From: Manikanta Maddireddy <mmaddireddy@nvidia.com>
To: <bhelgaas@google.com>, <lpieralisi@kernel.org>,
<kwilczynski@kernel.org>, <mani@kernel.org>, <robh@kernel.org>,
<krzk+dt@kernel.org>, <conor+dt@kernel.org>,
<thierry.reding@gmail.com>, <jonathanh@nvidia.com>,
<jingoohan1@gmail.com>, <vidyas@nvidia.com>, <cassel@kernel.org>,
<18255117159@163.com>
Cc: <linux-pci@vger.kernel.org>, <devicetree@vger.kernel.org>,
<linux-tegra@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
"Manikanta Maddireddy" <mmaddireddy@nvidia.com>
Subject: [PATCH V4 05/22] PCI: tegra194: Refactor LTSSM state polling on surprise down
Date: Mon, 26 Jan 2026 13:15:02 +0530 [thread overview]
Message-ID: <20260126074519.3426742-6-mmaddireddy@nvidia.com> (raw)
In-Reply-To: <20260126074519.3426742-1-mmaddireddy@nvidia.com>
From: Vidya Sagar <vidyas@nvidia.com>
On surprise down, LTSSM state transits from L0 -> Recovery.RcvrLock ->
Recovery.RcvrSpeed -> Gen1 Recovery.RcvrLock -> Detect. Recovery.RcvrLock
and Recovery.RcvrSpeed transit times are 24 msec and 48 msec respectively.
So, the total time taken to transit from L0 to detect state is ~96 msec.
Hence, increase the poll time to 120 msec.
Disable the LTSSM state after it transits to detect to avoid LTSSM
toggling between polling and detect states.
tegra_pcie_dw_pme_turnoff() function is called in non-atomic context
only, so use the non-atomic poll function.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
---
V4:
* None
V3:
* Addressed review comments from Bjorn
* Reworded the commit message
V2:
* None
drivers/pci/controller/dwc/pcie-tegra194.c | 55 +++++++++++++---------
1 file changed, 32 insertions(+), 23 deletions(-)
diff --git a/drivers/pci/controller/dwc/pcie-tegra194.c b/drivers/pci/controller/dwc/pcie-tegra194.c
index 04ff211deaea..d3d577d5f67b 100644
--- a/drivers/pci/controller/dwc/pcie-tegra194.c
+++ b/drivers/pci/controller/dwc/pcie-tegra194.c
@@ -138,7 +138,11 @@
#define APPL_DEBUG_PM_LINKST_IN_L0 0x11
#define APPL_DEBUG_LTSSM_STATE_MASK GENMASK(8, 3)
#define APPL_DEBUG_LTSSM_STATE_SHIFT 3
-#define LTSSM_STATE_PRE_DETECT 5
+#define LTSSM_STATE_DETECT_QUIET 0x00
+#define LTSSM_STATE_DETECT_ACT 0x08
+#define LTSSM_STATE_PRE_DETECT_QUIET 0x28
+#define LTSSM_STATE_DETECT_WAIT 0x30
+#define LTSSM_STATE_L2_IDLE 0xa8
#define APPL_RADM_STATUS 0xE4
#define APPL_PM_XMT_TURNOFF_STATE BIT(0)
@@ -202,7 +206,8 @@
#define PME_ACK_DELAY 100 /* 100 us */
#define PME_ACK_TIMEOUT 10000 /* 10 ms */
-#define LTSSM_TIMEOUT 50000 /* 50ms */
+#define LTSSM_DELAY 10000 /* 10 ms */
+#define LTSSM_TIMEOUT 120000 /* 120 ms */
#define GEN3_GEN4_EQ_PRESET_INIT 5
@@ -1593,23 +1598,22 @@ static void tegra_pcie_dw_pme_turnoff(struct tegra_pcie_dw *pcie)
data &= ~APPL_PINMUX_PEX_RST;
appl_writel(pcie, data, APPL_PINMUX);
+ err = readl_poll_timeout(pcie->appl_base + APPL_DEBUG, data,
+ ((data & APPL_DEBUG_LTSSM_STATE_MASK) == LTSSM_STATE_DETECT_QUIET) ||
+ ((data & APPL_DEBUG_LTSSM_STATE_MASK) == LTSSM_STATE_DETECT_ACT) ||
+ ((data & APPL_DEBUG_LTSSM_STATE_MASK) == LTSSM_STATE_PRE_DETECT_QUIET) ||
+ ((data & APPL_DEBUG_LTSSM_STATE_MASK) == LTSSM_STATE_DETECT_WAIT),
+ LTSSM_DELAY, LTSSM_TIMEOUT);
+ if (err)
+ dev_info(pcie->dev, "Link didn't go to detect state\n");
+
/*
- * Some cards do not go to detect state even after de-asserting
- * PERST#. So, de-assert LTSSM to bring link to detect state.
+ * Deassert LTSSM state to stop the state toggling between
+ * polling and detect.
*/
data = readl(pcie->appl_base + APPL_CTRL);
data &= ~APPL_CTRL_LTSSM_EN;
writel(data, pcie->appl_base + APPL_CTRL);
-
- err = readl_poll_timeout_atomic(pcie->appl_base + APPL_DEBUG,
- data,
- ((data &
- APPL_DEBUG_LTSSM_STATE_MASK) >>
- APPL_DEBUG_LTSSM_STATE_SHIFT) ==
- LTSSM_STATE_PRE_DETECT,
- 1, LTSSM_TIMEOUT);
- if (err)
- dev_info(pcie->dev, "Link didn't go to detect state\n");
}
/*
* DBI registers may not be accessible after this as PLL-E would be
@@ -1677,19 +1681,24 @@ static void pex_ep_event_pex_rst_assert(struct tegra_pcie_dw *pcie)
if (pcie->ep_state == EP_STATE_DISABLED)
return;
- /* Disable LTSSM */
+ ret = readl_poll_timeout(pcie->appl_base + APPL_DEBUG, val,
+ ((val & APPL_DEBUG_LTSSM_STATE_MASK) == LTSSM_STATE_DETECT_QUIET) ||
+ ((val & APPL_DEBUG_LTSSM_STATE_MASK) == LTSSM_STATE_DETECT_ACT) ||
+ ((val & APPL_DEBUG_LTSSM_STATE_MASK) == LTSSM_STATE_PRE_DETECT_QUIET) ||
+ ((val & APPL_DEBUG_LTSSM_STATE_MASK) == LTSSM_STATE_DETECT_WAIT) ||
+ ((val & APPL_DEBUG_LTSSM_STATE_MASK) == LTSSM_STATE_L2_IDLE),
+ LTSSM_DELAY, LTSSM_TIMEOUT);
+ if (ret)
+ dev_err(pcie->dev, "LTSSM state: 0x%x timeout: %d\n", val, ret);
+
+ /*
+ * Deassert LTSSM state to stop the state toggling between
+ * polling and detect.
+ */
val = appl_readl(pcie, APPL_CTRL);
val &= ~APPL_CTRL_LTSSM_EN;
appl_writel(pcie, val, APPL_CTRL);
- ret = readl_poll_timeout(pcie->appl_base + APPL_DEBUG, val,
- ((val & APPL_DEBUG_LTSSM_STATE_MASK) >>
- APPL_DEBUG_LTSSM_STATE_SHIFT) ==
- LTSSM_STATE_PRE_DETECT,
- 1, LTSSM_TIMEOUT);
- if (ret)
- dev_err(pcie->dev, "Failed to go Detect state: %d\n", ret);
-
reset_control_assert(pcie->core_rst);
tegra_pcie_disable_phy(pcie);
--
2.34.1
next prev parent reply other threads:[~2026-01-26 7:46 UTC|newest]
Thread overview: 33+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-01-26 7:44 [PATCH V4 00/22] Enhancements to pcie-tegra194 driver Manikanta Maddireddy
2026-01-26 7:44 ` [PATCH V4 01/22] PCI: tegra194: Use devm_gpiod_get_optional() to parse "nvidia,refclk-select" Manikanta Maddireddy
2026-01-26 7:44 ` [PATCH V4 02/22] PCI: tegra194: Drive CLKREQ signal low explicitly Manikanta Maddireddy
2026-01-26 7:45 ` [PATCH V4 03/22] PCI: tegra194: Fix polling delay for L2 state Manikanta Maddireddy
2026-01-26 7:45 ` [PATCH V4 04/22] PCI: tegra194: Apply pinctrl settings for both PCIe RP and EP Manikanta Maddireddy
2026-01-30 17:21 ` Jon Hunter
2026-02-02 5:22 ` Manikanta Maddireddy
2026-01-26 7:45 ` Manikanta Maddireddy [this message]
2026-01-26 7:45 ` [PATCH V4 06/22] PCI: tegra194: Disable direct speed change for EP Manikanta Maddireddy
2026-01-26 7:45 ` [PATCH V4 07/22] PCI: tegra194: Calibrate P2U for endpoint mode Manikanta Maddireddy
2026-01-26 7:45 ` [PATCH V4 08/22] PCI: tegra194: Free resources during controller deinitialization Manikanta Maddireddy
2026-01-26 7:45 ` [PATCH V4 09/22] PCI: tegra194: Remove IRQF_ONESHOT flag during Endpoint interrupt registration Manikanta Maddireddy
2026-01-26 7:45 ` [PATCH V4 10/22] PCI: tegra194: Enable DMA interrupt Manikanta Maddireddy
2026-01-26 7:45 ` [PATCH V4 11/22] PCI: tegra194: Enable hardware hot reset mode in Endpoint Manikanta Maddireddy
2026-01-26 7:45 ` [PATCH V4 12/22] PCI: tegra194: Allow system suspend when the Endpoint link is not up Manikanta Maddireddy
2026-01-26 7:45 ` [PATCH V4 13/22] PCI: tegra194: Disable L1.2 capability of Tegra234 EP Manikanta Maddireddy
2026-01-26 7:45 ` [PATCH V4 14/22] PCI: tegra194: Set LTR message request before PCIe link up Manikanta Maddireddy
2026-01-26 7:45 ` [PATCH V4 15/22] PCI: tegra194: Don't force the device into the D0 state before L2 Manikanta Maddireddy
2026-02-02 13:27 ` Jon Hunter
2026-01-26 7:45 ` [PATCH V4 16/22] PCI: tegra194: Free up EP resources during remove() Manikanta Maddireddy
2026-02-02 13:28 ` Jon Hunter
2026-01-26 7:45 ` [PATCH V4 17/22] dt-bindings: PCI: tegra194: Add monitor clock support Manikanta Maddireddy
2026-01-29 16:40 ` Rob Herring
2026-02-02 4:34 ` Manikanta Maddireddy
2026-01-26 7:45 ` [PATCH V4 18/22] PCI: tegra194: Add core " Manikanta Maddireddy
2026-01-26 7:45 ` [PATCH V4 19/22] PCI: tegra194: Add ASPM L1 entrance latency config Manikanta Maddireddy
2026-02-02 13:28 ` Jon Hunter
2026-01-26 7:45 ` [PATCH V4 20/22] PCI: tegra194: Use HW version number Manikanta Maddireddy
2026-02-02 13:30 ` Jon Hunter
2026-01-26 7:45 ` [PATCH V4 21/22] PCI: tegra194: Fix CBB timeout caused by DBI access before core power-on Manikanta Maddireddy
2026-01-26 7:45 ` [PATCH V4 22/22] PCI: tegra194: Disable PERST IRQ only in Endpoint mode Manikanta Maddireddy
2026-02-02 13:35 ` [PATCH V4 00/22] Enhancements to pcie-tegra194 driver Jon Hunter
2026-02-05 7:55 ` Manivannan Sadhasivam
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260126074519.3426742-6-mmaddireddy@nvidia.com \
--to=mmaddireddy@nvidia.com \
--cc=18255117159@163.com \
--cc=bhelgaas@google.com \
--cc=cassel@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=jingoohan1@gmail.com \
--cc=jonathanh@nvidia.com \
--cc=krzk+dt@kernel.org \
--cc=kwilczynski@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
--cc=linux-tegra@vger.kernel.org \
--cc=lpieralisi@kernel.org \
--cc=mani@kernel.org \
--cc=robh@kernel.org \
--cc=thierry.reding@gmail.com \
--cc=vidyas@nvidia.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®