From: Lee Jones <lee@kernel.org>
To: Imre Kaloz <kaloz@kernel.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>,
linux-mips@vger.kernel.org, linux-kernel@vger.kernel.org,
mfd@lists.linux.dev
Subject: Re: [PATCH 31/38] mfd: ioc3: add IP34 system-board entry to ioc3_infos[]
Date: Fri, 2 Oct 2026 11:02:04 +0100 [thread overview]
Message-ID: <20261002100204.GB13860@google.com> (raw)
In-Reply-To: <e9b125b8ab2422717072f447c318eff41062bd79.1790857966.git.kaloz@kernel.org>
On Thu, 01 Oct 2026, Imre Kaloz wrote:
> Register the Fuel system board's on-board IOC3 and its M48T35, whose
> year register counts from 1968 as on other IP35-family machines.
> Bridge-side detection was already merged in commit 2c4288719806 ("MIPS:
> PCI: Add detection of IOC3 on IO7, IO8, IO9 and Fuel"), which matches
> the board part number "030-1707-"; the cell table had no entry to go
> with it. Without one the IOC3 falls to the CAD DUO default, which
> instantiates no serial cell, so Fuel comes up with no ttyS0.
I received 26 and 31. Where is the rest of the set?
I'd like to have full context please.
--
Lee Jones
next prev parent reply other threads:[~2026-10-02 10:02 UTC|newest]
Thread overview: 42+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-10-01 16:11 [PATCH 00/38] MIPS: SGI-IP27: add support for the IP35 (Bedrock hub) machines Imre Kaloz
2026-10-01 16:11 ` [PATCH 01/38] MIPS: Xtalk: guard the widget identification table from assembly Imre Kaloz
2026-10-01 16:11 ` [PATCH 02/38] MIPS: SGI-IP27: dump the NMI save areas the CPU scan recorded Imre Kaloz
2026-10-01 16:11 ` [PATCH 03/38] MIPS: SGI-IP27: add REMOTE_HUB_PI_S()/REMOTE_HUB_PI_L() Imre Kaloz
2026-10-01 16:11 ` [PATCH 04/38] MIPS: SGI-IP27: detect Bedrock hubs at boot Imre Kaloz
2026-10-01 16:11 ` [PATCH 05/38] MIPS: SGI-IP27: widen Kconfig for the Bedrock-based machines Imre Kaloz
2026-10-01 16:11 ` [PATCH 06/38] MIPS: SGI-IP27: fold the dead SN1 arm out of klconfig.h Imre Kaloz
2026-10-01 16:11 ` [PATCH 07/38] MIPS: SGI-IP27: choose the node address layout at runtime Imre Kaloz
2026-10-01 16:11 ` [PATCH 08/38] MIPS: SGI-IP27: add the Bedrock hub register windows Imre Kaloz
2026-10-01 16:11 ` [PATCH 09/38] MIPS: SGI-IP27: decode a Bedrock hub's node id and system size Imre Kaloz
2026-10-01 16:11 ` [PATCH 10/38] MIPS: SGI-IP27: put a Bedrock hub's boot CPU in slot 0 Imre Kaloz
2026-10-01 16:11 ` [PATCH 11/38] MIPS: SGI-IP27: lay out node memory in 1GB banks on Bedrock hubs Imre Kaloz
2026-10-01 16:11 ` [PATCH 12/38] MIPS: SGI-IP27: reserve the bottom 64MB of node 0 " Imre Kaloz
2026-10-01 16:11 ` [PATCH 13/38] MIPS: SGI-IP27: route interrupt masks and slices through both PIs Imre Kaloz
2026-10-01 16:11 ` [PATCH 14/38] MIPS: SGI-IP27: address a CPU's own PI for NMI, IPI and RT counter Imre Kaloz
2026-10-01 16:11 ` [PATCH 15/38] MIPS: SGI-IP27: take a CPU's node from the CPU table in per_cpu_init() Imre Kaloz
2026-10-01 16:11 ` [PATCH 16/38] MIPS: SGI-IP27: resolve the mapped-kernel node shift at runtime Imre Kaloz
2026-10-01 16:11 ` [PATCH 17/38] MIPS: SGI-IP27: load the kernel at node offset 0x40000 Imre Kaloz
2026-10-01 16:11 ` [PATCH 18/38] MIPS: SGI-IP27: xbow_probe(): recognize KLTYPE_PBRICK_XBOW Imre Kaloz
2026-10-01 16:11 ` [PATCH 19/38] MIPS: ip27_defconfig: enable the IOC3 MFD, its cell drivers and tg3 Imre Kaloz
2026-10-01 16:11 ` [PATCH 20/38] net: ethernet: sgi: ioc3-eth: apply the DMA attributes only to 64-bit addresses Imre Kaloz
2026-10-01 16:11 ` [PATCH 21/38] MIPS: SGI-IP27: route XBridge and PIC DMA through the 32-bit window Imre Kaloz
2026-10-01 16:11 ` [PATCH 22/38] MIPS: SGI-IP27: recognize the PXBow crossbar Imre Kaloz
2026-10-01 16:11 ` [PATCH 23/38] MIPS: PCI: xtalk-bridge: recognize the PIC widget's 64-bit-only registers Imre Kaloz
2026-10-01 16:11 ` [PATCH 24/38] MIPS: PCI: xtalk-bridge: match PIC's register-level differences Imre Kaloz
2026-10-01 16:12 ` [PATCH 25/38] rtc: m48t35: support the SGI IP35 timekeeper's 1968 year base Imre Kaloz
2026-10-01 16:12 ` [PATCH 26/38] mfd: ioc3: add support for IOC4 Imre Kaloz
2026-10-01 16:12 ` [PATCH 27/38] MIPS: SGI-IP27: dispatch the early console between IOC3 and IOC4 Imre Kaloz
2026-10-01 16:12 ` [PATCH 28/38] MIPS: SGI-IP27: add L1 system controller support Imre Kaloz
2026-10-01 16:12 ` [PATCH 29/38] MIPS: SGI-IP27: wire the L1 into reset and the Ethernet address Imre Kaloz
2026-10-01 16:12 ` [PATCH 30/38] MIPS: PCI: xtalk-bridge: take the board part number from the L1 Imre Kaloz
2026-10-01 16:12 ` [PATCH 31/38] mfd: ioc3: add IP34 system-board entry to ioc3_infos[] Imre Kaloz
2026-10-02 10:02 ` Lee Jones [this message]
2026-10-02 10:29 ` Imre Kaloz
2026-10-01 16:12 ` [PATCH 32/38] net: ethernet: sgi: ioc3-eth: fall back to the platform MAC address Imre Kaloz
2026-10-01 16:12 ` [PATCH 33/38] MIPS: SGI-IP27: don't register a w1 master on an XBridge or PIC Imre Kaloz
2026-10-01 16:12 ` [PATCH 34/38] MIPS: SGI-IP27: report a Bedrock machine as SGI IP35 Imre Kaloz
2026-10-01 16:12 ` [PATCH 35/38] MIPS: SGI-IP27: identify the machine by the L1 brick type Imre Kaloz
2026-10-01 16:12 ` [PATCH 36/38] MIPS: SGI-IP27: register the Odyssey graphics widget Imre Kaloz
2026-10-01 16:12 ` [PATCH 37/38] MIPS: SGI-IP27: take the console from the KLCONFIG header on IP35 Imre Kaloz
2026-10-01 16:12 ` [PATCH 38/38] MIPS: SGI-IP27: give each CPU its own topology package id Imre Kaloz
2026-10-02 15:46 ` [PATCH 00/38] MIPS: SGI-IP27: add support for the IP35 (Bedrock hub) machines Thomas Bogendoerfer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261002100204.GB13860@google.com \
--to=lee@kernel.org \
--cc=kaloz@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mips@vger.kernel.org \
--cc=mfd@lists.linux.dev \
--cc=tsbogend@alpha.franken.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®