[PATCH 4/5] arm64: dts: qcom: nord-rrd: Enable USB ports

[Shawn Guo <shengchao.guo@oss.qualcomm.com>]

Describe the RRD USB topology. Enable i2c9 and add the two NXP PTN3222
eUSB2 repeaters for USB_0 and USB_1, supplied from vreg_l3l_1p8 and a new
fixed 3.3 V pre-regulator, and reset through pmau0102_i GPIOs 9 and 10.

Add the onsemi FUSB15201 Type-C controller at 0x50 with its interrupt and
pinctrl state on pmau0102_i gpio8. Unlike RIDE, only port A of
the controller is wired on this board, to USB_0, so a single
usb-c-connector is described and port B is left out. USB_0 is configured
for OTG with usb-role-switch and its HS and SS endpoints are linked to
the dwc3 HS endpoint and the QMP combo PHY SS output.

USB_1 is a fixed host port feeding an on-board Genesys Logic GL3590 USB
3.1 hub. Add the HS and SS hub pair as children of USB_1, linked with
peer-hub, with the HS half reset via TLMM GPIO 170 and the SS half
additionally supplied by a fixed 1.2 V rail.

Assisted-by: LLM
Signed-off-by: Shawn Guo <shengchao.guo@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/nord-rrd.dts | 169 ++++++++++++++++++++++++++
 1 file changed, 169 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/nord-rrd.dts b/arch/arm64/boot/dts/qcom/nord-rrd.dts
index c547963371b4..c2f870ac4234 100644
--- a/arch/arm64/boot/dts/qcom/nord-rrd.dts
+++ b/arch/arm64/boot/dts/qcom/nord-rrd.dts
@@ -6,6 +6,7 @@
 /dts-v1/;
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 
 #include "nord-embedded.dtsi"
@@ -53,6 +54,22 @@ bi_tcxo_ao_div2: bi-tcxo-ao-div2-clk {
 			clock-div = <2>;
 		};
 	};
+
+	vreg_per_3p3: regulator-per-3p3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_per_3p3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	vreg_hub_1p2: regulator-hub-1p2 {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_hub_1p2";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-always-on;
+	};
 };
 
 &apps_rsc {
@@ -377,6 +394,86 @@ rtc@32 {
 	};
 };
 
+&i2c9 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	usb0_repeater: redriver@43 {
+		compatible = "nxp,ptn3222";
+		reg = <0x43>;
+		#phy-cells = <0>;
+		vdd1v8-supply = <&vreg_l3l_1p8>;
+		vdd3v3-supply = <&vreg_per_3p3>;
+		reset-gpios = <&pmau0102_i_gpios 9 GPIO_ACTIVE_LOW>;
+	};
+
+	usb1_repeater: redriver@4f {
+		compatible = "nxp,ptn3222";
+		reg = <0x4f>;
+		#phy-cells = <0>;
+		vdd1v8-supply = <&vreg_l3l_1p8>;
+		vdd3v3-supply = <&vreg_per_3p3>;
+		reset-gpios = <&pmau0102_i_gpios 10 GPIO_ACTIVE_LOW>;
+	};
+
+	typec@50 {
+		compatible = "onnn,fusb15201";
+		reg = <0x50>;
+		interrupts-extended = <&pmau0102_i_gpios 8 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-0 = <&usb_pd_int_default>;
+		pinctrl-names = "default";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/*
+		 * Only port A of the controller is wired up on this board, to
+		 * USB_0. Port B is left unconnected.
+		 */
+		connector@0 {
+			compatible = "usb-c-connector";
+			reg = <0>;
+			label = "USB-C0";
+			power-role = "dual";
+			data-role = "dual";
+			try-power-role = "sink";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					usb_0_con_hs: endpoint {
+						remote-endpoint = <&usb_0_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					usb_0_con_ss: endpoint {
+						remote-endpoint = <&usb_0_qmpphy_usb_ss_out>;
+					};
+				};
+			};
+		};
+	};
+};
+
+&pmau0102_i_gpios {
+	usb_pd_int_default: usb-pd-int-state {
+		pins = "gpio8";
+		function = "normal";
+		input-enable;
+		bias-pull-up;
+		power-source = <0>;
+	};
+};
+
 &qupv3_0 {
 	firmware-name = "qcom/nord/qupv3fw.elf";
 
@@ -459,3 +556,75 @@ &ufs_mem_phy {
 
 	status = "okay";
 };
+
+&usb_0 {
+	dr_mode = "otg";
+	usb-role-switch;
+
+	status = "okay";
+};
+
+&usb_0_dwc3_hs {
+	remote-endpoint = <&usb_0_con_hs>;
+};
+
+&usb_0_hsphy {
+	vdd-supply = <&vreg_l1h_0p9>;
+	vdda12-supply = <&vreg_l2h_1p2>;
+
+	phys = <&usb0_repeater>;
+
+	status = "okay";
+};
+
+&usb_0_qmpphy {
+	vdda-phy-supply = <&vreg_l2k_0p9>;
+	vdda-pll-supply = <&vreg_l2h_1p2>;
+
+	status = "okay";
+};
+
+&usb_0_qmpphy_usb_ss_out {
+	remote-endpoint = <&usb_0_con_ss>;
+};
+
+&usb_1 {
+	dr_mode = "host";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	status = "okay";
+
+	hub_hs: hub@1 {
+		compatible = "usb5e3,610";
+		reg = <1>;
+		reset-gpios = <&tlmm 170 GPIO_ACTIVE_LOW>;
+		vdd-supply = <&vreg_per_3p3>;
+		peer-hub = <&hub_ss>;
+	};
+
+	hub_ss: hub@2 {
+		compatible = "usb5e3,625";
+		reg = <2>;
+		vdd-supply = <&vreg_per_3p3>;
+		vdd12-supply = <&vreg_hub_1p2>;
+		peer-hub = <&hub_hs>;
+	};
+};
+
+&usb_1_hsphy {
+	vdd-supply = <&vreg_l1h_0p9>;
+	vdda12-supply = <&vreg_l2h_1p2>;
+
+	phys = <&usb1_repeater>;
+
+	status = "okay";
+};
+
+&usb_1_qmpphy {
+	vdda-phy-supply = <&vreg_l2k_0p9>;
+	vdda-pll-supply = <&vreg_l2h_1p2>;
+
+	status = "okay";
+};
-- 
2.43.0