:08 ` Melody Olvera 2024-11-12 0:49 ` [PATCH v2 2/6] arm64: dts: qcom: Add pmd8028 and pmih0108 PMICs Melody Olvera 2024-11-15 14:58 ` Dmitry Baryshkov 2024-11-18 22:16 ` Melody Olvera 2024-11-12 0:49 ` [PATCH v2 3/6] arm64: dts: qcom: Add base SM8750 dtsi Melody Olvera 2024-11-15 20:26 ` Konrad Dybcio 2024-11-12 0:49 ` [PATCH v2 4/6] arm64: dts: qcom: sm8750: Add pmic dtsi Melody Olvera 2024-11-12 0:49 ` [PATCH v2 5/6] arm64: dts: qcom: Add SM8750 MTP and QRD boards Melody Olvera 2024-11-12 0:49 ` [PATCH v2 6/6] arm64: defconfig: Enable SM8750 SoC base configs Melody Olvera
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®