[PATCH v2 06/13] arm64: dts: qcom: lemans-evk: Enable PCIe support

[Wasim Nazir <wasim.nazir@oss.qualcomm.com>]

From: Sushrut Shree Trivedi <quic_sushruts@quicinc.com>

Enable PCIe0 and PCIe1 along with the respective phy-nodes.

PCIe0 is routed to an m.2 E key connector on the mainboard for wifi
attaches while PCIe1 routes to a standard PCIe x4 expansion slot.

Signed-off-by: Sushrut Shree Trivedi <quic_sushruts@quicinc.com>
Signed-off-by: Wasim Nazir <wasim.nazir@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/lemans-evk.dts | 82 +++++++++++++++++++++++++++++++++
 1 file changed, 82 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/lemans-evk.dts b/arch/arm64/boot/dts/qcom/lemans-evk.dts
index 196c5ee0dd34..7528fa1c661a 100644
--- a/arch/arm64/boot/dts/qcom/lemans-evk.dts
+++ b/arch/arm64/boot/dts/qcom/lemans-evk.dts
@@ -379,6 +379,40 @@ &mdss0_dp1_phy {
 	status = "okay";
 };
 
+&pcie0 {
+	perst-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie0_default_state>;
+
+	status = "okay";
+};
+
+&pcie0_phy {
+	vdda-phy-supply = <&vreg_l5a>;
+	vdda-pll-supply = <&vreg_l1c>;
+
+	status = "okay";
+};
+
+&pcie1 {
+	perst-gpios = <&tlmm 4 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie1_default_state>;
+
+	status = "okay";
+};
+
+&pcie1_phy {
+	vdda-phy-supply = <&vreg_l5a>;
+	vdda-pll-supply = <&vreg_l1c>;
+
+	status = "okay";
+};
+
 &qupv3_id_0 {
 	status = "okay";
 };
@@ -395,6 +429,54 @@ &sleep_clk {
 	clock-frequency = <32768>;
 };
 
+&tlmm {
+	pcie0_default_state: pcie0-default-state {
+		clkreq-pins {
+			pins = "gpio1";
+			function = "pcie0_clkreq";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-pins {
+			pins = "gpio2";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+
+		wake-pins {
+			pins = "gpio0";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	pcie1_default_state: pcie1-default-state {
+		clkreq-pins {
+			pins = "gpio3";
+			function = "pcie1_clkreq";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-pins {
+			pins = "gpio4";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+
+		wake-pins {
+			pins = "gpio5";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+};
+
 &uart10 {
 	compatible = "qcom,geni-debug-uart";
 	pinctrl-0 = <&qup_uart10_default>;

-- 
2.51.0